Construction Of Community Toilet At Damdim More, Under Damdim Gp, Mal Development Block, Schemd Id - 58006004
Tender Value
8.01 Lakhs
Estimated cost
Bid Submission
10 Jan 2024
0 days left
EMD
6100
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalpaiguri → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Community Toilet At Damdim More, Under Damdim Gp, Mal Development Block, Schemd Id - 58006004
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 03-Jan-2024 | Extension of Critical Date and conditions | Date | 10-Jan-2024 |
BOQ
| Sl. No. | Item Description |
| 1 | P-1, it-2(a)Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.Depth of excavation not exceeding 1,500 mm. |
| 2 | P-1, it-3(a)Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) |
| 3 | P-2, it-4(A)(A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) |
| 4 | {(PWD(B) Page-47 item-3}Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 5 | P-24, it-4(a) , (Rate Analysis)Cement concrete with 30 mm down graded shingles excluding shuttering. N.B. Variety.(a) 1:3:6 proportion. |
| 6 | P-26, it-10(i)Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. |
| 7 | P-42, it-36(a)Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) (a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge |
| 8 | P-22, it-1 (corri-3)25 mm. thick damp proof with cement concrete (1:1.5:3) (with graded stone aggregate 10 mm. normal size) and painting the top surface with a coat of bitumen [VG.40 ] using 1.7 kg. per sq.m. including heating the bitumen and cost and carriage of all materials complete. [Bitument to be supplied by the Agency] |
| 9 | P-016, it-16125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor |
| 10 | P-43 (10th corrigenda Page 1), it-40(a)Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. For works in foundation and upto roof of ground floor/upto 4 m (i) Tor steel/Mild Steel (SAIL /TATA/RINL) |
| 11 | P-49, it-1 (corri-3)Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor). (i) 20 mm thick plastering (out side) |
| 12 | P-49, it-1 (corri-3)Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor). (i) 20 mm thick plastering (out side) (ii) 15 mm th. Plastering (inside) |
| 13 | P-192, it-15Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m. |
| 14 | P-64, It-35 , 3rd Corrigenda.(P-35, It-22)Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc in ground floor (i) with 20mm thick CM 1:4 in floor,(b) Area of each tile above 0.09 Sq.m, (i) Coloured decorative |
| 15 | P-64, It-35 , 3rd Corrigenda.(P-35, It-22)Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc in ground floor (i) with 20mm thick CM 1:4 in floor,(b) Area of each tile above 0.09 Sq.m, (i) Coloured decorative (ii) with 15 mm thick CM 1:3 in wall (a) Area of each tile upto 0.09 Sq.m coloured decorative |
| 16 | P-134, It-27PVC Door Shutter-30 mm thick: Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of 59 mm x30 mm section ...........tower bolt / door ring are required to be strong enough to with stand wear and tear. The rate is inclusive of cost of all materials, labour, and hire of tools and plants and appliancesi/c carriage of all materials.... |
| 17 | P-104, It-13:- (a)(i)M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, .... fitted and fixed with necessary screws and lugs in ground floor. (Add extra @ 1% for each addl. floor upto 4th floor ....) (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr. [Rate for 1st floor = 7238.00 + 1% = Rs. 7,310.38] |
| 18 | P-105,It-15Supplying 1.5mm thick M.S. sheet fitted and fixed on one or both faces of M.S./ W.I. gate etc. with point welding at not more than 150mm apart complete in all respect as per design including cost of all labour and materials. |
| 19 | (P-107, IT-20/b)Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle....in all respect excluding glazing. (b) Openable steel windows as per IS sizes with side hung shuttersand horizotal glazing bars. [The extra rate admissible for the openable portion only] |
| 20 | P-205, It-1Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6m height for external wall) (i) 3 mm thick (weighing 7.4 kg/Sq.m) |
| 21 | P-200, IT-1/aa)Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc |
| 22 | (P-200, IT-2/b/ii)(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface :With super gloss (hi-gloss) (ii) Two coats (white in shade) |
| 23 | P-200, It-1: (b)Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 24 | P-194 It-4: (A) Colour washing with any shade with Stainers, as required including cleaning and smoothening surface thoroughly : (i) Internal surface (All floors) (b) Two coats (on new works only). (i) Other than yellow, pink. |
| 25 | P-194 It-4: Colour washing with any shade with Stainers, as required including cleaning and smoothening surface thoroughly : (ii) External surface (Ground floor) (b) Two coats (on new works only). (i) Other than yellow, pink. |
| 26 | Page-79; It-4: Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding \"P\" or \"S\" trap (excluding cost of concrete for fixing). |
| 27 | Sec_B (II)It. No 14 Page65 Supplying,fitting and fixing cast iron \"P\" or \"S\" trap conformimg to I.S. 3989 / 1970 and 1729 / 1964 including lead caulked joints and painting two coats to the exposed surface (A) \"P\" Trap (iii) 100 mm |
| 28 | Sec_A(IV), It.No 2, Pg 36Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc |
| 29 | P-81, It-11Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete.i) Polythene Flush Pipe |
| 30 | P-80, It-6 (B)-(III) WATER CLOSETS AND URINALS:- Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75mm X 75 mm X 75 mm wooden blocks complete. (ii) 470 mm X 280 mm X 340 mm |
| 31 | P-80, It-7: Supplying, fitting and fixing Squating plate with integral flushing in white vitreous chinaware of approved make in cement concrete (6:3:1) with jhama chips complete. (Payment of concrete will be paid seperately). (i) 450 mm X 350 mm |
| 32 | P-81, It-12(B)-(III) WATER CLOSETS AND URINALS:- Supplying, fitting and fixing urinal flush pipe fittings of approved brand. (a) C.P. urinal flush pipe fittings range of one |
| 33 | P-12, It-19(I):- SECTION (A) - PLUMBING WORKS:-Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (a)Exposed surface(i) 32 mm |
| 34 | (ii) 25 mm |
| 35 | (b) For Concealed Work (i) 20 mm |
| 36 | (ii) 15 mm |
| 37 | P-69, It-23:- SECTION (B) - SANITARY AND DRAINAGE WORKS (B)-(II) SOIL PIPE AND FITTINGS:- (i) Supply of UPVC pipes (B Type) & fittings Single Socketed 3 Meter Length (b) 110 mm |
| 38 | Sec_1M, It.No 21, Pg 212Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/ Bitumen/M-Seal etc) complete (i) 110 mm dia pipes |
| 39 | (ii) 110 mm dia 87.5 degree bend |
| 40 | (iii) 110mm dia shoe |
| 41 | P-6,It-7 (e):-SECTION (A) - PLUMBING WORKS:-PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent) 15 mm Bib cock |
| 42 | Stop cock |
| 43 | It. No.-2(ii), P-41 Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint. |
| 44 | PageNo -37,Item No-6,bSupplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer.1000 litre capacity |
| 45 | P-89, It-4: 7th CorrigendaConstruction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia (Other than SAIL/TATA/RINL) |
| 46 | [Ref: P.W.D. (Roads) item no. 8.07, Page-265]Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,PartI. Payment will be made separetly on the basis of actual height based on relevant I.S.Code.For 10 users With Pakur variety. (Other than SAIL/TATA/RINL) |
| 47 | NON SCHEDULE ITEMElectric Wiring and New connection charge & other fittings & labour charges for Electrification work.(L,S) Fan - 1 no, Tube Light - 3 Nos, Bulb 9wt LED -5 Nos, Wire 1mm - 2 coil, Casing 1.8 mt - 10 Nos |
| 48 | Tube Light |
| 49 | Bulb (LED 9wt) |
| 50 | Wire (1.0mm) |
| 51 | Casing (6ft Long) |
| 52 | New Meter Connection with Wire from department |
| 53 | 1HP Pump Kirloskar make |
| 54 | Mistry With Labour |
| 55 | [Ref: P.W.D. (Roads) item no. 8.07, Page-265]Providing & fixing Concrete Sign Board as per IRC specification of size 900 x 750 x 37 mm. thick made with RCC 1:1½:3 with pakur variety stone chips reinforced with double layer IRC febric (75 x 75 mm. mesh) and fixed with necessary nuts & bolts on two RC precast posts 100 mm. x 150 mm. of height 2.65 m. of which top 750 mm. is of section 100 x 13 mm. and 1.90 metre above GL & 0.75 metre below GL including digging hole, repacking the same with cement concrete 1:3:6 with jhama khoa or with local stone chips etc. complete including painting two coats on both faces lettering sign marks etc. as per direction of the Engineer-in-Charge. (The rate is inclusive of cost of reinforcement, concrete, shuttering, nuts & bolts, washer etc. complete.) |
| 56 | Add:- GST @ 18% |
| 57 | Add:- Cess @ 1% |
AI Tender Summary
Tender Timeline
Jan 03, 2024
11:30 IST
Tender Published
Tender notice published.
Completed
Jan 10, 2024
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
CompletedJan 10, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJan 13, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender