|
| 1 | Note- The Contractor shall quote his/ their rates without GST. GST will be paid extra by the Department as per prevailing rate at the time of payment. |
| 2 | cq>k.kh rFkk ckck dh dqfV;k uked LFkku ij 2 ua0 \"kkSpky;ksa dk fuekZ.k dk;ZA |
| 3 | Excavation in foundation for retaining & brest walls in all types of soils and rocks including lead, lift and disposal of surplus material as per direction of engineer - in -charge Ordinary rock (not requiring blasting) Upto 3 m depth |
| 4 | Earth work in rough excavation, banking excavated earth in layers not exceeding 20 cm in depth, breaking clods watering, rolling each layer with ½ tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and lift upto 1.5 m in all Kinds of soil. |
| 5 | Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 6 | Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work.(Based on PWD specifications) |
| 7 | Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 Fornominal mix 1:1.5:3 (Hand mixed) |
| 8 | Supplying, fitting, and placing TMT bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202. |
| 9 | Coursed rubble masonry (first sort) with hard stone in foundation and plinth with Cement mortar 1:3 (1 cement: 6 coarse sand) |
| 10 | Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 11 | 12 mm cement plaster on rough side of single or half brick wall of mix 1:6 (1 cement: 6 coarse sand) |
| 12 | 15 mm cement plaster on rough side of single or half brick wall of mix 1:6 (1 cement: 6 coarse sand) |
| 13 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work two coats over and including priming coat with cement primer |
| 14 | Finishing walls with textured exterior paint of required shade-Two or more coats appiled @ 3.28 ltr /10 sqm over and including base coat of water profing cement paint applied @ 2.20 /10sqm |
| 15 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 16 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(80x50x6mm) |
| 17 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required0.80mm thick with zinc coating not less than 275gm/m (Excluding Supply of C.G.S Sheet) |
| 18 | Providing ridges or hips of width 60 cm over all width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. 0.80mm thick with zinc coating not less than 275gm/m |
| 19 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 20 | Painting onG.S.sheetwith synthetic enamelpaintofapprovedand manufacture of required colour to give an even shade : (one or more coats) |
| 21 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture. |
| 22 | Making and cutting of G.S. sheet high impact Polypropylene 6mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts dia as per drawing . G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete excluding the cost of purlins, rafters and trusses: corrugated sheets and including cutting to size and shape wherever required. |
| 23 | Providing and fixing pressed steel door frames confirming to IS: 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together bymechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge. |
| 24 | Providing & laying polished antiskid ceramic floor tiles in different size with Ist quality conforming to IS : 15622 of approved make in all colours and shade aproved by engineer-in-charge/architect , laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) including grouting the joint with white cement andmathching pigment etc. Size of tile (300x300 ) |
| 25 | Providing and fixing M.S. grills of required pattern in frames |
| 26 | Providing and fixing 30mm thick wiregauge for ventiletter fly proof galvanised M.S. wire gage with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm. |
| 27 | Providing and fixing bright finished brass 100 mm `mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 28 | Providing and fixing bright finished brass towerbolts (barrel type)with necessary |
| 29 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 115622 (thickness to be specified by the manufacturer) of approved make like NITCO, ORIENT, SOMANY KAJARIA, or equivalent in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointinginwhitecementmixedwithpigmentofmatchingshade complete. |
| 30 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm White Vitreous china Orissa pattern W.C. pan of size each580x440mm with integral typefoot rests. |
| 31 | White Vitreous China Wash basin size 630x450 mm each with a pair of 15 mm C.P. brass pillar taps. |
| 32 | Providing and fixing toilet paper holder : |
| 33 | Providing and fixing PTMT soap Dish Holder havinglength of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms. |
| 34 | Providing and fixing brass bib cock of approved quality |
| 35 | Providing and fixing unplastisised P.V.C. connection pipe with PTMT Nuts of approved quality and colour. |
| 36 | Providing and fixing trap of self cleansing design with screwed down or hinged |
| 37 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 38 | Concealed pipe with anti corrosive bitumastic paint, cutting chases and making good the wall |
| 39 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.32 mm |
| 40 | Providing and fixing unplasticised Rigid PVC pipes for drainage |
| 41 | Constructing masonry Chamber 120x120x100 cm, inside with 75 class designation brick work in cement mortar 1:4( cement :4 coarse) for sluice valve, with C.I. surface box 100 mm. top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10(1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design : |
| 42 | }kyh ls thjks IokbUV ds e/; iSny ekxZ ds ejEer ,oa lq/kkjhdj.k dk dk;ZA |
| 43 | Excavation in foundation for retaining, breast walls etc, in all types of soils and rocks including all lead, lift and disposal of surplus material as per direction of engineer - in - charge, as per drawing and technical specifications Clause 305.1 of MORD Specifiction |
| 44 | Random Rubble Masonary laid dry in breast wall,retaining wall, parapets,scupper etc. Including supply of all materials,labour,t & p& royality etc, required for proper complition of work.(As per PWD)( Uttarakhand specifications) |
| 45 | Providing and laying of wire crates 3.00x1.50x1.50 in size with GI wireconforming to IS: 280 & IS:4826 in 150mm x 150mm mesh laid with stoneboulders. as per direction of Engineer-in- charge. (As per PWDUttarakhand specifications)GI wire 10 gauge BWG |
| 46 | Hand Packed stone filling in back of wallls including cost of all materials, royality, T&P etc. complete as per direction of Engineer-in- charge. (As per PWD Uttarakhand specifications) |
| 47 | View Point at Bujhani Km 22.50 (Between Furkiya to Zero point) Location IInd |
| 48 | Excavation in foundation for retaining, breast walls etc, in all types of soils and rocks including all lead, lift and disposal of surplus material as per direction of engineer - in - charge, as per drawing and technical specifications Clause 305.1 of MORD Specifiction |
| 49 | Random Rubble Masonary laid dry in breast wall,retaining wall, parapets,scupper etc. Including supply of all materials,labour,t & p& royality etc, required for proper complition of work.(As per PWD)( Uttarakhand specifications) |
| 50 | Hand Packed stone filling in back of wallls including cost of all materials, royality, T&P etc. complete as per direction of Engineer-in- charge. (As per PWD Uttarakhand specifications) |
| 51 | Supplyingand Fixing of 1.80m long BenchesGrouting in 1:1.5:3 cement Concrete Including Painting with Enamel Paint,Including Supply of all Material Labour T&P et.c complete. |
| 52 | Supply and FixingErecting of M.S.steel Railing on Medium Weight 40x40x3mm sq.tube as per drawing steel pipe railing duly painted on medium weight 40x40x3mmsq.tube 1.0m high above ground 2 m centre to centre complete as per approved drawing including car |
