Tender For Conference Tables (1 No.) And Conference Charis (10 Nos.) At Cife, Mumbai, Mumbai-Maharashtra

Tender For Conference Tables (1 No.) And Conference Charis (10 Nos.) At Cife, Mumbai (A) Conference Room Table (1 No.) Conference table of 10 seater capacity (Godrej or Equivalent) General Specifications (1) Work surface: Top surface should have Veneer finish Top thickness 31mm Thick +1.5mm (18 mm+12 mm MDF as per IS 12406 + Natural Veneer on Top Surface and balancing laminate on Bottom Surface), Chamfer Edges & Veneer Portion of Work surface in finished in PU Matt Paint. (2) Under structure (i) Legs: Made from 1.6 mm Matt Silver Anodized Aluminium Extrusion. Leg Assembled together with a plastic holder at bottom and 5 mm HR steel (IS: 2062) which is powder coated (DFT 40-60 Microns). The Plastic glide holder should have provision for wire entry and glide fixing. The wire carrying should be facilitated through the hollow space between two leg extrusions and the wires should be concealed between removable rigid PVC extrusion in the leg. (ii) Veil & Cross Members: Should be made from 18mm Thick PLT + 1mm as per IS – 12823 and PVC edge banding on all the sides. (iii) Access Flap & Switch Mounting Tray: Made from Matt silver Anodized Aluminium extrusion and plastic moulded components to facilitate access of Electrical/Data/Voice sockets access from top. Powder coated (DFT 40-60 Microns) switch mounting tray made from 0.8/1.2 mm CR Steel IS-513. (iv) Electrical Points: There should be provision for electrical points. Switches to be mounted on tray as per requirement. Provision should be made for mounting 8 - module Anchor Roma switch plate on switch-mounting tray. (B) CONFERENCE ROM CHAIRS (10 Nos.) (1) Seat/back Assembly: The seat and back should be made up of 1.2 + 0.1cm. thick hot-pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam should have contoured lumbar support for extra comfort. The seat should have extra thick foam on front edge to give comfort to popliteal area. Model: MID Back (Size: 47.5 cm. (W) x 58.0 cm. (H)) (Approx.) (2) Chair Dimensions Base width (W): 76.3 cm Depth (D): 76.3 cm Height (H): 85.5 to 97.5 cm Seat height (SH): 42.5 to 54.5 cm (Dimensions may vary (+ or - ) by 1 cm. (3) High resilience (HR) Polyurethane Foam: The HR polyurethane foam (moulded with density = 45+2 kg/m3 and hardness load 16+2 kg) as per IS: 7888 for 25% compression. (4) Armrests: The one-piece armrests should be injection moulded from black co-polymer Polypropylene. (5) Center Tilt Synchro Mechanism: The mechanism should be designed with the following features:  3600 revolving type.  Upright position locking  Tilt tension adjustment  Seat/back tilting ratio of 1:3 (6) Other Specifications ● Powder coated tubular frame Tubular Frame ● Pneumatic height Adjustment (adjustment stroke of 12.0 + 0.3 cm) ● Telescopic Bellow Assembly: the bellow should be 3-piece telescopic type and injection moulded in black Polypropylene. ● Pedestal Assembly: The pedestal should be injection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 + 0.5 cm. pitch-centre dia. (76.3+1.0 cm with castors). ● Twin wheel castors: The twin wheel castors should be injection moulded in Black Nylon. 1. Conference Table 1 2. Conference Room Chairs 10

Refer document

Refer document