Supply Of Spares Of Coal Mills (Hp-1103) To Rgtpp, Khedar, Hisar On Annual Rate Contract Basis. , Supply Of Spares Of Coal Mills (Hp-1103)To Rgtpp Khedar Hisar On Annual Rate Contract Basis , Bearing Housing For Rc Feeder And Coal Mill Gt1651907 , Eccentric Bearing Housing For Rc Feeder And Coal Mill , Air Restriction Ring Large Size (Length Approx. 1800Mm, Width 60Mm, Thickness 28Mm) (1 Set= 8 Nos.) , Air Restriction Ring Small Size (Length Approx. 1800Mm, Width 35Mm, Thickness 28Mm) (1 Set= 8 Nos.) , Shroud Plate1360x120x10 (1 Set= 8 Nos.) , Roller Retainer Ring For Coal Mills Moc: 16Mn , Scrapper With Liner Plate Long, Moc:Is 1030, Gr-Ii, (Cast Steel) Moc Of Linear Iss 276 Astm Grade-3 , Scrapper With Liner Plate, Short, Moc:Is 1030, Gr-Ii, (Cast Steel)Moc Of Linear Iss 276 Astm Grade-3 , Journal Housing Liner Upper, Moc: Cast Steel As Per Is 1030 Grade-2 , Journal Housing Liner Lower, Moc- Ss-304 , Wearable Adjustable Shrink (Adjustable Orifice) For Coal Mill Hp-1103, Coal Pipeod-710Mm, Model-Smk Type-B (Wearable Adjustable Shrinks To Be Supplied With 2 No. Extra Flange For Connection/Installation With Pc Pipe) , Feeder Outlet Gate Without Actuator , Mill Body Deflector Support Plate Ms, 1 Set= 3 Nos. , Bearing Housing Left For Rc Feeder Model: Cs2036gt1630407 , Bearing Housing Right For Rc Feeder Model: Cs2036gt1630607 , Screw Stem For Belt Tightening, Moc- Ss-316 , Idler Roller For Rc Feeder Model:Cs2036, 1 Set=12 Nos. , Bushing For Rc Feeder And Coal Millgt1651807 , Bearing Housing Assembly & Rode Housing Assembly For Rc Feeder And Coal Millgt1632107 , Seals Of Hot Shut Off Gate- L2000 Mm, Width 115Mm, Thickness-1.5Mm, Moc-Ss-304 , Seals Of Hot Shut Off Gate-L1800mm, Width 115Mm, Thickness-1.5Mm, Moc-Ss-304 , Center Feed Pipe With Cone For Coal Mill , Dresser Coupling For Center Feed Pipe Of Coal Mill , Roller Liner Device For Coal Mill , Ventury Vane For Coal Mill, Hardness= 60-62 Hrc , Hard Thickness=15Mm , Flow Measure Device For Pa Hot Air Duct Of Coal Mills , Journal Housing Seal Cover For Journal Assembly Of Coal Mills Moc:Is1020 Cast Steel/En24 , Seal Wear Of Coal Mill Journal Assembly Shaft Od: 470Mm, Id: 390Mm, Width: 102Mm, (Moc- Carbon Steel En-24 Hardness- 55-60 Hrc) , Tie Bolt With Nut And Bush Of Coal Mill , Lower Skirt For Coal Mill Hp-1103 (Moc: Carbon Steel) 1 Set= 4 Nos. , Take Up Pulley For Rc Feeder Model: Cs2024, Cs2036gt1650307 , Coal Mill Side Liner (Bottom), Moc: Ms Size:1Mtrx 1Mtr, Thickness:10Mm (1 Set=03 Nos.) , Coupling For Cleanout Conveyor For Rc Feeder , Locking Plate Of Grinding Rolls L=274Mm, T=32Mm , Journal Assembly Top Cover Plate For Coal Mill , Journal Bearing Keeper Moc: En24 Forged, Od-456Mm, Id-105Mm, Pcd-232 Mm, 8 Nos. Of Holes Of Size M32, Thickness-40Mm , Tension Roller For Rc Feeder And Coal Millgt1653407 , Weighing Roller For Rc Feeder And Coal Millgt1631107 , Mill Discharge Valve (Mdv) Size-28 Without Power Cylinder For Coal Mills Hp-1103 , Metallic Expansion Bellow For Pf Piping, Specification: 2 Nos. Congulations,(Ss 304, Thickness Of Congulation-2Mm, Thickness Of Inner Sleeve-5 Mm), Medium: Coal+ Hot Air. Maximum Air Flow Per Mill:125 Tonne Per Hour. Pipe Od-710Mm, Thickness Of Connection End-16Mm (Mild Steel). Position Of Fitment: Vertical. , Expansion Bellow For Pulverized Fuel Piping Specification: 04 Congulations (Ss 304, Thickness Of Congulation-2Mm, Thickness Of Inner Sleeve-5 Mm). Medium: Coal+ Hot Air. Maximum Air Flow Per Mill:125 Tonne Per Hour. Pipe Od-710Mm, Thickness Of Connection End-16Mm (Mild Steel). Position Of Fitment: Horizontal. , Ms Plate For Hot Shut Off Gate L-2000 Mm, Thickness- 3 Mm , Ms Plate For Hot Shut Off Gate L-1800 Mm, Thickness- 3 Mm , Wear Resistant Weld Overlay Plate With Carbide Layer Of 6 Mm For Coal Mills, Carbide Layer Of Inner Side Of Curved Portion Dimension: Height-1500 Mm, Width- 1000 Mm, Thickness- 10 Mm (1 Set= 06 No.) , Ms Flange For Hot Air Diaphragm Moc- Mild Steel , Thickness- 10 Mm, Id- 805 Mm, Od- 944 Mm, Pcd- 890 Mm, No. Of Holes- 20 Nos. Of Size- M18 , Ventury Outlet For Coal Mill Hp-1103 , Moc- Carbon Steel , Ventury Outlet Collar For Coal Mill Hp-1103 , Moc- Carbon Steel
