|
| 1 | NOTES :The bidders/contractorsare advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.W/S PORTION |
| 2 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc. or for shafts, wells, cess pits, manholes, pier holes etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out as in soft/loose soil. |
| 3 | Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level n. exc. 1.50 m above the starting point. |
| 4 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil. |
| 5 | Materials and Labour for galvanized steel tubing, medium grade, 100 mm bore with all fittings, laid in trenches, and including taking up old GI pipe complete all as specified and as directed. |
| 6 | Materials and Labour for galvanized steel tubing, medium grade, 80 mm bore with all fittings, laid in trenches, and including taking up old GI pipe complete all as specified and as directed. |
| 7 | Materials and Labour for galvanized steel tubing, medium grade, 50 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor and including taking up old GI pipe complete all as specified and as directed. |
| 8 | Materials and Labour for galvanized steel tubing, medium grade, 40 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, and including taking up old GI pipe complete all as specified and as directed. |
| 9 | Materials and Labour for galvanized steel tubing, medium grade, 25 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, and including taking up old GI pipe complete all as specified and as directed. |
| 10 | Materials and Labour for galvanized steel tubing, medium grade, 20 mm bore with all fittings, laid in trenches, and including taking up old GI pipe complete all as specified and as directed.Note for item no 5 & 10- All fitting & fixture such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector, holding clampshall be provide as per site requiredment and same shall deem to be included in quoted rate. |
| 11 | Supply, laying and jointing of ductile iron pipes with spigot and socket ends suitable for push on rubber joint centrifugally cast, class (K-7), iner side cement lining and outer side black bitumen coating andany length, laid in trenches of 100mm bore pipe including push on rubber (EPDM) ring with ISI markedand including taking up old pipe complete all as specified and as directed. |
| 12 | Supply,laying& fixingin repair of ductile Iron pipe fittingssutable for flange,spigot & socket pipe complete all as specified and directed. |
| 13 | Supply,laying& fixingin repair of cast iron fittings for spigot and socketed cast iron pipes for water mains upto 150 mm bore,such as Bends (any type, radius and angle) tapers any type, (straight, bend, increasing,decreasing or double socket etc.) Tee pieces single branch. \"Y\" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs, complete all as specified and directed. |
| 14 | Material and labour for Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20 mm bore and including taking up old valve complete all as specified and as directed. |
| 15 | Material and labour for Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 25mm boreand including taking up old valve complete all as specified and as directed. |
| 16 | Material and labour for Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 40mm boreand including taking up old valve complete all as specified and as directed. |
| 17 | Material and labour for Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 50mm boreand including taking up old valve complete all as specified and as directed. |
| 18 | Supply and fixing in repairs, cast iron double flanged ( Wafer Type), lever operated, butterfly valve,size 100 mm, PN 1.6, Class 300, with stainless steel shaft, ISI Marked (IS-13095), includingMS bolts, nuts, washers and a pair of rubber gasket ISI markand including taking up old valve complete all as specified and as directed. |
| 19 | Supply and fixing in repairs, cast iron double flanged ( Wafer Type), lever operated, butterfly valve,size 80 mm, PN 1.6, Class 300, with stainless steel shaft, ISI Marked (IS-13095), includingMS bolts, nuts, washers and a pair of rubber gasket ISI markand including taking up old valve complete all as specified and as directed. |
| 20 | Repairs/ servicing to sluice valve by taking out unserviceable spindle along with wornout check nuts from the sluice valve of 150 mm bore after removing the top cover and stuffing box of sluice valve spindle, and refixing with new brass spindle with check nut, gland packing, gasket, replacing of rusted unserviceable nuts/ bolts/ washers with SS with new nuts, bolts, gaskets etc for arresting all leakages/ smooth operation complete all as specified and directed. |
| 21 | Repairs/ servicing to sluice valve by taking out unserviceable spindle along with wornout check nuts from the sluice valve of 100 mm bore after removing the top cover and stuffing box of sluice valve spindle, and refixing with new brass spindle with check nut, gland packing, gasket, replacing of rusted unserviceable nuts/ bolts/ washers with SS with new nuts, bolts, gaskets etc for arresting all leakages/ smooth operation complete all as specified and directed. |
| 22 | Repairs/ servicing to sluice valve by taking out unserviceable spindle along with wornout check nuts from the sluice valve of 80 mm bore after removing the top cover and stuffing box of sluice valve spindle, and refixing with new brass spindle with check nut, gland packing, gasket, replacing of rusted unserviceable nuts/ bolts/ washers with SS with new nuts, bolts, gaskets etc for arresting all leakages/ smooth operation complete all as specified and directed.Note for item no __ to___ :-Brass Spindle along with check nuts and nuts/ bolts shall be measured and paid under this items. |
| 23 | S & F for 100 mm dia CI Non Return valve both side flanged with SS spindle PN 1.6incl in repair accessories after taking down old unserviceable valve. |
| 24 | S & F for 80 mm dia CI Non Return valve both side flanged with SS spindle PN 1.6incl in repair accessories after taking down old unserviceable valve. |
| 25 | Materials and Labour for, joint with rubber or fibre board gasket for galvanized steelflanged pipes and fittings, 80 mm bore,including provision of bolts, nuts, washers and white lead or mineral oil,after taking down existing joint, complete all as specified and directed. |
| 26 | Materials and Labour for, joint with rubber or fibre board gasket for galvanized steelflanged pipes and fittings, 100 mm bore,including provision of bolts, nuts, washers and white lead or mineral oil, after taking down existing joint,complete all as specified and directed. |
| 27 | Materials and Labour for, joint with rubber or fibre board gasket for galvanized steelflanged pipes and fittings, 300mm bore and above, including provision of bolts, nuts, washers and white lead or mineral oil, after taking down existing joint, complete all as specified and directed. |
| 28 | Materials and Labour for, joint with rubber or fibre board gasket for galvanized steelflanged pipes and fittings, 150 mm bore,including provision of bolts, nuts, washers and white lead or mineral oil, after taking down existing joint, complete all as specified and directed. |
| 29 | Materials and Labour for,run lead joint for cast iron spigot and socket pipes and fittings for water mains ,80 mm bore, including burning out lead joints in position and including removing old lead from site, complete all as specified and directed. NOTE:- Earthwork will be measured and paid seperatly. |
| 30 | Materials and Labour for,run lead joint for cast iron spigot and socket pipes and fittings for water mains ,100 mm bore, including burning out lead joints in position and including removing old lead from site,complete all as specified and directed. NOTE:- Earthwork will be measured and paid seperatly. |
| 31 | Materials and Labour for,run lead joint for cast iron spigot and socket pipes and fittings for water mains ,150 mm bore, including burning out lead joints in position and including removing old lead from site, complete all as specified and directed. NOTE:- Earthwork will be measured and paid seperatly. |
| 32 | Supply and fixingin repair ofPVC ball valve for 15 mm dia pipe all completecomplete all as specified and directed. |
| 33 | Supply and fixingin repair ofPVC ball valve for 20 mm dia pipe all completecomplete all as specified and directed. |
| 34 | Supply and fixingin repair ofPVC ball valve for 25mm dia pipe all completecomplete all as specified and directed. |
| 35 | Supply and fixingin repair ofstraight plain brass ferrules (or connecting screws) screwed both ends for 15 mm bore pipes and fixed,complete all as specified and directed. |
| 36 | Supply and fixingin repair of PP-Rpipe fittingfor 110/ 90 mm outer dia PP-R pipesuch as Bends, Elbows, Tees, Short Pieces, Connectorsetc , cupler, unionor other accessories all as specified and directed . |
| 37 | Supply and fixingin repair of PP-Rpipe fittingfo 63 mm outer dia PP-R pipesuch as Bends, Elbows, Tees, Short Pieces, Connectorsetc , cupler, unionor other accessories all as specified and directed . |
| 38 | Supply and fixingin repair of PP-Rpipe fittingfo 50mm outer dia PP-R pipesuch as Bends, Elbows, Tees, Short Pieces, Connectorsetc , cupler, unionor other accessories all as specified and directed . |
| 39 | Supply and fixingin repair of PP-Rpipe fittingfo 32 mm outer dia PP-R pipesuch as Bends, Elbows, Tees, Short Pieces, Connectorsetc , cupler, unionor other accessories all as specified and directed . |
| 40 | Material and labourfor cleaning ofPVC tank of capacityexceeding 1000 ltr with fibre brush to remove all dirts and removing sediments and through cleaning of rotational moulded polythene water storage tank and then with dilute bleaching powder solution(not less than 1.2 Kg per tank) and and finally cleaning with fresh water complete all as directed. |
| 41 | Material and labourfor cleaning ofPVC tank of capacity exceeding 750 ltrand not exceeding 1000 ltr with fibre brush to remove all dirts and removing sediments and through cleaning of rotational moulded polythene water storage tank and then with dilute bleaching powder solution(not less than 1.2 Kg per tank) and and finally cleaning with fresh water complete all as directed. |
| 42 | Material and labourfor cleaning ofPVC tank of capacity exceeding 250 ltrand not exceeding 500 ltr with fibre brush to remove all dirts and removing sediments and through cleaning of rotational moulded polythene water storage tank and then with dilute bleaching powder solution(not less than 0.75Kg per tank) and and finally cleaning with fresh water complete all as directed. |
| 43 | Material and labour for cleaning /de-sludging / de-silting of 96 00 gallons capacity overhead PS reservoir12.00m stagingby draining out water / sludge from tank, removing all scales, dirt, algae and other growths from floor, roof, inside of tanks and from mouths of circulating pipes by rubbing with wire brushes or mechanically from site to a distance n.exc 50 Mtr,washing the tank with bleaching powder (not less than 10Kg per reservoir) for making surface bacteria free and finally cleaning with fresh water , normalizing the water supply by opening the inlet / outlet valves after allowing sufficient drying time complete all as directed. |
| 44 | Material and labour for cleaning /de-sludging / de-silting of 1,00, 000 gallons capacity Steel sedimentation tankby draining out water / sludge from tank, removing all scales, dirt, algae and other growths from floor, roof, inside of tanks and from mouths of circulating pipes by rubbing with wire brushes or mechanically from site to a distance n.exc 50 Mtr,washing the tank with bleaching powder (not less than 30 Kg per reservoir) for making surface bacteria free and finally cleaning with fresh water , normalizing the water supply by opening the inlet / outlet valves after allowing sufficient drying time complete all as directed. |
| 45 | Material and labour for cleaning /de-sludging / de-silting of 1,00, 000 gallons capacity RCC Retention tankby draining out water / sludge from tank, removing all scales, dirt, algae and other growths from floor, roof, inside of tanks and from mouths of circulating pipes by rubbing with wire brushes or mechanically from site to a distance n.exc 50 Mtr,washing the tank with bleaching powder (not less than 30 Kg per reservoir) for making surface bacteria free and finally cleaning with fresh water , normalizing the water supply by opening the inlet / outlet valves after allowing sufficient drying time complete all as directed. |
| 46 | Material and labour for cleaning /de-sludging / de-silting of 80,000 gallons capacity RCC overhead reservoir12.00m stagingby draining out water / sludge from tank, removing all scales, dirt, algae and other growths from floor, roof, inside of tanks and from mouths of circulating pipes by rubbing with wire brushes or mechanically from site to a distance n.exc 50 Mtr,washing the tank with bleaching powder (not less than 30 Kg per reservoir) for making surface bacteria free and finally cleaning with fresh water , normalizing the water supply by opening the inlet / outlet valves after allowing sufficient drying time complete all as directed.Note for item No ____to _____:-1. After cleaning, the date of cleaning is required to be written, with size of letters / numbers as directed by the Engineer-in-Charge, in white colour paint with a black paint background.2.Tanks mentioned under Item No. _____shall be cleaned twice during the contract period, once after commencement of work and once before completion of work. Other tanks shall be cleaned once during the contract period unless otherwise directed by Engineer-in-Charge.date of cleaning of tank shall also be recorded in MB against respective item.3.Contractor shall submit purchase voucher for \"Bleaching Powder\" which shall be recorded in MB as \"Not To Be Abstracted\". |
| 47 | Material and labourfor two coats of synthetic enamel paint over a coat of red oxide primer including preparation of old rusted surface of steel exc 10 cm width/grith, at any height of tank and water supply vertical pipes of pumping and distribtion lines as per differentcolour code and marking of arrow for flowing of water with approved color shade paint complete all as specified and directed. |
| 48 | Material and labour for completeremoval of existing treatment of external wallsurface of 80,000 Gallons 12 m Staging RCC Overhead Tank by manually /mechanical appliance and preparation ofold surfaces applying two coats of acrylic exteriorweather resistant paint(weather proof paint @ 1.67 ltr/10 sqmper two coats ) of required colour shade and as per manufacturer’s specification over a coat of acrylic exterior primer((@ 2.20 kg/10 sqm) complete all as specified and directed.Note :-The colour shade of tank shall be green(army) and white combination as directed by GE. The quoted rate shall irrespective height. |
| 49 | Material and labour for completeremoval of existing treatment of internal wallsurface of RCC sedimentation tank by manually and appliance and preparation ofold surfaces applying Non toxic two coats of two-component polymer modifi ed cementitious coating (3.6 Kg/ Sqmper two coats )complete all as specified and directed.Make:- Nitocote CM210 of FOSROC or equivalents approved chemical given in approved make list of PS |
| 50 | Supply and fixing in repair of sluice valve cast iron body class PN-1.5 with flanged ends drilled suitable for bore of pipe 150mm, conforming to IS: 14846 with and including brass spindle, MS bolts, nuts, washers and a pair of rubber gasket ISI markincluding taking dwon old one complete all as specified. |
| 51 | Supply and fixing in repair of sluice valve cast iron body class PN-1.5 with flanged ends drilled suitable for bore of pipe 100mm, conforming to IS: 14846 with and including brass spindle, MS bolts, nuts, washers and a pair of rubber gasket ISI markincluding taking dwon old one complete all as specified. |
| 52 | Supply and laying of 3- layer PP-R (Polypropylene random copolymer)concealed pipes 32 mm outer dia ,SDR 7.4 (PN-16) pipes UVstabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and directed. |
| 53 | Supply and laying of 3- layer PP-R (Polypropylene random copolymer)concealed pipes 25 mm outer dia ,SDR 7.4 (PN-16) pipes UVstabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and directed. |
| 54 | Materials and Labour for, plain rolled mild steel plates of thickness 3.00 mmas in top cover of PS tank, bend to shape required including necessary cutting, drilling hole etc., fixing withnut , bolts , washers and jointing materials such as lead wood, gasket, black non toxic putty, etc., and including applying two coat of black bituminous lead free paint (Drinking Water Grade) over a coat of red oxide primer internally and two coats of aluminium paint over a coat of red oxide zinc chrome primer externally, including taking down existing unserviceable top cover, complete all as specified and directed. |
| 55 | Material & labour of Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410W (Gde- E- 250) quality- A and fabrication of MS Trolley including cutting existing damage plate at existing member of WTP and welding as per site requirement complete all as specified and directed. |
| 56 | Materials and Labour for, repair / renewal of RCC foundation of Oxidation chamber 10000 GPH , including removal of oxidation tower from site and making new RCC footing for foundation of Oxidation Legs and refixing of old Oxidation chamber at site making all suitable connection with existing GI pipes and renewal of old gaskets and bolts, nuts and painting of oxidation chamber and making repairs of any leakage in pipe complete all as specified and directed. |
| 57 | Material and labour for construction of brick masonry chamber with subclass `B\" brick in CM (1:6) with PCC (1:4:8) type D2 for foundation of internal dimension of 100mx100cmx100cm including 15mm thick plastering in CM (1:4) inside the chamber and on the external portion exposed above ground level, including 3mm thick MS cover welded around with MS flat iron of size 40x6mm including MS angle iron frame of size 40x40x6mm with locking arrangement including painting with two coats of synthetic enamel paint over a coat of red oxide primer including necessary earthwork in soft/loose soil well ramming of soil around the constructed chamberincluding demolotion old one complete all as specifiedandas directed. |
| 58 | Material and labour for construction of brick masonry chamber with subclass `B\" brick in CM (1:6) with PCC (1:4:8) type D2 for foundation of internal dimension of 60mx60cmx100cm including 15mm thick plastering in CM (1:4) inside the chamber and on the external portion exposed above ground level, including 3mm thick MS cover welded around with MS flat iron of size 40x6mm including MS angle iron frame of size 40x40x6mm with locking arrangement including painting with two coats of synthetic enamel paint over a coat of red oxide primer including necessary earthwork in soft/loose soil well ramming of soil around the constructed chamberincluding demolotion old one complete all as specifiedandas directed. |
| 59 | Dismantling the old unserviceable items from the existing feed type pressure filter plant of 10000 GPH capacity incl opening the man hole cover taking out all filter media i.e. sand, gravels, pebbles, stainer, MNO2, Resin, valves, pipe fittings with complete connection of pipes & valves and repairing the same including re-filling of exsiting filter media/chemicals and new filling of filter media/chemicals after washing with suitable type chemicals as rquired and testing complete all as specified and as directed.Notes:-(a)Quoted rate is deemed to be inclusive of :-(i)keeping leak proof of whole plants, all Sluice/ diaphragm/ flanged valves, replacement of rubber hose, clamps, etc.(ii) Filling of all filter media to plants like gravels, pebbles, sand, catalyst MNO2, resin, strainer etc. (iii)Disconnection or interconnection pipes of any sizes, valves, gauges, and all accessories etc., including reassembling the whole plant by welding., jointing etc. (iv)Testing of water for Iron, PH value, Hardness, Residual chlorine etc.(b)New items like pressure guage, pipes/flanges of any type & any size, valves of any type, diaphragm, painting, water testing, filter media, nut, bolt , washers shall be measured and paid separately under relevant items of this schedule.(c) Contractor is advised to visit the site prior to quoting their offer. No claim shall be admissible at a later stage. |
| 60 | Supply only filtration media sand ,effective size0.35 mm to 0.50 mm, hard and resistant, quartz or quartzite, free from clay, fine particles, soft grains and dirt of every description, conforming to IS 8419, Part-I, inside existing rapid gravity filter & pressure filter |
| 61 | Supply only 3 to 6 mm gravels suitable for rapid gravity filter & pressure filter |
| 62 | Supply only 6 to 12 mm gravels suitable for rapid gravity filter & pressure filter |
| 63 | Supply only 12 to 20 mm gravels suitable for rapid gravity filter & pressure filter |
| 64 | Supply only 20 to 40 mm gravels suitable for rapid gravity filter & pressure filterNote for item No 60 to 65:-1. After cleaning, the date of cleaning is required to be written, with size of letters / numbers as directed by the Engineer-in-Charge, in white colour paint with a black paint background.2. Date of cleaning ofpressure filter plant shall also be recorded in MB against respective item.3.Contractor shall submit purchase voucher for \"filter media\" which shall be recorded in MB as \"Not To Be Abstracted\". |
| 65 | Supply only Manganese dioxide(MnO2) of approximate sizes 20 mm to 25 mm containing at least 65% of manganese, suitable for use in filtration plant complete all as specified and as directed by Engineer-in-Charge. Note:- Samples of raw material (MnO2) should be got tested in Govt approved laboratory before using in the oxidation chamber for determining the MNO2 purity, which shall not be less than 65% ((MNO2 contents minimum 65% purity), testing charge for the same is deemed to be included in the cost quoted by the contractor. |
| 66 | Materials and Labour for one coat of food grade black bituminious paint suitable for portable drinking water after necessary preparation of internal surfaces of plants consisting of one pressure filter of capacity 10000 LPH including necessary connected pipe lines and valves complete all as specified and directed by Engineer-in-Charge. |
| 67 | Dismantling, repairing/replacement, re-fixing and commissioning, testing ofthe Air scour Rotary twin-lobe blower/compressor 12 KG/Sqcm from the foundation andservicing/ replacement of defective spears parts atworkshop as approved by GE/Engineer-in-charge and includingcleaning the air filter, lubricating the mechanical parts like lobes, gears, bearings ,replacing damage spare parts for Compressor kit, fly wheel, Air Pressure Gauge, Gland Packing Seal, Coupling etc(if required like) and also including filling thecompressor lubricantoil ( Servo system 320 of IOC and ENCLO-320 of HPCL)-03 ltrs and replacement of a air cleaner filter of air blower and any other part required for fullyfunction of plantand refixingat the same place including connecting all electrical connections and V- belt and testing complete all as specified and directed by GE.Note:- The quoted rate shall be deem to be included allspare parts, lubricant oil, servicing charge, transportation charge and. Contractor is advised to visit the site prior to submission of bid. No claim shall be admissible at a later stage. |
| 68 | Materials and Labour for galvanized steel tubing, medium grade, 15 mm bore with all fittings, fixing to wall with MS claim and including taking up old GI pipe complete all as specified and as directed.Note - All fitting & fixture such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector, holding clampshall be provide as per site requiredment and same shall deem to be included in quoted rate. |
| 69 | Supply and fixingin repairof any leakage exsiting GIpipeline of 20-40 mm diawith replacement of new GI pipe fittings at any location orfoul condition(if any)including necessary T&P all as specified and directed.Note:- Earth/ Excavation works for repairing damage pipeline will be measured and paid separately. |
| 70 | Supply and fixingin repairof any leakage exsiting GIpipeline of 50-80 mm diawith replacement of new GI pipe fittings at any location orfoul condition(if any)including necessary T&P all as specified and directed.Note:- Earth/ Excavation works for repairing damage pipeline will be measured and paid separately. |
| 71 | Supply and fixingin repairof any leakage exsiting CI/DIpipeline of 100 mm dia to 200 mm dia with replacement of new jointing materials such as lead wool/ leather gasket / rubber gasket ring /push on joint / socket / union or any reqd pipe fittings for CI /DI /MS pipe line with reqd nuts/ bolts/ washer and necessary welding works (as reqd). at any location orfoul condition(if any)including necessary T&P all as specified and directed.Note:- Earth/ Excavation works for repairing damage pipeline will be measured and paid separately. |
| 72 | PUMP REPAIR PORTION (Sl No __ to ____) |
| 73 | Material and labour for overhauling/comprehensive maintenance of centrifugal / monoblock / submersible pump set following capacity and includingdusting/cleaning by smooth brushingand lubricating of movable mechanism suitably with oil/grease and replacement of unserviceable/burnt out/worn out spare parts with new one as per existing make, duly commissioned in the same location necessary inspection, reassembling ,testing , re-commissioning, etc complete for smooth functioning of the pumps to ensure desired result complete all as specifiedand as directedNote:- (i)Labour component required for the replacements of unserviceable parts shall be deemed to be included in the unit rate quoted against this item (ii) Following parts mentation in BOQhere-in -after shall be measured and paid separatelyand other parts if required for functioning of Pump set shall be provided by the contractor and the cost thereof shall be deemed to be includedin theunit rate quoted against above items.(iii) T&P and minor parts will be arranged by the contractor and the cost thereof shall be deemed to be includedin theunit rate quoted against this item .(iv) The cost oftransportation/service engineer(if required) and other necessary equipment shall be arranged/brought by the contractor in this effect , hence the bidder/tenderer is advised to visit the site and assess the quantum of the work to be carried out in the contract. The cost of the same is deemed included quoted rates and no extra cost shall be paid to the contractor in this effect. |
| 74 | CentrifugalPump set of 25 / 20 HP |
| 75 | Centrifugal Pump set of 15/12.5 HP |
| 76 | Monoblock Pump set of 15 HP |
| 77 | Submersible Pump set of 15 /12.5 HP |
| 78 | Submersible Pump set of 10/ 7.5 HP |
| 79 | Monoblock Pump set of 2 /1 / 0.5 HP |
| 80 | Supply only Spare Parts for the following capacity of pumping sets:- |
| 81 | Impeller for Centrifugal Pump set of 25 / 20 HP |
| 82 | Impeller for Centrifugal Pump set of 15/12.5 HP |
| 83 | Impeller forMonoblock Pump set of 15 HP |
| 84 | Impeller forMonoblock Pump set of 10/7.5 HP |
| 85 | Impeller for Submersible Pump set of 15 / 12.5HP |
| 86 | Impeller for Submersible Pump set of 10 / 7.5HP |
| 87 | Pump Shaft for Centrifugal Pump set of 25 / 20 HP |
| 88 | Pump Shaft for Centrifugal Pump set of 15/12.5 HP |
| 89 | Pump Shaft for Monoblock Pump setof 15 HP |
| 90 | Pump Shaft for Monoblock Pump set of 10/7.5 HP |
| 91 | Bearing for Centrifugal Pump set of 25 / 20 HP |
| 92 | Bearing for Centrifugal Pump set of 15/12.5 HP |
| 93 | Bearing for Monoblock Pump set of 15/12.5 HP |
| 94 | Bushing for Submersible Pump set of 15/12.5 HP |
| 95 | Bushingfor Submersible Pump set of 10/7.5 HP |
| 96 | Pump Shaft for Submersible Pump set of 15/12.5 HP |
| 97 | Pump Shaft for Submersible Pump set of 10/7.5 HP |
| 98 | Thrust Bearing for Submersible Pump set of 15/12.5 HP |
| 99 | Material and labour for overhauling/comprehensive maintenance of Induction Motor of 3 Phase, 415 Volts following capacity and includingdusting/cleaning by smooth brushingand lubricating of movable mechanism suitably with oil/grease and replacement of unserviceable/burnt out/worn out spare parts with new one as per existing make, windings of stator and rewinding with same size of super enamelled copper wire with necessary insulating material, varnishing backing, replacing DE/NDE bearings and reassembling the motorduly commissioned in the same location with necessary inspection, reassembling ,testing , re-commissioning, etc complete for smooth functioning of the motors to ensure desired result complete all as specifiedand as directed.Note:- (i)Labour component required for the replacements of unserviceable parts, rewinding motors shall be deemed to be included in the unit rate quoted against this item (ii) All replacement parts (Excepts Bearing & Bushing) required for functioning of motor set shall be provided by the contractor and the cost thereof shall be deemed to be includedin theunit rate quoted against above items.(iii) T&P and minor parts will be arranged by the contractor and the cost thereof shall be deemed to be includedin theunit rate quoted against this item .(iv) The cost oftransportation/service engineer(if required) and other necessary equipment shall be arranged/brought by the contractor in this effect , hence the bidder/tenderer is advised to visit the site and assess the quantum of the work to be carried out in the contract. The cost of the same is deemed included quoted rates and no extra cost shall be paid to the contractor in this effect. |
| 100 | Electric motor of 25/20 HP for centrifugal P/Set |
| 101 | Electric motor of 15/12.5 HP for centrifugal P/Set |
| 102 | Electric motor of 15 HP for monoblock P/Set |
| 103 | Electric motor of 15/12.5 HP for Submersible P/Set |
| 104 | Electric motor of 2/1/0.5 HP for submersible P/Set |
| 105 | Material and labour for spray painting of two coat of synthetic enamel paint (smoke grey/blue shade)after cleaning all dirts from old surface for pump set of different capacity and other equipments complete as required for following capacity of pump setincluding writing of MES No complete all as specifiedand as directed. |
| 106 | Pump set of 25 HP / 20 HP capacity |
| 107 | Pump set of 15 HP / 12.50 HP capacity |
| 108 | Pump set of 1.50 HP / 1.00 HP capacity |
| 109 | Supply and fixing as in repair of electronic timer ST-100, 415 V, 50 Hz. complete all as specified and directeddirected by Enng-in-charge.Make : L & T Cat No ST80329OOOO or equivalent model of make list as given in PS as approved by GE. |
| 110 | Supply and fixing as in repair ofpower contactor 3 pole 25 amps complete all as specified and directeddirected by Enng-in-charge.Make L&TCat No. SS91851 or equivalent as approved by GE from list of approved makes. |
| 111 | Supply and fixing as in repair of auxiliary contact block for MNX contactor (2 NO + 2 NC ), 25 ampscomplete all as specified and directeddirected by Enng-in-charge. Make L&TCat No. CS94114 or equivalent as approved by GE from list of approved makes. |
| 112 | Supply and fixing as in repair of Thermal Overload Relays,type ML 1 (Directly Operated),relay range 10-16 Amps, complete all as specified and directeddirected by Enng-in-charge.Make:- Cat No.SS91858OOBO ofL&T or equivalent as approved by GE from list of approved makes. |
| 113 | Supply and fixing as in repair of , panel mounted protection device for,single phasing, reverse phasing, unbalanced supply with auto reset, 1 NO output contact with pre-wired terminals,suitable for any HP/kW rating pump motor.complete all as specified and directed.Make :L&T Cat No. SS94142OOBO or equivalent as approved by GE from list of approved makes. |
| 114 | Supply and fixing as in repair ofFully Automatic Star Delta Starter 12.5 / 15 HP, 9 - 14 Amp , 440 Volt , 50 Hz for Submersible pump all as specified and directed by Engr-in-Charge. Make L & T Cat No. SS94362 or equivalent as approved by GE from list of approved makes. |
| 115 | Material & labour for Plain Cement Conerete1 : 3 : 6 type C2 using 40 mm graded stone agregate as in foundation/platform of pump set/pump panel & other works at different pump house complete all as specified and as directed by the Engr-in-charge. |
| 116 | Demolition of existing unreinforced PCC complete all as specified and as directed by the Engr-in-charge. |
| 117 | Supply and laying or fixing or passing through pipe PVC insulated Submersible cable for working voltages of 1100 V, PVC sheathed, armoured, 3 core, nominal cross sectional area of main conductor 6 sqmm, stranded aluminium conductor, ISI marked as per IS 1554(Part-I): 1988including taking down old old cable complete all as specified and directed. |
| 118 | Material & Labour of sand cushioning to the full width of trenches for protection of cables including punning down complete all as specified and directed.Note :- Thickness of sand cushioning shall be measure after punning down. |
| 119 | Supply and laying for brick protection of UG cable with sub class \"B\"complete all as specified and directed. |
| 120 | Lifting of submersible pump set of capacity 5 to 15 HP from exisiting borewell of depth 150mtr along with column pipe 80/ 100 mm bore total length 30 RM after disconnecting the pipe from the circuit and reassemble after overhauling and repair, reconnection of motor and lowering with new/ old column pipe including replacement of new joint fitting material in the same borewell complete all as specified and directed.Note : (a) The cost of overhauling, repair, new column pipe and submersible cable shall be measure and paid under relevant item as above.(b) Equipment like tripod and chain pulley block etc, are required for this job and the same shall be arranged by the contractor and the rates quoted is deemed to included for the same. |
| 121 | Supply only 80mm GI column pipe flange type suitable for subersible pump, ISI marked,both ends flanged including gasket, nuts and Boltscomplete all as specified and directed.Note : Lifting and lowering pipe into Borewell shall be deemed included in the quoted rate of item No 89 above. |
| 122 | Supply, fixing & repair of the flexibel hose pipe with new reinforced PVC flexible hose pipe for suction of size 50mm dia with 2 Nos of suitable clamps and 1 No of hose pipe adopte etc complete all as specified and directed. |
| 123 | Note: Schedule of credit (SCHEDULE OF CREDIT)amount of Rs ?___________mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ. |
