Bhubaneswar Development Authority-BDA has published Tender For Providing Furniture And Partition Wall To Inter State Bus Terminal At Baramunda, Bhubaneswar. Submission Date for this Tender is 16-10-2023. Dustbin Tenders in bhubaneswar Odisha. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | SEAT ASSEMBLY: The seat is made up of 1.5±0.1 cm thick hot-pressed plywood upholstered with fabric and moulded polyurethane foam.SEAT SIZE: 51.8cm (W) x 49.7cm(D) .BACK ASSEMBLY: The Back is injection moulded in glass filled Polypropylene which is 2 upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 10.1 cm.BACK SIZE: 47.9 cm(W) x 66.9 cm (H)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seatfoam is moulded with density 45+/-2 kg/m and hardness 14 ± 2 kgf as per IS:7888 for 25% compression.ARMRESTS (ADJUSTABLE):The height adjustable armrest is made of Polypropylene and can be adjusted to 6.010.1cm height it also has swivel and To and Fro adjustment with moulded PU armtopACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features360° revolving type Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfortTill tension adjustment can be operated in seating position5 position Tilt limiter giving option of variable sit angle to the chairSeat/back tilting ratio of 1:2 The mechanism housing is made up of HPDC Aluminium & black powder coated (DFT 40 to 60 micronPNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with an adjustment stroke of 10.0±0.3cm.PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 166.1±0.5 cm.(76.1 ± 1.0 cm. with castors).TWIN WHEEL CASTORS: The twin wheel castors are Injection moulded in black Polyamide having 6.01 0.1cm wheel Diameter. (Make - Herman Miller / Steelcase / Godrej) WIDTH (W) - 76.0cm DEPTH (D) - 76.0cm HEIGHT (H) - 95.5 cm- 105.5cm SEAT HEIGHT - 43.5 - 54.0cm |
| 2 | Trident Junior 1 Main Desksize shall be1200 Widthx 600 Depthx 743 Height . Top shall be of 18 mm thickness made of PLT board with 2 mm Edge banding. Wenge and savannah Maple PLT board shall be used. The Understructure shall be in pre-laminated panels made with PLT boards . 2- Drawerand 3 - Drawer storage units with different combinations to support tops made with 18 mm PLT boards of different colours.Modesty and back panels made with 18 mm PLT boards. The pedestals / storages shall be fitted with necessary locks. (Make - Herman Miller / Steelcase / Godrej) |
| 3 | Mayfair Main Table with Footrest - Godrej Make Mayfair Main Desk size shall be 900 Width x 600 Depthx 750 Height. The Top shall be in white cedar and black and shall be 18 mm PLB with PVC lipping.The side panels shall be 18 mm thickPLT with PVC .The Modesty panel shall be 18 mm thick PLT.The Modesty panel shall be in a combination of black & white cedar. (Make - Herman Miller / Steelcase / Godrej) |
| 4 | SEAT ASSEMBLY: The seat should bemade of Injection molded Plastic outer & inner. Plastic Inner should beupholstered with fabric and moulded Polyurethane foam of Density 67±2 kg/m³,and hardness load 16 ± 2 kgffor 25% compression. Seat SIZE : 46.0 cm. (W) x 48.0 cm. (D) NET HIGH BACK ASSEMBLY(3102AM): The Back should bemade 3.5±0.03cm x 1.5±0.02cm x 0.2±0.016cm of MS ERW oblong Tube . It should beupholstered using Net fabric with high tenacity yarn. BACK SIZE (For 3102AM): 43.0 cm. (W) x 60.0 cm. (D) BACK HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should bemoulded in Density 67±2 kg/m³, and hardness load 16 ± 2 kgffor 25% compression. ARMRESTS (ADJUSTABLE): The armrest top should bemoulded from polyurethane(PU) and mounted on to a drop liftadjustable type tubular armrest support made of Ø3.81±0.03 cm x 0.2±0.01 cm thk MS ERW tube. The armrest height should beadjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should bedesigned with the following features: . 360° revolving type. . Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. . Tilt tension adjustment can be operated in seating position. . 5-position Tilt limiter giving option of variable tilt angle to the chair. . Seat/back tilting ratio of 1: 2 . The mechanism housing should bemade up of HPDC Aluminum black powder coated. SEAT DEPTH ADJUSTMENT: Seat depth adjustment should beintegrated in the seat through a sliding mechanism. Seat depth adjustment range should beof 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT (FOR 3102): Back Frame should beconnected to the Up/Dn mechanismhoused in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT: The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY:The pedestal should beinjection moulded in black 33% glass-filled Nylon 66 and fitted with 5 nos. twin wheel castors. The pedestal should be66.1±0.5 cm pitch-center dia.(76.1±1.0 cm. With castors.)TWIN WHEEL CASTOR:5 Nos. twin wheel castors should beinjection moulded in Black PP having 6.0±0.1cm wheel Diameter and assembled to pedestal. (Make - Herman Miller / Steelcase / Godrej) |
| 5 | SEAT ASSEMBLY: The seat assembly should bemade up of 1.2 ±0.1cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The back asembly. should bemade of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should beupholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm. (W) x 60.5cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should bemoulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgffor 25% compression. ARMRESTS: The one-piece armrests should beinjection moulded from black Co-polymer Polypropylene. . TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should becantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. (Make - Herman Miller / Steelcase / Godrej) |
| 6 | Construction & Material - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990 Soft closing Hinge. Handle - Asthetically appealing handle made of Aluminum Cam Lock - -3 Way locking provision. - Click action mechanism. - Key removable in locked and unlocked positions. - Zinc alloy die cast housing. (Make - Herman Miller / Steelcase / Godrej) |
| 7 | Width 295 mm Length 905mm Height 31mm No of bend 6nos Sharp edges No sharp edges in loading side Mfg Process Press formed Usage Decking surface Fasteners 8nos of M8x20 Surface finish Powder coated Profile Angle Angle type 40 x 40 mm Number of bend 1no Panel adjustability 19.05mm Material Quality Min Ys= 255 Mpa Mfg process Roll forming Finish Powder coated Material Steel Usage Stability Qty per system 8nos Mfg process Press forming Fasteners 2 nos of M8x20 Surface finish Powder coated (Make - Herman Miller / Steelcase / Godrej) |
| 8 | SIDE FRAME ASSEMBLY: The side frame assembly should befitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It should bemade of 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick cmx0.16cnn and black powder coated ( DFT 40-60 microns ). The ends should befitted with ABS moulded end caps.TIE MEMBER: It should bethe connecting beam assy. which holds the two side frames to each other. 2 nos. tie members should beused to connect the side frames. The tie-member should beof 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick cm x 0.16cm and black powder coated ( DFT 40-60 microns ). The seat/back assemblies should bemounted on one of the tie-member which has 5.0 ±0.1cm x 5.0 ±0.1 cm x 0.5 ±0.1cm. thk -- 5.5 ±0.1cm Long MS. Std. angles welded to mount the seat and back.SEATREST ASSEMBLY:The seat rest assembly consshould be ts of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45 +1- 2 Kg/m3 with Hardness load 25 ± 2 kgffor 25% compression of the foam. The complete moulded seat rest assembly should becovered with a replaceable fabric upholstery cover*SEAT SIZE: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T) BACKREST ASSEMBLY:The backrest assembly should beflexing type and consshould be ts of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density = 45 +1- 2 Kg/m3 with Hardness load 14 ± 2 kgffor 25% compression of the foam. The complete moulded backrest assembly should becovered with a replaceable fabric upholstery cover. *BACK SIZE: 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T) ADJ. GLIDES: The adj. glide should beinjection moulded in black Nylon & fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take cshould beor unleveled floor surface. (Make - Herman Miller / Steelcase / Godrej) Overall Dimensions of ChairSeat Height - 43.5 cm.Height - 78.5cm.Width & Depth of Chair as- Width-60.5cm and Depth-70.0 cm. |
| 9 | Troika Corner Table - Natural Wood Dimensions Diameter - 524 mm Height - 547 mm Material : Powder coated MS legs The top is MDF with Oak veneer (Make - Herman Miller / Steelcase / Godrej) |
| 10 | Over allouter dimension is(L) 2025mm x (W)760mm x (H) 550mm. Head board and foot board have curved profileat the top made of MS ERW round tubes of thickness 1.2mm & dia 31.75 mm. Head board and leg board is further strengthened by 3 vertical pipes eachof thickness 1.2 mm and dia of 19mm &1 eachHorizontal pipe of thickness 1.2mm and dia of 25.4mm of equal height. Lying surfaceis made of8 bend panelof CRCA sheet of thickness 0.80mm mm. This 8 bend panel is further strengthened on thelongitudinally edges by welding full length with the help of C shaped metal channel section. Middle of 8 bend panel is strengthened by 5 L shaped stiffeners. lying surface is strengthened bytrapezoidal contour (rounded corner) 10 nos, embossed cut out. All metal components is pre treated with zinc phosphating and then powder coated with epoxy polyester powder coating. Goods are supplied in knocked down construction to reduce carbon emission. To ensure quid quality welding " Co2 Argon"process is adhered to. Neoprene rubberwith reinforced metal washer is used for leg shoes. Head board and leg board are connected to mattress platform thru L bracket at 4 corners to ensure rigidity, with the help ofzinc plated screws. Maximum safe working load is 135 kg. (Make - Herman Miller / Steelcase / Godrej) |
| 11 | Hero Mat 78 36 4 Thickness 50 mm.Quilting Material-PU Foam.Density of Quilting Material (± 2 Kg/m3)-18 Kg/m3.Mattress Top-Box Type. Cover-Fabric Composition-Polyester.MATTRESS COVER-Printe (Make - Herman Miller / Steelcase / Godrej) |
| 12 | Size ( in cm) : 43 x 69 Fibres : 15 Dn Conjugated silconized Fabre weight - 650 Fabric- Flower Embossed 90 GSm Polyester Packaging - Nonwoven Fabric Packaging(Make - Herman Miller / Steelcase / Godrej) |
| 13 | Overall Dimension: Overall Sizes Diagonal LegDia 538 mmH470 min-655max. Top platemade of SS 304 made sheet with spin section of thickness 1mm & non corrosive. It has a diameter of 305mm, seat basemade of MS ring and rectangular tube. EN8 Screw having dia of 22 mm is used for height adjustment of the seat base. The round hubmade of MS ERW tube having dia of 38mm and thickness 2 mm.The Hub is welded with the legs and itaccommodate and cover the lead screw mechanism.The under-structure consist of 4 legs made up ofMS ERW tube of diameter 25.4 mm and 1.6mm thick. The press formed pipe leggive a round & clean look. All the legs is Provided with 4 nos of Nylon-6 bush. All metal componentsare pre treated with zinc phosphating in 7 tank process and then powder coated withepoxy polyester powder coating. Safe working load is 135kg (Make - Herman Miller / Steelcase / Godrej) |
| 14 | Overall dimension is 2005 mm (L) x 666 mm (W) x 830 mm (H). It is a removable stretcher on trolley mounted on castors.. The trolley is made of 31.75 mm & 25.5 mm dia 1.6 mm thick & 1.6 mm thick ERW tube. The castors are 200 mm dia diagonal lockable castors. The stretcher under structure should be made of 25.4 mm dia 1.6 mm thick ERW tube and the top is made of 1.2 mm thick CRCA sheet. The stretcher has a Provision to mount IV pole at two corners. The product is pre treated and powder coated with Epoxy polyester powder coating. (Make - Herman Miller / Steelcase / Godrej) The maximum load bearing capacity is 135 kg. |
| 15 | Over all dimension is (L) 790mm x (W) 600mm x (H) 870mm foldable frame structure is made of section 22x1.2mm A3 carbon steel with chrome finish. Cross barmade of A3 carbon steel with section 25.4 x 1.2mm. The Rear wheel is made of 24 inch Solid mag wheels with alloy in the rim . Integrated hand rim is Provided to drive the wheel chair of section 16x1.2mm A3 carbon steel with chrome finish the front wheel is of 8 inch HUB made of PA polymer and outer with solid rubber PU molded arm rest & base made of ABS for better arm support there is Leatherite strap for calf rest & Leatherite cushion for seat the foot rest is Adjustable aluminium die cast foot rest with up down & swivel type mechanism Push Handles is made of molded rubber grip to push the wheelchair Hand brakes is Provided to lock the wheelchair at desired location. structure is made of MS withAnti rust chrome finish safe working load is 100kg (Make - Herman Miller / Steelcase / Godrej) |
| 16 | Telescopic height adjustable saline stand mounted on castor. Over all dimension is 652 mm dia base circle with ht adj from 1655 mm to 2365 mm. The 5 prong bottom frame is of 1.6 mm thick stainless steel and the lower basement made of 31.75 mm dia with 1.6 mm thick ss tube. Five nos.high endurance anti static plastic molded 50 mm castors are Provisionided with dual locking. The telescopic rod is 19 mm dia , 1.6 mm thick SS 304 grade tube with locking knob. 2 nos hooks are Provisionided for hanging saline bags. The telescopic tubehave plastic bush at the bottom which Provisionide smooth linear motion during ht adjustable. (Make - Herman Miller / Steelcase / Godrej) |
| 17 | Overall dimension: L 2637XW 647.5 x h1720 MM. Frame is made of ERW tube with movable plastic hinges. The fix frame is made of 25.4 mm dia 1.2 mm thich ERW tube, the movable frame is made of 19.05 mm dia 1.2 mm thich ERW tube and the leg frame is made of 30 mm suqare tube with 1.6 mm thick. The fixed portion is1075 mm width and the movable portion is 778 mm width. 50 mm dia wheel castors are Provisionided. All MS parts are powder coated with thermosetting epoxy polyester.Green color Casement fabric are to be provided for modesty. (Make - Herman Miller / Steelcase / Godrej) |
| 18 | Advanced Medicine cart constructed of CRCA Powder Coated MS Sheet of thickness 1.2mm. overall dimension of L 996 W x 625 H x 1550 mm. ABS grade made top sheet with 3mm thickness should be used. Should have 7 drawers with drawer configuration: 6 small (390(L)x600(W)X71(H)mm) + 1 Large (390(L)x600(W)X227(H)mm).all drawers should be lockable through central locking. Should have anti-tilt mechanism. should have 7 drawers with medicine bins/containers & adjustable acrylic separators.Should have key lock type central locking mechanism for drawers. Should have sharps container – 2qty., push/pull writing surface, utility tray, document holder, catheter holder, Tilt bins mounted on top for storage, SS Bridge shelf for keeping daily use items handy, ABS vacuum formed top tray of thickness 3mm, Aluminum push handle of dia. 25mm built into the end panel for smooth stable movement. Integrated pullout writing surface top. Trolley should be light, sturdy, scratch and dent resistant. , should have a waste bin discarding syringes and gloves, should have 4 TPE corner bumpers for collision protection, Single wheel front locking castors should have 125mm diameter to facilitate quiet and easy movement.Aluminum handle pipe should have section of 25mm with length of 365mm & should have thickness of 1mm giving a glossy finish. Thermosetting epoxy polyester with semi-gloss finish powder coating must be used. Safe working load must be 47kgs. Optional accessory: Oxygen cylinder holder (Make - Herman Miller / Steelcase / Godrej) |
| 19 | Overall dimension is 665 mm (L) x 485 mm (w) x 393 mm (H). Under structure frame is made of 19 mm x 19 mm and 1.2 mm thick vertical tubes. The stool top is made of 1.2 mm thick . The step top have 3.2 mm thick rubber sheet to have better grip. load bearing capacity is135 kg. all the metal parts are pre treated and powder coated with epoxy polyester powder coating. (Make - Herman Miller / Steelcase / Godrej) |
| 20 | MS Oxygen cylinder trolley suitable for B type oxygen cylinder. The overall dimension are 410 mm (L) x 388 mm (W) x 1112 mm (H).The main frame is made of 25.4 mm dia 1.6 mm thick ERW tube with 10 mm dia ms make locking rod to keep the cylinder position during transit. The trolley is Provided with 100 mm dia 25 mm thick PU wheel for longer durability. LDPE make leg bush is Provisionided on the legs. Max load bearing capacity is 50 kg. (Make - Herman Miller / Steelcase / Godrej) |
| 21 | Primary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Softclosing access flap with in-build power box are provided on work surface for wire management. Secondary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Under- structure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security. Back Unit Top Panel:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Slide Door Unit:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. Display/Storage Unit:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side,back and shelves.Doors are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Top panel of display unit Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top (Make - Herman Miller / Steelcase / Godrej) |
| 22 | SEAT/BACK ASSEMBLY:The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The NetBack should bemade up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should bemoulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgffor 25% compression. BACK SPINE: The support spine should bemade up of High Pressure Die cast polished hed Aluminum. ARMRESTS : The armrest should behaving two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should beprovided in Aluminum structure of armrest which should beconnected to Aluminum Back spine and should beoperated by button. The depth adjustment should beprovided in pad which should befixed to armrest structure. Armrest Top should bemade up of PU molded over plastic inner.ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort • Tilt tension adjustment can be operated in seating position • 5 position Tilt limiter giving option of variable tilt angle to the chair • Seat / back tilting ratio of 1:2 • The mechanism housing should bemade up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron)SEAT DEPTH ADJUSTMENT: Seat depth adjustment should beintegrated in the seat through a sliding mechanism. Seat depth adjustment range should beof 3.75±0.1 cm LUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consistof lumbar spine (material-Glass Fiber Filled Nylon) which should befixed toAluminum Back spine. The Lumbar pad (material- Poly Propylene) should befixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustment of 5.0±0.5cmPNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm. PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should beHigh Pressure Die cast polishedAluminum and fitted with 5 nos. twin wheel castors. The pedestal should be65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS:The twin wheel castors should beinjection moulded in black PP having 6.0± 0.1cm wheel Diameter. The neckrest assembly consshould be ts of upholstered Neckrest inner(material-PolyPropylene) with moulded Polyurethane foam and Polyster fabric.Upholstered inner should befixed to Neckrest cover.Neckrest should befixed to Back assembly through Neckrest spine .Neckrest assembly has height adjustment of 5.5 +/- 0.5cm and Rotation adjustment of overall 20° +/- 2° (Make - Herman Miller / Steelcase / Godrej) Overall Dimensions of Chair Seat Height - 45.5-55.5cm. Height - 109.3 - 124.4cm. Width-75.0 cm and Depth-75.0 cm |
| 23 | EAT/BACK ASSEMBLY:The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The NetBack should bemade up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should bemoulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgffor 25% compression. BACK SPINE: The support spine should bemade up of High Pressure Die cast polished hed Aluminum. ARMRESTS : The armrest should behaving two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should beprovided in Aluminum structure of armrest which should beconnected to Aluminum Back spine and should beoperated by button. The depth adjustment should beprovided in pad which should befixed to armrest structure. Armrest Top should bemade up of PU molded over plastic inner. ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort • Tilt tension adjustment can be operated in seating position • 5 position Tilt limiter giving option of variable tilt angle to the chair • Seat / back tilting ratio of 1:2 • The mechanism housing should bemade up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron) SEAT DEPTH ADJUSTMENT: Seat depth adjustment should beintegrated in the seat through a sliding mechanism. Seat depth adjustment range should beof 3.75±0.1 cm LUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consistof lumbar spine (material-Glass Fiber Filled Nylon) which should befixed toAluminum Back spine. The Lumbar pad (material- Poly Propylene) should befixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustment of 5.0±0.5cm PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm. PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should beHigh Pressure Die cast polishedAluminum and fitted with 5 nos. twin wheel castors. The pedestal should be65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS:The twin wheel castors should beinjection moulded in black PP having 6.0± 0.1cm wheel Diameter. (Make - Herman Miller / Steelcase / Godrej) Overall Dimensions of Chair Seat Height - min 45.5 to max 55.5cm. Height - min 95.5 to max 105.5 cm. Width & Depth of Chair as measured from pedestal - Width-75.0 cm and Depth-75.0 cm (Make - Herman Miller / Steelcase / Godrej) |
| 24 | SEAT/BACK ASSEMBLY:The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The NetBack should bemade up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should bemoulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgffor 25% compression. BACK SPINE: The support spine should bemade up of High Pressure Die cast polished hed Aluminum.. LUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consist of lumbar spine (material-Glass Fiber Filled Nylon) which should befixed toAluminum Back spine. The Lumbar pad (material- Poly Propylene) should befixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustment of 5.0±0.5cm TUBULAR FRAME (3012AX): The powder coated (DFT 40-60 micron) tubular frame should becantilever type & made of Ø2.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube. (Make - Herman Miller / Steelcase / Godrej) Overall Dimensions of Chair Seat Height - 48.5cm. Height - 99.5cm. Width-65.5 cm and Depth-58.2 cm (Make - Herman Miller / Steelcase / Godrej) |
| 25 | Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap along with a Gromett is provided on work surface for wire managementWire Management - Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8+3 Module cut out provision for Anchor Roma) which is fixed with worktop along the width at Access Flap position.Modesty Panel & Side Skirting - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Understructure - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping TOP shelf - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Hinge Door + Drawer unit - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. **Drawer bottom is made of 5.5thk MDF whiteboard Handle is provided for ease of opening. HDU and Drawer is provided with cam lock for security. Essential Accessories - Wire Riser made of 0.8mm CRCA (IS-513) is provided for proper wire management. (Make - Herman Miller / Steelcase / Godrej) Organizer Plate made of 1.2mm CRCA (IS-513) is provided for magnetic sticky notes. Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging. (Make - Herman Miller / Steelcase / Godrej) |
| 26 | The Omega planter has a 3-piece construction. The Outer-Shell, Inner-Pot, and Drain-Storage Tank (Capacity 4 litres) are all made from Fibre-reinforced plastic and finished with PU paint. The Drain-Storage Tank is connected to the Inner-Pot with Stainless Steel Bolts and Nuts. The opening from the Inner-pot into the drain-storage is covered with strainer. This shall prevent any large solid particulates from entering & clogging the Drain-Storage Tank. The Drain-Storage Tank can be emptied at regular intervals through an on/off valve nested in the Outer shell and connected using a flexible hose. (Make - Herman Miller / Steelcase / Godrej) |
| 27 | CaféPod with MDF/Rubberwood top PU Coated size shall be800 Widthx 800 Depth mm x 745 Height mm . Top shall be of MDF 25 mm thick size : 800 mm x 800 mm x 25 mm . Painted in yellow ,red,orange,wine,biege PU coating on a sealer coat . PU coating done on both top and bottom surfaces . PU coating has a hardness of 3H . Top is Fitted to the understructure with No. 8 x 16 plilip head screw . Understructure shall be foldable and stackable , made with combination of aluminium and plastic . Centre column is of Aluminium extrusion of diameter 70 mm , which is anodized . Base is made in 2 pieces of die cast aluminium with buffed finish . It is bolted together with centre column and top flange . (Make - Herman Miller / Steelcase / Godrej) |
| 28 | 1. SHELL : The single piece seat back shell is made up of injection moulded high impact strength glass filled polypropylene polymer compound (refer product catalogue for colour chart). * SHELL SIZE : 44.0 cm. (W) x 50.2 cm. (D) x 40.5 cm. (H) 2. POWDER COATED UNDERSTRUCTURE FOR LP-SM6 AND HS-1/2 :The powder coated (DFT 50±10 microns ) welded Beam M.S. Structure is made from Ø 1.2 cm MS Bright bar. The 0.16 ± 0.008 cm thk CRCA sheet is welded to tubes for fixing shell to the frame. The shoes made of Polypropylene polymer are fitted with frame. 3. GANGING SHOE(Option) : The shoes are made of Polypropylene polymer compound fitted with tubular frame as an accessory for LP-SM6 chair. (Make - Herman Miller / Steelcase / Godrej) |
| 29 | Trident Middle Main Deskwith ERU (RHS)size shall be1650 Width x 700 Depth x 743 Height (Main Desk) 1000 WidthX 450DepthX 743 Height (ERU).Top shall be of 18 mm thickness made of PLT board with 2 mm Edge banding. Wenge and savannah Maple PLT board shall be used. The Understructure shall be in pre-laminated panels made with PLT boards . 2- Drawerand 3 - Drawer storage units with different combinations to support tops made with 18 mm PLT boards of different colours.Modesty and back panels made with 18 mm PLT boards. The pedestals / storages shall be fitted with necessary locks.(Make - Herman Miller / Steelcase / Godrej) |
| 30 | Primary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Softclosing access flap with in-build power box are provided on work surface for wire management. Secondary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Under- structure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security. Back Unit Top Panel:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Slide Door Unit:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. Display/Storage Unit:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side,back and shelves.Doors are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Top panel of display unit Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top (Make - Herman Miller / Steelcase / Godrej) |
| 31 | Width - 1980 mm Depth - 830 mm Height - 835 mm Seat Height - 430 mm Upholstery • Material : Quilted Fabric • Shade : Dark Grey • Thickness : 1 mm Frame : • Material : Solid wood • Moisture content : 10 - 12 % • Thickness of Plywood used : 12 mm & 18 mm Seat Foam : • Material : Slab stock • Density : 32 kg/m3 at seat Back Foam : • Material : Slab stock • Density : 28 kg/m3 at seat Webbing : • Material : S spring Legs : • Material : PVC (Make - Herman Miller / Steelcase / Godrej) |
| 32 | Overall Size : Width:1450mm Depth : 850mm Height : 380mm TABLE METERIALS & SIZE : Top : Glass in beige shade . The glass is attached to the wooden frame via UV disc Structure : Rubber wood frame Drawers : High gloss PU paint in MDF in beige shade Construction: Knock down (Make - Herman Miller / Steelcase / Godrej) |
| 33 | Overall Size: Width- 970 mm Depth— 2046 mm Height -901 mm Material:Bed Structureconssst of metal frames made of M S. Channels in Imm Thickness.Horizontal plinths and bottom plinth are made of 25 mm Thick Prelaminated Particle Board 1S:12823 Class E1 (as per EN13986). Head board is made of 18 mm thick Prelaminated Particle board 1S:12823 Class E1 (as per EN13986) with all the exposed edges are edge banded with 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue.Tailboard is made of 18 mm thick Prelaminated Particle board 1S:12823 Class E1 (as per EN13986).Side rail is made of 18 mm thick Prelaminated Particle board 1S:12823 Class E1 (as per EN13986).Mattress panels of Bed are made of 18 mm thick Prelaminated Particle Board IS: 12823 Class E1 (as per EN13986) with all the exposed edges are edge bandedwith 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue.Hardware:The high quality hardware are used.Construction: Knock Down construction. Packets :2 packet.Finish :.18 mm thick Prelaminated Particle Board 1S:12823 Class E1 (as per EN13986)is in Imperial Oak shade. Lipping shade is 299P MAKE REHAU (Make - Herman Miller / Steelcase / Godrej) |
| 34 | Overall Size :Depth — 461.0 mm Width — 460.0 mm Height — 510.0 mm Material:Body panels of Bed side table are made of 18 mm thick Prelaminated Particle Board 1S:12823 Class E1 (as per EN13986) .All the exposed edges are edge banded with 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue.Drawer front are made of 18 mm thick Prelaminated Particle board 1S:12823 Class E1 (as per EN13986). Hardware:The high quality hardware used like Roller slides, Hinges , minifix, dowels is of make Hettich.Construction:Knock Down construction. Packets :1 packet.Finish :.18 mm thick PrelaminatedParticle Board 1S:12823 Class E1 (as per EN13986) is in Imperial Oak shade.Lipping shade is 299P MAKE REHAU (Make - Herman Miller / Steelcase / Godrej) |
| 35 | Width - 860 mm Depth - 830 mm Height - 820 mm Seat Height - 430 mm Upholstery • Material : Quilted Fabric • Shade : Dark Grey • Thickness : 1 mm Frame : • Material : Solid wood • Moisture content : 10 - 12 % • Thickness of Plywood used : 12 mm & 18 mm Seat Foam : • Material : Slab stock • Density : 32 kg/m3 at seat Back Foam : • Material : Slab stock • Density : 28 kg/m3 at seat Webbing : • Material : S spring Legs : • Material : PVC (Make - Herman Miller / Steelcase / Godrej) |
| 36 | The Move Up range of ergonomic height adjustable workstation aims at expanding the wellness portfolio and help clients create user centric solutions for offices. These ergonomic tables are an emerging trend in workspaces, with adequate wire management and multiplicity they are certain to replace the traditional office workstations.• Platform based system with Single and Double Motor Height Adjustable Leg options.• Multiple screen options.• Multiple configurations possibilities to support multiple activities• Accessories are incorporated for personalization of space. 1300 MM X 700 MM Worktop shall be made of 25MM thick Pre-Laminated Board conforming to IS: 12823.All the edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. Worktop support frames/cross member frame forms the understructure of the system, it connects the two legs and worktop is mounted onto this frame.• Worktop support frames is fabricated from 40 mm x 20 mm x 1.2mm thk MS tube (as per IS: 7138 ERW).• End Brackets LH/RH and Tube Connector for Worktop support frame are made from 3MM HR (as per IS: 2062).• Argo Shield welding is used for fabrication• There are always two cross members in the frame for Recta Aisle/ B2B/ Single module out of which one is a straight member and other is a bent tube.• Accent Plate is made from 0.8mm thk CRCA (as per IS 513). It is stuck with End Brackets after powder coating by Double sided tape on either end. Legs of the Move Up system forms the part of under structure which allows the vertical movement of the workstation.• Legs along with its mechanism converts the rotary motion of the motor/driver which is controlled by a control box into linear or the vertical motion.• Legs basically consists of two sliding aluminum extrusions i.e. inner and outer extrusions (AL 63400 - WP). It houses a spindle which allows the smooth up-down movement of the table.• At junction of both the extrusions a special grade injection molded plastic part is housed for smooth sliding movement.• A tube clamp aluminum extrusion (AL 63400 - WP) is welded (TIG) to the outer extrusion of leg, for mounting the leg lateral members/connectors of B2B and Aisle leg.• Leg top bracket of 5 mm thk aluminum is fastened to the leg which supports the motor and worktop support frame.• Maximum stroke length of the leg is 450mm. The Worktop Screen with be of a ht of 6 inches from worktop with options in Fabric/Decorative Laminate/Fabric Pin up/ Fabric Magnetic Metal Modesty:It is made from 2mm AL sheet on to which aluminum stud is welded for mounting.• Modesty is mounted on the worktop mounted bracket which is fixed on the worktop. Return Modesty:• Return modesty is made from 2mm AL sheet. It fixed on the worktop through 2 mm thk Al bracket with screws. Snake Wire Holder:• It is made from 2mm thk CRCA (as per IS 513), fabricated by Argo Shield Welding. It is used to hold the vertebrae carrying wires. It is mounted on the leg with the help of grub screw. Vertebrae:• Vertebrae is an essential accessory provided for a clutter free wire management.• It is used for routing power and data cables from ground (grouting) to the switch mounting box and power box.• Vertebrae is made from injection molded plastic parts with metal end used for fixing. Leg Modesty:Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.• The pin assembly for Modesty is made from 5mm thk HR (as per IS 513) and Ø 7.5 MS rod (as per IS 432) is used as pin, fabricated by Argo Shield Welding.• The Modesty is held by Holder Bracket made from 5mm thk HR (as per IS 2062) and 2mm thk CRCA (as per IS 513) (Make - Herman Miller / Steelcase / Godrej) MONITOR ARM - FLANGE DUAL MONITOR Keyboard Drawer (Metal) 19" with Soft PAD with Mouse Tray CPU TROLLEY Access Flap - 300 mm (Brush) (Make - Herman Miller / Steelcase / Godrej) |
| 37 | Work Surface : Made of 36mm thick MDFone side prelaminate board conforming to IS14587: 1998 with 0.4mm PVC membrane pressed on to top and having chamfered edge. Full length access panel is provided with soft closing hinges inline with worktop edge. Worktop is available in various shapes as shown above. Understructure- The understructure consist of mixture of 18mm and 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. Modesty Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Wire Management An array of panels made of 0.8mm and 1.2 mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Cutout for Standard Anchor Roma 4 module is provided for electrical fittings in Straight two seater and single seater modules below access flap per seat. AV Details The table is equipped with Extron cables cubbies along with cable retractors as standard offering only for 1800mm head module, 2350mm head module, 150° head module and 165° head module. For straight two seater and single seater modules, provision to mount AV cables is provided (eg. HDMI,VGAA, etc). Only Corner 90°, 30° corner and 50° corner modules have provision for wire flow between adjacent tables. Additional Wirecover made of 0.8mm Thick CRCA, provided below worktop to conceal Microphone wires running from table top to wire tray. (Make - Herman Miller / Steelcase / Godrej) |
| 38 | Work top--Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Soft closing dual access flap provided for access to power supply and data cables. Understructure-The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. Wire Management-A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables(eg. HDMI,VGA-A,etc). (Make - Herman Miller / Steelcase / Godrej) |
| 39 | SEAT ASSEMBLY: The seat assembly should bemade up of 1.2 ±0.1cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The back asembly. should bemade of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should beupholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm. (W) x 60.5cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should bemoulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgffor 25% compression. ARMRESTS: The one-piece armrests should beinjection moulded from black Co-polymer Polypropylene. TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should becantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. (Make - Herman Miller / Steelcase / Godrej) |
| 40 | The Seat is made from high density self-skin PU foam reinforced with 3mm M.S. perforated sheet insert. The PU foam having density of 520±10 kg/m3 with a Shore "A" hardness of 55±5. Seat Size 52.0(W) *46.5(D) The Back is made from high density self-skin PU foam reinforced with 3mm M.S. perforated sheet insert. The Pu Foam having density of 520±10 kg/m3 with a Shore "A" hardness of 55±5. Back Size 52.0 cm (W)x 51.5 cm (H) Cross Beam made up of black powder coated M.S E.R.W. square tube of size 6.0±0.05cm x 6.0±0.05cm x 0.18±0.016cm thk fitted with polypropelene endcaps.Leg & Armrest are made up of powder coated High pressure Aluminium Die cast. Leg Are fitted with soft grip PVC level adjusting shoes. (Make - Herman Miller / Steelcase / Godrej) Width (W) = 165.5 cm Depth (D) = 66.5 cm Seat Height (SH) = 42.5 cm Height(H) = 87.0 cm |
| 41 | Dimensions - 10" X 14" Weight - 2.200 kg Material - NON MAGNETIC SS 200 SERIES Thickness - 0.4 mm MOQ - 1 Pack of 6 (Make - Herman Miller / Steelcase / Godrej) |
| 42 | RECTA WORKSTATIONS - 1500 x 600 Providing and placing WISH panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. Tiles: Combination of top tiles are fabric & fabric tackable. Bottom tiles - Plain metal. INTERMEDIATE BLOCKS Intermediate blocks are given in DL + DL finsh. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. legs -metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 600 mm Pedestals with legs - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. CPU trolley - with castors KBPT with mousetray - metal Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. RECTA WORKSTATIONS - 900 x 600 Providing and placing WISH panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. Tiles: Combination of top tiles are fabric & fabric tackable. Bottom tiles - Plain metal. INTERMEDIATE BLOCKS Intermediate blocks are given in DL + DL finsh. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. legs -metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 900 mm w x 600 mm CPU trolley - with castors KBPT with mousetray - metal Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. PARTTITION - PER SQM RATE Providing and placing WISH panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. Tiles: Combination of top tiles are fabric tile. Bottom tiles - Plain metal. INTERMEDIATE BLOCKS Intermediate blocks are given in DL + DL finsh. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. (Make - Herman Miller / Steelcase / Godrej) |
| 43 | Providing and placing WALLFULL HT panel based modular partition with thickness as 76 mm thk and ht - 3000 MM till fase cailing level. Structure: The main structure has combination of different Aluminum Sections made from Aluminum alloy 63400-WP and are powder coated with Epoxy Polyester or Anodized, varying in heights and widths to make a full height cabin up to3048 mm.The frame structure is made by joining different aluminium extrusions by means of brackets made of 3 mm Thk HR (IS-2062) and screws as per elevations defined by customer. DOUBLE SKIN: Combination of tiles are offered in GLASS. Wire management: Metal powder coated 100mm wide power posts are provided wherever required to make junctions of 2way 180deg with electrical switch mounting. DOOR - Door Frame Size - 2400x1050 - is made of Aluminum extrusions and can be offered in anodized finish as well as powder coated finish. SINGLE side opening Glass door is provided with hinged ,Handle for Door and top/bottom patches. The door is made of 10mm Thk clear Toughened glass (IS-2835).Standard Door Shutter Size: 2200 x 956 mm(actual) Note 2: SPECIFICATIONS OF FLOORING FOR THE FREE STANDING PARTITION :- GRADE OF PCC SHOULD BE MINIMUM OF M20 ( MIX RATIO 1:5:5:3) OR M25 (MIX RATIO 1:1:2). THE DIMENSION OF EACH PCC SHOULD BE 450 MM L X 300 MM W X 140 TO 150 MM HT AT THE MARKED LOCATION. ( MIX RATIO OF CEMENT: SAND: STONE). ALSO ELECTRICAL TRUNKING SHOULD NOT BE LAID BELOW THESE PARTITIONS. (Make - Herman Miller / Steelcase / Godrej) |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
