Military Engineer Services-MES has published Tender For Additional / Alternator / Improvement To Certain Living-In-Officers Accommodation At Af Stn Gwalior. Submission Date for this Tender is 30-01-2024. Mobile Generator Tenders in gwalior Madhya Pradesh. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 09-Jan-2024 | AMD1 | Date | 23-01-2024 |
| 2 | 12-Jan-2024 | AMD2 | BOQ | 23-01-2024 |
| 3 | 23-Jan-2024 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 30-01-2024 |
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) of any mix / grade inground floor and pavings not exceeding 15cm thickness (below or above ground level) including removal of debris out off the AF station premises / MOD land, etc complete all as specified and directed. |
| 2 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for including removal of debris out off the AF station premises / MOD land, etc complete all as specified and directed. |
| 3 | Material and Labour for 50 mm thick PCC 1:3:6 type C-2 (using 40mm graded stone agg) as in plinth protection, finished even and smooth using extra cementcomplete all as specified and directed. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 5 | Taking down cement plaster on brick or stone masonry, etc. including raking out joints, hacking for key and scrubbing down with water, etc complete all as specified and directed. |
| 6 | Demolition of brickwork built in cement mortar of any description complete all as specified and directed. |
| 7 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed. |
| 8 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exceeding 1.5Sqm but not exceeding 4Sqm each including builders hardware etc complete all as specified and directed. |
| 9 | Taking down chowkhats or frames with shutters not exceeding 1.5Sqm each (without taking off shutters from the frames) etc including builders hardware etc complete all as specified & directed. |
| 10 | Re-fixing of shutters in same opening of any description exc 1sqm but n exc 2sqm etc complete all as specified and directed. |
| 11 | Dismantling of water tank exc 250 but n exc 500 ltr complete all as specified and directed. |
| 12 | Dismantling of Asbestos cement sheet /PVC (corrugated, semi-corrugated, etc.) sheets as in roof coverings/ cladding and ridge of any type as in hangars complete all as specified and as directed. |
| 13 | Dismantling existing roof treatment including tarfelt/cement plaster, etc from roof surfaces including cleaning the surface and removing the debris from site out of MoD land complete all as specified and directed. |
| 14 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 15 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed. |
| 16 | M&L for pre-painted galvalume aluminium zinc coating GI based corrugatedsteel sheet 0.50 mm thick of any colour having tensile strength of 550MPa as in roof covering /ridge/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 17 | M&L for pre-painted galvalume aluminium zinc coating GI based Plainsteel sheet 0.50 mm thick of any colour having tensile strength of 550MPa as in roof covering /ridge/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 18 | S&F roof trusses (framed), trussed, purlins, rafter, framing (beam, tee, angle, channel or flat sections)distance pieces, cleatsincluding fabrication and fixing conforming toFe-410-W (Gde E-250) quality-A complete all as specified & directed. |
| 19 | Material and Labour for preparation of new steel Surfaces of any description, over 10cm in width or girth,and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 20 | Material and Labour for preparation of old painted steel surfaces of any description,over 10 cm width or girth and applying one coat of synthetic enamel paint (ordinary tint), complete all as specified and directed. |
| 21 | M&L for PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregate) in roof kerbs or mud stops, including finishing the surface with grinder to receive the acrylic based water proofing material as mentioned in item no 1.23 here in after, rounded or chamfered on edges etc complete all as specified and directed. |
| 22 | M&L for plain cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in coving on chajja, balcony or in roof Kerbs, benching, coping , bed plates for fixing hold fast bed block, kerb stone in sides of interlocking tiles, rounded or chamfered on edges and similar work including necessary formwork complete all as specified and directed. |
| 23 | M&L for Single component, weather resistant, liquid applied acrylic polymer based elastomeric water proof coating using elastomeric water proofing membrance for all types of exposed roof slabs (new and old), terraces (sloped and flat) water proof coating shall be UV rays resistant, solar reflective, etc complete all as specified in particular specifications. |
| 24 | M&L for rendering 5mm thick in cement mortar (1:3) on concrete surface of ceiling finished even and smooth without using extra cement complete all as specified & directed. Note:-(1) Cost of scaffolding for rendering is including in the quoted rate. |
| 25 | M&L for rendering 15 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surface, finished even and smooth without using extra cement complete all as specified and directed. Note:-(1) Cost of scaffolding for rendering is including inthe quoted rate. |
| 26 | M&L for rendering 10mm thick in cement mortar (1:4) on fair faces of brick work or concrete surface, finished even and smooth without using extra cement complete all as specified and directed. Note:-(1) Cost of scaffolding for rendering is including inthe quoted rate. |
| 27 | Material and Labour for rendering 15 mm thick in cement mortar (1:4) on fair faces of brickwork / external surface of masonry wall using liquid water proofing compound mixed at 3%by weight of cement, surface finished even and smooth without using extra cement completeall as specified and directed. (Note: (I) WPC will be measured and paid separately under respective item of BOQ) Note:-(II) Cost of scaffolding for rendering is including inthe quoted rate. (2) Rendering will be done in two layer, Ist layer will be 10-12 mm thick and 2nd layer will be 3-5 mm thick. |
| 28 | Supply only water proofing compound of approved make all as specified and directed. |
| 29 | M&L for Roof tiles Mangalore pattern interlocking at side joints over screed bed or bedding layer of mortar 20mm thick with cement mortar 1:4 for laying floor finish with & includingwater proofing compound as per manufacturing instructions etc complete all as specified and directed. Note: WPC will be measured & paid separately under respective item of BOQ, |
| 30 | M&L for 15 mm to 18 mm thick Baroda green marble slab of approved type / variety (table rubbed and pre mirror polished) in window cill, jambs, steps, and cooking platforms including pointing in coloured cement to match with shade of Baroda green marble slab including half moulding of Baroda green marble slab edges over & including 20mm thick screed bed in CM (1:4) for laying of Baroda green marble slab etc complete all as specified and as directed. |
| 31 | Material and Labour glazed colour ceramic digitally designed coloured tiles 450 x 300 x 7mm thick coloured wall highlighter on vertical surfaces such as skirting dados, etc., set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles including fixing with neat cement based approved chemical adhesive required for tiling as backing coat complete all as specified and as directed. Note : Material of adhesive will be supplied and measured separately. |
| 32 | M&L for non-skid rectified edges (joint free) digitally designed coloured ceramic floor tiles not less than 7-8 mm thick (Square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm, in floors etc set & jointed in neat cement slurry and pointed in coloured cement to match the shade of tilesover & including 15 mm thick screed bedding CM 1:4 complete all as specified & directed. |
| 33 | M&L for Vitrified coloured ceramic tiles, double charged 10 mm thick (Square/rectangular) area of each tile not exceeding 0.36 Sqm, in floors etc set & jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles in cement mortar (1:6) etc complete all as specified & directed. |
| 34 | M&L for screed bed / bedding layer 10mm thick in CM 1:4 for laying of floor finishes etc complete all as specified and directed. |
| 35 | M&L for screed bed / bedding layer 15mm thick in CM 1:6 for laying of floor finishes etc complete all as specified and directed. |
| 36 | S&F pressed steel frames of size 165mm x60mmfor doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed. |
| 37 | M&L for plain cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in coping on chajja, balcony or in roof Kerbs, benching, coping , bed plates for fixing hold fastbed block ,kerb stone in sides of interlocking tiles , rounded or chamfered on edges and similar work including necessary formwork complete all as specified and directed. |
| 38 | S&F Flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels commercial type on both side and both faces is covered with approved pattern with decorative coloured laminate type 1 of 0.9mm thick and all around side faces covered with 10 mm thick 1st class hardwood liping duly polished complete all as per specified and directed. |
| 39 | S&F Factory made wire mesh solid PVC door shutter 35mm thick solid panel PVC(style) consisting of frame made out of M.S tubes 19 gauge thickness and size 19 mm x19 mm for stiles and 15 mm x15mm for the top lock and bottom rails. M S frame shall have a coat of metal primer of approved make and manufacture 19 mm x 19 mmM S frame shall be covered with heat moulded (100% lead free) plain PVC "C" channel made from 5mm (+_)0.25% thick PVC sheet of density 600kg/cum manufactured by an ISO 9001-2015 certified company of size 35mm thickness 90mm width out of which 75mm shall be flat and 15 mm shall be bend in 90 degree angle on either side forming stiles as well as rails to inner side of door to hide wire mesh fixing steel screw and 5 mm thick 115 mm widePVC sheet out which 100 mm shall be flat and 15 mm shall be bend in 90 degree angle on inner side to formtopand bottom and lock rail and 130 mm widePVC sheet out which 100 mm shall be flat and 15 mm shall be bend in 90 degree on both side to form lock rail. An additional 5mm thick (+_0.25) PVC strip of 20mm width is to be stuck on the inner side of the C channelusing PVC solvent cement adhesive panel with a GI/SS wire mesh of 0.36 mm to be fitted inside area of stiles and rail. The wire mesh in top, bottom and locked rail is sealed with 15 mm X 15 mm tube with steel screw of 13 X 6 mm.10 mm (5mm X 2 Nos) thick PVC strip of 25 mm width Is to be struck and nail on both side of GI wire mesh interior at the top, bottom and locked rail 10 mm thick 10mm thick ,20 mm wide cross PVC sheet as gap insert for the top rail & bottom rail.Door to be fixed to frames with 3 nos.MS powder coated butt hinges of size 100mm x25mm x2mm using 32mm long steel screws drilled suitable to pass through both the walls of the M S tubeother hardware should be fixed with 19x6mm six steel screws complete all as specified and directed. |
| 40 | S& F Solid WPC door frame 100X 50 mm single rebate) factory made and 100 % lead free (Single extruded process) material with density 780 kg/Cbm & manufactured by an ISO 9001-2015 certify company all as per specification and drawing as directed by Engineer- in- charge. Note - The door frame should bewater proof, termite proof, fire retardant and having excellent screw holding capacity complete all as specified and directed. |
| 41 | S&F factory made 28mm thick solid WPC flush door shutter made from CO-EXTRUDED three layer rigid PVC foam sheet (Single extruded) with density no less than 600Kg/Cum outer layer 1 mm thick to be rigid UPVC with density not less than 1400 Kg /Cum and should be 100% Lead free door manufactured by an ISO : 9001: 2015 certified company. The door should be water proof, Termite proof, Fire Retardant and having good screw holding capacity and confirming as per IS 4020 complete all as specified and directed. |
| 42 | S&F powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium section weighing not less than 0.55 kg/m including necessary joining cleats glazing clips rubber packing anodised aluminium, snap beading screws, powder coated aluminium fittings such as peg stays 150mm long (1No.), 100mm long hinges type B-21 (2Nos) suitable handle(1No.) complete all as specified and directed. |
| 43 | S&F colour powder coated aluminium frame for doors windows, & ventilators with one or more rebates or aluminum section of two or more tracks incase sliding windows including jointing cleat for fixing (minimum thickness of powder coating shall be 50 micron) complete all as specified and diercted. Note :- (i)Colour of powder coating shall be approved by GE. (ii) wire mesh and sheet glass shall be measured and paid separately under respective items. (iii)Weight of only aluminium section used for fabrication of door/window shall be measured for payment) |
| 44 | Supply only beading for fixing of glass pane to aluminium window complete all specified and directed. |
| 45 | S&Ffor powder coated aluminium deco grills size4mmx4mm, 5.8mm thick and aperture not exceeding 80 mm width and including fixing with aluminium channel, 1 mm thick with steel screw and tint match with existing shade including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminum powder coated standard section around the opening complete all as specified & directed. |
| 46 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples etc complete all as specified & directed. |
| 47 | S&F 4.0 mm thick sheet glass, ordinary quality in square/ rectangular, not exceeding 0.5 Sqm in each pane complete all as specified & as directed. |
| 48 | S&F 4.0 mm thick figured glass pin headed type in squares/ rectangularnot exceeding 0.5 Sqm ineach pane complete etc complete all as specified & directed. |
| 49 | S&Fstainless steel handle125 mm size complete all as specified and directed. |
| 50 | S&F stainless steel handle75 mm size complete all as specified and directed. |
| 51 | S & F 100 mm longbutt hing stainless steel and fixedcomplete all as specified and directed. |
| 52 | S&F Stainless steelbarrel tower bolts of extruded section and fixed 150mm long complete all as specified and directed. |
| 53 | S&F aluminium, anodised barrel tower bolts of extruded section and fixed 100mm long complete all as specified and directed. |
| 54 | S & F 250mm long Stainless steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed. |
| 55 | S & F for mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete |
| 56 | S & F for Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring over all length of cover plate 150mmcomplete all as specified and directed. |
| 57 | Supply and fixing of rubber beading door seal 40x 5mm stripin bottom of door complete all as specified and directed. |
| 58 | M&L for providing and fixing stainless steel (ISI marked Grade 304) railing made of hollow tubes, channels, plates, etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts including fixing the railing with necessary accessories & stainless steel dash fasteners, etc., of required size, on the top of wall, floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 59 | Material and Labour for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, etc complete all as specified and directed. |
| 60 | All as per Srl item No. 1.59 abovebut 6mm to 8mm dia in stirrups, spacers and binders complete all as specified and directed. |
| 61 | M&L Formwork to soffits of suspended slabs such as roof slabs floor slabs, landing and similar work not exceeding 200mm thick (Horizontal or Sloping) .complete all as specified and directed. |
| 62 | M&L reinforced cement concrete (Nominal Mix) Type B-1 1:2:4(using20 mm gradedcrushedstoneaggregate)as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likecomplete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ. |
| 63 | Material and Labour for brickwork using old size sub class "B" brick, straight or curved on plan to any radius in half brick thick walls, built in CM (1:4) complete all as specified and directed |
| 64 | Material and Labour for brickwork using old size sub class -B brick straight or curved on plan exceeding 6m mean radius using old size brick built in CM (1:6) complete all as specified and directed |
| 65 | S&F rotational moulded polythene water storage tank of capacity 500 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mmbore GI medium grade over flow ( 450mm long) and washout pipe (600 mmlong ) with fittings including dismantling of existing tank and lowering down etc complete all as specified and directed. |
| 66 | S&F in repair 20 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) complete all as specified & as directed. |
| 67 | Taking up or down steel water tubing and connections of 15mm bore including cleaning for refixing or removal to store complete all as specified and as directed. |
| 68 | Taking up or down steel water tubing and connections of 20mm bore including cleaning for refixing or removal to store complete all as specified and as directed. |
| 69 | Taking up or down steel water tubing and connections of 25mm bore including cleaning for refixing or removal to store complete all as specified and as directed. |
| 70 | Refixing old20 mm bore GI tubes medium grade with all fitting and fixed complete to walls, ceilings or laid infloors in new or old position complete all as specified and directed. |
| 71 | Refixing old 25 mm bore GI tubes medium grade with all fitting and fixed complete to walls, ceilings or laid infloors in new or old position complete all as specified and directed. |
| 72 | Supply and fix 15 mm bore GI tubes medium grade with all fitting and fixed complete to walls, ceilings or laid infloors complete all as specified and directed. |
| 73 | Supply and fix 20 mm bore GI tubes medium grade with all fitting and fixed complete to walls, ceilings or laid infloors complete all as specified and directed. |
| 74 | Supply and fix 25 mm bore GI tubes medium grade with all fitting and fixed complete to walls, ceilings or laid infloors complete all as specified and directed. |
| 75 | S&F 20mm bore dia of pipe Stop valves/Gate valves cast copper alloy screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. complete all as specified and directed. |
| 76 | S&F 25mm bore dia of pipe Stop valves/Gate valves cast copper alloy screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. complete all as specified and directed. |
| 77 | S&F in repair vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat cover, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, etc., completeall as specified and directed. |
| 78 | Supply and fix in repairs PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including dual flush system valve float and handle, PVC flush pipe 32 mm bore and brackets complete set all as specified anddirected. |
| 79 | S & F in repairVitreous china wash basin , white , flat back, size 580 x 450 mm, excluding taps waste ,chain and plug and porcelain stopper but incluing brackets, waste pipe and PVC waste coupling and 15mm bore CP, brass mixer fancy type and cutting for and pinning in ends of brackets or errecting stand, complete all as specified and as directed. |
| 80 | S&F in repair concealed anglecockchromium plated with long shank & cup cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both end of size 15 mm bore complete all as specified and directed. |
| 81 | S&F in repair 15mm bore bib taps, two way cast copper alloyhalf turn valve handle, chromium platedfancy type complete all as specified and directed. |
| 82 | Supply and fix in repair PVC connections 15mm size with PTMT nuts of length 450 mm, complete all as specified and as directed. |
| 83 | S & F in repair brass chromium plated, tubular towel rails 20 mm dia, D- type, 60 cm long between flanges, complete all as specified and directed. |
| 84 | S&F in repair brass chromium plated hands health faucet with flxible pipe length not less than 1.00 mtr suitable for 15mm bore pipe complete all as specified and directed. |
| 85 | S&F in repairs brass chromium plated shower rose with swivel joints, 125 mm size in square with chromium plated long shank arm including fixing to steel pipe or union complete all as specified & as directed. |
| 86 | S&F cabinet mirror of size0.45m x 0.30m PVC with cabin as per trade pattern and approved by GE complete all as specified and directed. |
| 87 | S&F in repair brass Chromium Platedsoap dish complete all as specified and directed. |
| 88 | Material and Labour in repair for stainless steel grating doom with hole or without hole 100/125 mm dia size complete all as specified and directed. |
| 89 | S & F stainless steel sinks with drainage board, made out of 1.00 mm thick sheet for kitchen or laboratorywith plug, washers and waste pipe, cast iron cantilrver brackets, or bedding in cement mortar to dwarf walland connecting unionoverall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including 40mm dia PVC flexible pipe upto floor level of length not less 0.60 meter complete all as specified and directed. |
| 90 | S&F in repair PVC bends 100mm bore (any radius) diminishing piece or tapers larger measured) with solvent joint all as specified and directed |
| 91 | S&F in repair PVC bends 75mm bore (any radius) diminishing piece or tapers larger measured) with solvent joint all as specified and directed |
| 92 | S&F in repair 110mm bore PVC (SWR) floor trap including jointing to waste pipe fixed in cement concrete type B-I 1:2:4 (using 20mm graded crushed stone aggregate) complete all as specified and directed. |
| 93 | S&F in repair PVC (SWR) 75mm bore pipe branch piece single (equal or unequal) ordinary or inverted spigot and socket type or with parallel branches or ‘T’ piece with solvent joint complete all as specified. |
| 94 | S&F in repair 110 mm bore PVC (SWR) vent cowl complete all as specified and directed |
| 95 | S&F in repair 18mm thick solid PVC ply of 1st quality of one side prelaminated of approved colour and one side white colour fixed with screwes, solvent cement/ adhesive to make cup board shutters, including demolition of existing cup board shutter complete all as specified and directed. |
| 96 | S & F in repair18mm thickPVC boardof grade 1 quality of both side plain white colour fixed with screws, solvent cement/adhesive to make cup board sides top and bottom, shelves inside the cup board and shutter or drawerincluding demolition of existing board any type or specification complete all as specified and directed. |
| 97 | S & F continuous (Piano) hinges ,mild steel, bright finished or electrogalvanised, width of flap 30 mm (when open), complete all as specified and directed. |
| 98 | S&F 125 mm size alum, Hasp and staple, safety type, mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed. |
| 99 | M&L for machine cut kota stone slab flooring 18 mm to 25 mm thick of size not less than 575 mm X 575 mm over and including 75 to 100mm wide marble strip as motif laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing & polishing over & including 20 mm thick screed bed in CM (1:6) complete all as specified & directed. |
| 100 | M&L for machine cut kota stone slab in riser of steps (single piece), skirting 18 to 22 mm thick,laid and jointed with grey cement slurry pointed with coloured cement to match the shade of the slab including grinding rubbing & polishing over 10 mm thick backing coat in CM (1:4) etc complete all as specified & directed. |
| 101 | M&L for 18 to 20 mm thick machine cut pre polished kota stone slab in single piece in treads of steps including bull nosing & cutting two serrations on top set & jointed in neat cement slurry & pointed in coloured cement to match over & including 20 mm thick screed bed in CM (1:6) etc complete all as specified & directed |
| 102 | Dismantling of cast iron/reinforced concrete drain pipe of 75 mm/100 mm bore, jointed in cement mortar by taking out of trenches upto first manhole complete all as specified &directed. |
| 103 | S&F 100 mm bore cast iron spun soil, waste and vent pipein any length with or without ears with cement joints laid intrenches or in floors complete all as specified and directed. |
| 104 | S&F cast iron soil waste bends for 100 mm bore of pipe (any radius) duck`s foot or heel restcomplete all as specified and directed. |
| 105 | S&Fcast iron branch pieces of 75mm bore pipe, single (equal or un equal) ordinary or inverted (spigot or socket type) or with parallel branches with oval access doors complete all as specified and directed. |
| 106 | S &F 100 mm dia Cast iron cowlscomplete all as specified and directed. |
| 107 | S&F in repair stack clamps made out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roofs for 100 mm bore pipe etc complete all as specified anddirected. |
| 108 | S&F in repair 75mm bore PVC (SWR) pipe soil/ waste and vent pipes in any length with rubbering joints fixed to wall, laid under floor etc complete all as specified and as directed |
| 109 | S&F in repair 110mm bore PVC (SWR) pipe soil/ waste and vent pipes in any length with rubbering joints fixed to wall, laid under floor etc complete all as specified and as directed |
| 110 | S&F in repair 75 mm bore PVC (SWR) vent cowl complete all as specified and directed |
| 111 | S&F cast iron floor trap, for 75mm diameter of outletwith grating includingjointing to waste pipe fixed in cement concrete 1:2:4 type B-1 (using 20 mm graded stone agg)complete all as specified and directed. |
| 112 | S&F cast iron Nahani trap, for 100mm diameter of outletwith grating includingjointing to waste pipe fixed in cement concrete 1:2:4 type B-1 (using 20 mm graded stone agg)complete all as specified and directed. |
| 113 | S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cementcomplete all as specified and directed. |
| 114 | S&FCP, jet Spray including 1m long PVC/ Chromium plated flexible PVC pipe , necessary nut bolts and PVC washers fixed with PVC seat cover for pedestal pattern water closet, fixed in repairs,complete all as specified and directed. |
| 115 | M & L for PCC 1:5:10 type E-2( using 40 mm graded crushedstone aggregate) as infilling under sunken floor of toilet and bath room etc complete all as specified &directed. |
| 116 | M&L for suken portion in floor including demolition of existing traps and removing the material and cleaning with the wire brush to dry and apply one coat of URP and cement in ratio 1:1 @ 1 litre per Sqm . After the drying of this process apply two coats of pidifin 2K @ 1litre on each coat min 4 hours gap is required and 15mm thick. Rendering in cm 1:4 etc. complete including finished even and smooth without using extra cement all as directed. |
| 117 | S&F in repair fancy type decorated Stainless Steel curtain hanging rods 20 mm dia, and fixed to stainless steel bracket for hanging curtain complete all as specified and directed. |
| 118 | S&F Stainless Steel brackets having screw for tighting of curtain rod of 20mm dia for fixing of curtain rod, complete all as specified and directed. |
| 119 | S & F Stainless Steelbright color decorative corner/end cap for Curtain rod complete all as specified and directed. |
| 120 | S&F stainless steel peg set of six with base plate and fixed to wall/door with rawal pugs/ s/s screw all as specified and directed. |
| 121 | M&L for3mm thick cementitious wall careputty on new/old plasterfor internal wall surfaces complete all as specified and directed. |
| 122 | M&L for3mm thick cementitious wall careputty on new/old plasterfor exteriorwall surfaces complete all as specified and directed. |
| 123 | M&L for3mm thick cementitious wall careputty on new/ old plater for internalceiling wall surfacescomplete all as specified and directed. |
| 124 | M&L for preparing new plaster surfaces of ceiling and applying two coat distemperemulsion (OBD) with roller finish over a coat of cement wall primer (for same manufacturing of OBD)complete all as specified and directed. |
| 125 | M&L for complete removal of existing tratment on ceiling surface and applying two coat distemperemulsion (OBD) with roller finish over a coat of cement wall primer (for same manufacturing of OBD) complete all as specified and directed. |
| 126 | M&L for complete removal of existing treatment applyingtwo or mor coats of 100% premium acrylic emulsion paint having VOC less than 50gm / liter and UV resistance as per IS15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre /10sqm over and including priming coat of exterior primer applied @0.90 litre/10 sqm over old surfaces.complete allas specified and directed. |
| 127 | M&L for applying two or mor coats of 100% premium acrylic emulsion paint having VOC less than 50gm / liter and UV resistance as per IS15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre /10sqm over and including priming coat of exterior primer applied @0.90 litre/10 sqm over new surfaces.complete allas specified and directed. |
| 128 | Material and Labour for 75 mm thick PCC 1:4:8 type D-2 (using 40mm graded stone agg) as in sub base complete all as specified and directed. |
| 129 | Material and Labour for Sand filling under floor including watering and consolidation complete all as specified and directed. |
| 130 | Material and Labour for60mm thick rubber moulded glossy finished inter locking paver block with grey cement and pigment of any type and shape the minimum compressive strength not less then 350 kg/sqcm as approvedcomplete all as specified and directed. |
| 131 | M&L for Chequered cement concrete tiles 20cm x20cm x 25mm thick,set, jointed with grey pigment pointed in neat cement slurry in floors including 20mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 132 | Cleaning of firstmanholes of any description and in any position depth n’exc 1.5mtr deep mechanically or manually by taking off sludge waste/ night soil and silted soil from the existing manhole of any size, collecting and removalof sludge in sealed containerout side Air Force boundary and disposalof the samecomplete all as specified and directed |
| 133 | Demolition and breaking up drain pipes150 mm bore (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed. |
| 134 | M & L for 100mm Cast iron soil, waste pipes spun type , in any length with or without ears with cement joints, laid in trenches or in floors complete all as specified and directed. |
| 135 | M&L for reinforced concrete pipes, class NP-3, 150 mm bore, laid and jointed in cement mortar 1:1with collars and tested complete all as specified & directed. |
| 136 | M&L for cement concrete (1:3:6) type C-2 (using 40mm gradedcrushed stone aggregate) as in concrete bed to drain pipe including packing under and haunching against the sides of pipe after they are laid and tested complete for pipe of 100mm bore complete all as specified & directed. |
| 137 | M&L for cement concrete (1:3:6) type C-2 (using 40mm gradedcrushed stone aggregate) as in concrete bed to drain pipe including packing under and haunching against the sides of pipe after they are laid and tested complete for pipe of 150mm bore complete all as specified & directed. |
| 138 | Cutting into existing manholes for connecting new drains of internal dia of pipe150mm making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified & directed |
| 139 | Cutting into existing manholes for connecting new drains of internal dia of pipe100mm making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified & directed. |
| 140 | M&L for brick work with sub class "B" burn brick straight or curved on plan exceeding 6m mean radius using old size brick built in CM (1:4) complete all as specified and directed. |
| 141 | M&L PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate as in coping/ benchingsurface channel including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 142 | M&L for plain cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) in foundation, filling and mass concrete etc complete all as specified and directed. |
| 143 | M&L for providing pre-cast cement concrete1:2:4,type B-1 (using 20mm gradedcrushedstoneaggregate) as in cover slab , RCC flatform set in cement mortar 1:4 etc for cable ductand base for antenna or similar work etc complete all as specified and directed. (Note : Reinforcement shall be measured and paid separately under respective items of BOQ) |
| 144 | Taking down carefully existing unserviceable copper/ aluminium point wiring of any description & in any position with and includingPVC/steel conduit all fitting, accessories & fixtures such as switches, ceiling roses, pendants, regulators, socket, light fittings call bell, lamp holders etc and making good the disturbed surface of walls, floors, ceiling etc to match with the existing surfaces complete all as specified and directed. NOTE: Old fittings/fixtures/accessories like switches, sockets, lamp holders, regulators light fittings etc found in serviceable condition shall be removed carefully for reuse in the work and shall be paid for separately under respective item of BOQ. |
| 145 | Material and labour for point wiring for one light /fan/Exhaust fan point controlled by one switch with using 1.5 Sqmm (nominal area) stranded copper conductor, single core, PVC insulated & unsheathed cable FRLSH,1100 volts grade in and including concealed PVC conduits (Medium grade) of size not less than 20 mm dia all as directed with sunken type pressed steel terminal box and junction boxes 1.6mm thick of suitable size, duly painted with one coat of red oxide primer and two coats of black bituminous paint for mounting fittings and wiring to be terminated in pressed steel sunken boxes with laminated top sheet of 3 mm thick for housing of switchs, sockets, regulators etc including all accessories andusing 1.5 Sqmm (nominal area) stranded copper conductor single core conductor, PVC insulated & unsheathed cable as in earth wire connected to common earth dolly complete all as specified and directed. Note :-(I) The portion of point wiring at ceiling shall be in surface PVC conduit/ casing & capping of suitable size fixed on ceiling surface with using PVC rawl plugs. (ii)Fittings like switches, sockets, regulators, lamp holders, light fittings shall be measured and paid for separately under appropriate item of Schedule `A". (iii) The quoted rates shall be deemed to be inclusive for provision of covering sunken boards/terminal boxes / junction boxes of any shape and size with 3mm thicklaminated sheet fixed with suitable brass screws and cup washers |
| 146 | All as per Srl item No.2.45 above but for 5 pin switch socket outlet combination, 5/6 Amps point on independent board controlled by one switch 5Amp, one way, etc complete all as specified and directed. |
| 147 | All as per Srl item No.2.45 above but for 5 Pin 5 Amp socket outlet point controlled by one switch 5 Amps one way on same board, etc complete all as specified and directed. |
| 148 | All as per Srl item No.2.45 above but for one 3pin socket of 15Amp independent with PVC insulated and unseathed copper stranded conductor of size 2.5Sqmm including 1.5Sqmm PVC insulated and unseathed copper conductor for continuous earthing complete all as specified and directed. |
| 149 | All as per Srl item No.2.45 above but for One bell/buzzer point controlled by one push button on the same board with other switches etc complete all as specified and directed. |
| 150 | All as per Srl item No.2.45 but one light point controlled by two, two way switches etc complete all as specified and directed.. |
| 151 | M&L for Modular switch,one way 6 Amps 240 volts, 1 module ISI marked white ivory finish complete all as specified and directed. |
| 152 | M&L for Modular switch,two way 6 Amps 240 volts, 1 module ISI marked white ivory finish complete all as specified and directed. |
| 153 | M&L for Modular bell push flush type 6 Amp 1 module, 240 volts,complete all as specified and directed. |
| 154 | M&L for Modular socket6A, 2/3 pin combined 2 module, 240 volts, ISI marked white ivory finish complete all as specified and directed. |
| 155 | M&L for Modular switch socket combination6A, 2/3 pin combined 2 module, 240 volts, ISI marked white ivory finish complete all as specified and directed. |
| 156 | M&L for Modular switch socket combination16A, 6 pin combined 3 module, , ISI marked white ivory finish complete all as specified and directed. |
| 157 | S&F ceiling rose, surface bakelite 18 mm X 50 mm AC, 230 V polycarbonate isolated body, two or three terminals complete all as specified and directed. |
| 158 | S&F lamp holder PVC/Polycarbonate type with cord grip cap/back platesuitable for batten/angle /pendent fitting complete all as specified and directed. |
| 159 | M&L for bell ding dong, AC 230 V single pole,complete all as specified and directed. |
| 160 | Supply and fixing step type Modular electronic fan regulator single phase, 230 volt, 100/120 watt complete all as specified and directed. |
| 161 | S&Fin repair decorative slim linear LED tube light fitting batten Type 01x20 watt light with co extruded polycarbonate body, environmental friendly, energy efficient ready to use pack with all accessories and connecting the same to ceiling rose with using copper conductor 24/0.20 flexible PVC sheathed and fixing arrangement for fixing the light fitting to wall/ roof surface complete all as specified & directed by Engineer in-charge. |
| 162 | Supply and fixingin repair Street/Security light fittings 1X35W new generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP66 roadway luminaire with high power LED as light source with acrylic cover suitable for pole dia of 40mm (Max) with complete (40 mm GI pipe light grade ), clamp, nut-bolt and washers with impact and corrosion resistant including thermal management in multiple optics complete all as specified & directed by Engineer in-charge. |
| 163 | Disconnecting & taking up or down existing unserviceable MCB DB VTPNwith all MCB"s/Isolator & metal clad box of any description and in any position with existing fittings (MCB"s) complete all as specified & as directed. |
| 164 | Supply and fixing of sheet metal enclosure Double door for DB’s8 way 240 Volts with 200 Amps rated bus bar for single phase and neutral supply complete fixed properly on in concealed position and to connect their incoming/outgoing electric connections by means of suitable sizes of lugs/thimbles and to provide required sizes of flexible conduit at any open surfaces near DB’s of cables/wires all as directed. |
| 165 | S & F factory made epoxy powder coated distribution board TP & N 4 ways (VTPN MCCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with Knockouts including provision for housing MCCB in the incoming and MCBs in the out goingcomplete all as specified & directed . |
| 166 | Dismantling & Taking out MCBs/Isolator/MCCB & metal clad box any size, any type and capacity complete all as specified and directed. |
| 167 | S&F MCB SP 6 to 32 Amps ("B" Series) having current rating 10 kA, 240 Vcomplete all as specified and as directed. |
| 168 | S&F MCB SPN 40 to 63 Amps ("B" Series) having current rating 10 kA,240 V complete all as specified and as directed. |
| 169 | Supplying & fixing MCCB, 3 pole, 125 Amps, 50Hz, 415 Volts with rupturing capacity 16 KA with thermal magnetic release and adjustable overload setting having type DPX 160 fixed in distribution board, complete all as specified & directed. |
| 170 | Disconnecting & taking up or down u/s submain wiring of aluminium/copper conductor with two run/four run of single core earth cable of any description, any size & in any position including taking out existing conduits of any description and making good the disturbed surface to existing surfaces complete all as specified and directed. Note:- Two run/ four run of single core PVC cable with one run of earth conductor shall be measured as one unit) |
| 171 | M&L for surface/concealed submain wiring as required with two single core FRLSH PVC insulated and unsheathed copper stranded conductor of size 4 Sqmm 1100 Volts and one run of copper stranded conductor of size 4 Sqmm for continuous earthing drawn in and including rigid non metallic PVC conduit pipe ISI marked of size not less than 20 mm dia including to connect their incoming/outgoing electric connections by using required sizes of lugs/thimbles as well as flexible conduit of suitable sizes shall also be used at any open surfaces of conductor complete all as specified and directed. Note :-(i) Two single corecable and one run of earth copper conductor including conduit will be measured and paid as one unit length. (ii)The quoted rate shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc of any description for conceling the conduits to required depth and making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. |
| 172 | M&L for surface/concealed submain wiring as required with two single core FRLSH PVC insulated and unsheathed copper stranded conductor of size 6 Sqmm 1100 Volts and one run of copper stranded conductor of size 6 Sqmm for continuous earthing drawn in and including rigid non metallic PVC conduit pipe ISI marked of size not less than 25 mm dia including to connect their incoming/outgoing electric connections by using required sizes of lugs/thimbles as well as flexible conduit of suitable sizes shall also be used at any open surfaces of conductor complete all as specified and directed. Note :-(i) Two single corecable and one run of earth copper conductor including conduit will be measured and paid as one unit length. (ii)The quoted rate shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc of any description for conceling the conduits to required depth and making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. |
| 173 | Taking down carefully Exhaustfan/Ceiling fan from existing place and removing to MES store yard Scraping, cleaning & painting with two coats of super enamelled paints (as approved by GE) greasing/oiling and refixing at site complete including electric connection withthree core flexible wire 1.5 sqmm complete all as specified and directed. |
| 174 | S&F exhuast fan, steel body AC single phase 230V of size 450mm sweep heavy duty with blade, frame and louversall all as specified and directed. |
| 175 | M&L for Earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in theground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground levelconnected to galvanized iron wire 4mm diaas earth leadby means of bolts, nuts and washers of GIup to test point, GI tubing20 mm bore light grade protection pipe, GI watering pipe 20mm bore medium grade with funnel and wire mesh, charcoal, magnesium, salt etc& 50mm thick pre-cast RCC (1:2:4) type B-1 (Nominal mix) cover withreinforced with 8 mm dia TMT bar @100 mm centre to centre both ways with mild steel handle 12 mm dia, plastering 12 mm thick in cement mortar (1:6) internally and upto 150 mm below ground level externally with suitable steel handle and angle iron 40X40X6mm frame and chamber of PCC (1:3:6) type C-1 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, includingtaking down of existing earthing complete all as directed. Notes: 1.Earth lead & protection pipes length upto & including 7.50 metre. 2.Earth filling shall be done by vegetable soil. 3.Soil should be free from stone, boulders, aggregate, gravels etc. |
| 176 | S&F for LED mirror lightfitting ( 2 feet)1 x 10 watt batten type LED, complete with all accessories, prewired and making connection with and including 23/0.0076 flexible copper wire three core from connector to ceiling rose not more than 1.2 mtr, fixed on wall firmly complete all as specified and directed. |
| 177 | Supply, laying , jointing & testing XLPE insulated,screened ,PVC bedded, galvanised steel strip or wire armoured, electirc power cable ( heavy duty) with standard aluminium conductor , 1100 Voltsgrade of cross sectional area 35 Sq mm 3.5 core including taking out of cable any type and capacity from trenches ,pole,road etc including necessary joints & bricks & removing form site complete all as specified and directed. Note : Excavation , earth work, sand cushioning for cable and cable protection cover shall be measured & paid under respective item. . |
| 178 | Excavation in trenches in soft & loose soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope/gradient forlaying cables/pipes etc.complete all as specified and directed by Engineer-in-Charge. |
| 179 | Returning, filling in including spreading, levelling, watering and well ramming in layers of25 cm thickafter the cables etc. are laid, jointed & tested complete all as specified and directed by Engineer-in-Charge. |
| 180 | Removal of surplus excavated soil not exceeding 50 Mtr distance and depositing where directed by Engineer-in-Charge at a level not exceeding 1.5 m above the starting point complete all as specified and directed. |
| 181 | M &L for sand filling with clean, dry and sieved fine natural river sand in two portion,including gently punning around cables after the cables are laid, in trenches for cable protection complete all as specified and directed. (NOTE: Only punned thickness measured). |
| 182 | Supply & Laying Sub Class `B’ bricks old size with axis of the bricks perpendicular to the axis of the cable as in cable protection complete all as specified and directed. |
| 183 | S&F Tube medium grade galvanised Tubeof dia 50 mm for road crossing of cable and on pole and DB cable as in cable protection complete all as specified and directed. |
| 184 | Taking down carefully from existing place for re-use of geyser by disconnecting electric /water supply connection and refixing the same after civil work including all electric /water supply connection connecting with suitable wire all as specified and directed by Engineer-in-Charge. |
| 185 | Taking down carefully from existing place for re-use electric meter by disconnecting electric supply connection and refixing the same after civil work including all electric supply connection connecting with suitable wire all as specified and directed by Engineer-in-Charge. |
| 186 | S&F of Electric water heater storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 Ltrs ,BEE 5 star rated complete with all accessories such as safty valve ,Thermostate ,NRV,connection piece etc omplete all as specified and directed . |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
