Tender For Special Repair To Road From Jco Mess And Internal Road At Mariani At Jorhat Mil Station., jorhat-Assam

Tender For Special Repair To Road From Jco Mess And Internal Road At Mariani At Jorhat Mil Station.; 1 S&F Cat Eye Solar Reflective Type Of Metal Body Alloy Of Size 100X100x20mm With Pama Striplens Reflector Fixed With And Including Ms Stud Of Suitable Size As Per Manufacturer Instructions Complete All As Specified And Directed By The Engr-In-Charge. 2 S & F Solar Road Studs Of Size Not Less Than 125X 125 X 25 Mm Made Of Weather Resistance Aluminium Alloy And Poly Carbonate Material Electronically Welded Micro- Prismatic Lens With Abrasion Resistant Coating As Approved By The Engineer In Charge. The Cats Eye Shall Support A Load Of 13635 Kg Tested In Accordance With Astm D4280. The Slope Of Retro- Reflective Surface Shall Be 35° ± 5° To Base. The Reflective Panels On Both Sides With At Least 12 Cm Of Reflective Area Up Each Side. The Luminance Intensity Should Be As Per The Specification And Shall Be Tested As Described In Astm E: 809 As Recommended In Bs: 873 Part 4 :1973. The Studs Shall Be Fixed To The Road Surface Using The Adhesive Conforming To Is, As Per Procedure Recommended By The Manufacturer Complete And As Per Direction Of Engineer-In-Charge. The Solar Panel Shall Be High Efficiency Mono Crystalline 2.5 V / 60 M A And The Battery Shall Be One Ni-Mh Type ( 1.2 V / 1200 M Ah ) High Temp For Backup Of 36 Hours Full Charging. The Flash Frequency Shall Be 60 ± 5 Times Per Minute. Make- Model No 111 Jugnu Of Dark Eye Or Equivalent Makes As Given In Appx B 3 Supply And Fix Plastic Speed Bump Of Size 50 Mm ( Height ) X 245 Mm ( Width ) X 350 Mm ( Length ) , Abs Block Black And Yellow & 02 No High Reflective Reflectors Moulded In Pmma, Fixed With Nails And Epoxy / Thermoplastic Adhesive ( Bas Bumper And Hole ) With Two Different Colourband Pattern On Road Surfaceall As Per Manufacturers Instructions And Complying To Guidelines Issued By Min Of Road Transport. Etc. Complete. Make- Da-1005 Of Dark Eye Or Equivalent Make As Given In Appx B. 4 S & F Metal Tubular Delineators ( Road Way Indicators ) Made Out Of Abs Round Body Fitted With 2 Nos Of 65 Mm Dia Highly Reflectivereflectors Made Out Of Pmma And Mounted On 45 / 50 Mm Mild Steel Pipe Of 600 Mm Height Duly Power Coated And Thermo Plastic Elastomers 3 Bands Of Green, Red And Yellow Reflector Radium Tape Of 25 Mm Wide Strip With Anti Theft Steel Net For Reflector Protection Including Embedded 200 Mm Below Ground Level Including Excavation And Pcc M15 ( Nominal Mix ) With Using 20 Mm Graded Stone Aggregate In Foundationand Making Good Surface Complete All As Specified And As Directed. 5 Scarifying Or Picking Gravelled, Macadam Or Bituminous Macadam Surfaces In Area Not Exceeding 400 Sqm, Depth Of Pot Hole Exceeding 50 Mm But Not Exceeding 100 Mm Including Rolling Over The Broken Surfaces Using 8 To 10 Tonnes Power Roller To Required Camber And Gradient Complete All As Specified And As Directed. 6 M & L For Bituminous Macadam Not Exceeding 75 Mm Thickness ( Compacted Thickness ) Using Hot Mix Plant And Mechanical Paver With 4% Binder ( Paving Grade Bitumen Vg-30 Grade ) Content By Weight Of Total Mix, Rolled And Compacted With Power Roller 8 To 10 Tonnes To Required Camber And Gradient Complete All As Specified And As Directed. Note :- ( I ) Bituminous Macadam Shall Be Laid Using Self Propelled Hydrostatic Paver Finisher And Preparation Of Mix Shall Be Using Hot Mix Plant And Transporting The Mix In Tipper. ( Ii ) The Exact Bitumen Content Required Shall Be Determined As Per Irc 27: 2009. The Adjustment In Rate On Minus Side Variation In Quantity Of Bitumen If Any Shall Be Priced At The Rate Of ?55 Per Kg. No Claim Whatsoever Shall Be Made For Adjustment In Plus Side. 7 Preparing Existing Black Top Surfaces By Brushing With Wire Brushes For Removing Caked Mud Etc., Sweeping With Brooms And Finally Fanning The Cleaned Surface With Gunny Bags To Remove All Loose Dirt Etc. Complete All As Specified And As Directed. 8 M & L For Applying Evenly A Tack Coat With Bituminous Primer ( Paving Grade Bitumen Vg-10 Grade ) @ 5 Kg Per 10 Sq Metres Complete All As Specified & As Directed. 9 M & L For Bituminous Concrete 40 Mm ( Compacted Thickness ) Using Graded Crushed Stone Aggregate Premixed With Binder ( Paving Grade Bitumen Vg-30 Grade ) @ 5.5% By Weight Of Total Mix & Hydraulic Lime / Cement ( Opc-43 Grade ) Filler, Rolled And Compacted To Required Camber And Gradient Complete All As Specified And As Directed. Note :- ( I ) Semi Dense Bituminous Concrete Shall Be Laid Using Self Propelled Hydrostatic Paver Finisher And Preparation Of Mix Shall Be Using Hot Mix Plant And Transporting The Mix In Tipper. ( Ii ) The Exact Bitumen Content Required Shall Be Determined Following The Marshall Mix Design Procedure Contained In The Asphalt Institute Manual Ms-2 ( Sixth Edition ) As Referred In Case 3.5.3 Of Irc 111: 2009. The Adjustment In Rate On Minus Side Variation In Quantity Of Bitumen If Any Shall Be Priced At The Rate Of ?55 Per Kg. No Claim Whatsoever Shall Be Made For Adjustment In Plus Side. 10 Providing And Applying 2.5 Mm Thick Road Marking Strips ( Retro-Reflective ) Of Specified Shade / Colour Using Hot Thermoplastic Material By Fully / Semi-Automatic Thermoplastic Paint Applicator Machine Fitted With Profile Shoe, Glass Beads Dispenser, Propane Tank Heater And Profile Shoe Heater, Driven By Experienced Operator On Road Surface Including Cost Of Material, Labour, T & P, Cleaning The Road Surface Of All Dirt, Seals, Oil, Grease And Foreign Material Etc. Complete All As Specified And As Directed. 11 Repair To Potholes Any Depth, Not Exceeding 1 Sqm Each Including Sweeping Free From Dust And Mud, Or Water, Scoring Sunken Surfaces In Roads, Paths, Etc., Cutting Around Edges To At Least 25 Mm In Depth, Making Good By Filling In Screened & Graded Road Metal, Watering And Well Ramming ( Including Supply Of Road Metal ) , Rolled And Compacted With Power Roller 8 To 10 Tonnes To Required Gradient And Camber Complete All As Specified And As Directed. 12 M & L For15 Cm Thick ( Compacted Thickness ) Wbm, In Two Layers Of75mm Thk Each ( Each Layer To Be Rolled And Cosolidated Separately ) With Coarse Aggregates Ofsand Stone, Flint Or Quartzite Of Grading 2 ( 63 To 45 Mm Size ) , Spread, Rolled And Compacted To Required Gradient And Camber With Three Wheel-Power Roller Of 80 To 120 Kn Capacity Or An Equivalent Vibratory Roller Complete All As Specified And As Directed. 13 M & L For Applying Primer On The Surface Of Non-Bituminous Granular Base Course Preparatory To The Superimposition Of Bituminous Treatment Coat With Cationic Bitumen Emulsion Ss-1 Grade At The Rate Of 10 Kg Per 10 Sqm Of Surface Complete All As Specified And As Directed. 14 Preparing Unsurfaced Water Bound Macadam Surfaces By Brushing With Wire Brushes For Removing Caked Mud Etc., Sweeping With Brooms And Finally Fanning The Cleaned Surface With Gunny Bags To Remove All Loose Dirt Etc. Complete All As Specified And As Directed. 15 Providing And Applying 2.5 Mm Thick Road Marking Strips ( Retro-Reflective ) Of Specified Shade / Colour Using Hot Thermoplastic Material By Fully / Semi-Automatic Thermoplastic Paint Applicator Machine Fitted With Profile Shoe, Glass Beads Dispenser, Propane Tank Heater And Profile Shoe Heater, Driven By Experienced Operator On Road Surface Including Cost Of Material, Labour, T & P, Cleaning The Road Surface Of All Dirt, Seals, Oil, Grease And Foreign Material Etc. Complete All As Specified And As Directed. 16 M & L For Continuous Brick Edging Using Old Size Bricks; With Width Equal To The Width Of The Brick; Laid Dry On End Vertically Complete All As Specified And As Directed. 17 Surface Dressing Not Exceeding 15 Cm Deep In Soft / Loose Soil Complete All As Specified And As Directed. 18 M & L For 15 Cm Thick ( Compacted Thickness ) Granular Sub Base Gsb With Coarse Aggregates Of Kankar Or Laterite Of Grading 2 ( 63 To 45 Mm Size ) Or Of Grading 3 ( 53 To 22.4 Mm Size ) , Spread, Rolled And Compacted To Required Gradient And Camber With An Equivalent Vibratory Roller Complete All As Specified And As Directed.

Sr No	CorrigendumDate	Corrignedum	CorrigendumType	NewSubmissionDate
1	20-Dec-2023	Bid Auto Extn Corrigendum	Bid Auto Extn Corrigendum	27-12-2023
2	27-Dec-2023	Bid Auto Extn Corrigendum	Bid Auto Extn Corrigendum	01-01-2024

INR 500 /-

INR 64000.0 /-

INR 32 Lakhs /-

Name of Work: SPECIAL REPAIR TO ROAD FROM JCO MESSAND INTERNAL ROAD AT MARIANI AT JORHAT MIL STN

Sl. No.	Item Description
1	S&F cat eye solar reflective type of metal body alloy of size 100x100x20mm with PAMA striplens reflector fixed with and including MS stud of suitable size as per manufacturer instructions complete all as specified and directed by the Engr-in-charge.
2	S & F solar road studs of size not less than 125X 125 X 25 mm made of weather resistance aluminium alloy and poly carbonate material electronically welded micro- prismatic lens with abrasion resistant coating as approved by the Engineer in charge. The cats eye shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35° ± 5° to base. The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM E: 809 as recommended in BS: 873 part 4 :1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge. The solar panel shall be high efficiency mono crystalline 2.5 V/60 m A and the battery shall be one Ni-mh type (1.2 V/1200 m Ah) high temp for backup of 36 hours full charging. The flash frequency shall be 60 ± 5 times per minute. Make- Model no 111 JUGNU of Dark Eye or equivalent makes as given in Appx B
3	Supply and fix plastic speed bump of size 50 mm (height) X 245 mm (width) X 350 mm (length), ABS block black and yellow & 02 no high reflective reflectors moulded in PMMA, fixed with nails and epoxy/thermoplastic adhesive (bas bumper and hole)with two different colourband pattern on road surfaceall as per manufacturers instructions and complying to guidelines issued by Min of Road Transport. etc. complete. Make- DA-1005 of Dark Eye or equivalent make as given in Appx B.
4	S & F metal tubular delineators (road way indicators) made out of ABS round body fitted with 2 Nos of 65 mm dia highly reflectivereflectors made out of PMMA and mounted on 45/50 mm mild steel pipe of 600 mm height duly power coated and thermo plastic elastomers 3 bands of green, red and yellow reflector radium tape of 25 mm wide strip with anti theft steel net for reflector protection including embedded 200 mm below ground level including excavation and PCC M15(Nominal Mix) with using 20 mm graded stone aggregate in foundationand making good surface complete all as specified and as directed.
5	Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area not exceeding 400 sqm, depth of pot hole exceeding 50 mm but not exceeding 100 mm including rolling over the broken surfaces using 8 to 10 tonnes power roller to required camber and gradient complete all as specified and as directed.
6	M & L for bituminous macadam not exceeding 75 mm thickness (compacted thickness) using hot mix plant and mechanical paver with 4% binder (paving grade bitumen VG-30 grade) content by weight of total mix, rolled and compacted with power roller 8 to 10 tonnes to required camber and gradient complete all as specified and as directed. Note :- (i) Bituminous macadam shall be laid using self propelled hydrostatic paver finisher and preparation of mix shall be using hot mix plant and transporting the mix in tipper. (ii) The exact bitumen content required shall be determined as per IRC 27: 2009. The adjustment in rate on MINUS side variation in quantity of bitumen if any shall be priced at the rate of ?55 per kg. No claim whatsoever shall be made for adjustment in plus side.
7	Preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and as directed.
8	M & L for applying evenly a tack coat with bituminous primer (paving grade bitumen VG-10 grade) @ 5 kg per 10 sq metres complete all as specified & as directed.
9	M & L for bituminous concrete 40 mm (compacted thickness) using graded crushed stone aggregate premixed with binder (paving grade bitumen VG-30 grade) @ 5.5% by weight of total mix & hydraulic lime/cement(OPC-43 Grade) filler, rolled and compacted to required camber and gradient complete all as specified and as directed. Note :- (i) Semi dense bituminous concrete shall be laid using self propelled hydrostatic paver finisher and preparation of mix shall be using hot mix plant and transporting the mix in tipper. (ii) The exact bitumen content required shall be determined following the Marshall Mix Design procedure contained in the Asphalt Institute Manual MS-2 (Sixth Edition) as referred in case 3.5.3 of IRC 111: 2009. The adjustment in rate on MINUS side variation in quantity of bitumen if any shall be priced at the rate of ?55 per kg. No claim whatsoever shall be made for adjustment in plus side.
10	Providing and applying 2.5 mm thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T & P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete all as specified and as directed.
11	Repair to potholes any depth, not exceeding 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc., cutting around edges to at least 25 mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal), rolled and compacted with power roller 8 to 10 tonnes to required gradient and camber complete all as specified and as directed.
12	M & L for15 cm thick (compacted thickness) WBM, in two layers of75mm thk each (each layer to be rolled and cosolidated separately) with coarse aggregates ofsand stone, flint or quartzite of grading 2 (63 to 45 mm size), spread, rolled and compacted to required gradient and camber with three wheel-power roller of 80 to 120 kN capacity or an equivalent vibratory roller complete all as specified and as directed.
13	M & L for applying primer on the surface of non-bituminous granular base course preparatory to the superimposition of bituminous treatment coat with cationic bitumen emulsion SS-1 grade at the rate of 10 kg per 10 Sqm of surface complete all as specified and as directed.
14	Preparing unsurfaced water bound macadam surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and as directed.
15	Providing and applying 2.5 mm thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T & P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete all as specified and as directed.
16	M & L for continuous brick edging using old size bricks; with width equal to the width of the brick; laid dry on end vertically complete all as specified and as directed.
17	Surface dressing not exceeding 15 cm deep in soft/ loose soil complete all as specified and as directed.
18	M & L for 15 cm thick (compacted thickness) granular sub base GSB with coarse aggregates of kankar or laterite of grading 2 (63 to 45 mm size) or of grading 3 (53 to 22.4 mm size), spread, rolled and compacted to required gradient and camber with an equivalent vibratory roller complete all as specified and as directed.