Installation & Energisation Of Dhaleekate (Ramagiri) R/L L.I. Projects Under R. Udayagiri Block In Gajapati District Out Of Bkvy (Ridf)-Xxix Grant2023-24
Tender Value
27.23 Lakhs
Estimated cost
Bid Submission
27 Nov 2023
0 days left
EMD
27230
Bank guarantee accepted
Document Fee
6000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
udayagiri → Odisha
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Installation & Energisation of DHALEEKATE (RAMAGIRI) R/L L.I. Projects under R. Udayagiri Block in Gajapati District out of BKVY (RIDF)-XXIX Grant2023-24
BOQ
| Sl. No. | Item Description |
| 1 | DHALEEKATE (RAMAGIRI) R/L |
| 2 | Earthwork in excavation of foundation in hard soil including dressing & levelling of bed within initial lead of 50mt. & lift of 1.5mtr etc complete as per the direction of the Engineer-incharge. |
| 3 | Filling in foundation & plinth with sand including watering & ramming etc complete as per the direction of the Engineer-incharge. |
| 4 | Cement concrete (1:4:8) with 4cm size h.g.c.b. metal of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc. complete as per the direction of the Engineer-incharge. |
| 5 | Cement concrete (1:2:4) with 12mm size black h.g.c.b.chips of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc complete as per the direction of the Engineer-incharge. |
| 6 | Cement concrete (1:2:4) for R.C.C. with 12mm size black h.g.c.b.chips of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc complete as per the direction of the Engineer-incharge. |
| 7 | Brick work with C.B. Brick 23cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerrance + 8% in cement mortar (1:6) in foundation & plinth etc. complete as per the Engineer-incharge. |
| 8 | Brick work with C.B. Brick 23cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerrance + 8% in cement mortar (1:6) inSUPER STRUCTURE etc. complete as per the Engineer-incharge. |
| 9 | 12mm cement plaster in cement mortar (1:6) finished smooth to brick work after racking out joints including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
| 10 | Rigid smooth a) R.C.C. floor and roof slabs, landings,balconies, projecting, sun shades and chajjas upto 4.3 mtr. height |
| 11 | (B) Rigid smooth centering & shuttering for R.C.C. works including false work & dismateling then after including cost of materials in ground floor complete an directed by the Engineer-incharge. |
| 12 | Labour charge for M.S. reinforcement for R.C.C. work including cutting, bending & typing the grills & placing in position including cost of binding wire 18 to 20 guage per Qntl. Including cost of HYSD Still Bar (FE 415/ FE 500) |
| 13 | Cement punning over plastering including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
| 14 | Filling the foundation and plinth with excavated material as directed by the Engineer-incharge. |
| 15 | Distempering two coats to walls with distermper of approved shade on new work to give an even shade including cost of distemper & labour etc. complete. |
| 16 | MS Pannel Door double leafed with MS frame overall size including frame of height 1.2mt x 1.98mt. width for door and shutter of 20 gauge CR sheet pannel as per approved size & specification etc. complete including cost of all materials fitting and fixing the door etc. complete as per the direction of the Engineer-incharge. |
| 17 | Earthwork in excavation of foundation in hard soil such as Hard stiff clay, stiff black cotton, hard red earth, shales, moorum ordinary gravels etc within 50m.Initial lead and 1.5m. Initial lift including rough dressing and levelling the bed and depositing the excavated materials within initial lead at nearby the worksite for reuse including breaking clods and stacking rubble for spreading and leveling as the case may be etc complete as per direction of the Engineer-in-charge(Excavation by machanical means 60% & manually 40%). |
| 18 | Labour Charges for Laying & Fitting &Transportation & carriage charges of materials (200mm HDPE Pipes) including loading, unloading and stacking & Overhead Chagres & Cess properly as per the direction of the Engineer-incharge. |
| 19 | Labour Charges for Laying & Fitting &Transportation & carriage charges of materials (160mm HDPE Pipes) including loading, unloading and stacking & Overhead Chagres & Cess properly as per the direction of the Engineer-incharge. |
| 20 | Filling F & P with excavated materials (Qty. same as item No.30 above) |
| 21 | Welding, laying and fitting of 100 / 150 mm Ø G.I. pipe |
| 22 | Cost of 45 mm dia steel Pipe of length 6 mtr |
| 23 | Cost of thick M.S Plate of 4 mm thick of size 1.20mtr x 0.90 mtr = 31.4kg*1.08=33.91 kg |
| 24 | Fitting, fixing, bracing & welding |
| 25 | Cost of Stickering & lettering with radium boarder |
| 26 | Electrical installation and energisationwith Pump house wiring andpanel wiring with all cost of materials and labour with minor fitting |
| 27 | Cost of Un-forsen item |
| 28 | Labour charges for delivery andfitting including fitting of priming Tee, sluice Valve, NR Valve, air release valve and riser Tee etc and installation Labour charges for installation of 15HP Motor including fitting & fixing of base frame, fitting & fixing suction and delivery pipe to motor, NR Valve, Foot Valve, Sluice Valve and other fitting materials including cutting, welding etc. complete as per the direction of the Engineer-incharge. |
| 29 | Cost of Three stage Photography, formation and handing over of Pani panchayat including cost of PTL Test |
| 30 | Cost of Tool kit Handing over to P.P |
| 31 | 15HP/11.20 KW Energy efficiency Monoblock pump set total head of 28 mtrs capable to discharge 1700 LPM with squirrel cage induction motor fitted with bronze impeller TB-2 of IS 318/1981, companion flanges & Class \"F\"insulation suitable for operation 415 volt +6%-15% 3 phase, 50Hz AC poweer supply suction/deliveery = 100mmx100mm with BEE Star rated energy efficiency Pump & as per IS-9079/2002 with overall efficiency 62 to 65% of reputed brand having wide dealership net work for easy availability of spares. confirming to IS specification (a) casing FC 200 as per IS 210/1978 (b) impeller: Bronze grade LTB-2 of IS 318/1981 including all cost, conveyance, cess etc complete but excluding cost of GST. |
| 32 | Control Panncel with Automatic Star Delta BCH make starter sheet steel enclosure suitable for operation of squirrel cage induction motor upto 15 HP with 25 Amp (AC-3) contactor at 400 volt +6% - 15%, 3 phase, 50 Hz, AC supply with suitable overload relay range 13.2 to 20 AMP. & No volt coil with electric pnemutic timer suitable for operation at voltage range of 300-440 volt including cost of transportation to site. The starter should provide dependable protection against overload and single phasing fitted with Volt meter, Ammter, MCB in complete sape incluing indicated lamp & should be of reputed brand of ISI specification having wide dealership network for easy availability of spares, including all cost , conveyance, cess etc complet but excluding cost of GST.. |
| 33 | Supplying 63 Amp. 415 volt T.P.Main Switch confirming to IS-4064 (PT-I & PT-II) with utilisation category AC-22 reputed brand of ISI specification including all cost, conveyance, cess etc complete but excluding cost of GST |
| 34 | 4 KVAR Power shunt capacitor with ISI mark of reputed approved brand of ISI marked incluing all cost , conveyance, cess etc complete but excluding cost of GST. |
| 35 | 3 x 16 sqmmPVC insulated (HD) tropoder armoured Electric bable with alluminum conductor conforming to IS: 7098 (Part-II) for use in 3 Phase power system of woring voltage upto & including 1100 volts at 50 Hz confirming to IS 7098 (Pt-II) of approved brand of ISI marked including all cost conveyance, cess etc complete but excluding cost of GST |
| 36 | Base frame for panel (size 0.40mx0.20m) made with 3\" size M.S. channel having suitable holes for fitting of panel Board, coloured with one coat of red oxide primer and two coats of smokes grey enamel paint & Base frame for motor (size 0.50mx0.27m) made with 3\" size M.S. channel having suitable holes for fittings of different size and make 3 phase centrifugal monoblock pump set from 10 H.P. to 15 H.P. coloured with one coat of red oxide primer & two coats of smoke grey enamel paint. |
| 37 | Motor hood size (0.45mx0.45mx0.60m) made with 18 SWG (cold rolled M.S.Sheet with one coat of red oxide primer and two coats of smoke gray / navey blue enamel n both side (inside & outside) suitable to cover centrifugal monoblock Pump Set from 10 HP to 15 HP and having provision for attachement with the groves on rear side of the pannel board. including all cost conveyance, cess etc complete but excluding cost of GST |
| 38 | 100 mm dia G.I. bend ( Medium Duty) conforming toIS No.1239(Part-II/1992) with ISI mark of reputed brand including all cost, conveyance, cess etc complete but excluding cost of GST |
| 39 | 100 mm dia G.I. flange( Medium Duty) conforming IS No.6392 / 1971 with ISI mark of reputed brand including all cost, conveyance, cess etc complete but excluding cost of GST |
| 40 | 100 mm dia G.I Nipple ( Meditm Duty ) with ISI mark of reputed brand including all cost, conveyance, cess tec complete but excluding cost of GST |
| 41 | 150 mm dia G.I. flange( Medium Duty) conforming IS No.6392 / 1971 with ISI mark of reputed brand including all cost, conveyance, cess etc complete but excluding cost of GST |
| 42 | 150 mmx100 mm G.I. Reducer |
| 43 | 150 mm dia G.I Socke t/ Nipple ( Meditm Duty ) with ISI mark of reputed brand including all cost, conveyance, cess tec complete but excluding cost of GST |
| 44 | 100 mm Ø nominal bore G.I. pipe having wall thickness 4.5 mm electrical resistance welded of medium class confirming to IS - 1239 (pt-1 of 2004) with latest ammendments screwed at both ends as perIS-554 with socketed at one end and the other protected with plastic threaded prtector including its transportation and unloading at LIPs site. The socket confirming to IS-1239 (pt-II/1992) with latest amendmewnts in random length of 4 to 7 mtrs. Each pipe should bear ISI certification & manufacturers name / Trade mark. (As per S/R 2022) |
| 45 | 150 mm Ø nominal bore G.I. pipe having wall thickness 4.5 mm electrical resistance welded of medium class confirming to IS - 1239 (pt-1 of 2004) with latest ammendments screwed at both ends as perIS-554 with socketed at one end and the other protected with plastic threaded prtector including its transportation and unloading at LIPs site. The socket confirming to IS-1239 (pt-II/1992) with latest amendmewnts in random length of 4 to 7 mtrs. Each pipe should bear ISI certification & manufacturers name / Trade mark. (As per S/R 2022) |
| 46 | 200 mm Ø MS / GI Flange medium duty as per IS specification |
| 47 | 200 mmx150 mm G.I./M.S. Reducer |
| 48 | Cost of 100mm dia C.I. Screw boss Foot valve of swing type friction less with single disc conforming to IS-4038/1979 of reputed brand with ISI mark of reputed company having wide dealership network including all cost, conveyance, cess etc complete but excluding cost of GST |
| 49 | 100mm Non-return valve C I double flanged swing type PN - 1.0 as per IS:5312 part-I with by-pass arrangement with ISI mark of reputed brand including all cost, conveyance, cess etc complete but excluding cost of GST ( As per S/R 2022) |
| 50 | Cost supplying of 50 mm Ø Kirloskar mark C.I.double Air release valve PN 1.6 with saddle and Raiser pipe conforming to IS 14845 (SI) makr including all cost, conveyance, cess etc complete but excluding cost of GST |
| 51 | 150mm dia C.I.Butterfly valve BS:5155/15: Kirloskar or equivalent mark 13095-CI MOC Lever operated Pn-1.0 with ISI mark of reputed including all cost, conveyance, cess etc complete but excluding cost of GST(As per S/R 2022) |
| 52 | Cost supplying of ISI marked High density polythelene (HDPE) pipes for water supply as per IS 4984/2016 in the following nominal diameter grades of materials pressure rating including the rates of ex-factory, transportation, pre & Post inspection, Cess etc complete but excluding the cost of GST(200mm dia PE 100-PN 6) |
| 53 | Cost supplying of ISI marked High density polythelene (HDPE) pipes for water supply as per IS 4984/2016 in the following nominal diameter grades of materials pressure rating including the rates of ex-factory, transportation, pre & Post inspection, Cess etc complete but excluding the cost of GST(200mm dia PE 80-PN 4) |
| 54 | Cost supplying of ISI marked High density polythelene (HDPE) pipes for water supply as per IS 4984/2016 in the following nominal diameter grades of materials pressure rating including the rates of ex-factory, transportation, pre & Post inspection, Cess etc complete but excluding the cost of GST(160mm dia PE 80-PN 4) |
| 55 | Cost of 200X160mm HDPEReducer alongwith 150mm Ø PVC tail piece |
| 56 | 160mm dia HDPE slipon flange |
| 57 | 200mm dia HDPE slipon flange |
| 58 | 200 mm x200 mm x160 mm Ø HDPE Spigot moulded reducing HDPETee (W.P. 10 kgf/cm2) |
| 59 | 201 mm x200 mm x200 mm Ø HDPE Spigot moulded reducing HDPETee (W.P. 10 kgf/cm2) |
| 60 | 160mm x160 mm x160 mm Ø HDPE Spigot moulded EqualHDPETee (W.P. 10 kgf/cm2) |
| 61 | 200mm dia HDPE end cap |
| 62 | 160mm dia HDPE end cap |
| 63 | 200mm HDPE Elbow Spicut Design 6 Kg |
| 64 | 160mm HDPE Elbow Spicut Design 6 Kg |
| 65 | 160mmX160mmX110 G.I Tee |
| 66 | Costof supplying of M.S Nut and bolt (1/2\" to 5/8 \") including all cost, conveyance, cess etc complete but excluding cost of GST ( As per S/R 2022) |
| 67 | Cost supplying of 3mm thick rubber insertion including all cost, conveyance, cess etc complete but excluding cost of GST ( As per S/R 2022) |
| 68 | Construction of 3 Phase 11KV HT line as per REC standard confirming to IE Rules 1956 with 300 kg 9 M long PSC pole with 55 Sqmm AAA Conductor average span 40mtr \"V\" Cross arm required No.of 11 KV T & C Disc polymer insulators in tension point & 11 KV Pin polymer insulators, Couping & Padding of Poles with all G.I.Channels Danger Board at each Pole, anti Climbing Devices, Stay set at Bending point & double stay at end point with 18mm G.I.H.T Stay, concreting of Stay with Anchor plate, guarding at Road crossings etc if required including cost of all materials, labour transportation, inspection & commissioning etc. complete. |
| 69 | Construction of 3 Phase L.T line as per REC standard confirming to RE rule 1956 with 300 kg 9 Mtr long PSC pole support in 0.33M span length with 3x35mm2 +1x25 mm2 LT, XLPE AB cable with coil earthing device, LT dead end clam, suspension clamp with GI hook, stay accessories such as wire insulator, clamp etc, nut bolts, alongwith concreting copping & padding of poles and stayset as per direction of Engineer in Chages. |
| 70 | Construction and erection of 11/0.4 KV, 63 KVA Double pole mounted Substation with 5mtrx3mtrx1.5mtr height mesonary toe wall / G.IFlat fencing boundary wall with flat with polymer insulator, L.T dist box with MCCB, Aluminim bus bar of single bay with kitkat fuse, sand filling and metal spearding with M.S.Grill gate, all channel matrials should be G.I. 7 nos earthing with chamber with 3 Mtr G.I pipe of 40mm dia with connecting of 25mmx5jmm G.I flat to all earthing including 63KVA BIS Leble-II Star rated Transformer confirming to RE Rules 1956, mounted on 2.44 Mtr. long structure, supported in 300 kg 9 mtr long PSC pole, transformer hard channel & top channelmade of 2.8 M long 100 x 50 x 6 mm G.I. Chalnnel , Transformer belting on 2.80 M Long 50mm x 50 x 5 mm G.I Angle, ( all REC SPN Std. F-3) with all accessories like 3 pole 11 KV GH Fuse (F-5) & A.B Switches (F-9) both mounted on 2.8 M long 75mm X 40mm X 6 mm G.I channel and supported by 1.0 M long 50 x 50 x 5 mm G.I Angle, with 3 No. 11 KV Lightening Arrestor and Danger board at each pole, anti climbing devices & all other necessary fitting i.e required size nuts bolts, brackets, cable, Cable sockets as per TPCOCL specification etc. including cost of all materials, labour, transportation complete with liasionging for testing inspection & commissioning as per specification of TPCODL etc complete. |
| 71 | Construction of boundary wall with brick work of size 12\"X10 \" with sand filling & metal spreading, fixing of iron grill gate etc. as per DISCOM specifi cation. |
| 72 | Electrical Earthing including all materials as per the direction of the Engineer-incharge. |
AI Tender Summary
Tender Timeline
Nov 18, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedNov 27, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedNov 28, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender