Installation Of High Mast Solar Light At Birpara Central Hostel St Boys At Birpara Under Madarihat Birpara Block
Tender Value
5.11 Lakhs
Estimated cost
Bid Submission
16 Jan 2024
0 days left
EMD
10227
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
madarihat → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Installation Of High Mast Solar Light At Birpara Central Hostel St Boys At Birpara Under Madarihat Birpara Block
BOQ
| Sl. No. | Item Description |
| 1 | Earthing with 50mm dia Galvanised iron pipe 3.64mm thick x3.04 mts long and 1x4SWG GI wire (1Mts long) 13mmx80mmdiaGI bolts, double nuts, double washers incl. S&F 15mm dia GI pipe protection (1mtr. Long ) to be filled with bitumen as to GS.for softsoil ISI Medium GI Pipe |
| 2 | Supply of Single Steel Tubular pole of 8mtr long including base platewith Stiffener having following secification includingtransportation etc. 410-SP-15, 8mtr long, wt-119kg Stiffner 150x150x5mmx6Nos Base Plate 350x350x10mm |
| 3 | Earth work in excavation of foundation trenches or drain in allsortsof soils (including mixed soil but excluding laterite or sand stone) including removing spreading ro stacking the spoils within a lead of75 m, as directed including trimming the side of trenches, levelling dressing an raming the bottom, bailing out water etc. as required complete. |
| 4 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes including shuttering etc as required. |
| 5 | Reinforcement for reinforced concrete work in all sorts of structure including distribution bars, stirrups, binders etc. initial straightening and removal of loose rust (if necessary) cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16G black annealed wire at every intersction, complete as per drawing and direction |
| 6 | Holding down bolt with nut including 100 x 100 x 6 mm plate washer at bottom fitted complete and packing the hole with cement concrete or cement grout as directed. 20mm dia 600mm long |
| 7 | Plaster (to wall, floor, ceiling etc) with sand -cement-morterincluding rounding off and chamfering corners as directedand racking out joints including throating, noising and drip course, scaffolding / staging where necessary ( Ground floor) (excluding cost of chipping over concrete surface ) |
| 8 | Errection of Single ST pole of 8mtr long over the existing RCCfoundation including necessary arrangement etc as required. |
| 9 | Supply & Fixing carring of header/structure for fixing of 6 nos Flood Light made of 6x65mm Dia 500mm long CHS pipe and MS angle frame 40x40x6mm structure tip portion is cover with 750x750x3mm thick top plate welded with angle frame structure 4 nos angle frame each 300mm long. The header is also extra supported by 4nos vertical angle of above specification including providing of 6nos hole for locking/checknut device with the frame size) 300x300 mm to the top & ST pole for fixing 6nos Flood. the complete header is also strengthening with design MS flat size 500mm 6mm thick including scoffloling arrangemetn for lifting the same at the top of 12mtr longST pole as per diretion of EIC including painting. |
| 10 | Painting of Steel Tubular Pole of lengths and no. of coats of paint, as given below with ready mixed paint/primer of approved make, and brand incl. preparation of surface by sand paper/emery paper, cleaning etc. for receiving fresh coat of paint. a) Upto 9.0 mtr. long pole, i.One coat of red lead/Zinc chromate priming |
| 11 | ii.1st coat of synthetic enamel paint over the primer |
| 12 | iii.2nd coat of synthetic enamel paint over the 1st coat |
| 13 | Supply of 26W (including all losses) All in One Solar LED Street Lighting System with minimum system lumen output of4500lumens, 12V 60Watt Peak PV Module, >380 Wh Lithium Ferro Phosphate (LiFePo4) battery, Integrated MPPT charger with driver and efficiency of both Charger & driver is of >90%. The luminaireshall have a rated system lifetime of 50,000 burninghoursat L70 and CCT of 5700 K. It has Pressure Die Cast aluminiumhousingwith UV stabilized Polycarbonate front cover. The luminaireshall have CRI of > 70 and Protection of IP 65. It has in-builtmotion sensor and LED indicator for Charging and discharging of battery. The luminaire provides 2 days battery backup with factory setting dimming profile & PIR sensor. It has Horizontal & Vertical Pole Mounting options and Tilt angle can be adjustable in between 0 - 15 degree. LM 79 report and Type Test Certificate to be submitted for luminaire, LM 80 report for LED source issued by LED manufacturer and Test reports of Solar PV module, Battery and Charge Controller. Similar to Philips Make Sunstay “BRP710 LED45 CW MR S1 12V LFP Solar IN”. |
| 14 | Add GST @18% |
| 15 | Add labour welfare cess @1% |
AI Tender Summary
Tender Timeline
Dec 29, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedJan 16, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJan 19, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender