Tender For Resurfacing Of East Coast Road At Nemmeli At Ch 41.400 To 44.400 On Rhs - 3.00 Kms, Chengalpattu-Tamil Nadu

Tender For Resurfacing Of East Coast Road At Nemmeli At Ch 41.400 To 44.400 On Rhs - 3.00 Kms; 1 Providing And Laying Tack Coat Over Existing Bt Surface Using 2 Kg Of Bitumen Emulsion ( Rs1 ) Per 10 Sqm For Preparatory To Another Bituminous Construction Over It Including Cost Of Material, Labour Charges, Rentals For Machinery, Fuel And All Other Incidental Charges Etc., Complete As Per Clause 503 Of Morth 2 Providing And Laying Bituminous Concrete To 40 Mm Thick As Per Design Mix Usingvg30 Bitumen For Premixing Including Cost And Conveyance Of All Materials To Cmp Site, Heating The Bitumen And Aggregate To Required Temperature And Mixing Them In Required Temperature In Central Hot Mix Plant 20-30 Ton Capacity, Conveying The Mix By Tipper Trucks To Paver Site, Spreading The Mix To Uniform Thickness Of 40Mm With Mechanical Paver To The Specified Grades And Cross Sections And Consolidated By 8-10 Tonne Vibratory / Pneumatic Roller To The Required Density Etc., Including Labour For Attending To Paver To Site Etc. Including Hire Charges And Fuel Charges For 20-30 T Cmp With Bitumen Boiler, Tipper Trucks, Paver Finisher, Vibratory / Pneumatic Roller And All Other Tools And Plant Required, Includingall Other Incidental Charges Etc., Complete As Per Specification Using Cmp As Per Clause 507 Of Morth 3 Providing And Laying Of Hot Applied Thermoplastic Compound 2.5 Mm Thick Including Reflecting Glass Beads @ 250 Gms Per Sqm Area, Thickness Is Exclusive Of Surface Applied Glass Beads As Per Irc:35. The Finished Surface To Be Level, Uniform And Free From Streaks And Holes, With All Lifts And Leads Etccomplete As Per Mort &H Technical Specification Clause No.803 4 Providing And Fixing Reflective Road Studs Of Category A Raised Pavement Markers Made Out Of Poly Carbonate / Methyl Methercrylate / Abs Moulded Body Confirming To Astm D 788 Andreflective Panels With Micro Prismatic Lens Capable Of Providing Total Internal Reflection Of The Light Entering The Lens Face With Retro-Reflectance And Chromaticity Values Conforming To Astm D4280. The Reflective Raised Pavement Markers Shall Also Confirm To The Morth Circular No Rw / Nh. 33023 / 10 / 97- Do.Iii Dt 11.06.97 . The Height, Width And Length Shall Notbe Less Than 15Mm, 90Mm And 100 Mm And With Minimum Reflective Area Of 13 Sq.Cm On Each Side And The Slope To The Base Shall Be 35+ / 5 Degree. Each Reflector Shall Have A Cil Not Less Then Values Specified In Table 2 Of Said Mort&H Circular. The Strength Of Detachment Of Integrated Cylindrical Shanks, ( Of Diameter Not Less Than 19+ / -2Mm And Height Not Less Than 30+ / -2Mm ) From The Body Is To Be A Minimum Value Of 500Kg F. Fixing Will Be By Drilling Holes On The Road For The Shanks To Go Inside, Without Nails And Using Epoxy Resin Based Adhesive As Per Manufacturers Recommendation And Complete As Directed By The Engineer. The Marker Shall Support A Load Of 13635 Kg Tested In Accordance With Astm D4280 And Confirming To Irc 35-2015 Guidelines And Mort&H Specification 804 Etc., Complete 5 Painting Old Cc Surface With Two Coats Of Synthetic Enamel Paintof Approved Quality And Colour Including Thorough Scraping, Clean Removal Of Dirt Etc Complete Complying With Standard Specifications Of Clause 800 Of Morth And As Directed By The Engineers Incharge

INR 17700 /-

INR 170200.0 /-

Refer document