|
| 1 | Proper Installation & commissioning in New PMCC Room using adequate size foundation bolts in guidence of L&T including fixing of Bus Bars Fish Plates, control circuit interconnections in between verticles etc. of L&T make PMCC Panel, 415 V, 50 KA for 1 Sec, IP-54, 2mm thick, powder coated, double front type with 2 Nos. Incomer and 1 no. bus-coupler feeder comprising drawout ACB with Electrical& Manual closing, having Undervoltage relay, Overcurrent & Short circuit protection, Earth Fault relay, Shunt trip coil & Auxillary contacts (2NO+2NC) for necessary interface, one from transformer secondary and one from DG Set (Change over Panel) with Interlock facility and outgoing drawout motor as well as power feeders for various new loads includingpumps/motors & Lighting facility etc. complete with all accessories, auxiliariesetc complete in all respects as specified in technical specification, data sheet & SLD no. C396-E-SLD-101B, Rev-0 under guidance of L&T.(Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 2 | Proper Installation & commissioning in New PMCC Room using adequate size foundation bolts in guidence of L&T including fixing of Bus Bars Fish Plates, control circuit interconnections in between verticles etc. of L&T make LDB Panel, 415 V, 10 KA for 1 Sec, IP-54, 2 mm thick, powder coated, single/double front type with two incomers of 400 A, 4-pole MCCB each with Overcurrent, Short circuit & Earth Fault protection, Shunt trip coil & Auxillary contacts (2NO+2NC) for necessary interface and outgoing non drawout Fuse-switch dis-connectors for Lighting of new facilities and emergency loads of the plants (covered under the augmentation plan) complete with all accessories, auxiliariesetc complete in all respects as specified in technical specification, data sheet & SLD no. C396-E-SLD-101C, Rev-0. (Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 3 | Proper Installation with all necessary hardwares in New PMCC Room using adequate size foundation bolts in guidence of L&T including fixing of Bus Bars Fish Plates, control circuit interconnections in between verticles etc. of L&T make APFC Panel 415 V,TPN, IP-54, 375 KVAR, 2mm thick, powder coated, with detuned filter consisting of 2x100kVAr + 2x50kVAr + 2x25kVAr + 1x15kVAr + 1x10kVAr (Total KVAr Rating = 375 KVAr) in step with automatic correction of Power Factorto maintain the terminal power factor of 0.95 and each step with contactor based step control as necessary. Incomer shall be draw-out type ACB (Min 630A) with single front type indoorwith operating mechanism, all accessories, auxiliariesetc. complete in all respects as specified in technical specification, data sheet & SLD no. C396-E-SLD-101D, Rev-0 & commissioning. (Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 4 | Installation & commissioning of 110V D.C.75AH Ni-Cd Battery for 1 Hr. battery back-up, along with associated Float and Float-cum-Boost Charger Panel with protections & indications, DCDB with 125A DP Incomer and nine (9) nos. 32A DP switch fuse unitsand standard accessorie as perenclosed technical specification and Drg. no.C396-E-SLD-101F, Rev-0. along with all necessary strcturals, hardware etc. and as per direction of site engineer. (Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 5 | Installation of Flame Proof Push Button Station including structurals , harwares & grouting on floor/coloumns/walls for control of motors for lighting supply, Aluminium LM6, IP65, Stainless Steel with indicating lamp for ON/TRIP with ON/Emergency Stop Push butttons with padlocking arrangement with spare aux. contact (1NO+1NC) for control interface with associated Structural support/mounting arrangement. (Suitable for Zone-1, IIC and T3, Make: Baliga /FCG Flameproof Control Gears/FlexproAs per direction of Site Engineer. |
| 6 | Installation as above but with indicating lamp for FORWARD/REVERSE/TRIP and with FORWARD/REVERSE/Emergency Stop Push butttons.As per direction of Site Engineer. |
| 7 | Installation of Flameproof MCBDB 240 V, 10 KA for 1 Sec, FLP,IP-65, Aluminium, LM6, with 32 A DP RCCB as incomer, and 9 Nos. of 10A DP MCBwith indication lamps with all accessoriesincluding structurals , harwares & grouting on floor/coloumns/walls suitable for wall mounting for emergency lighting or small power distribution(Suitable for Zone-1, IIC and T3, Make: Baliga /FCG Flameproof Control Gears/Flexpro) . As per direction of Site Engineer.(Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 8 | Installation of Flameproof Phase Splitter Board (Junction Box) FLP,IP-65, Aluminium, LM6, with terminals and cable entries suitable for 1-run, 3.5-core 35 mm2 cable as incomer (TPN) and twelve (12) nos. 3-core cable 2.5 mm2 cable as outgoing (SPN) for lighting, with all accessories including structurals , harwares & grouting on floor/coloumns/walls (Suitable for Zone-1, IIC and T3, Make: Baliga /FCG Flameproof Control Gears/Flexpro) . As per direction of Site Engineer.(Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 9 | Installation of Flameproof 415V, 63A three phase plug and socket meant for welding receptacle / any other three phase auxiliary loads shall be provided with 5 pins (3P + N + E), and TPN heavy duty switch, complete with all accessories suitable for column mounting (Suitable for Zone-1, IIC and T3, Make: Baliga /FCG Flameproof Control Gears/Flexpro) .(Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 10 | Installation of Flameproof 240V, 16A single phase plug and socket meant for convenience receptacle / any other single phase auxiliary loads shall be provided with 3 pins (P + N + E), and SPN heavy duty switch, complete with all accessories suitable for column mounting (Suitable for Zone-1, IIC and T3, Make: Baliga /FCG Flameproof Control Gears/Flexpro) .(Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 11 | Supply & Fixing of Plugs for flameproof equipment1/2\" ET plugs for flameproof equipment |
| 12 | Supply & Fixing of Plugs for flameproof equipment1\" ET plugs for flameproof equipment |
| 13 | INDOOR LIGHTINGFor License AreaInstallation of FLP lighting fixtures complete with mounting bracket/arrangement, flame proof, Wire Guard, Control Gear Box as per the type of fixture, lamps, interconnecting cables with terminals for 2 Nos incoming & Outgoing, FLP DC glands, lugs etc. including pipe inserts for cables and connecting work as per specifications, drawings and instruction of Engineer-in-charge.Work to be completed in all respects. |
| 14 | Installation of Flame proof Well Glass type fixture, Aluminium, LM6, with 36W LED lamp andintegral LED Driver for New LPG Bottling Sheds with all necessary structural as may be required (Suitable for Zone-1, IIC and T3,Make: Baliga /FCG Flameproof Control Gears/Flexpro) (Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 15 | Installation of Flame proof Well Glass type fixture, Aluminium, LM6, with 50W LED lamp integral LED Driver for New LPG Bottling Shedswith all necessary structural as may be required(Suitable for Zone-1, IIC and T3, Make: Baliga /FCG Flameproof Control Gears/Flexpro) (Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 16 | Supply & Installation of Flame proof non integral floodlight fittings, Aluminium, LM6, suitable for 250W LED for peripheral lighting of New LPG Bottling Shedswith all necessary structural as may be required (Suitable for Zone-1, IIC and T3, Make: Baliga /Stahl/Flexpro) (Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 17 | INDOOR LIGHTINGFor Safe AreasSupply & Installation of industrial type lighting fixtures and socket outlets complete with mounting rods, brackets, hangers, lamps, controlgear as required, circular JB, interconnecting wire & flexible conduit for interconnection from JB to fixture etc. |
| 18 | Industrial type, heavy duty socket outlet - 415V, 63A, TPN+E with built-in MCCB/Isolator, of approved make and type. |
| 19 | Industrial type, heavy duty socket outlet - 240V, 16A, SPN+E with built-in MCB/switch, of approved make and type. |
| 20 | Installation ofwith necessary structurals, foundations etc. of FLP (Flame Proof) Out door Type Field Call Stations, Aluminium LM6, IP65, Stainless Steel, complete with all accessories, suitable for wall/column mounting. This shall beused for internal communication between plant personnel compatible with any type of existing EAPBX System, including supply of suitable communication cable and other acceessories, as required.(Suit able for Zone-1, IIC and T3, Baliga make or equivalent from approved vendor list) (Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 21 | Installation of Supplied weatherproof/flameproof type fuse distribution boards, each housing one (1) no. 63A TPN isolator with twelve (12) nos. of 10A SPN fuses (with neutral link)with all necessary structural as may be required for connection up to individual flood light fittings, complete with all accessories, FLP D/C cable glands etc. as required.. |
| 22 | Power and Control Cables & AccessoriesDesign, manufacture, shop testing, supply includingpacking and forwarding, transportation, delivery at site, storage, transportation from storage to site of Power and Control Cables & Accessories of following types and sizes :(Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item )11KV (UE) Grade - Type : A2XFY |
| 23 | Supply of 11kV (UE) A2FY 3 Core Cable |
| 24 | Laying of 11kV(UE) 3-core 240 sq. mm. |
| 25 | Heat shrinkable / push ON cable termination kit of RAYCHEM / MAHINDRA / CCI make for above - indoor type |
| 26 | Heat shrinkable / push ON cable termination kit of RAYCHEM / MAHINDRA / CCI make for above - outdoor type |
| 27 | ARMOURED CABLES Supply & laying ofXLPE insulated PVC sheathed aluminium/copper conductor, 1.1 kV grade armoured cable conforming to IS:7098, as per approved make in ground/ trench/surface/pipe, etc. whereever required as per direction of Engineer In-charge. Note: The rate of Installation should be inclusive of Cable clamps, tags Saddles, Consumables etc. Trays/pipes, trenches, fabricated tray supports etc will be covered & paid in Separate Items. |
| 28 | 4-core 6 sq. mm.Stranded Copper Armoured FRLS Cable |
| 29 | 3 Core x 2.5 sq. mm Stranded Copper Cable FRLS |
| 30 | 4 Core x 2.5 sq. mm Stranded Copper Cable FRLS |
| 31 | 6 Core x 2.5 sq. mm StrandedCopper Cable FRLS |
| 32 | 3.5 Core x 95Sq. mm AluminiumCable FRLS |
| 33 | 3.5 Core x 120Sq. mm AluminiumCable FRLS |
| 34 | Laying of 1100V Grade - Type : A2XFY/A2XWY IOC supplied cables |
| 35 | 3.5-core 240 sq. mm. |
| 36 | 3.5-core 185 sq. mm. |
| 37 | 3-core 120 sq. mm. |
| 38 | 3.5-core 95 sq. mm. |
| 39 | 3.5-core 35 sq. mm. |
| 40 | 4-core 16 sq. mm. |
| 41 | 3-core 16 sq. mm. |
| 42 | Laying of 1100V Grade - Type : 2XFY/2XWY IOC supplied cables |
| 43 | 3-core 2.5 sq. mm. |
| 44 | 4-core 2.5 sq. mm. |
| 45 | 5-core 2.5 sq. mm. |
| 46 | 7-core 2.5 sq. mm. |
| 47 | 12-core 2.5 sq. mm. |
| 48 | 4-core 6 sq. mm. |
| 49 | 2-core 10 sq. mm. |
| 50 | CABLE TERMINATION GLANDS NON-FLP HEAVY DUTY DOUBLE COMPRESSION Cable Termination (NON FLP): Providing termination of 1.1 kV grade armoured cable for the following sizes including supply of NON FLP heavy duty Double Compressioncable glands, crimping type lugs and allied jointing materials, etc. all complete as per specificationand direction of Engineer In-charge. Glands and lugs shall be of approved make. Copper lugs for copper cables and aluminium lugs for aluminium cables shall be used. |
| 51 | Suitable for 1100V Grade cables, Type : A2XFY/A2XWY/2XWY/2XFY |
| 52 | 3.5-core 240 sq. mm. |
| 53 | 3.5-core 185 sq. mm. |
| 54 | 3-core 120 sq. mm. |
| 55 | 3.5-core 95 sq. mm. |
| 56 | 3.5-core 35 sq. mm. |
| 57 | 4-core 16 sq. mm. |
| 58 | 3-core 16 sq. mm. |
| 59 | Suitable for 1100V Grade cables, Type : 2XFY/2XWY |
| 60 | 3-core 2.5 sq. mm. |
| 61 | 4-core 2.5 sq. mm. |
| 62 | 5-core 2.5 sq. mm. |
| 63 | 7-core 2.5 sq. mm. |
| 64 | 12-core 2.5 sq. mm. |
| 65 | 4-core 6 sq. mm. |
| 66 | 2-core 10 sq. mm. |
| 67 | FLP HEAVY DUTY DOUBLE COMPRESSION Cable Termination(FLP):Providing termination of 1.1 kV grade armoured cable for the following sizes including supply of FLP heavy duty double compression cable glands, Baliga/CEAG-FCG /Flexpro/ FEPL make, crimping lugs and allied jointing materials, etc. all complete as per specification & direction of Engineer In-charge. Copper lugs for copper cables and aluminium lugs for aluminium cables shall be used. |
| 68 | 3-core 120 sq. mm. |
| 69 | 3.5-core 95 sq. mm. |
| 70 | 3.5-core 35 sq. mm. |
| 71 | 4-core 16 sq. mm. |
| 72 | 3-core 16 sq. mm. |
| 73 | Suitable for 1100V Grade cables, Type : 2XFY/2XWY |
| 74 | 3-core 2.5 sq. mm. |
| 75 | 4-core 2.5 sq. mm. |
| 76 | 5-core 2.5 sq. mm. |
| 77 | 7-core 2.5 sq. mm. |
| 78 | 12-core 2.5 sq. mm. |
| 79 | 4-core 6 sq. mm. |
| 80 | 2-core 10 sq. mm. |
| 81 | Grid Earth Pits (For Max 1 ohm resistance)- GI Medium duty Pipe Electrode with min 5mm thick chequered plate cover with details as per IS 3043 with associated civil work- 100dia Heavy GI Pipe as per IS 1239 with detail as per enclosed drawing with TS |
| 82 | Earth plates 600X600X6 mm. thk. Gl. Plate, complete with bolts, nuts and washers for equipment earthing connections |
| 83 | Neutral Earth Pits(For Max 1 ohm resistance) - Plate Electrode with min 5mm thick chequered plate cover with details as per IS 3043 with associated civil work- 610x610x3mm. Size copper plate having weight of 9.84 kg and 1 no. 25x5mm copper strip (3.2M long and 1 no. 6 sq. mm. PVC insulated stranded copper wire (4 Mtr. long) and 50mm. dia heavy GI Pipe as per IS 1239 with detail as per specification/approved drawing |
| 84 | Supply & drawing/laying, jointing, connecting, testing and commissioning ofearth strip/copper strip/GI wire for earthing and lightning protection under or aboveground complete as per specification for the following : |
| 85 | Plant grid earth GI strip(50 x 6 mm.) with required standard saddle/support strips etc. |
| 86 | Horizontal/vertical air termination for lightning protection of Shed - GI strip(32 x 6 mm.) with required standard saddle/support strips, fastners etc. |
| 87 | Supply & fixing of Earthing conductor for earthing of equipment (with required lugs/connectors) : |
| 88 | 25 x 6 mm. GI strip |
| 89 | 150 sq mm PVC covered Al. cond. |
| 90 | 25 sq mm PVC covered Al. cond. |
| 91 | 16 sq mm PVC covered Al. cond. |
| 92 | 6 sq mm PVC covered Al. cond. |
| 93 | 2.5 sqmm PVC covered Cu Cond. |
| 94 | 16 SWG GI Wire (Twisted pair) |
| 95 | Point Wiring Indoor Lighting Supply of point wiring materials for LT Panel Room or new HV Switchgear Room, as per details in construction drawing & specification, suitable for concealed wiring or thru\" PVC casing and caping method (including supply of materials with cleats on surface) - for luminaries, sockets, lamps, industrial type heavy duty exhaust fans, ceiling fans with down rod / connector, electronic speed regulator, junction box, switch boxes & switches (ANCHOR ROMA make or equivalent) with Multi strand Flexible FRLS PVC insulated copper conductor wires/cables of suitable size (2.5/4.0/6.0sq.mm) with earthing wires (1.5/2.5sq.mm), as required to suit site condition etc. as mentioned below:(Note: Please also refer technical specification and drawing for all required items /components/works for this SOR item ) |
| 96 | Light, fan points (avg. length : 16M). |
| 97 | Power point for socket outlet (avg. length : 25M) |
| 98 | Cable dressing and tagging of cables in installed Main Electrical Panel and Distribution Boardsin PMCC Room. The work includes disconnection of all cables from panel side, removing all cabes upto entry to the panel room, relaying the cables through cable tray, or cable trench or electrical conduit and termination of cables with proper size cable glands in panel side after tagging with cable tags for identification. Payment for cable tray, conduit, any civil works, cable glands to be paid seperately. |
| 99 | Standard Electrical Shock hazard charts complete with frame and glass |
| 100 | Metal First Aid Box/Medical Kit Box with Handle | Multi Shelves | Wall Mount | For House, Educational Institutes, Commercial Spaces |
| 101 | Carbon-di-oxide(CO2) type fire extinguisher 4.5 Kg capacity Complete with gunmetal valve conforming to IS : 3224 With ISI mark , Discharge horn with bend & wall fixing Bracket, stand etcWith Mfg. Test certificate. |
| 102 | Fire buckets with round bottom duly filled with fine river sand, supplied with mounting stand (Fire Stone Fire Bucket Stand with 4 nos Bucket) |
| 103 | Caution boards including supply of necessary clamps, bolts and other hardware. |
| 104 | Insulating MatsSupplyofInsulating Mats (as per IS:15652 - 2006) of 1000mm width, required for maintenance of electrical equipment in substation as required including cutting to required shape in running length and including all labour and materials etc. complete and as per directions of Engineer-In-Charge as per applicable Indian or International standards and Indian Electricity Rules. |
| 105 | 11 KV grade of 3 mm thick |
| 106 | 415V grade |
| 107 | Supplying, fabricating and installing following sizes of perforated GI cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling and/or fix to steel/RCC columns, beams or any other structure members with MS suspenders, angles, channels, etc complete as per the direction of IndianOil |
| 108 | 50mm wide x 50 mm(2mm. Thick) |
| 109 | 100mm wide x 50 mm (2mm. Thick) |
| 110 | 150mm wide x 50mm (2mm. Thick) |
| 111 | GI Pipes: Supply & laying of pipes of following types and sizes (incl. bends):- |
| 112 | 50 mm NB (Class B GI, as per IS 1239 : Part-1) |
| 113 | 80 mm NB (Class B GI, as per IS 1239 : Part-1) |
| 114 | 100 mm NB (Class B GI, as per IS 1239 : Part-1) |
| 115 | Supply & filling of fine River Sand for cable trenches |
| 116 | Providing and laying dry brick on edge flooring in required pattern with bricks of Class designation 7.5 on a bed of 12 mm mud mortar including filling joints with river sand with common burnt clay non- modular bricks |
| 117 | Providing and laying Brick work with common burnt clay F.P.S (non Modular) bricks of class designation 7.5 in foundation & plinthi) Brick work in Cement mortar 1:4 (1 cement : 4 coarse sand)IN FOUNDATION AND PLINTH |
| 118 | PCC 1:2:4(1 Cement : 2 Coarse Sand :4 Graded stone aggregate of 20mm) |
| 119 | Structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 120 | Supplying and installing of GI cable route marker with 100mm x 100mm x5mm thick GI Plate with inscription thereon, bolted/welded to 35mm x 35mm x 6mm angle iron, 600mm long and fixing the same in ground as per drawing & direction of Indian Oil Job includes painting with one coat of red oxide & finishing paint |
| 121 | Industrial Step Ladder: Supply of 8 feet industrial step ladder with platform and rubberised four legs, self-supporting. All the materials used shall be suitable for use in hazardous areas. |
