Tender For Provision Of 1 Mw Proof Top Solar Power Generation System Under Ge Af Sulur; 2 Material And Labour For Designing , Installing , Testing , Synchronization And Commissioning Of 1 Mwpon Grid Solar Roof Top Solar Power Generation System Comprising Of The Following:- Bis Certified Andmnre Almm Regisitered, Dcr Mono Crystalline Perchalf Cutcells Solar Pv Module / Panelssuitable For Installation On Roof Tops With Each Panel Having Capacity Not Less Than 540 Wpcomplete With Poly Carbonate Junction Boxes, Having Sufficient Number Of Fused Incomers And Outgoing Terminals ( Positive / Negative ) Suitable For 6 Ssqmm Cables And Connecting Cables Not Less Than 2.5 Sqmm Copper Conductor Multistranded ( Solar Cross Linked Poly Olefin Cables Double Insulated , Uv Resistant Halogen Free Low Smoke ) From Panel To Panel All As Specified And Directed.All Modules Will Have Minimum 25 Years Oem Linear Output Warranty. ( A ) Output Power ( Pmax ) 540Wp Or Above. ( B ) Module Efficiency: Not Less Than 90%C ) Number Of Cells: 72 Nos ( D ) Maximum System Voltage : 1500 Vdc ( E ) Application Class - A ( F ) Fire Class - A ( G ) Junction Box: Ip 67, 1.5 Kv 1000 Mm Length Cable. ( H ) Type Of Pv Cell: Mono Crystalline Silicon ( I ) Module Glass Transmission Shall Be > 93 % ( J ) Glass Thickness Shall Be Min 3.2 Mm ( K ) Each Pv Module Used In Any Solar Power Project Must Use A Rf Identification Tag ( L ) Bypass Diode For Optimizing Pv Out To Be Incorporated In Each Solar Module ( M ) Module Output: Mc Electronic Plug ( N ) Modules Only With Same Rating And Manufacturer Shall Be Connected. ( O ) Solar Module Must Have Iv Curve Test Report In Nabl Lab For The Speciifed Wattage ( P ) Design Including Civil / Electrical Infrastructure Metricularly Carried Out By Contractor As Per The Required Output Plant ( 1 Mw ) And Duly Vetted From Govt Approved Authority Of Nit / Iit And Approval By Garrison Engineer Before Execution At Site. 3 ( I ) Module Mounting Structure:- Design, Supply And Install Prefabricated Roof Top Solar Panel Mounting Structure Made Of Hot Deep Galvanized Steelangles / Channels / Flats Including Nuts / Bolts And Washers Suitable For Wind Resistance Upto 160 Mph Including Necessarypcc Foundations Of Grade Type B1 -1:2:4 Using 20 Mm Graded Stone Aggregateat Suitable Points To Provide For A Stable Robust Support All As Directed At Site All As Specified And Directed Including Designing Of Suitable Mounting Structure For Spv Module And Shall Be Provided As Per Design Cretirea Considering Live Load, Dead Load, Wind Load And As Per Condition Of Roof Slabs / Foundation Of Existing Bldgs Etc By A Approved Structural Engineer And Vetted By Nit / Iit And Approval By Garrison Engineer Before Execution At Site.A ) Structures Shall Be Of Flat-Plate Design Using Minimum Size Of C ( 75 X 40 X 5Mm ) Or L ( 55 X 55 X 5Mm ) Or I ( 60X 40X 4Mm ) Sections Or Higher Dimensions For Respective Sections.B ) Each Structure With Fixed Tilt Should Have A Tilt Angle As Per The Site Conditions To Take Maximum Insolation Which Will Be Approximately Equal To The Latitude Of The Location Facing True South With A North - South Orientation.C ) The Pv Module Mounting Structure Shall Have A Capacity To Withstand A Wind Velocity Of 160 Mph Unless Specified For Dedicated Requirementsd ) The Materials Used For Structures Shall Be Hot Dip Galvanized Mild Steel Conformed To Is 2062:1992.E ) The Minimum Thickness Of Galvanization For Hot Dip Galvanized Mild Steel Should Be At Least 80 Microns As Per Is 4759.F ) The Bolts, Nuts, Fasteners, And Clamps Used For Panel Mounting Shall Be Of Stainless-Steel Ss Grade.G ) Additional Structures / Frames For Required For The Installation Of Modules If Any Need To Be Provided By The Contractor.H ) The Structures Shall Be Designed To Allow Easy Replacement Of Any Module, Repairing And Cleaning Of Any Module.I ) The Structure Shall Be Designed To Withstand Operating Environmental Conditions For A Period Of Minimum 25 Years. And Shall Be Free From Corrosion While Installation.J ) Minimum Distance Between The Lower Level Of Pv Module And The Ground Shall Be 0.5M From The Ground Level.K ) The Structures Should Be Suitably Loaded With Reinforced Concrete Blocks Of Appropriate Weight Made Out Of M25 Concrete Mixture.L ) Photovoltaic Must Be Mounted On A Stable, Durable Structure That Can Support The Array And Withstand Wind, Rain, And Other Adverse Conditions. The Modules Will Be Fixed On Structures With Fixed Arrangement. ( M ) 100% Indigenous Company 4 Special Note :- ( 1 ) The Work Involves Provision Of Roof Top Panels Inall Maint Support Group Complex ( Msg ) Buildings, Contractor Should Visit The Site Before Quoting The Tender. ( 2 ) Suitability For Grid Connected System. ( 3 ) Pv Modules & Solar Cells Shall Be Made In India Andmakes And Manufacture By India Only. The Contractor Shall Submit All Required Documents . The Panel Should Be Of Latest Edition. ( 4 ) Power Warranty - 10 Year Warranty On 90% Of The Design Output And 25 Years Warranty On 80% Of The Design Output As Per Mnre Almm Registerd. . ( 5 ) Tangedco Registration Fees, All The Fees Related To Commissioning Should Be Borne By The Contractor. ( 6 ) Work Shall Be Executed As Per Tangedco & Ceig Norms. ( 7 ) All Materials Makes Shall Be Approved As Per Mnre, Tangedco. ( 8 ) Contractor Should Have Valid Teda Empanelment Cerificate. ( 9 ) No Drilling Is Allowed On The Roof Slabs. Existing Structures Shall Not Be Damaged, If Any Damage Shall Be Rectified By Contractor Without Any Extra Cost As Orginal As Directed By Engineer-In-Charge. ( 10 ) Each Pv Module Must Have Rfio Tag Wich Contain Name Of Manufacture Of Pv Module, Solar Cells& Month And Year Of Manufacturing, I-V Curve For Module, Peak Voltage, Im , Vm, Ff, Unique Serial No, Name Of Test Lab Issued Iec. ( 11 ) Liaisoning With Tangedco Authority For Obtaining Any Relevent Documents / Approved Of Installation Solar Power Plant To Grid From Tangedco For Smooth Functioning Shall Be Contractor Responsibility. ( 12 ) Feasiblity Clearence From State Electricity Board: Rate Quoted By Bidder Is Inclusive Charges For Feasbility Clearense And Liaison Work Regarding The Plant From Starting To Commissioning With Tangedco Will Be Done By The Contractor And Plant Will Be Taken Over After It Is Fully Functional Inculding Installation Of Energy Reading Meterand Certificed By Tangedco. ( 13 ) Standby Supply Shall Be Provided By Contractor Without Any Extra Cost To Department At The Time Of Synchronizing With Existing 11 Kv Sytem. ( 14 ) Technical Feasiblity Report Shall Be Obtained From Tangedco Before Starting Work In Ground. ( 15 ) Capacity Of Invertor Shall Be As Per Design Creteria And Approved By Garrison Engineer. ( 16 ) String Inverters Only To Be Use For This Project. ( 17 ) Solar Meter And Bi-Directional Meter : Supply Ht Net Meter / Bi-Directional Meter And Solar Meter To Deposit To Tangedco For Testing And Caliberation Thereafter Taken Back To Site For Instalation. Contractor Will Not Be Claim Extra Cost From Department For Carried Out Of Above Said Process. ( 18 ) Spv Panels And On Grid Inverter Should Be In Same Oem. ( 19 ) The Bidder Shall Carefully Desgin And Accommodate Requisite Numbers Of The Moudules In Each Buildings To Get The Design Output As Per Topography. Also Ensure Sufficient Circulation / Movement Area On The Roof Top For The Maintenance And Cleaning Purposeall Arround. ( 20 ) Neccessary Parafet Wall May Be Ensured O Each Building Gor The Proctection Of Men ( 21 ) Contractor Shall Maintain The Solar Plant By Employing 2 Well Experianced Technician In Handling Spv For 24 Hrs Upto 2 Years From The Date Of Completion Of Work . The Necessary Labour Wages Etc And Included In Quoted Rate. 5 Inspection Of Tangedco Electrical Inspector: Rate Quoted By Bidder Is Inclusive Electrical Inspectorates Inspection Charges To State Electricity Department By Sr Electrical Inspector. Contractor Is Bound To Arrange All The Documents / Inspection Reports / Test Sheets In Prescribed Format By Tangedco On Their Official Website & Pay Charges For Inspection After Successfully Installation Of The Solar Power Generation Systems. No Extra Payment Will Be Made In This Effects.Note : After Successfully Installation Of System, Contractor Will Submit Inspection Reports Duly Signed By Chief Electrical Inspector Of Tangedco To Mes For Buyback Agreement With Tangedco. If The Power Will Not Generated At A Correct Level / Limit , A Penalty Will Be Charged Against Contractor As Decided By Accepting Officer 6 General Notes : The Items Of Work Mentioned In Item Above Of This Schedule Shall Be Executed As Per Following:- ( A ) The Above Item Shall Be Quoted And Executed On Roof Top Based On Contractor’S Own Design On Performance Guarantee Basis. The Performance Guarantee Is Related To Achieving The 1 Mwp Generation With Specified Efficiency And Efficacies. The Contractor Shall Also Be Responsible For Desired Operational Efficiency And Desired Efficacies Of The System During Its Life Cycle Of Minimum 25 Years. ( B ) The Design Shall Be Got Vetted From Any One Of The Following Agencies ( Approved Agencies ) :- ( I ) National Institute Of Solar Energy ( Nise ) . ( Ii ) Sardar Swarn Singh National Institute Of Renewable Energy ( Iii ) Solar Energy Corporation Of India ( Seci ) . ( Iv ) The Indian Renewable Energy Development Agency ( C ) The Successful Contractor Shall Submit The Following Document Duly Vetted By Any One Of The Approved Agency, Within Four Weeks Of Placement Of Work Order For Approval Of Accepting Officer. ( I ) Design Calculations : The Tenderer Should Work Out Design Based On The Conditions Prevalent At Air Force Station Trivandrum Ground Situation And Site Conditions As Existing. ( Ii ) This Shall Be Self Contained And Self Explanatory Representation Of Layout Of Equipments And Sub-System. The Dimensioned Drawing Of The Site Of Work Clearly Marked With All Subsystems Components Etc Shall Be Submitted. ( Iii ) Schematic Diagram Of The Electrical System: This Shall Contain Specifications, Sizes, Current, Voltage And Fault Levels Rating Of All Cables, Switch Gears And Instrumentation & Control Systems And All Metering And Interlocking Etc. ( Iv ) The Installed Capacity Of Pv Panels Shall Be 10% More Than The Planned Capacity Keeping View Of Losses. ( V ) All The Documents / Technical Details Mentioned Above Duly Vetted As Specified Above Shall Be Approved By Accepting Officer Before Placing Final Order. The Ge May Approve The Document With Concurrence Of Accepting Officer As Submitted By Contractor Or May Suggest Modification / Alteration In Documents / Technical Specifications Duly Supported With Reasons For The Same. The Work Shall Be Executed Based On The Approval. ( Vi ) The Design Drawings And Other Technical Details Submitted By The Successful Contractor, Along With All Calculations, Drawings, Technical Write Ups Etc Shall Become Department Property. Department May Use These Subsequently As Deemed Necessary. The Contractor Shall Have No Claim On These Document And Their Subsequent Use By The Department. ( D ) During Execution The Contractor Must Engage Experienced Engineer In The Same Field For Supervision, Monitoring And Execution. The Contractorshall Certify That Execution Of The Work Has Been Done Satisfactorily.The Contractor Shall Certify That The Work Has Been Executed In Accordance With Vetted And Approved Design. All Cost And Charges For Engagement Of Consultant Shall Be Born By The Contractor. ( E ) Department Will Give Completion Of The Work To The Contractor Only On The Basis Of Basis Of Completion Report Submitted By The Consultant Engaged By The Contractor For Design. ( F ) After Execution Of Project The Contractors Will Verify Generation Of Electricity As Per Vetted Design In The Pvsyst / Pvsol Report Submitted And Connection Of The Same With Existing Power Supply Network. ( G ) The Contractor Shall Ensure Suitable Arrangement For Solar Pv Panels. 7 Design , Supply , Install Testing And Commissioning Of Data Logger With Online Monitoring Portal All As Specified And Directed With The Following Features:-.A ) Solar Irradiance: A Pyranometer / Solar Cell-Based Irradiation Sensor ( Along With Calibration Certificate ) Shall Be Provided, With The Sensor Mounted In The Plane Of The Array.B ) Temperature: Integrated Temp, Sensors For Measuring The Module Surface Temp., Inverter Inside Enclosure Temp, And Ambient Temp To Be Provided Complete With Readouts Integrated With The Data Logging System. ( C ) It Is Recommended That The Following Important Parameters Shall Be Accessible Through The Data Logging Facility.I ) Ac Voltageii ) Ac Output Currentiii ) Output Poweriv ) Energy In Kwhv ) Dc Input Voltagevi ) Dc Input Currentvii ) Temperatures ( C ) Viii ) Invertor Statusix ) Irradiationx ) Module Temperaturexi ) String Voltage & Current ( D ) All Communication And Control Cables As Per The Design. ( E ) Contractor Shall Install One Pc ( Latest Configurations ) With Printer And Other Requireed Accessories To Monitor Real Time Solar Data At A Designated Place As Directed By Ge. 8 Design , Supply, Install , Testing And Commisioning Bis Cerified And Bis Approved Ip65 Rated On Grid Inverter Suitable Output For 1 Mw, Natural Cooled, Suitable For Ambient Temperature Range 0 To 60 Deg Celsius, 50 / 60 Hertz Frequency, With Anti Islanding Features, Havingthree Phase Ac Output With Inbuilt Surge Protection Devices, Anti Reverse Power Controller, Fuse Protection, Dc / Ac Switches, Lcd Display For Generating Data, Wifi / Gprs Data Logger, Multiple Mppt For Optimum Generation, Wide Input Voltage Range All As Specified And Directed By Engineer In Charge.Note:- The On Grid Inverter Minimum Qty Of 05 Nos Or Morethan Is Considered In Quoted Rate As Per Design. 9 Minimum Requirement And Specification For On Grid Inverter:- ( A ) For Initializing The Inverters From The Sleep Mode, It Is Important That There Is Sufficient Sunlight And That The Utility Grid Is Available. Sufficient Sunlight In The Morning Is Needed To Provide Adequate Power To The Inverter So That It Could Start Up From The Over Night Sleep Mode. Availability Of The Grid Is Required To The Inverter As It Has Been Programmed To A Logic And A Pre-Set Window Of Grid Voltage And Frequency. If The Available Grid Has All These Qualities For Which The Inverter Is Designed, It Would Initialize The Main Out Put Contactor And Couple With The Grid And Start Evacuating The Power To The Grid It Is Coupled With. In Case The Grid Fails Due To Any Reason, The Inverter Should Come To Idle Mode Till The Grid Comes Back Again. Even During The Power Evacuation, If The Sun Light Falls Below The Desired Limit, Due To Clouds Etc., The Inverter Also Stops Working, Although The Grid Is Available, Till It Starts Getting The Desired Solar Power Required To Power The Inverter It Self. ( B ) If The Power Evacuation Goes On Till The Evening The Inverter Should Keep On Getting The Desired Solar Power Which Is In Excess Of The Power Needed To Operate The Inverter Itself. As Soon As It Attains The Power Which Is Just Sufficient To Run The Inverter, The Power Evacuation Stops And Only The Inverter Keeps Running Till The Power Drops Further Low Due To Decreasing Sunlight In The Evening, Resulting In The Inverter Going To Sleep Mode To Initialize Again Automatically The Next Morning. ( C ) A Record Shall Be Maintained With Input From Inverter In The Event Of Failure Of The Utility Grid Resulting In Inverter Going To Sleep Mode And Stop Generating Power. ( D ) The Pcu / Inverters Should Be Tested From The Mnre Approved Test Centros / Nabl / Bis / Iec Accredited Testing-Calibration Laboratories.+C50:C59c50:C61c50:C62c50:C61c50:C60c55c50:C57c50:C59c50:C60c50:C61 ( E ) Inverter Manfacturer Should Supplied And Installed Minimum Of 10 Mw Cumulative Capacity Of Inverter In Last 5 Years In India ( F ) Minimum Efficiency 98.5%. ( G ) The Dc To Ac Ratio Of 1.25 Is To Be Maintained At All Sites. ( For Eg. – For Dc Capacity Of 100 Kwp, The Ac Capacity Of Minimum 80 Kw Is To Be Maintained ) . ( H ) The Pcu Shall Have A Higher Degree Of Ingress Protection Of Ip 65 To Handle Robust Environment Conditions From Dust And Water Ingress Under Complete Outdoor Installations. ( I ) The Data Logger Should Possess The Feature Of Extracting The Data Externally With Open Protocols Like Modbus Tcp / Rtu. The Manufacturer Should Provide The Modbus Register Mapping File To Utilise This Feature ( J ) Specifications: ( I ) Nominal Voltage - 230V / 415V ( Ii ) Voltage Band - Between 80% And 110% Of V Nominal, Pollution Degree-Iv ( Ii ) Nominal Frequency - 50 Hz Saftey Class ( Iv ) Operating Frequency Range - 47.5 To 50.5 Hz ( V ) Waveform - Pure Sine Wave ( Vi ) Harmonics -Ac Side Total Harmonic Current Distortion < 3% 10 Minimum Requirement And Specification For On Grid Inverter ( Contd / -... ) :- ( Vii ) Ripple - Dc Voltage Ripple Content Shall Be Not More Than 1% ( Viii ) Casing Protection Levels - Degree Of Protection: Min Ip-65 ( Ix ) Operating Ambient Temp Range: -10 To + 60 Degree Celsius ( X ) Rh : 0-100% Non Condesing ( K ) Protections: ( I ) Reverse Polority Protection ( Ii ) Over Voltage: Both Input And Output ( Iii ) Over Current: Both Input And Output ( Iv ) Over / Under Grid Frequency ( V ) Over Temperature ( Vi ) Short Circuit ( Vii ) Lightning ( Viii ) Surge Voltage Induced At Output Due To External Source ( Ix ) Islanding ( X ) Ingress Protection - Ip 65 ( L ) Communication Interface : Rs485 / Rs232 / Wi-Fi ( With Or Without Usb ) ( M ) Synchronization: Photovoltaic System Must Be Equipped With A Grid Frequency Synchronization Device, If The System Is Using Synchronizer Inherently Built In To The Inverter Then No Separate Synchronizer Is Required ( N ) Dc Injection: Photovoltaic System Shall Not Inject Dc Current Greater Than 0.5% Of Full Rated Output At The Interconnection Point Or 1% Rated Inverter Output Current Into Distribution System Under Any Operating Conditions. ( O ) Power Factor: While The Output Of The Inverter Is Greater Than 50%, A Lagging Power Factor Greater Than 0.9 Shall Be Maintained. 11 Supply, Installation, Testing And Commissioning Dc Distribution Boards ( Arrey Junction Box ) , Ip 65, Suitable For Roof Top Solar Generation Systemof Rating Upto 250 Kw, 1500 Volts, 8 Incomer And 8 Outgoing With Dc Surge Protection Device 1500 V , Dc Fuse 30 A -8 Nosand Mcbs For Eight String Network. The Db Will Be Having Terminals Suitable For 4 / 6 Sqmm Copper Conductor Cables And The Enclosure For The Db Shall Be Made Of Frp / Abs With Ip65 / 66 Protection All As Specified And Directed By Engineer In Charge . Note : ( I ) Dc Panel Should Be Equipped With An Adequate Capacity, Dc Circuit Breaker Along With Control Circuit, Protection Relays, Fuses. ( Ii ) Dcdb Shall Have Sheet From Enclosure Of Dust And Vermin Proof, The Busbar / Cables Are To Be Made Of Copper Of Desired Size. Dcdb Shall Be Fabricated To Comply With Ip 65 Protection. 12 Supply , Installation, Testing And Commissioning Acdc Breaker, Outdoor Type, Ip 65 Protectedwith Following Specifications:-- Breaker- 415V, 4P, 400 Amp Mccb - 1 No ( Outgoing To Lt Panel ) - Ryb Indicator Lamps - Double Compression - Glands For Inputs, Double Compression Glands For Output-Enclosure Crca Powder Coated Pu Paint - All Input And Output Lugs ( Cu & Al Lugs As Per Cable Type ) 13 Desgin, Fabrication , Supply , Installation, And Commissioning Outdoor Type Solar Power Isolation Lt Panel Double Door ( Cpri Approved ) Ip65 Made Of Powder Coated Crca Sheet Steel 3.15 Mm With Necessary Floor Mounted Ms Channel Frame Made Of 100X100x10 Mm Duly Painted With One Coat Of Primer And Two Coats Of Synthetic Paint Including Necessary Pcc Foundation. The Panel Board Shall Have The Following Switchgear Enclosed Within :- ( A ) Aduijstial Thermal And Fixed Magnetic Setting Typemccb 4 Pole, 400 Amps, 36 Ka Rating – 05 Nos ( As Incoming From Ac Breakers ) B ) Aluminium Busbars Tpn 415 Volt, 2500 Amps Ratingc ) Elecric Draw Out Acb 4 Pole, 50 Ka 2500 Ampsrating – 02 Nos ( As Outgoing ) ( 01 Main And 01 Spare ) Lt, Air Circuit Breaker, Operational Voltage 660 Voilt, Insulation Voltage 1000 Volt, Ac, 50 Cycles, 3 Phase, ., 4 Pole, Electrical Draw Type, Rated Current Rating 2500 Amps And Of Breaking Capacity 50 Kaw With Quick Make, Quick Break, With Auto / Manual Operating Mechanisum, Microprocessor Based Over Current Stop Less Release And Static Trip Release, Adjustable Shourt Circuit Release, Earth Fault Realese With Shunt Trip With Indiction Under Voltage Release And Wired For Indicating Trip Healthy Circuit Ancillarey Switch Etc Complet Over Load Release Rating 2500 Ampd ) Energy Meter For Measuring Solar Energy Output With Cts And Pt Basede ) Cable Glands For Armoured Lt Cablesf ) Surge Protection Device , 4 Pole Type I And Type Ii Of Capacity , Iimp 8 Ka / Pole Max 32Ka ( G ) Muliti Function Microprocesscor Based Meter-01 Nos 14 ( H ) Led Type Pilot Indicuter Lamps Ryb Phases With Back-Up Fuses, Set Of Three-01 Set ( I ) The Lt Panel Board Shall Be Kept 450 Mm Above Ground Level, Mounted By Means Of Suitable Bolts Amd Nuts Grounted Into Paltform Of Pcc 1:3:6 Type C1, Using 20 Mmm Graded Stone Aggregate, Over Pcc Foundation Of 100Mm Thickness In Pcc 1:4:8 Type D2 Using 40Mm Graded Stone Aggregate, The Exposed Brick / Concert Surface Shall Be Remndered In Cm 1:4, 10 Mm Thick, Finished Fair And Even And Applied White Wash Three Coats. ( J ) Ammeter Digital Type 0-2500 Amps With Current Trasformer Of Suitable Capacity And Selector Switch-01 Set ( K ) Voltmeter Digital Type 0-500 Volt With Selector Switch-01 Set 15 Supply, Installation, Testing And Commissioning Of Ht Panel With Vacuum Circuit Breaker Panel Board, Factory Made, Outdoor Type, Metal Clad, Totally Enclosed, Free Standing Floor Mounting Type Ht 11 Kv, 3 Phase, 4 Wire, 50 Cycles, Ac Supply System Suitable For Housing Trolley Mounted Vacuum Circuit Breaker, Horizontal Isolation And Horizontal Draw Out Type, Cubicle Fabricated Out Of Crca Sheet 3.15 Mm Thick Weather, Dust And Vermin Proof, Epoxy Powder Coated, Of Ip-65 Protection Class Of Is-2147 With Self Contained Air Insulated Compartments For Bus Bars And Cable Boxes With Necessary Supports And 350 Mva, 800 Amp Rated Aluminium Bus Bar Including Cable Galleries, Interconnecting Bus-Bar Connection / Linkage, Suitable For Housing And Including Provision Of The Following Switch Gears Including All Pre-Wiring With Pvc Copper Conductor Cable Of Suitable Size, Nuts, Bolts And Washers And In Accordance With Is-13947 ( Part-1 ) 1993 & Is-8623 And All As Specified And Directed By Engineer-In-Charge. 16 Item No. 8 Shall Comprise The Following:- A. Fixed Spout Insulators Effectively Covered By Safety Shutters Which Automatically Open / Close During Draw In / Draw Out Operations.B. Phase Epoxy Base Isolating Spout Assemblies Complete With Isolating Contacts And A Pair Of Automatic Safety Shutter With Indivudual Locking System In Closed Position For Earthing / Maintenance Purpose.C. An Epoxy Interrupter Per Phase All As Per Manufacturer Design.D. Instrumentation Panel Shall Comprise The Following:- ( 1 ) Microprocessor Based 2 Element Over Current And 1 Element Earth Fault And High Set ( 2 ) Idmt Relay-01 No, Master Trip Relay - 01 No.Digital Type Frequency Meter. ( 3 ) Digital Type Ammeter ( 0-200 Amps ) With Selector Switches. ( 4 ) Resin Cast Current Transformers, 11 Kv, Ratio 200 / 100, 5 Amp, 15 Va Burden, Class 1 Accuracy For Metering And 15 Va / 5P 10 For Protection - 03 Nos. ( 5 ) Digital Type Voltmeter ( 0-15 Kv ) With Selector Switches. ( 6 ) Electrical Closing Coil 24 Volt Dc Operated - 01 Set 17 Supply, Installation, Testing And Comissioning Of Step Up Transformer Out Door Suitable For Plinth Mounting Complete With Standard Accessories Or Fittings Suitable For Inverter Voltage / 11 Kv ( At No Load ) Ac, 3 Phase, 50 Cycles, 4Wire, Capacity 1250 Kva Double Copper Wound, Immersed C R Go Core Typenaturely Coled, Built-Up With Class A Insulation Conforming - Is-1180 ( Part-1 ) 2014 ( Level-Iii ) Including Amendments As An The Date Of Receipt Of Tender Withfollowing Requirement:- ( A ) Contionus Rating : 1250 Kva ( B ) No Load Voltage Ration : 433 / 11Kv ( C ) Taping On Hv ) + / - 7.5%, + / - 5%. + / - 2.5 % ( D ) Phase And Frequency : 3 Phase & 50 Hz ( E ) Vector Group: As Per Design ( F ) Cooling: Onan ( G ) Type : OutdoorH ) Terminal Amangement: Hv Side: Quadfurcating Cable Box With 03 Nos Bushing Type Terminal For Connecting Ht Xlpe Cable And 01 No For Earthinglvside: Bus Duct ( I ) First Filling Of New And Unused Conforming To Is-335-1993 ( Fourth Revision ) Shall Be Marked, Filtered And Tested Upto 50 Kv Di Electric Strength At 2.5Mm Air Gap Between Testing Electrodes 18 Item No.9 Contd / -:- ( J ) Fittings: ( I ) Extermally Hand Operated Off - Circuit Tap Switch With Position Indicator And Locking Arrangement Device. ( Ii ) Conservator With Oil Gauge, Filling Hole With Plug And Drain Hole With Plug. ( Iii ) Undercarriage With Four Plain Rollers. ( Iv ) Lifting Lugs For Core. ( V ) Earthing Terminals. ( Vi ) 150Mm Oil Temperature Indicator With Alarm And Trip Contacts, ( Vii ) 150Mm Winding Temperature Indicator With Alarm And Trip Contacts. ( Viii ) Octc ( Off Circuit Tap Changer ) ( Ix ) Buchholtz Relay-01 No. ( X ) Top Filter Valve With Plug. ( Xi ) Rating Plate With Diagram Plate. ( Xii ) Lifting Lugs For Transformer. ( Xiii ) Oil-Filling Hole Cum Air Release Plug. ( Xiv ) Drain Valve Cum Sampling Valve. Thermometer Pockets. ( Xv ) Silica Breather. ( Xvi ) Marshalling Box With Double Window. 19 Supply, Fixing, Testing And Commissioning Uv Protected Xlpe / Xlpo Solar Grade Copper Cable Of Size, Pvc Insulated1 Core 4 Sqmm With Dc Connectors ( Male & Female ) Pair Mc4, 1.5 Kv Volts Rated All As Specified And Direcetd By Engineer In Charge. 20 Supply, Fixing, Testing And Commissioning Uv Protected Xlpe / Xlpo Solar Grade Copper Cable Of Size, Pvc Insulated1 Core 6 Sqmm With Dc Connectors ( Male & Female ) Pair Mc4, 1.5 Kv Volts Rated All As Specified And Direcetd By Engineer In Charge. 21 Supply And Laying High Density Polyethylene Pipes 50 Mm Dia ( Hdpe ) Of Pressure Rating 6 Kgf / Cm2 Fixed Complete To Walls, Ceilings Or In Floors Etc 22 Supply And Fixing Trunking Gi Cable Tray Of Size 150 Mm Width, 50Mm Height, Thickness 2Mm With Cover Of Size 155Mmwidth, 12Mm Height, 2Mm Thickness And Accessories ( Any Type Of Joint And Bends ) With Fittings ( Channel, Fasteners, Anchor Bolt ) Complete All As Specified And Directed. 23 Supply, Laying, Testing And Commissioning Cable Xlpe Insulated, Armoured Heavy Duty Electric Cable With Aluminium Conductor, 1100 Volts Grade, Cross-Sectional Area Of Size 300 Sq Mm 3.5Core With Consumables Like Lugs, Ferrules, Cable Ties, Upvc Tape, Upvc Saddle, Cable Clips Etc.Complete All As Specified And Directed. 24 Supply, Laying, Testing And Commissioning Cable Xlpe Insulated, Armoured Heavy Duty Electric Cable With Aluminium Conductor, 1100 Volts Grade, Cross-Sectional Area Of Size 1000 Sq Mm Single Core Hlogaen Free With Consumables Like Lugs, Ferrules, Cable Ties, Upvc Tape, Upvc Saddle, Cable Clips Etc.Complete All As Specified And Directed. 25 Supply, Laying, Testing And Commissioning Cable Xlpe Insulated , Screened, Pvc Bedded, Galvanized Steel Strip Or Wire Armoured, Electric Power Cables ( Heavy Duty ) 11000 Volts Grade With Stranded Aluminium Conductor Of Size 185 Sqmm , 3 Core Core And With Consumablescomplete All As Specified And Directed. 26 Supply And Laying Of Aluminium Bus Duct From Lt Panel To Transformer As Per The Current Rating Of Lt Panel And Tangedco Specificationcomplete All As Specified And Directed. 27 Material And Labour Earthing Withgiearth Plate Electrode Ofsize 60X60cmx6mm Thick Buried Directly In Ground To A Depth Not Less Than 2.25Mtr Deep Below Normal Ground Level With Top Edge Of The Earth Plate Not Less Than 1.5 Mtr Deep Below Normal Ground Level Connected To Gi Strip Of Size 32 X 6 Mm As Earthing Lead By Means Of Nuts, Bolts And Washers Of Steel After Welding Of Gi Strip To Earth Electrode To The Full Length Of Earth Plate, Gi Medium Grade Pipe 40 Mm Bore Protection Pipe Upto Test Point, 20Mm Dia Gi Light Grade Watering Pipe With Funnel And Wire Mesh, Rcc Pit Cover Of Size 300X300x40mm Reinforced With Xpm Having Weight Not Less Than 4Kg / Sqmm Including 6Mm Thick Ms Bar Handle Made To Shape, Pcc Pit With 1:3:6 Type C1 With Angle Iron Frame Made Of Angle Iron Of Size 40X40x4mm, Adequate Qty Of Charcoal Dust And Salt Layers All Around The Earth Plate, Earth Work In Any Type Of Soil, All As Required At Site Complete All As Specified In Plate No 3 Of Ssr Part-I And All As Specified Orindicatedincludingtesting On Completion. 28 Earth Continuity Conductor Or Main Earthing Lead Fixed To Wall On Batten Or Recess Or Chases Or Buried In Ground Or Drawn In Conduit / Pipe Or Fixed To Poles Or Any Other Indicated Situation For Loop Earthing Etc. As Required 32 X 6 Mm Galvanised Iron Strip , Strip Will Be Fixed By Epoxy Insulators Without Making Hole At The Distance Of 60 Cm From Each Othercomplete All As Specified And Directed. Note - Earth Strip Shall Be Connected By Welding Only. 29 Material And Labour For Air Termination Rods With 40Mm Light Grade Pipe 1.5Meters Long, With 300 Mm Long, 6Mm Dia Copper Rod Clamped At One End And Base Of Pipe Embedded In Pcc Foundation Of Grade 1:3:6 Of 20 Mm Grade Aggregate On Roof Slabcomplete All As Specified And Directed. 30 Test Point Terminal Block Made Of Gun Metal Or Phosphor Bronze Size 75Mmx75mmx 25 Mm Drilled And Scewed Including 3 Nos 8 Mm Dia 25 Mm Long Hexagonal Head Screws Complete All As Specified And As Directed. 31 Excavation In Trenches Not Exc 1.5 M Wide And Not Exc 1.5 Min Depth For Laying Of Ug Cableand Getting Out In Hard Soilcomplete All As Specified And Directed.Note- Excavation Shall Be Done By Manual Process. 32 Returning, Filling, Including Spreading, Levelling, Watering And Well Ramming In Layers Not Exc 25 Cm Thick In Any Type Of Exacavated Soilcomplete All As Specified And Directed. 33 Removing Excavated Material To A Distance Not Exc 50 M And Deposited Where As Directed At A Level Not Exc 1.5 M Above The Starting Pointcomplete All As Specified And Directed. 34 Supplying And Laying Un-Reinforced Precast Concrete Cable Cover, Class Lv, Type 1, Isi Marked, Factory Manufactured, Size 250 Mm X 150Mm X 40Mm Complete All As Specified And Directed. 35 Supply And Spread Natural Riddled Soil In Trenches For Cushioning And Covering To Cable Complete All As Specified And Directed.Note: ( I ) Naturalsoil Shall Be Riddled By Using Sieve To Separate Composite Particles Etc As Per Is And Refilling In Trenches Before Laying Of Cable 8 Cm And 15Cm After Laying Of Cable. This Is Then Gently Punned Down To A Depth Of 10Cm Above The Top Of Upper-Most Cable. ( Ii ) For The Purpose Of Measurement Only Punned Thickness Only Will Be Considered For Payment. 36 Supply And Laying High Density Polyethylene Pipes ( Hdpe ) Of 32 Mm Dia Pressure Rating 6 Kgf / Cm2 Laid In Trenches And Fixed On Polescomplete All As Specified And Directed. 37 Material And Labour Cable Jointing Kit For 11 Kv ( Earthed ) Grade Cable For Indoor Termination Heat Shrink Type Joint Complete With Jointing Material And Accessories Suitable For 3 Core Xlpe Armoured Aluminium Conductor Cable Of Size 120 Sqmm To 185 Sqmmcomplete All As Specified And Directed. 38 M & L For Lt Cable Route Indicator With A Welded / Riveted Disc Of 4 Inch Dia And Engraved With Cable Route Marker Welded To Angle Iron 40 X 40 X4 Mm Thick Fixed In Ground With In And Incl Pcc 1:3:6 Type C1 Using 20Mm Graded Aggregate Including Necessary Earth Work, Form Work Etc Complete All As Specified And Directed. 39 Supply And Fix Fire Extinguisher Abc Type Of Capacity 4 Kg Complete All As Specified And Directed. 40 Supply And Fix Fire Bucket Stand With Buckets -03 Nos Complete All As Specified And Directed. 41 Supply And Fix Rubber Mat Of Size 2 Mtr X 1 Mtr Of Thickness 2 Mm, Isi Marked Complete All As Specified And Directed. 42 Desgin And Supply Of Backup Source For Scada & Internal Lighting As Per Design ( Min 5 Kva With 3 Hours Back Up ) Complete All As Specified And Directed. 43 External Water Supply 44 Supply And Fixing Of Hdpe Rotational Moulded Polyethylene Water Storage Tanks Capacity 2000 Ltr ( Cylindericval Vertical With Closed Top ) Hostied And Fixed In Positionas Per Isi Maskedis 12701 / 1996 All As Specified In Ssr Part -Icomplete All As Specified And Directed. 45 Supply And Fixing Of Solar Module Water Cleaning System Kit For The 1000 Kw Solar Power Plant System For Complete Proposed Buildings. Complete Design Ofthe Cleaning Systemsduly Vetted By Iit / Nit For The Approval Of Garrison Engineer Before Execation At Site. Complete Bill Of Material, Specfication And Necessary Certificates If Any Shall Be Submitted By The Bidder Duly Signedin Duplicatedbefore Exicution Of The Work.The Design Should Comply With The Following Minimum Requirements : - ( A ) Supply & Fixing Of Spraying Nozzle / Sprinkler System With Following Specifications:-Material : Abs ( Plastic ) - Working Angle - 0 To 90 Deg- Discharge: 5 To 7 Lpm- Pressure: 1 Kg / Sq.Cm To 2 Kg / Sq.Cm Qty :- As Per Desgin ( B ) Supply & Fixing Of Automatic Valve With Following Specifications;- Working Medium: Water- Motion Pattern: Diaphgram Type- Electrom Maganetic Actuator, - Working Pressure 0 To 10 Bar- Working Medium Temperature: 0 To 85 Deg C- Material Of Body: Nv 66 / Cf 8 / Cf 8M Qty :- As Per Desgin ( C ) Supply & Fixing Of Screen Filter With Following Specifications;- Maximum Working Pressure : 10 Kg / Sq.Com- Range Of Water Flow: 5 - 8 Cum / Hour- Screen Cartridge: Double Screen 30 / 120 Mesh-Filtration Surface Area: 12P Sq.Cm Qty :- As Per Desgin 46 Item No. 36 Contd / -.. ( D ) Supply & Fixing Of Auto Controller With Following Specifications;- Single Phase Smps - 3A / 12Vdc Output- Control Card-Qty : Based On Design ( E ) Supply & Fixing Of Submersible Pump With Following Specifications;- Stator : Ss 304- Hp / Kw : Based On Desgin- Phase : Single / Three - Rpm : 2900 - Current 7.5 Amp-Qty : Based On Designnote : All The Above Are Minimum Essensial Requirements. Contractor Has To Submit Detailed Design Along With Layout And Details Of All Componets And Bifercation Details Of Rates For Each Component Considered In The Quoted Rates As Per Design. The Quoted Rates Are Deemed To Be Included With Rates Of All The Components As Per Desing Where Not Mensioned Here In Before.Nothing Extra Will Be Payable On This Account. 47 Unplasticiscd Pvc Pipes ( Sch 80 ) Hsn Code : 3917 Of Pressure Rating 10 Kgf / Cm2 , Class A Laid In Trenches Of The Following Sizes, 48 ( A ) 110 Mm Dia 49 ( B ) 75 Mm Dia 50 ( C ) 50Mm Dia 51 ( D ) 40 Mm Dia 52 ( E ) 32 Mm Dia 53 Supply & Fix Upvc Ball Valve, 100 Mm Dia 54 Supply & Fix Upvc Ball Valve, 75 Mm Dia 55 Supply And Fix Ppr Gate Valves ( Brass Insert ) Of 50 Mm Bore. 56 Supply And Fix Ppr Gate Valves ( Brass Insert ) Of 40 Mm Bore. 57 Supply And Fix Ppr Gate Valves ( Brass Insert ) Of 32 Mm Bore. 58 Supply And Fixing Of Wet Type Submersible Pressure Pump Capacity Of 5 Hp ( 1W+ 1Sb ) With Suitable Panel Board As Per Is 8034 / 1989 And Is 9283 / 1995 Suitable To Pump With Dry Run Prvententor Etc. Complete As Per Isi Standered Specfication 59 Supply, Install, Testing And Commissioning Of Outdoor Type Factory Fabricated Motor Starter Panel Suitable For 3 Phase 415V, 50Hz System Made Out Of Crca Sheet 3.15 Mm With Suitable Neoprene Rubber Gasket To Make It Completely, Dust And Vermin Proof, Front Openable Type Alongwith Locking Arrangement Having Angle Iron Base Frame And Legs Of Suitable Size, Pcc ( 1:3:6 ) Bedding For Grouting Of Base Including Dismantling And Taking Out Old Unserviceable Panel, Complete All As Specified And Directed. The Panel Shall Comprise The Following Accessories And Specifications :- ( A ) Mccb 4 Pole, 63 Amps, 16 Ka - 01 No ( Incoming ) ( B ) Dolstarter Suitable For 5 Hp Centrufugal Pump Set Incl Timer- 02 Set ( C ) Motor Protection Relay - 01 Set ( D ) Single Phase Preventor - 01 Set ( E ) Phase Indicating Led Lamps Ryb - 01 Set ( F ) Panel Mounted Multifunction Meter Including Cts Of Suitable Ratio - 01 Set ( G ) On / Off Push Button Alongwith Indication Light - 01 Set ( H ) Electrolytic High Conductivity Insulated Copper Bus Bar Of Suitable Capacity - 01 Set ( J ) Pump 1 & 2 Selector Switch ( K ) Auto Mannual Selector Switch -01 No ( I ) Earthing Terminals - 02 Nos 60 S&F Of 80 Mm Nrv For Water Pipe Line Type - Swing Type Flange End Bolted Cover Moc - Ci Complete All As Specified And Directed. 61 S&F Of Pressure Gauge 4 Dial - Ss Glycerine;Type - Diaphragm;Complete All As Specified And Directed. 62 Supply, Laying And Testing Xlpe Insulated Screened, Pvc Bedded, Galvanized Steel Strip Or Wire Armoured, Electric Power Cables ( Heavy Duty ) 1100 Volts Grade With Stranded Aluminium Conductor Of Size 50 Sq Mm 3.5 Corecomplete All As Specified And Directed. 63 Construction Of Valve Chamber Of Followinginternal Size Suitable For Sluice Valve, With 150 Mm Thick Pcc 1:4:8, Type D2, Using 40Mm Graded Aggregate For Foundation, 200 Mm Thick Brickwork With Old Size Fly Ash Bricks In Cement Mortar 1:6, 40 Mm Thick Pcc, 1:2:4, Type B1, Using 20Mm Graded Aggregate Coping, Rendering In Cm 1:4, 15 Mm Thick Including Provision Of Mild Steel Sheet Cover 3 Mm Thick With 40 X 40 X 6 Mm Size Angle Iron Frame Work Embedded In Concrete With Suitable Hinges And Locking Arrangements Including Two Coat Of Synthetic Enamel Black Paint Over A Coat Of Red Oxide Zinc Chrome Primer To Steel Surfaces And Includingnecessary Earth Work Excavation In Any Type Of Soil Etc., Removal Of Surplus Soil Off The Premises Complete All As Specified. ( A ) 900X 900 X 900Mm Type C 64 ( B ) 600 X 600 X 600 Mm Type B 65 External Electric Supply 66 S&F 6 Sqmm Multistranded Copper Conductor, 3 Core Pvc Insulated And Sheathed Copper Screen Protected 1100 Volts Grade Submersible Flat Cable Fixed To Column Pipes With Suitable Clamps &Jointing Material Complete Including Disconnecting & Taking Out Old Unserviceable Cablecomplete All As Specified And Directed. 67 Material And Labour Cross Arms, Bracings, Supports, Clamps And Back Plates Fabricated From Structural Steel Sections Including Nuts, Bolts, Washers, Welding, Bending Cold Or Hot, Drilling Holes For Bolts, In Any Shapeor Size As Indicated Or Directed And Incluse Of One Primer Coad, One Under Coat And One Finhing Coat Of Paint All As Specified And Directed By Engineer-In-Charge. 68 Supply And Fixing 80 Watts Led Floodlight With Fittings On The Roof Of Solar Module Installed Floorscomplete All As Specified And Directed. 69 Point Wiring Complete With 1.5 Sqmm Single Core Pvc Insulated Frls Unsheathed Cable 1100 Volts Grade With Multi Stranded Copper Conductor Drawn Thr Including Non Metallic Rigid Pvc Conduit With All Conduit Accessories Not Less Than 20Mm Dia ( Concealed ) And Including Provision Of 1.5 Sqmm Pvc Insulat Unsheathed Cable Frls As Earth Continuity Conductor, Metal Flush Box And White Cover Plate With Frame For Suitable Number Of Modules Flush Mo Concealed In Walls With Suitable Screws For Housing The Switches, Socket Outlets, Fan Regulators Etc, Complete All As Specified And As Directed. 70 Switch Piano, One Way, 6 Amps, For One Module Complete All As Specified And As Directed. 71 Supply And Lay Gi Pipe 80 Mm Bore Medium Grade For Cable Protection Completeall As Specified And As Dierced. 72 Cutting Existing Road / Pcc / Drain For Laying Of Di / Gi Or Any Typeof Pipe Including Necessary Earthwork, Excavation Exc 600Mm Depth But Not Exc 1Mtr Depth, Wide 800Mm Including Making Existing Surface With Pcc 1:2:4 Type B1 Using 20Mm Aggregate Thickness Of Concrete Is 150Mmcomplete All As Specified And Directed. 73 Security Fencing With Wicket Gate 74 Excavating In Post Holes ( Or Similar Holes ) Each N Exc 0.5 Cum, Getting Out, Returning, Filling In And Ramming Earth Or Broken Rubble Mixed With Earth Around, In Layers Not Exceeding 25Cm In Hard / Dense Soil, Watering, And Removing Surplus Soil To A Distance N Exc 50 M And Making Good Surface Complete All As Specified And Directed. 75 M&L For Pcc 1:3:6 Type C-2 Using 40 Mm Graded Stone Agg As In Foundation Filling And Mass Concrete Complete All As Specified And Directed. 76 S & F Mild Steel Con-Forming To Fe-290 Gde E-165 Qualitya As In Angle Post Or Struts In Fencing Fixed Independently Including Cutting And Bending To Shappe As Directed, Drilling Holes, Notching For Wire, Flat Iron Fillet For Securing Wire Mesh Etc Complete All As Specified And Directed. 77 M&L Mild Steel Structural Framed Work Such As Grills, Gratings Etc., With Ends Of Bars Shouldered And / Or Riveted, Or Forget Into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework Of Water Tanks And Similar Work Conforming To Fe-290 Gde E-165 Complete All As Specified And Directed 78 S & F Mild Steel Screw Bolts ( Machine Made ) With Hexagonal Or Square Heads At One End And Screwed The Other, Or Screwed Both Ends, Each Screwed End To Be Fitted With Washers And One Hexagonal Or Squareexc 5 Cm Not Exceeding 10Cm Long And 5 To 10 Mm Dia Complete All As Specified And Directed. 79 Supply Only Chain Link Ms Galvanised Fencing Wire Made With 3Mm Dia Gi Wire & 100X100mm Mesh Size All As Specifiedand Directed 80 Fixing Only Chain Link Fencing Including Line Wires, Any Mesh, Size And Type To Any Type Of Standards, Rails, Straining Bolts, Etc. Including Provission Of Binding Wire Complete All As Specified And Directed. 81 Mild Steel Round Bars 10 Mm Dia And Over As In Strengthening Bars For Chainlink Fencing Conforming To Fe-290 Gde E-165Complete All As Specified And Directed. 82 M & L For Applying Two Coats Of Synthetic Enamel Paint Over A Coat Of Red Oxide Primer Including Preparation Of New Steel Surfaces Of Any Description Exc 10 Cm Girth Or Width Complete All As Specified And Directed. 83 M & L For Applying Two Coats Of Synthetic Enamel Paint Over A Coat Of Red Oxide Primer Including Preparation Of New Steel Surfaces Of Any Description Not Exc 10 Cm Girth Or Width Complete All As Specified And Directed. 84 Foot Path 85 Surface Excavation N Exc 30 Cm Deep And Averaging 15 Cm Deep And Getting Out In Hard / Dense Soicomplete All As Specified And Directed. 86 M&L For Hard Core Of Gauge Not Exc 63 Mm Size Depositing Spreading , Leveling Watering And Well Ramming With Broken Stone Boulders / Stone Specifiedcomplete All As Specified And Directed. 87 M&L 100 Mm Thick Pcc 1:4:8 Type D-2Using 40 Mm Graded Stone Aggregate As In Floors Surface Finished Cement Surface All As Specified And Directed. 88 M&L Sand Filling Under Floor Or In Foundation Including Watering And Consolidation And All As Specified And Directed. 89 M &Lmachine Pressed Precast Conctete Interlocking Paver Block Any Shape And Size Confirming To Is 15658-2006 Of 80 Mmthickness M-35Grade With Grey Cement & Pigment All As Specified And Directed. 90 Plain Cement Concrete 1:3:6 Type C1 Using 20Mm Graded Stone Aggregate As In Kerbs, Coping Etc Including Necessaty Formworkcomplete All As Specified And Directed. 91 Removing Excavated Soil In Hard / Dense Soil Exc 1.50 Km And Not Exc 5.00 Km Out Side The Campus Including Loading And Unloading Etc., Where Responsibility Regarding Place Of Deposition And Permission From All Authorities Etc., In This Regard Will Be Of Contractor Andcomplete All As Specified And Directed. 92 Mild Steel Ladder 93 Mild Steel Base Plates & Cleats ( Chequred Or Plain ) Channels, Squred Cut Or Notched ( Ordinary And Counter Sunk ) Forming Holes For Nuts And Bolt Or Welded Attachment Including Anchor Nuts & Bolts 20Mm Dia 400Mm Long ( Machine Made ) With Hexagonal Or Squre Heads Conforming To Fe-410- W ( Gde E-250 ) Quality- A Complete All As Specified And As Directed. 94 M&L Plain Cement Concrete, Type B2, 1:2:4 In Foundation Filling And Mass Concrete Complete All As Specified And Directed. 95 M & L For Two Coats Of Black Bituminous Paintof Any Description Wood, Steel, Iron, Concrete, Brick, Stone, Etc., Exceeding 10Cm In Width Or Girth Including Preparation Of New Steel Surfcaes Complete All As Specified And Directed. 96 Ug Sump Of Capacity 20000 Litres 97 Provn Of Rcc Ug Sump Of Capacity 20000 Litres Complete All As Specified And As Directed. 98 Total Of Schedule A
