Renovation Of Conference Hall In Cnid At It And Tg Building First Floor Ecil Hyderabad 1 1 Removing of existing PVC flooring etc., complete and as directed by Engineer-in-charge. 2 2 Dismantling existing fixed MS glass/weld mesh/cement asbestos/other hard board partition including door window, fittings etc., by welding, cutting, disposal of unserviceable material within 1.0 KM lead etc., complete and as directed by Engineer-in-charge. 3 3 Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 1.0KM lead as directed by Engineer-in-charge. 4 4 Providing and laying 2mm thick Vinyl plank flooring including cleaning the surface, laying the sheets by applying rubber adhesive of fevicol 305/505/SR998/equivalent etc., complete and as directed by Engineer-in-charge. 5 5 Providing and fixing of Daiken / Armstrong mineral fibre false ceiling with hot dipped galvanized steel grid work, surface chemically cleaned capping perfectly pre finished in baked polyster paint, main tees of size 33x24x0.5mm thick to form a grid of size 600x600mm and suspending the grid from RCC roof using 12 guage GI wire and rawl plug at every 1200mm intervals wherever required and laying Daiken/Armstrong mineral fibre acoustic ceiling tiles pattern of size 600x600x14mm over the formed grid etc., complete and as directed by Engineer-in-charge. Note: False ceiling tiles not laid at the place of electrical fittings should be handed over to department - ESD stores. 6 6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) 7 7.1 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) Code Description Unit Quantity 8 8.1 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) 9 9 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarsd sand) finished rough with sponge. 10 10 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Make: Birla white / Star / Saintgobian 11 11 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. Make: Asian / Nippon / Berger Water thinnable cement primer 12 12.1 Wall painting with premium acrylic emulsion paint of interior grade, VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats 13 13.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work 14 14.1 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 15 15 Supply and fixing of roller type venetian blinds (design/code no.50179-8) or as per user s requirement with necessary accessories and approved colour etc., complete and as directed by Engineer-in-charge. 16 16.1.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) 17 16.2.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) 18 17.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 19 17.2 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) 20 18 Providing etching on float glass panes etc., complete and as directed by Engieer-in-charge. 21 19 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides 22 20.1 Providing and fixing powder coated aluminium handles of ISI marked (minimum thickness of powder coating 50 micron) to required colour or shade, with necessary screws etc. complete : 125 mm 23 21.1 Providing and fixing powder coated aluminium tower bolts of ISI marked (minimum thickness of powder coating 50 micron) to required colour or shade, with necessary screws etc. complete : 150x10 mm 24 22 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer ( brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. 25 23 Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. 26 24 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 27 25 Providing and fixing aucoustic wall paneling made of 12mm thick waterproof plywood on one side of make- termite proof green ply/tru ply. On plywood top fixing of 1mm thick decolam sheet of approved colour and make of royal touch or equivalent with fevicol and necessary screws (nailing not allowed) including cost of cornices/bands, transportation of material and labour etc., complete and as directed by Engineer-in-charge.
