Kerala State Rural Roads Development Agency has published Periodic Maintenance Of Road –Package No: Kr0132 -Omanappuzha Jn Malsyathozhilali Colony Road In Aryad Block, Alappuzha District- Using Financial Incentive 2022-2023 Received Under Pradhan Mantri Gram Sadak Yojana (Kerala). Submission Date for this Tender is 16-12-2023. Road Repair Tenders in Thiruvananthapuram Kerala. Bidders can get complete Tender details and download the document.
Sl. No. | Item Description |
1 | Pothy Velloor Road ( 3.790kms) |
2 | APPENDIX A : CLEARING AND GRUBBING |
3 | Clearing Grass and Removal of Rubbish - Clearing grass and removal of rubbish upto a distance of 30m outside the priphery of the area as per technical specification of MoRD |
4 | APPENDIX B : PAVEMENT COMPONENTS |
5 | Construction of embankment with material obtained from Private land Borrow Pits - Construction of embankment with approved material deposited at site from borrow pits with a lift upto 1.5m, transporting to site, spreading, grading to required slope andcompacting to meet requirement of Table 300.1 and 300.2 as per technical specification Clause 301.5 -( Contractors own earth) |
6 | Wet Mix macadam -providing, laying, spreading and compacting stone aggregates of specified sizes to wet mixmacadam at OMC in mechanical mixer (pug mill), carriage of mixed material by tipper to site,layingin uniform thickness in sub-base / base course on a well prepared sub-base and compactingwith smooththree wheel 80-100 kN static roller to achievethe desired density including lighting, barricading and maintenance of diversion etc as per table 400.11 & 400.12 and as per technical specification Clause 406-pot hole filling |
7 | APPENDIX C : BITUMINOUS LAYERS |
8 | Modified penetration macadam - 50 mm thick using Packed Bitumen S-65 -Construction of penetration macadam over prepared base by providing a layer of compacted crushed course aggregate using chips spreader with alternate applications of bituminous binder and key aggregates a rolling with a three wheel 80 - 100 kN static roller to achieve the desired degree of compaction as per technical specification clause 506 |
9 | Prime Coat - Low porosity-providing and applying primer coat with bitumen emulsion (Packed SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at a rate of 0.70 - 1.00 kg/sqm using mechanical means as per technical specification clause 502 |
10 | Tack Coat - Providing and applying tack coat with bitumen emulsion (Packed RS-1) using emulsion distributorat a rate of 0.25 - 0.30 kg/sqmon the prepared granular surface treated with primer &cleaned with Hydraulic broom as per technical specification clause 503 |
11 | Tack Coat - Providing and applying tack coat with bitumen emulsion (Packed RS-1) using emulsion distributorat a rate of 0.20 - 0.25 kg/sqmon the prepared bituminous surface cleaned with Hydraulic broom as per technical specification clause 503 |
12 | Mix Seal Surfacing - Manual Means - Type A - Providing, laying and rolling of close-graded premix carpet of 20mm thickness composed of 11.2mm to 0.9mm (Type-A) or 13.2mm to 0.9mm (Type-B) aggregates either using penetration grade bitumento required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100kn roller, finished to required level and grades as per technical specification clause 509- UsingBitumen Bulk S-65 by Manual Means |
13 | APPENDIX D : CD WORKS |
14 | Plastering with cement mortar 1:4, 12 mm thick,one coat on concrete workas per technical specification Clauses 613.4 & 1204 |
15 | Painting on Concrete /Steel surfaces with Epoxy- Painting two coats of epoxy paint icluding primer coatof approved brand on concrete/steel structuresafter thorough cleaning of surface to give an even shade as per drawing and technical Specification clause 1701 |
16 | PCC Grade M 20 - Providing concrete for plain/reinforced concrete for wearing coat complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203- Nominal mix 1:2:4 |
17 | Engaging man mazdoor for cleaning/removing deposits/removing silt/clearing of jungle,waste etc from the ventways of existing culverts, sumpits and existing drains |
18 | APPENDIX E : Traffic Signs |
19 | Providing and Fixing "Logo" of PMGSY Project - Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 |
20 | Providing and Fixing typical PMGSY citizens information board as per MoRD specifications and drawings-Two vertical76.1mm outer diameter MS sheet tube posts of 3.60mm thickness (medium class)duly embedded in cement concrete M-15 grade blocks of 600mm x 600mm x750mm, 600mm below ground level with two horizontalM S Sheet Tubesof 1000mm length to make the frame of board, four horizontals and two verticalswith M S Sheet rectamngular Tube 50x25x2mm to make the frame to fix the board as per drawing, two M S Sheet 2.00 mm thick boards of size 900x750mm strengthened by 25mmx5mm MS flat iron includingpainting with stove enameled paint on both sides as per MoRD specifications. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 |
21 | Providing and Fixing typical PMGSY Maintenance information board as per MoRD specifications and drawings-Two vertical76.1mm outer diameter MS sheet tube posts of 3.60mm thickness (medium class)duly embedded in cement concrete M-15 grade blocks of 600mm x 600mm x750mm, 600mm below ground level with two horizontalM S Sheet Tubesof 1000mm length to make the frame of board, four horizontals and two verticalswith M S Sheet rectamngular Tube 50x25x2mm to make the frame to fix the board as per drawing, two M S Sheet 2.00 mm thick board of size 900x1500mm strengthened by 25mmx5mm MS flat iron includingpainting with stove enameled paint on both sides as per MoRD specifications. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 |
22 | Providing and fixing of retro-reflectorised logo board at different locations of roadasper IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI pipe 50 mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 1701- 600mm x 600mmsize logo and sign board of 1100x300mm |
23 | Traffic Signs- Retro-reflective Single Chevronof 50cm x 60cmsize - Providing and fixing of retro-reflectorised single chevron sign asper IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI pipe 50 mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 1701 |
24 | Kilometre Stone- Reinforced cement concrete M15 grade kilometre stone / local stone of standard design as per IRC:8 fixing in position including painting and priming etc.as per drawing and technical Specification clause 1703 - OrdinaryKilometre stone (pre-cast) |
25 | Kilometre Stone- Reinforced cement concrete M15 grade kilometre stone / local stone of standard design as per IRC:8 fixing in position including painting and priming etc.as per drawing and technical Specification clause 1703 - 200m stone (pre-cast) |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail