Tender For Construction Of Auditorium Cum Conference Hall At Changlang.
Tender Value
8 Crore
Estimated cost
Bid Submission
10 Jan 2024
0 days left
EMD
8 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
changlang → Arunachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Auditorium Cum Conference Hall At Changlang.
BOQ
| Sl. No. | Item Description |
| 1 | Site Development |
| 2 | Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 3 | Building Works |
| 4 | Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 5 | Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centringan shuttering in:a) Foundations and plinth |
| 6 | Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 7 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 8 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) ofthickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.a) M20 (1 cement : 1.5 coarse sand : 3 stoneaggregate 20 mm nominal size). |
| 9 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20mm nominal size). |
| 10 | Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete. |
| 11 | b) Suspended floors, roofs, landings shelves andtheir supports, balconies and chajjas (3.5 m height). |
| 12 | c) Lintels, beams, girders, bressumers and cantilevers etc. |
| 13 | d) Column, pillars, posts and struts etc. |
| 14 | Reinforcement of RCC work including bending, binding and placing in position complete. b) Tar/TMT steel |
| 15 | Brick work with best available local bricks in foundation and plinth in cement mortar 1:3 (1 cement : 3 fine sand). |
| 16 | Half brick masonry (with best available local bricks) in cement mortar 1:3 (1 cement : 3 coarse sand) in foundation and plinth. |
| 17 | 12 mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
| 18 | Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete. |
| 19 | Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. b) 50 mm thick |
| 20 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete [both side of Internal Wall and inner side of External wall ] |
| 21 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. (a) Two Coat [both side of Internal Wall andinner side of External wall ] |
| 22 | Providing and fixing factory made uPVC white colour sliding glazed window ( two or three track as detailed in 8.1(a) and 8.1(b)) upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thickgalvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile),appropriate dimension of uPVC extruded glazing beads and uPVCextrudedinterlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rodof required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.(Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (a)Two track two panels sliding window made of (big series) frame 67x 50 mm &sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/dobule glazing bead of appropriate dimension. (Area of window above 1.75 sqm upto 2.50 sqm) |
| 23 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick: Float Glass Panes-4mm thick glass panes of weight not less than 10kg/sqm |
| 24 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.(a)Fixed to steel windows by welding(outside the Window Frame) |
| 25 | Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer\"s specification and direction of Engineer-in-charge. |
| 26 | 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer\"s specification and direction of Engineer-in-charge. Non Decorative finish (matt finish) |
| 27 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : (a) 300x10 mm |
| 28 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : (a)125mm |
| 29 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. (a)Single rubber stopper |
| 30 | Providing and fixing bright finished brass 100 mm mortice latch andlock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. |
| 31 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete b) Size of Tile 600x600 mm |
| 32 | Providing and fixing white vitreous china type water closet pedestal (European type WC pan) with seat and lid CP brass hinges and rubber buffers, 12.5 Litres high level CI flushing cistern with fittings RS or CI brackets, galvanized steel telescopic flush pipe with fittings and clamps, 20 GI overflow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting making good the walls and floors where required. a) WC pan with white plastic seat and lid. |
| 33 | Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required. a) Long Pan patten WC Pan |
| 34 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and340x430x265 mm sizes respectively with CI automatic flushing cistern with fittings, RS or CI brackets standard size galvanized steel flush pipe and spreaders with brass unions and GI clamps complete including painting of cistern and fittings, cutting and making good the walls and floors where required. d)Range of four urinals with 15 Litre CI automatic flushing cistern |
| 35 | Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, includingcutting and making good the walls where required. |
| 36 | Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth. |
| 37 | Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete. |
| 38 | Providing and fixing Durashine zinc-Aluminium alloy coated (TATABluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses. Details of cost for 179.655 Sq.m.Laying and fixing 20 sheets in 3 row require Overall Sheet area of 20 x 3 x 3.05 x 1.072 plus 3% wastages = 202.061 Sqm After H & L laping as per manufacturer\"s specification, effective Area Measurable will be 20 x 3x 2.95 x 1.015 = 179.655 Sqm |
| 39 | Providing and fixing Durashine zinc-Aluminium alloy coated (TATABluescope building product) sheet ridges fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses.Details of cost for 11.75m Laying and fixing 4 lenths of 3.05m each require Overall length of 4 x 3.05 plus 3% wastages = 12.566m After laping as per manufacturer\"s specification, effective Measurable length will be (4 x 3.05) - (3 x 0.15) = 11.75m |
| 40 | Furniture & Furnishing |
| 41 | i) Auditorium ChairTip Up Pushback Mounted Chair each eachSpecifications :# M.S. metal structure.# 3 mm Foam laminated fabric.# Moulded PU foam above 48 density.# PPCP handle with cup holder.# Sliding Pushback mechanism.# PPCP tray cover for Seat & Back.# Seat numbering for seat & back both.# Row numbering.# Black powder coating surface.# Auto tip up feature.Make: Featherlite |
| 42 | ii) CARPET Loop pile graphic woven polypropelene carpet. per sqm per sqm 100 % bcf olefin. Pile height 4mm amd 675 gms per sqmtr pile weight. Roll width 4 mtr |
| 43 | iii) Providing and fixing in position Wall Quilting upto specified height as per design and engineer in charge |
| 44 | Video Projection System |
| 45 | Sony- VPL-PHZ61Projector 7000 lm WUXGA, Laser, 20,000 hrs, 8:1 Contrast, 4K 30Pinput |
| 46 | Prima/VariousProjector Stand/mout kit |
| 47 | Prima/Various164\" ( 16:10 ) , tab tension motorized Projector screen (W 3.5 x H 2.2 meter) |
| 48 | Prima/VariousLVC system for 3rd party automation control. |
| 49 | Switching and Control System |
| 50 | Atlona- AT-HDR-H2H-44MA 4K HDR 4×4 HDMI Matrix Switcher |
| 51 | Atlona- AT-HDR-EX-70C-KIT 4K HDR HDMI Over HDBaseT TX/RX with Control and PoE |
| 52 | Atlona- AT-OME-EX-WP-KIT Wallplate HDBaseT TX/RX for HDMI with USB |
| 53 | CRESTRON CP4 4-Series™ Control System |
| 54 | CRESTRON- DIN-DALI-2DIN Rail 2-Channel DALI® Interface |
| 55 | Apple- ipadApple 10.9\"\" ipad wi-fi 64 GB for Audio Video control |
| 56 | Digital Podium and Wireless Presentation System |
| 57 | Novo- NCX 300Wireless Presentation System |
| 58 | VariousDigital Podium- 22\" Touch Monitor, 60W Amp, 2x Speakers, 1x Gooseneck Mic, 1x Wireless Hand& Collar Mic Doc Cam, PC i3/4GB/500GB, Wireless K&M Button controller & Button hydraulic |
| 59 | Sound Reinforcement System |
| 60 | QSC- K12.22000W Active portable loudspeaker system; 12-inch woofer; 1.0-inch compression driver; 75 degree conical waveguide; dual angle pole socket; presets and user adjustable DSP |
| 61 | QSC- CP121000W Active portable loudspeaker system; 12-inch woofer; 1.0-inch compression driver; 75 degree conical waveguide; pole socket; selectable user contours. For use as main or stage monitor. |
| 62 | QSC- KS1122000W Active, Ultra-Compact subwoofer; 12-inch woofer; 4 large, swivel casters; dual M20 threaded pole socke |
| 63 | QSC- Core 110FUnified Core with 24 local audio I/O channels, 128x128 total network I/O channels with 8x8 Software-based Dante license included, USB AV bridging, dual LAN ports, POTS and VoIP telephony, 16x16 GPIO, 16 next-generation AEC processors. |
| 64 | Soundcraft- Signature 12 MTK12 Ch Analog Mixing Console |
| 65 | Sennheiser- EW 100 G4 835Wireless Handheld Microphone System (Transmission Range: up to 100 meters / 300 feet) |
| 66 | Sennheiser- EW100 G4 ME2 Wireless Lavalier Microphone System (Transmission Range: up to 100 meters /300 feet) |
| 67 | CustomWall mount bracket for speakers, |
| 68 | CustomMicrophone 2way box for stage mounting |
| 69 | Various16 port Managable POE Network Switch |
| 70 | Custom27U Equipment rack |
| 71 | RHYTHM- FRTTransportation/Fright Charges (As per Actual) |
| 72 | RHYTHM- CABLEAudio Visuasl cable and Accessories (HDMI, LAN, Power, Video, Speaker and Mic, Control Cable. |
| 73 | RHYTHM- INSTInstallation, Testing & Commissioning. |
| 74 | RHYTHM- PRGAV Programming |
| 75 | SH:- Stage Lighting |
| 76 | CE Certified Fresnel spot light with minimum following Technical specifications • Light Source : Single LED COB Source • Color Temerature : 3200K • CRI & TLCI : > 95 • Beam Angle : 9° - 52° manual Zoom • Focusing mechanism of lights should be SS/Brass lead screw type for step less smooth zooming. Sliding type focusing mechanism shall not be acceptable. • Fresnel Lens Dia should not lesser than 200mm • Zooming function of Fresnel should be through pole operated yoke (POS). • Lux output at 2 Mtr : > 38,500 Lux @ 9° &> 2,100 Lux @ 52° • Power supply Driver : IP65 or higher grade with pf >0.96 @ 230V • Flickering Rate : more than 20000 FPS • Accessory slot for Gel frame and Gel Filter Frame should be available or else fixture will be rejected. • Control Protocol : DMX & Manual • Fully RDM Compliant in DMX Mode • Manual Control via Touch pad. Tactile Switch for manual control fixture will be rejected.Make - Canara LightingModel - CAN LED T1 |
| 77 | CE Certified LED PARCAN Light with latest RDM technology for user friendly operation with below specifications: • Light Source : Single COB LED Source• Power Factor : >0.95 @ 230V AC 50Hz• Color Temperature : 3200K with CRI & TLCI Value > 90• Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 1/2 DMX-512 Channel Modes• Beam angle: 9°/15°/20°/25°/30° Manually Selectable • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run• Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project.• LUX @ 2m: > 40,000 @ 9° Beam Angle• Flickering Rate : more than 10000 FPS • Dimming: 0 - 100% Electronic Dimming• Function: Strobe, Dimming• Housing : Spun Aluminium Housing with black epoxy polyster powder coated finish.• Accessory slot for Gel frame and Barndoor should be available or else fixture will be rejected.• Power and DMX: Loop in and loop out compulsary• DMX in & Out Through : 5 Pin XLR connectors• Certification: CE / BIS Make - Canara Lighting Model - CAN LED PARCAN 100 |
| 78 | CE Certified LED PAR Light with latest RDM technology for user friendly operation with below specifications: • Base Color 3200K Color Mixing• LED Configuration : Multiple Nos Individual 3200K LED Configuartion• Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 1 DMX-512 • Beam angle: 15° • Control mode: RDM, DMX512 & Manual• Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project.• LUX @ 2m: >7,500 @ 15° Beam Angle• Dimming: 0 - 100% Electronic Dimming• Function: strobe, dimming, sound active and Master slave.• Housing: Die Casted Aluminium or Metal Housing with black epoxy polyster powder coated finish.• Accessory slot for Gel frame and Barndoor should be available or else fixture will be rejected.• Power and DMX: Loop in and loop out compulsary• DMX in & Out Through : 5 Pin XLR connectors• Certification: CE / BIS Make - Canara Lighting Model - CAN LED PAR 543 T |
| 79 | CE Certified LED PAR Light with latest RDM technology for user friendly operation with below specifications: • Base Color RGBW Color Mixing• LED Configuration : Multiple Nos Individual RGBW LED Configuartion• Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 8 DMX-512 • Beam angle: 15° • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run, Sound Active• Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project.• LUX @ 2m: >10,500 @ 15° Beam Angle• Dimming: 0 - 100% Electronic Dimming• Function: strobe, dimming, sound active and Master slave.• Housing: Die Casted Aluminium or Metal Housing with black epoxy polyster powder coated finish.• Accessory slot for Gel frame and Barndoor should be available or else fixture will be rejected.• Power and DMX: Loop in and loop out compulsary• DMX in & Out Through : 5 Pin XLR connectors• Certification: CE / BISMake - Canara LightingModel - CAN LED PAR 543 |
| 80 | CE Certified LED Profile Spot Light with latest RDM technology for user friendly operation with below specifications: • Light Source : Single LED COB Source• Power Factor : >0.95 @ 230V AC 50Hz• Color Temerature : 3200K, CRI & TLCI Value > 95• R9 Value > 94• Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 1/2/3 DMX-512 Channel Modes• Beam Angle : 19° or 15°• Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run• Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project.• Lux output at 2 Mtr : > 27,500 Lux@ 19° or 15°• Flickering Rate : more than 10000 FPS • Dimming: 0 - 100% Electronic Dimming• 4 Beam shaping shutters• Accessory slot for Gobo and gobo holder, Iris & Color Frame should be available or else fixture will be rejected.• Housing: Metal Housing with black epoxy polyster powder coated finish or PVC Body with matt black finish• Power and DMX: Loop in and loop out compulsary• DMX in & Out Through : 5 Pin XLR connectors• Certification: CE / BISMake - Canara LightingModel - CAN LED PRO 319 |
| 81 | CE Certified LED Blinder Effect Light with latest RDM technology for user friendly operation with below specifications: • Light Source : Quad LED COB Source• Power Factor : >0.95 @ 230V AC 50Hz• Color Temerature : 3200K, CRI & TLCI Value > 95• R9 Value > 94• Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 4/8 DMX-512 Channel Modes• Beam Angle : 40°• Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run• Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project.• Lux output at 2 Mtr : > 8,000 Lux@ 40°• Flickering Rate : more than 10000 FPS • Dimming: 0 - 100% Electronic Dimming• Power and DMX: Loop in and loop out compulsary• DMX in & Out Through : 5 Pin XLR connectors• Certification: CE / BISMake - Canara LightingModel - CAN LED BLDR 400 |
| 82 | CE Certified LED RGBW Cyclorama Wash Light with RDM protocol and Laser cut aluminium body duly epoxy polyester powder coated in black matt texture finish with following specifications -• LED : 480x0.5W RGBW LED (120R + 120G + 120B+ 120W) Nichia or Lumiled Make LED • Beam Angle : 96°• Detachable Assymmetric reflector with 64°, 62° for uniform wash. • Light Out put : 3000 Lux at 1 Mtrs without assymmetric reflector. • User Interface : 4 Nos High Precision Tactile type selector switch with Seven Segment Display • Fully RDM Compliant when in DMX mode • Dimming : 0 to 100% 8 Bit Linear Dimming • DMX data IN / OUT: 5 pin locking XLR • Natural Cooling System. No fan, No noise.• 2.5 m Power In + 0.5 m Power out or 3 Mtr 3 core 1 mm² FRLS & ISI mark cable with 3pin IEC Male Plug • 3 mtr DMX loop cable with cable mount 5 pin locking XLR • CE Certificate should be enclosed to ensure the required quality and safety of the products.Make - Canara LightingModel - CAN LED CYC 150 |
| 83 | 4 - leaf barndoor with scrims for 200W LED fresnel spot light,undergone through 7 Tank chemical treatement to keep them rust free and, duly powder coated in black matt texture finish.Make - Canara LightingModel - CAN LED 200BD |
| 84 | Die cast Aluminium C - Clamp with safety chain duly epoxy polyester powder coated in black matt texture finish and safe working load of 100kg with below specifications.• Lock - MS threaded Galvanized lock key, • Plastic Glass filled nylon moulded M6 key. • Receptacle - 28mm standard TV spigot. • Safety - MS Galvanized chain with pin. • Finish - Pretreated and black epoxy polyester powder coated. • Self-weight - 0.54Kg Make - Canara LightingModel - ACC-10 |
| 85 | Safety bond with lock clip 1.5 Mtr Long made with twisted pair of GI wire rope, 2mm or 3mm Thickness with sleeve to be fixed around the grid to avoid fall of the material in case if the \"C\" clamp is not locked properly. SWL 150Kgs.Make - Canara LightingModel - SB-15 |
| 86 | 79mm Round Identification name plate duly epoxy polyester powder coated in matt texture finish.Make - Canara LightingModel - INP-79 |
| 87 | Fixed Stage Light Bar, length 12 Mtrs made using MS 40NB Class ‘B’ Pipe dual barrel construction arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications:• Dual barrel Light bar equipped with 40x75x40 Cable trenching arrangement with lid for better aesthetic look and cable safety. • Dual barrel pipe construction welded with 75x6mm MS Flat in every 1 Mtr for better strength • With Suitable Suspenders to fix the light bar with every 2mtr pitch.Make - Canara LightingModel - FLB-14M |
| 88 | Fixed FOH Light Bar, length 16 Mtrs made using MS 40NB Class ‘B’ Pipe dual barrel construction arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications:• Dual barrel Light bar equipped with 40x75x40 Cable trenching arrangement with lid for better aesthetic look and cable safety. • Dual barrel pipe construction welded with 75x6mm MS Flat in every 1 Mtr for better strength • With Suitable Suspenders to fix the light bar with every 2mtr pitch.Make - Canara LightingModel - FLB-16M |
| 89 | Main Curtain track system 16 Mtrs long, center parting with overlap of 0.9mtr arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications: • Heavy duty curtain track duly epoxy polyester powder coated in black matt texture finish. • 1.0 HP Motor, 3 Phase Motor. • GI wire ropes with steel core at center. • Curtain holding trolliesplaced uniformly at specific interval of 200mm /250 mm throughout the track. • Diverter pulley • MS yellow passivized Routing pulleys with ball bearing for smoother noiseless movement 165mm for outer diameter, 145mm diameter at groove base with 12mm pulley thickness. • All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish. Make - Canara LightingModel - MCT-23M |
| 90 | Main Valance Bar, length 16 Mtrs made using 40NB, 48mm OD construction arrangement 2mm Thickness undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with suitable suspenders.Make - Canara LightingModel - FVB-16M |
| 91 | Frill Bar, length 12 Mtrs made using 40NB, 48mm OD construction arrangement 2mm Thickness undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with suitable suspenders.Make - Canara LightingModel - FFB-15M |
| 92 | MS, Wing frame made out of 25X25mm or higher size made of MS square pipe with 2mm in thickness undergone through various chemical treatment to keep them rust free and duly powder coated in black matt texture finish with Below Specifications:• Wing Frame Size4.5 x 1.5 Mtr • 1.5meter wing track of 48x84mm with grid mount brackets made of40X50X40mm C track,• Pivotable 4 wheeled suspension trolley,• Adjustable floor locking screw jacks with rubber grips, • Inverted 4-Wheeler Trolley with Flexi Adaptor Clamp, • Heavy duty wing track to be laid for minimum length of 1.5mtr, along the width of the stage. • 360° Rotatable and can move in unidirectional • All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish.Make - Canara LightingModel - WF-1302M |
| 93 | Cyclorama frame arrangement of size 10 Mtr x 4 Mtr undergone through various chemical treatmentto keep them rust free and duly powder coated in black matt texture finish with Below Specifications:• Heavy duty Cyclorama 10 Mtr Length duly epoxy polyester powder coated inblack matt texture finish to use as straight cyclorama track• MS fabricated Grid/wall mount bracket constructed of C track of dimension 40X50X40mm duly powder coated to hold the Cyclorama track,• MS fabricated Tie down railing cut length 3 mtr duly powder coated to keep the cyclorama in drumtight arrangement,• 2 wheeler trolley placed uniformly at specific interval of 200mm/250mm throughout the track to hold the cyclorama screen• MS powder coated Leading edge pipe of 25NB, 33.4MM OD, 2mm thickness to keep the cycloramain drum tight arrangement.• All the MS materials under gone through 7 tank process with various chemical treatment to keepthem rust free with and duly epoxy polyester powder coated in black matt texture finish.Make - Canara LightingModel - CF-1004M |
| 94 | MS Side Lighting Ladder of suitable length and Width (Min 2400 mm Height & 600 mm Width)• Made using 40NB, 48MM OD, 2mm thickness MS Pipe • Suitable suspender and clamps made with MS Angle of size 40x40x5 mm thick or higher size• Inverted 4-Wheeler Trolley with Flexi Adaptor Clamp, • Heavy duty Ladder Track to be laid throughout the depth of the stage.• 360° Rotatable and can move in unidirectional• All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish.Make - Canara LightingModel - FSL-2406M |
| 95 | MS Fabricated 4 way 10A, 250V A.C, IEC, Lighting Junction box made up of 22SWG CRCA for LED lighting fixtures with Pipe clamp arrangement for fixing on pipe grid or Raul plug arrangement for wall/floor fixing, duly black epoxy polyester powder coated texture finish.Make - Canara LightingModel - JB-410IEC |
| 96 | MS Fabricated 2 way 10A, 250V A.C, IEC,Junction box made up of 22SWG CRCA with rocker switch to power up splitter and console with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, duly black epoxy polyester powder coated texture finish.Make - Canara LightingModel - PSB-210IEC |
| 97 | MS Fabricated 5 pin DMX Signal IN Junction box fitted with 5 pin DMX Male socket, junction boxmade up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish.Make - Canara LightingModel - DMX-IBM5 |
| 98 | MS Fabricated 5 pin DMX Signal OUT Junction box fitted with 5 pin DMX female socket, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish.Make - Canara LightingModel - DMX-OBF5 |
| 99 | MS Fabricated 5 pin DMX Signal Loop Junction box fitted with 5 pin DMX male/female socket, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish.Make - Canara LightingModel -DMX-OBF5 |
| 100 | Well designed 27 Way Direct Lighting Distribution Board made up of CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt texture finish consists of R, Y, B Indicator lamp, 50A TPN incomer, SP Mcb\"s and for the junction boxes fixed on the top of the light bar including wiring and busbar connection with proper earthing and Hingable door with magnetic door lock complete. Make - Canara LightingModel - DLDB-27 |
| 101 | Auxiliary marshalling box for power and signal cable termination in grid level and in Motorised Light bar• CE Marked FC/PG cable entry gland required Nos as per cable entry.• MS channel arranging to fix terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap. • Grey terminal connector with each line having P, N, E Indication for each line incoming and out going cable connectors.• Box door must be made with Hingeable door with screw lock. • Made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish.Make - Canara LightingModel - AMB |
| 102 | Motor Cable Termination box for power cable termination at grid level.• CE certified FC/PG 11 & 13.5 cable entry gland required Nos as per cable entry.• MS channel arranging to fix grey terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap. • Grey terminal connector with each line having L1, L2, L3, E, 6 , 2 , 4 Indication for each line incoming and outgoing cable connectors (L1, L2, L3, E for Power supply & 6 , 2 , 4 for Limit Switch connection)• Box door must be made with Hingeable door with screw lock. • Grid mount fixing arrangement for fixing on grid or Anchor fastener for wall/floor fixing• MS Boxe made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish.Make - Canara LightingModel - PJB |
| 103 | MS Fabricated Combined 5 Way Motor Control Center panel cum Remote Controlpanel for Light bars & Curtain system made up of 14SWG / 16SWG / 18 SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt seaman’s grey texture finish with following specifications.• 16A TP or TPN Incomer.• Main Contactor of 9A 240V 4 pole contactor with 04 -06A Over Load relay for safety• 24V 4 pole Low Voltage Contactors• 240V / 24 V Step-down transformer for Low voltage Contactors • All the FRLS PVC ISI Marking cables inside the panel routed through PVC gray color cable trough. • Red Color Mushroom head push button for emergency stop • Yellow color reset push button • Master sector actuator switch with 3 Position UP, DOWN & OFF • Spring return selector switchfor each hoist with UP & DOWN indication. • All the cables inside the panel routed through PVC gray color cable trough. • Panel Including wiring with proper earthing. Make - Canara LightingModel - MCCP/RCP-5 |
| 104 | RDM Compatible DMX Splitter unit with Minimum following specifications.? 1 Nos 5 Pin DMX In socket and 8 Nos 5 Pin DMX Out socket? In and out signal Optically Isolated? Atleast 8 LED Indicator for check the signal flow in each output.?Suitable for standard 19” cabinet? Duly black epoxy polyester powder coated texture finish.Make - Canara LightingModel - CS-81 |
| 105 | Digital Lighting console with Minimum following specifications.? 512 Channel, 2 Output? No. Of Direct Fixture Control : Atleast 200 or more? No. Of Faders : Atleast 12 ? Atleast 4 Encoder Wheels? 7\" Touch screen display for navigation? Backlight Keyboard? Numeric Key BoardMake - Canara LightingModel - CANDX-C512 |
| 106 | 5 pin XLR male / female connectors of made up of Extra high temperature resistant insulator material, Larger solder contacts for easier termination.Make - Canara LightingModel - DMX5-CP |
| 107 | 5 Pin XLR Termination plug made up of extra high temperature resistant insulator material, Larger solder contacts for easier termination with 120 Ohm resister with 0.25Watt for signal termination.Make - Canara LightingModel - DMX5-TP |
| 108 | Main Valance Fabric : Fire retardant velvette fabric100% (2 times of the finished dimension) gathering as per the approved patern and colour, not less than 200 GSM, duly stitched along witheyelets. Size : L 16 x H 1.3 MTRMake - NexgenModel - Custom |
| 109 | Main Curtain Fabric : Fire retardant velvette fabric with lining 100% (2 times of the finished dimension) gathering as per the approved patern and colour, not less than 200 GSM, duly stitched along witheyelets. Size : L 16 x H 4.5 MTRMake - NexgenModel - Custom |
| 110 | Frill Fabric : Fire retardant cotton fabric 50% gathering as per the approved patern and colour, not less than 200 GSM, duly stitched along with eyelets. Size : L 12 x H 1.3 MTRMake - NexgenModel - Custom |
| 111 | Wing Fabric : Fire retardant cotton fabric 0% gathering for as per the approved patern and colour, not less than 200 GSM, duly stitched along with eyelets. Size : H 4 x W 4.1 MTRMake - NexgenModel - Custom |
| 112 | Perforated plastic Cyclorama screen with seam welded, off white, with eyelets along all four sides, perforated plastic screen with eyelets.Size : L 10 x H 4 MTRMake - Canara LightingModel - Custom |
| 113 | PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 7cx1.5 sq mm.Make - KEIModel - Custom |
| 114 | PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 4cx 4 sq mm.Make - KEIModel - Custom |
| 115 | PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 3cx1.5 sq mm.Make - KEIModel - Custom |
| 116 | FR Grade DMX Signal 4 core + Ground shieldingCable with CE mark for the Signal network.Make - Falcon / DeepcabModel - Custom |
| 117 | MS perforated tray of Size 40 x 75 x 40mm & 1.6 mm Thickness undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish along with clamping arrangement.Make - Canara LightingModel - PCTL-0752 |
| 118 | Internal earthing copper bare conductor of size 14 SWG for power network related to work coming under our scope.Make - CustomModel - Custom |
| 119 | Installation hardware’s such as clamps, connectors, glands, lugs, ferrules, welding rods and miscellaneous items required during installation work.Make - CustomModel - Custom |
| 120 | SH: B/wall- 3.00 Mt Ht,Length-44.73 Mtr |
| 121 | Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work I. Ordinary soil A). Manual Means (Depth upto 3 m) |
| 122 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 123 | Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specificationsB. PCC Grade M20(p). Height upto 5m |
| 124 | Centring and shuttering including strutting, propping etc and removal of formwork for :b) Walls (any thickness) including attached pilasters, buttresses,plinth and string courses etc. |
| 125 | Reinforcement of RCC work including bending, binding and placing in positioncomplete. b) Tar/TMT steel |
| 126 | SH: R/wall- 3.00 Mt Ht,Length-111.15 Mtr |
| 127 | Excavation for Structures (Earth work in excavation of foundation ofstructures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work. I. Ordinary soil A).Manual Means (Depth upto 3 m) |
| 128 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 129 | Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications B.PCC Grade M20(p).Height upto 5m |
| 130 | Centring and shuttering including strutting, propping etc and removal of formwork for :b) Walls (any thickness) including attached pilasters, buttresses,plinth and string courses etc. |
| 131 | Reinforcement of RCC work including bending, binding and placing in positioncomplete.b) Tar/TMT steel |
| 132 | SH:-Storm Water Drain- 150 Mtr |
| 133 | Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, intoplinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 134 | Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : a) Foundations and plinth |
| 135 | Reinforced cement concrete in retaining wall (any thickness) including attached pillasters, buttresses, plinth and string courses, fillets etc from top of foundation up to floor two level excluding cost of centring,shuttering and reinforcement in : a) M20 (1 cement : 1.5 Coarse Sand : 3 stone aggregate 20 mm nominal size). |
| 136 | Centring and shuttering including strutting, propping etc and removal of formwork for :b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 137 | SH:-Internal Footpath 100 Mtr |
| 138 | Excavation in Ordinary Rock with Dozer with lead upto 100 metres (Excavation for roadway in ordinary rock by deploying a dozer, 80 HP including cutting and pushing the cut earth to site of embankment upto a distance of 100 metres ( average lead 50 metres ), trimming bottom and side slopes in accordance with the requirements of lines, grades and cross sections.) |
| 139 | Preparation of sub grade (Preparation of sub grade by excavating earth to an average depth of 22.50 cm, dressing to camber and consolidating with road roller, making good theundulations etc. and disposal of surplus earth, lead upto 50 m.) |
| 140 | Consolidation of sub-grade with road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the sub grade |
| 141 | Plant Mix Method (Construction of granular sub base by provided close graded material,mixing in a mechanical mix plant at OMC,carriage of mixed material to work site,spreading in uniform layers with motor grade on prepared surface and compacting with vibratory power roller to achive the desire density complete as per clause 401)For Grading I Material |
| 142 | Providing and laying cement concrete 1 : 1.5 : 3 (1 cement : 1.50 coarsesand : 3 stone aggregate 20 mm nominal size) excluding the cost of centringand shuttering in :a) Foundations and plinth |
| 143 | SH:- Approach Road 47.57 Mtr |
| 144 | Excavation in Ordinary Rock with Dozer with lead upto 100 metres (Excavation for roadway in ordinary rock by deploying a dozer, 80 HP including cutting and pushing the cut earth to site of embankment upto a distance of 100 metres ( average lead 50 metres ), trimming bottom and side slopes in accordance with the requirements of lines, grades and crosssections.) |
| 145 | Preparation of sub grade (Preparation of sub grade by excavating earth to an average depth of 22.50 cm, dressing to camber and consolidating with road roller, making good theundulations etc. and disposal of surplus earth, lead upto 50 m.) |
| 146 | Consolidation of sub-grade with road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the sub grade |
| 147 | Plant Mix Method (Construction of granular sub base by provided close graded material,mixing in a mechanical mix plant at OMC,carriage of mixed material to work site,spreading in uniform layers with motor grade on prepared surface and compacting with vibratory power roller to achive the desire density complete as per clause 401)For Grading I Material |
| 148 | Cement Concrete Pavement Connstruction ofunreinforced ,dowel jointed,plain cement concrete pavement over a prepared subbase with 43 grade cement @400 Kg per cum,coarse and fine aggregate conforming toIS 383 maximum size of coarse aggregate not exceeding 25mm,mixed in a batching and mixing plant as per approved mix design,transported to site,laid with a fixedform or slip form paver,spread,compacted and finished in a continuous operation including provision of contraction,expansion,construction and longitudinal joints,joint filler,separation membren,sealant primer,joint sealant,debonding strip dowel bar,tie rod,admixtures as approved,curing compound,finishing to lines and grades as per drawing) |
AI Tender Summary
Tender Timeline
Dec 26, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedJan 10, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJan 11, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender