|
| 1 | Taking down Shutters of any description exc 1 sq. mand n exc 2 sqm eachcomplete all as specified and as directed. |
| 2 | Taking down Chowkat or frames with shutters(without taking off shutters from the frames)exc 1.5 but n.exc 4.00 sqm eachcomplete all as specified and as directed. |
| 3 | Taking down and removing Chowkats or frames not exc. 1.5 sq.m with shutter (without taking off shutters from the frames) complete all as specified and as directed. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premisecomplete all as specified and as directed. |
| 5 | Dismantling Stone Slabs and/or Tiles of any description or thickness in Floors, Aprons, etc. laid, bedded and pointed in Cement Mortar and removing debris, etc. to Outside MD/AF Land,complete all as specified and as directed. |
| 6 | Demolition of cement concrete (unreinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level)complete all as specified and as directed. |
| 7 | Taking down cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc.complete all as specified and as directed. |
| 8 | Dismantling Structural Steel or Mild Steel Work of any description including Framed Truss, etc., complete all as specified and as directed. |
| 9 | Dismantling damaged/unserviceable Galvalume, AC andFiber Sheeting of any gauge and thickness, complete all as specified and as directed. |
| 10 | S&F Aluminium anodizedpowder coated(minimum thickenss of powder coating 50 micron) three track sliding Window, Shutters (size 45x15mm) i.e two shutter with 4.8 mm thick tinted glass and one with stainless steel wire cloth of 0.36 mm dia and avg width of aperture 1.40 mm and sliding section conmfirming Cat No. 20814(from Jindal) and frame size 101.40x44.50 x1.90 mm etc including all necessary locking arrangement complete all as specified and directed. Aluminium Grill to be provided , etc. complete including necessary Jointing Cleats, Glazing Clips, Rubber Packing, Aluminium Snap Beading, NOTE : (a)Cost of Black/Tinted Sheet Glass, Stainless Steel Wire Cloth, Jointing & Packing Materials, anodized Aluminium Fittings, etc. shall deem to be include in the Quoted Unit Rate.(b)For the purpose of Measurement & Payment all Shutters with Frame shall be considered as One Unit and only front portion shall be measured for payment. |
| 11 | S&F 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate, Filling the frame with cement concrete Type B-0 1:2:4 ( (12.5 mm granded stone aggregates) etc complete all as specified and as directed. |
| 12 | S&F 1.25 mm thick pressed steel frame of size 105 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate, Filling the frame with cement concrete Type B-0 1:2:4 ( (12.5 mm granded stone aggregates)etccomplete all as specified and as directed. |
| 13 | S&F in repairs Factory made solid panel PVC door shutter 30mm thick(style) consisting of frame made out of MS tubes for top and bottom rails.MS frame shall becovered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottim rail.Penelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling & fixing in the frame at site as per specification & drawingcomplete all as specified and as directed. |
| 14 | S & F solid PVC doorframe of size 50mm x 95mm made out of5 mm single side prelam PVC sheet used instead of plain colour PVC sheet reinforced with Ms Squre Tube in opening etc complete all as specified and as directed. |
| 15 | S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed. |
| 16 | S&F 35 mm thick 2nd class Hard wood Glazed and skelton shutters, open rebated and prepared to receive glass, guaze etc, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securiing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20(a) and fitted to chowkats complete all as specified and as directed. |
| 17 | S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side complete all as specified and as directed. |
| 18 | S&F Stainless Steel Butt Hinge 75mm long (weight not less than 60 Gram) and fixed, complete all as specified and as directed. |
| 19 | S&F Cold Rolled Mild Steel Butt Hinge 100mm long medium weight and fixed, complete all as specified and as directed. |
| 20 | S & F aluminium anodised, barrel tower bolts of extruded section 125mm long and fixed complete all as specified and as directed. |
| 21 | S & F aluminium anodised, barrel tower bolts of extruded section 200mm long and fixed complete all as specified and as directed. |
| 22 | S&F 250mm Aluminium alloy, anodised, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of exctruded sections or cast aluminium alloy and fixed complete all as specified and as directed. |
| 23 | S&F Aluminium Handle 100mm long (weight not less than 90 Gram), Cast type, anodised, complete all as specified and as directed. |
| 24 | S&F Aluminium Handle 150mm long (weight not less than 120 Gram), Cast type, anodised, complete all as specified and as directed. |
| 25 | S & F for Galvanised mildsteelwire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed. |
| 26 | S & F for mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate completeall as specified and as directed. |
| 27 | M&L for Glazed coloured ceramic tiles in vertical surfaces 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surface as backing coat coat of dado/skirting etc complete all as specified and as directed . |
| 28 | M&L for Non skid coloured ceramic tiles 600x600area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick Screed bed or bedding layer of mortar for lying floor finished in Cement Mortar 1:4 complete all as specified and as directed . |
| 29 | M&L for Non skid coloured ceramic tiles 300x300area of each tile not exceeding 0.11 Sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick Screed bed or bedding layer of mortar for lying floor finished in Cement Mortar 1:4 complete all as specified and as directed. |
| 30 | M&L for 25mm thick Cement concrete 1:2:4 type B-O(using 12.5mm graded aggregate) as in flooring, finished surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 31 | M&L for Machine cut Granite Stone Slab (Black in colour) 16-20mm thick, fixed on Kitchen Platform, Floor or on Shelves, laid over and including Cement Screed 15mm thick in Cement Mortar 1:4, cutting and Granite Polishing using White Cement in Joints including rounding Edge of Stone Slab on One Edge, complete all as specified and as directed. |
| 32 | Taking up or down steel tubing 15 mm bore, and connections, including removal to store or under credit schedule complete all as specified and as directed. |
| 33 | Taking up or down steel tubing 20 mm bore, and connections, including removal to store or under credit schedule complete all as specified and as directed. |
| 34 | S&F 15 mm bore tubes medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed. |
| 35 | S&F 20 mm bore tubes medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed. |
| 36 | S & F in repairs 15mm bore Bib taps, fancy type chromium plated cast copper alloy with crutch or butterly handle, screwed down, screwed with cupfor iron pipe or for brass ferrule and fixed complete all as specified and as directed. |
| 37 | S & F in repairs 15mm bore Stop Valve/ angle valve fancy type chromium plated , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends with cup for iron pipe or for unions and fixed complete all as specified and as directed. |
| 38 | S&F in repair Pillar Tap 15mm bore (dia), Cast Copper alloy with Capstan Heads, Chromium Plated, Fancy type screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed. |
| 39 | S & F in repair 15mm bore brass CP wall mixer with provision for overhead shower with 115mm long bend pipe on upper side, connecting & wall flange fancy type,cast copper alloy,chromium complete all as specified and as directed. |
| 40 | S & F in repair single towel rail 450mm long fancy type chromium plated fixed with PVC plug and steel screw complete all as specified and as directed. |
| 41 | M & L in repair for hand shower (health faucet) with 8mm dia 1.20 mm lonf flexible tube and wall hook complete all as specified and as directed. |
| 42 | S & F in repairfor PVC conection 15 mm size with PTMT nuts of length 450 mm long complete all as specified and as directed. |
| 43 | S & F in repair Swivel shower of PTMT any colour forfixing with 15mm pipe. (Minimum weight 40gms complete all as specified and as directed. |
| 44 | S&F Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) size 350x475x390 with Trap and Fixing Bolts and Making Good to Floor/ distrubed surfaces and fixed-in-repairs, complete all as specified and as directed. MAKE : HINDUSTAN SANITARYWARE 21027/ JAQUAR CNS-WHT553SN/ PARRYWARE C-0252(S) or equivalent out of makes specified in list of makes. |
| 45 | S&F Plastic Water Closet SeatCover for Water Closet Pan (Pedestal Pattern), White, Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device and fixed-in-repairs, complete all as specified and as directed.MAKE : JAQUAR CNS-WHT-111N or equivalent out of makes specified in list of makes. |
| 46 | S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back type) with 32mm dia Brass Chromium Plated Waste Fitting, a Pair of Cast Iron Brackets duly Painted/Erecting Stand including Cutting and Pinning in Ends, Making Good disturbed surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed. MAKE: CERA 1003 (COUNSEL)/ PARRYWARE C-0406 or equivalent out of makes specified in list of makes. |
| 47 | S&F Vitreous China White Squatting Pan of size 580x440mm, \"Orissa\" Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) incluiding provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces and fixed-in-repairs, complete all as specified and as directed. MAKE : HINDUSTAN SANITARYWARE 20042 (Stra White) or equivalent out of makes specified in list of makes. |
| 48 | S&F PVC Flushing Cistern 10 Litre capacity twin flush type White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float and Handle, a pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed. MAKE : CERA (CAMELIA) Cat No. 2603/ PARRYWAREor equivalent out of makes specified in list of makes. |
| 49 | S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratorywith plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mmcomplete all as specified and as directed. |
| 50 | M&L for Rough cast plaster on brick walls consisting under coat of cement and sand mortar 1:3 not less than 10mmm thick and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel mixed of size 6mm with coarse sand and cement in the ratio 1:1:1 shall be applied and finish even complete all as specified and as directed. |
| 51 | M&L for 15mm thick Rendering on fair faces of brick work or concrete sureces in Cement Moratar 1:6 finished surface even and smooth without using extra cement complete all as specified and as directed. (Note the area includs in this up to 4th stories building ) |
| 52 | M&L Rendering (External) 15mm thick in Cement Mortar 1:4 on Brick Walls/Concrete Surfaces upto double storey, mixing with WPC as per Manufactures instruction, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed. NOTE : WPC shall be Measured and Paid for as ‘Supply only’ separately under appropriate Item. |
| 53 | Supply only Integral Water Proofing Compound, conforming to IS and/or as approved, complete all as specified. |
| 54 | M&L for 10mm thick Rendering on ceiling surface fair faces of brick work or concrete sureces in Cement Moratar 1:3 finished surface even and smooth without using extra cement complete all as specified and as directed.(Note the area includs in this up to 4th stories building). |
| 55 | S&F Stainless Steel Curtain Rod 25mm dia/bore (as approved) includingfixing stainless steel Bracket(shaped as approved) not less than 80mm longto wall with Screws/ securedwith stainless steel side doom(as approved) fitted/tightened on Curtain Rod at both ends with screw including taking down old curtain rod of any description, complete all as specified and as directed. |
| 56 | S&F Looking Mirror 5.0mm thick of size 450x600mm, fixed with Chromium Plated Brass Spacers 25mm to 30mm in size (One Each Corner) including rounding the edges of the Mirror and Fixed-in-repairs, complete all as specified and as directed. |
| 57 | Hacking out old broken glass(any thickness, size, quality or description) from wooden frames or metal frame including punching or drilling out old glazing pin/ spring clip or glazed with oil putty or fixed with window beads complete all as specified and as directed. |
| 58 | S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty or wooden beading to wooden frame or steel frame in square n exc 0.5sqm each pane complete all as specified and as directed. |
| 59 | M & L for a coat of alkali resistant over already prepared surface of wall complete all as specified and as directed. |
| 60 | M&L for Providing plaster of paris putty of 1mm thickness on plastered surface to prepare the surface smooth and finishes complete all as specified and as directed. |
| 61 | M&L for preparing newly Rough Cast plastered surfaces of Walls and applying Two Coats of Weather Coat Exterior Paint (in Camuflage/Plain pattern as ordered) with approved Tint over a coat of Primer (as per Manufacturer\"s instructions), complete all as specified and as directed. |
| 62 | M&L for preparing old Distempered surfaces of Walls by brooming down or steel wire brushing and scraping down andfilling the existing Nails/ Screw Holes, etc. and applying Two Coats of Distemper Oil Emulsion (as approved), complete all as specified and as directed. |
| 63 | M&L for preparation of old plastered or unplastered surface of ceiling including cornices etc. by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and removal of vegetation and applying two coat of white wash on old surface of ceiling complete all as specified and as directed. |
| 64 | M & L for newplaster surface applying three coat white wash ceiling surface with roller brush complete all as specified and as directed. |
| 65 | M&L for preparing new Plastered surfaces of Walls by applying Wall Care Putty 1 to 1.5 mm thickncluding Rubbing down with Sand Paper to obtain a Smooth Finish Surface and applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Primer, complete all as specified and as directed. |
| 66 | M&L for preparing newly Plastered surfaces of Walls by applying Wall Putty 1 to 1.5 mm thick , cutting/rubbing to obtained a Smooth Surface and applying Two Coats of Weather Coat Exterior Paint with approved Tint over a coat of Primer (as per Manufacturer\"s instructions), complete all as specified and as directed. |
| 67 | M&L for preparing old Decorated/Treated Plastered surfaces of Wallsby brooming down or steel wire brushing and scraping downand applying Two Coats of Weather Coat Exterior Paint (in Camuflage/Plain pattern as ordered) with approved Tint(as per Manufacturer\"s instructions), complete all as specified and as directed. |
| 68 | M&L for preparing new wooden surfaces of any description, not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over pink primer complete all as specified and as directed. |
| 69 | M&L for Preparing old painted surfaces of wood of any description, not otherwise described, over 10cm width or girth and one coat of synthetic enamel paint complete all as specified and as directed. |
| 70 | M&L for preparing old painted steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enemal paint complete all as specified and as directed. |
| 71 | S&F 75mm bore PVC(SWR) pipes single socketed in any lengthpressure rating 4Kg/Sq cmmedium Grade with rubber ring joints fixed to walls with MS Clamp dash true nut and bolt complete all as specified and as directed. |
| 72 | S & F 75mm dia PVC (SWR)bends/shoe with rubber rings joints fixed as required complete all as specifiedand as directed |
| 73 | S&F 110mm bore PVC(SWR) pipes single socketed in any lengthpressure rating 4Kg/Sq cmmedium Grade with rubber ring joints fixed to walls with MS Clamp dash true nut and bolt complete all as specified and as directed. |
| 74 | S & F 110mm dia PVC (SWR)bends/shoe with rubber rings joints fixed as required complete all as specifiedand as directed. |
| 75 | M&L for rendering 15 mm thick in CM (1:3) mixed with water proofing compound @ 3% by weight of cement finishedeven and smooth without using extra cement in sunken portion of toilet etc complete all as specified and as directed. Note: WPC will be measured and paid separtely . |
| 76 | M&L for two coat of painting with Dr Fixit fast Flex (or equivalent) water proofing liquid including preparation of new plastered surfaces complete all as specified and as directed. |
| 77 | M&L for cement concrete 1:5:10 type E-2 using 20mm granded crushed Brick aggregates as in sunken portion of WC etc complete all as specified and as directed |
| 78 | Taking down PVC/cast iron pipes any bore including fittings of anydia with cement or lead joint fixed to walls or laid in trenches complete for refixing or replacement complete all as specified and as directed. |
| 79 | Supply and fix Godrej pattern mild steel cup board with shutter made out of 18 guage M.S. sheet60cm depth sides incl with back & 3 shelves & vertical partition & mild steel door shutter two leaves with frame, incl necessary fittings with locking arrangement and handle etc all as per Godrej Pattern with duplicate keys including necessary fittings & two coats of spray painting over a coat of red oxide zinc chromate primer complete.The cupboard to be fixed to wall with 6 Nos of hold fasts of 25 x 3mm flat iron, 15cm long. The cost of hold fasts& grouting them in CM (1:3) is deemed to be included in unit rates (Only front face of cupboard to be measured)complete all as specified and as directed. |
| 80 | M&L for Steel Work in Tubular Trusses including Special shaped Washer etc. complete using ERW or Induction Butt Welded Tubes, confirming to IS-1161-1979 Grade-240, complete all as specified and as directed. |
| 81 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 82 | M&L for Cleaning and removing all Scales and dirts from the Tank and mouths of circulating Pipes, etc. after draining out Water from the Tank of capacity exc. 250 Litre and not exc. 500 Litre, cleaning the Tank by scrubbing the deposits with Wire Brush, re-fixing Inlet and Outlet Pipes in the Same Position and writing Letters \"CLEANED ON DD.MM.YYYY\" (i.e. Date of Cleaning of Tank) not exc. 50mm in height, complete all as specified and as directed. |
| 83 | M&L for Cement Concrete 1:2:4 (20mm graded stone aggregate), 40mm thick in Path/ Hardstanding in alternate Bay/Panel, finishing Cement Concrete Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed. |
| 84 | S&F rotational moulded polythene, triple layers, water storage tank 500 Ltr capacity, closed top, cylindrical, hoisted and fixed in position incl S&F 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed incl Dismantling water tanks Exc 250 Ltr & not exceeding 500Ltr complete all as specified and as directed. |
| 85 | M&L for concealed stop cock brass, chromium plated adjustable wall flange for bathroom fittings all as specified and as directed. |
| 86 | Taking down carefully copper/aluminium point wiring (light, Fan, Socket or power) fitting such as switches, ceiling roses, pendents, regulators, sockets etc complete removing material to store for keeping in safe custody and making good disturbed surfaces of walls, floors etc complete all as specified and as directed. |
| 87 | Taking down carefully by unscrewing from theboards/outlets boxes fittings and fixturessuch as switches, sockets ceiling, rose, lamp holders, tube light fittings, regulators etc and making good of disturbedsurfaces complete all as specified and as directed. |
| 88 | Taking down ofexisting old unserviceable submain wiringcomplete all as specified and as directed. |
| 89 | Taking down ofexisting old unserviceable MCB of any ratingcomplete all as specified and as directed. |
| 90 | Taking down ofexisting old unserviceable distribution boardof any type complete all as specified and as directed. |
| 91 | Material & Labour for concealed point wiring with single core PVC insulated and unsheathed 1100 volts grade cable with multistranded copper conductor of size 1.5 Sqmm nominal area drawn through & including non metallic rigid PVC conduit (circular/flat pvc conduit), medium duty not less than 20 mm dia concealed in wall/fixed on wall/ceiling with GI saddles , GI screws , rawl plugs with all fittings including tees , junction boxes & provision for modular box and modular cover of suitable size for mounting modular switches , sockets & regulators & drawing through continuous earth wire of PVC insulated unsheathed 1100 volts grade cable with copper conductor solid conductor of size 1.5 sqmmcomplete all as specified and as directed for the following:-Note: Cost for cutting chases and making good to match the existing surface shall be deemed to be included in the quoted rate. |
| 92 | For one light point controlled by one single pole switch & socket. |
| 93 | For one fan/exhaust/wall mounted point controlled by one single pole switch. |
| 94 | For one 3 pin sockets outlet 5 Amps on the same board with other switches with cable of size 1.5 sqmm. |
| 95 | For 3 pin socket outlet 5Amps independent with cable 1.5 Sqmm size. |
| 96 | For one 3 pin sockets outlet 15 Amps idependent with cables 2.5sqmm size. |
| 97 | All as per item No 91.00 above butsocket outlet indepen dent but below the switch board of light points in the same vertical plane, with cables.2.5 sq. mm size. |
| 98 | One bell/ buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sq.mm size. |
| 99 | Supply and fix in replacement of switch piano, flush type single pole, one way, 5 Amps, 240 volts complete all as specified and as directed. |
| 100 | Supply and fixing in replacement of socket outlet, 3 pin 5 Amps complete all as specified and as directed. |
| 101 | Supply and fix in replacement ofswitch piano, flush type single pole, one way, 15 Amps, 240 volts complete all as specified and as directed. |
| 102 | S & FSocket outlet piano type 2 in 1, 3 pin, 5 and 15 amp flush typetype universal complete all as specified and as directed. |
| 103 | Supply & Fixing of Ceiling Rose, 3 phase polycarbonate isolated body complete all as specified and as directed. |
| 104 | S&Fsteped type electronicfan regulator flush type on the existing phenolic laminatedsheet etc complete all as specified and as directed. |
| 105 | Supply & Fixing of Buzzer, Ding Dong AC. 230 volts, single polecomplete all as specified and as directed. |
| 106 | Supply and fixing in replacement of unsvl lights LED lights fitting 1x 16W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 107 | M&L for Removing and refixing LED tube lights fitting of any capacity, 220V, AC decorative box type after cleaning with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 108 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 109 | S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 110 | S&F in repair bracket made of GI pipe light grade 40mm bore bent to shape as required at site for street light fitting 1.2 m in length and fixed on wall/pole including necessary MS clamps, nuts, bolts etc complete all as specified and as directed. |
| 111 | S&F submain wiring withunsheathed multi-stranded FR Grade copper conductor cable 1100 volts grade drawn through in and including PVC rigid conduit medium grade of not less than 20mm dia with conduit accessories and concealed in wall/surface of ceiling for two runs of 4 Sqmm single core HR Grade and one run of 2.5 Sqmm PVC insulated copper conductor for earth continuity wire between main DB to Sub main DB/ AC plug points complete all as specified and as directed.Note :- Two run of single core cable with one run of earth continuity conductor and PVC conduit and accessories will be measured as one length including cutting chasing in wall complete all as specified and as directed.Note: Rates are deemed to be included for chases of conduit and sunking for boxes cutting and making holes in wall/floor for passing in or through conduit. |
| 112 | S&F submain wiring withunsheathed multi-stranded FR Grade copper conductor cable 1100 volts grade drawn through in and including PVC rigid conduit medium grade of not less than 25mm dia with conduit accessories and concealed in wall/surface of ceiling for two runs of 4 Sqmm single core HR Grade and one run of 2.5 Sqmm PVC insulated copper conductor for earth continuity wire between main DB to Sub main DB/ AC plug points complete all as specified and as directed.Note :- Two run of single core cable with one run of earth continuity conductor and PVC conduit and accessories will be measured as one length including cutting chasing in wall complete all as specified and as directed.Note: Rates are deemed to be included for chases of conduit and sunking for boxes cutting and making holes in wall/floor for passing in or through conduit. |
| 113 | Supply and fixing Rigid non-metallic 20 Dia in mm PVC conduit exclusive of boxes (junction/terminal) but inclusive all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and as directed. |
| 114 | Supply and fix in replacement of factory made epoxy polyster powder coated distribution board SP&N 8 way fabricated from minimum 1.6 mm thick CRCA sheet with double door (IP-43 protection) fixed flush to wall and standard DIN rail, earth bar and cable ties for cable management, suitable for one incomingand 6 outgoings complete all as specified and as directed.Note: Cutting on wall and taking out old one and then flushing new DB and making all the connection as before and any accessories required to fix the DB including making good the disturbed surface is deemed to be included in quoted rate. |
| 115 | S&F in repalcement of MCB SP 6-32 Amps ,10 KA 230 Volts ,50 HZ complete all as specified and as directed. |
| 116 | RemovingSP 6-32 Amps MCB from old existing distribution board and refixing after cleaning old MCB in new distribution board complete all as specified and as directed. |
| 117 | S&F in repalcement of MCB SP 40 Amps ,10 KA 230 Volts ,50 HZ complete all as specified and as directed. |
| 118 | Supply and Fixing of modular switches 1 way, 6 Amp 1 module complete all as specified and as directed. |
| 119 | Supply and Fixingmodular Socket, 6A - 2/3 pin combined 2 module, complete all as specified and as directed. |
| 120 | Supply and Fixing of modular switches 1 way, 16 Amp 1 module complete all as specified and as directed. |
| 121 | Supply and Fixingmodular Socket 6A/16A - 2/3 pin combined 2 module, complete all as specified and as directed. |
| 122 | S&FGI Modular gang sunk-in pressedterminal boxes of required size not less than 1.2 mm thick factory made for following module complete all specified and as directed of the following sizes:-. Note: Flushing of module box in wall with cement and repairing the wall as before is deemed to be included in quoted rate. |
| 123 | Metal flush box 1/2 module. |
| 124 | Metal flush box 3 module. |
| 125 | Metal flush box6 module. |
| 126 | S&F white cover plate with frame of following module complete all specified and as directed of the following sizes:-. |
| 127 | white cover plate with frame 2 module. |
| 128 | white cover plate with frame 3 module. |
| 129 | white cover plate with frame 6 module. |
| 130 | S&F Single pole and neutral enclosure with a two pin and earth including plug and socket complete set with one single pole MCB of 20 Amps,complete all as specified and as directed. |
| 131 | Supply and fix in replacement of factory made epoxy polyster powder coated distribution board Triple pole and neutral 4 way 415V fabricated from minimum 1.6 mm thick CRCA sheet with double door (IP-43 protection) fixed flush to wall and standard DIN rail, earth bar and cable ties for cable management, suitable for one incomingand 6 outgoings of the following sizes:-.Note: Cutting on wall and taking out old one and then flushing new DB and making all the connection as before and any accessories required to fix the DB including making good the disturbed surface is deemed to be included in quoted rate. |
| 132 | Supply and fixing 32 Amp 415V 10KA \"B\" curve miniature circuit breaker (MCB)of four poles and current carrying capacity in the DB complete with connection testing and commissioning of the following sizes:-. |
| 133 | Taking down ceiling fan (C/F of any size/make), cleaning its dust properly oiling and hanging the same back to its original position including connecting the wire to ceiling rose etc complete after completing the wiring complete all as specified and as directed.Note :- (i) The spares like cotter pin, nuts & bolts, connecting rods & hooks etc if found defective/damage deemedto be replaced and make the ceiling fans functional. No extra payments will be done on this account. |
| 134 | Taking down exhaust fan & wall mounting and re-connecting up including provision of cable from ceiling rose to exhaust fan after cleaning all dust complete all as specified and as directed.Note :- (i) The spares like nuts & bolts etc if found defective/damage deemed to be replaced and make thefans functional. The rates quoted for the same deemed to be included for the above job. |
| 135 | M&L for Rewinding the stator complete with super enamelled bare copper conductor with the same size and number of turns as that of the old oneinsulating, varnishing and pre heating complete all as specified and as directed for the following :Note: Rates are deemed to be inclusive of replacing bush, bearing, armature & capacitor of any type, size & capacity, if required as per fan condition. |
| 136 | (a) Ceiling fan 1200mm/1400mm sweep. |
| 137 | (b) Exhaust fan 250mm upto 300 mm sweep. |
| 138 | (c ) Exhaust fan above 300mm upto 450mm sweep. |
| 139 | (d) Wall mounted fan upto 300mm sweep. |
| 140 | Supply and fixing capacitor of 3.15 MFD complete all as specifeid and as directed. |
| 141 | Supply and fixing capacitor of 2.5 MFD complete all as specifeid and as directed. |
| 142 | Supply and fixing louvers of Exhaust fan of metal body of size 250mm upto 450mm sweep and removing the old, damaged and corroded exhaust fan louverswith new one, complete all as specified and as directed. |
| 143 | Supply and fixingblades of Exhaust fan of metal body of size 250mm upto 450mm sweep as per site and removing the old damaged & corroded exhaust fan bladeswith new one, complete all as specified and as directed. |
| 144 | Supply and fixingExhaust fan support arms, nut bots & washer for exhaust fan of size upto 450mm sweep of any type & size as per site , complete all as specified and as directed. |
| 145 | M&L for Cleaning and preparing the surfaces of ceiling fan, wall mounted fan, exhaust fan, pedestal fan, removing the grease, carbon dust over the fans and painting with two coats of synthetic enamel paint of approved colour with brush painting and writing MES number on the fan of suitable size complete all as specified and as directed. |
| 146 | M&L for Disconnecting the inlet , outlet , water connections and electric supply , taking down of Geysers (water heater) of capacity 25/ 50 Ltrshorizontal/vertical of any make/model from existing position andcarrying out descaling of inner container , cleaning with suitable chemicals and materials , washing withfresh water, replacment of defective/unserviceable components if any and fixed to its original position complete all as specified and as directed.Note: The rate quoted shall include the minors repairs and replacement of minor parts i.e. screw nuts, bolts washers etc .The items replacing herein after shall be measured and paid seperately. |
| 147 | Supply and fixing geyser inner storage tank made of stainless steel of capacity 25Ltrs, complete all as specified and as directed.Note :- Sample shall be checked at site before procurement to match the existing models. |
| 148 | Supply and fixing heating element 2.00 KW capacity 230 volt suitable for geysers any type ( round/triangular)as per site requirement ISI mark complete all as specified and as directed. Note :- Sample shall be checked at site before procurement to match the existing models. |
| 149 | Supply and fixing thermostat 7\"/11\" suitable for storage type water heater complete all as specified and as directd. Note :- Sample shall be checked at site before procurement to match the existing models. |
| 150 | Supply and fixing PVC insulated PVC sheathed 3 core 4.00 sqmm copper conductor flexible sheathed cable suitable for geysers of any size complete all as specified and as directed. |
| 151 | M&L for preparing external surfaces of water heater, cleaning with emery paper & cloth and painting with two coat of synthetic enamel paint of white colour of approved make with brush and writing MES No. on it of suitable sizecomplete all as specified and as directed. |
| 152 | Supply and fixing Geyser assembly suitable to fix thermostat, heating elements as of the existing size including number nuts, bolt, washer as per site requirement etc complete all as directed. Note :- Sample shall be checked at site before procurement to match the existing models. |
| 153 | Taking down old existing unserviceable geysers of any capacity from its position, dismantling and taking out hot water tank, soldering/bracing to arrest the leakage, removing geyser outlet/inlet pipe blockages by removing deposited sediments in geyser tank, reassembling and fixing back in position and testing complete all as specified and as directed. Note :- Items required for repairs to geysers such as heating elements, thermostate etc shall be measured and paid separately relevant itmes. |
| 154 | Supply and fixing Bottom inspection chamber cover suitable for 25 Ltrs capacity geyser of any make/model complete all as specified and as directed. |
| 155 | Supply and fixing Indication lamp (red & green) suitable for geyser in round/rectangular shape complete all as specified and as directed. |
| 156 | Supply and fixing of PVC connections 15mm size with PTMT nuts of length 450mm suitable for hot water complete all as specified and as directed. |
| 157 | Material,labour and shifting of existing electric energy meter incl fixing/consealedof new meter steel boxof size 270x225x135 mminside the wall and fixingthe meter inside the box incl connection of inccomming and outgoing cablewith all fitting acessaries complete all as specified and as directed. |
| 158 | Supply and fixing in replacement of defected/unsvl electronic meters temper proof LCD display with polycarbonate cover 230 V, 10-60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH complete all as specified and as directed. |
| 159 | Supply and fixing in replacement of three phase defected/unsvl electronic meters temper proof LCD display with polycarbonate cover 415 V, 10-60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH complete all as specified and as directed. |
