Numaligarh Refinery Limited has published Tender For Construction Of Kitchen Cum Lunch Area (Near Peb) And Other Misc. Civil And Mep Works At The Nrl Centre Guwahati. Submission Date for this Tender is 17-10-2023. PEB Tenders in numaligarh Assam. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 03-Oct-2023 | Corrigendum 1- Pre-bid meeting details | Other | 10-10-2023 |
| 2 | 10-Oct-2023 | Corrigendum 1- Date extension | Date | 17-10-2023 |
| Sl. No. | Item Description |
| 1 | Civil Works |
| 2 | Earth work in excavation in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil. All Kinds of soil. |
| 3 | Earth/Sand filling in plinth in layers not more than 150 mm thk. Including necessary carraige, watering, ramming etc complete as directed and specified including payment of land compensation, forest royality, sales tax and other duties and taxes as may be necessary a) with earth or silt or sand obtained by head load with lead upto 90 m and lift upto 2m |
| 4 | Earth/Sand filling in plinth in layers not more than 150 mm thk. Including necessary carraige, watering, ramming etc complete as directed and specified including payment of land compensation, forest royality, sales tax and other duties and taxes as may be necessary c) With river sand or silt (Predominantly non plastic) by truck carraige including loading and unloading |
| 5 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand) (UPTO PLINTH LVL) |
| 6 | P/C 115mm thick Brick Work Providing and constructing half brick (115mm thick) masonry with locally available approved quality Fly ash bricks having minimum crushing strength 35 Kg/Sq. cm and maximum water absorption 20%, in cement mortar CM 1:4 (1 cement : 4 Sand) mixed with approved non-shrinking compound as per manufacturers instruction in specified courses of approved bond and including providing RCC patli beam of 115mm x 100 mm at every 1.00m c/c with 2 nos. 8 mm dia Tor bars and 6 mm dia links at 300 c/c in cement concrete of mix M 20, required formwork complete with raking out joints, curing, doing independent double legged scaffolding as per specifications etc. at heights and leads all as directed by PM to his entire satisfaction. (Patli beam is part of the item) |
| 7 | Providing and constructing 230mm or more thick masonry with locally available approved quality Fly ash bricks having minimum crushing strength 35 Kg/Sq. cm and water absorption maximum 20% in cement mortar CM 1:6 (1 cement : 6 Sand) mixed with approved non-shrinking compound as per manufacturer#s instruction in specified courses of approved bond and including raking out joints, curing, doing independent double legged scaffolding, all complete as per specifications etc. at all heights, depths and leads all as directed by PM to his entire satisfaction. |
| 8 | Providing and applying 12mm thick plaster in cement mortar mix ratio CM 1:4 (1 cement : 4 sand) mixed with polypropylene fibers as per instruction of the approved manufacturer, to internal surfaces of concrete and masonry work; including raking out joints, hacking concrete surfaces and applying approved chemical bonding agent and applying a scratch coat over concrete surfaces by bonding / adhesive chemical coat as directed by approved manufacturer to create a key, cleaning / grooving deep junctions of concrete & masonry, grouting then back by mortar mixed with non shrinking compound along with packing of clean, fresh square cut aggregate; also providing and fixing 20 gauge GI chicken mesh @ 150 mm wide to junctions of concrete and masonry, preparing jambs, sills, grooves, pattas, wattas, rounding of corners, any circular works, ramps etc. all complete as per architectural drawings, specifications and finished smooth with wooden rundha etc. or as specified by the PM at all leads, depth and lifts, doing independent double-legged scaffolding, cleaning of surfaces, curing, etc. complete as per specification and to the approval of the PM. |
| 9 | Providing, preparing and plastering readymade proprietary Gypsum plaster to internal walls and ceilings average 13mm thick using Gyproc (universal) Elite plaster, wall surfaces of concrete, masonry work, including plaster mesh reinforcement of approved make and quality wherever required at junctions of masnory and concrete, doing jambs, sills, all types of groovesas shownin the drawing, wattas, rounding of corners etc. all complete as per architectural drawing, specification and directed by PM, at all lift, lead and depth, doing independent double legged scaffolding, making gypsum plaster mix as per approved manufacturer#s instruction, applying high grade polymer based bonding agent (Gyproc Bond IT) mixed with approved quality sand on RCC surfaces etc. complete as per manufacturer"s specifications and approved by PM. Plastering shall be to correct line, levels and plumb including curing, cleaning etc. complete to entire satisfaction of PM. |
| 10 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 11 | Providing and applying Emulsion paint of approved make and colour conforming to IS in two coats (surface and finish acceptable to the PM must be achieved by the contractor and any additional coats if required shall be at the cost of the contractor); including preparing surfaces, filling up with gypsum or approved crack filler, binder; cleaning and making the surface dustfree, applying a sealer or primer coat of paint as recommended by approved paint manufacturer, applying two coats of paint (of approved make and shade), required scaffolding, cleaning and protecting till the handing over of site to the employer all complete to entire satisfaction of the PM. |
| 12 | Providing, machine mixing (volumetric) and laying plain cement concrete (PCC) for levelling course etc.; including compacting, curing, required centering & shuttering and its removal, dewatering where required, cleaning, preparing surfaces, junctions, etc.; complete at all depths and leads as per the drawing and to entire satisfaction of the PM. 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). All work above plinth upto 6th floor. |
| 13 | Providing, machine mixing (volumetric) and laying plain cement concrete (PCC) for levelling course etc.; including compacting, curing, required centering & shuttering and its removal, dewatering where required, cleaning, preparing surfaces, junctions, etc.; complete at all depths and leads as per the drawing and to entire satisfaction of the PM. 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). All work below plinth. |
| 14 | Providing andlayingdamp-proof course 40mmthick with cement concrete 1:2:4(1 cement : 2 coarse sand (zone -III): 4 graded stone aggregate 12.5 mm nominal size) |
| 15 | Applying a coat of residual petroleum bitumen of penetration VG 10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 16 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. |
| 17 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor 6thh level, but excluding the cost of centering and shuttering, reinforcement. Grade: 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). All above plinth. |
| 18 | Centering and shuttering including strutting, propping etc. andremoval of form for Foundations,footings,bases of columnsincluding beams etc. for mass concrete |
| 19 | Centering and shuttering including strutting, propping etc. andremoval of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 20 | Centering and shuttering including strutting, propping etc. andremoval of form forColumns, pillars, piers, abutments, posts and struts |
| 21 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level for Thermo-Mechanically Treated bars of grade Fe-500 D or more. |
| 22 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 RMs lead as per direction of Engineer-in-charge. In cement mortar |
| 23 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 RMs lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 24 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 RMs lead. |
| 25 | Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. |
| 26 | Laying old cement cocrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineerin-charge. (Old CC paver blocks shall be supplied by the department free of cost). |
| 27 | Taking out existing kerb stones of all types from footpath/ central verge, including removal of mortar etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. |
| 28 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 20 km for all lifts, complete as per directions of Engineer-in-charge. |
| 29 | Providing and laying 6" average brick bat coba with approved water proofing compound mixed; laid to proper slope, curing, etc., complete. All water proofing to have 10 years guarantee. Rates are inclusive of shifting of materials upto 6th floor. |
| 30 | Providing and applying waterproofing compoun"Providing and applying Waterproofing in toilets upto height of 3"-0", with approved water proofing compound, with 10 years guarantee. All complete as per Architect"s instructions and specifications.All complete as per EIC"s instructions and specifications. |
| 31 | Concreting of the structure with free flow nonshrink cementitious microconcrete with Renderoc RG of Fosroc or equivalent after proper mixing with cleanwater including formwork followed by proper curing for 28 days as per manufacturer"s specifications complete and as directed by the Department |
| 32 | Providing and Injecting a two-part liquid Polyurethane ArmGrout Inject PU1/PU4 when mixed in the proportions supplied it reacts rapidly with water to form a foam barrier using a suitable grout pump after drilling for installation of packers, sealing the crack with some epoxy adhesive as per manufacturer instruction or as directed by the engineer in charge. After injection the packer need to be removed and seal the same with some epoxy mortar. Cost inclusive of drilling, injecting, packers and whatever adhesive required for injection. |
| 33 | Providing & fixing 16mm dia MS nozzles in a grid of 1m c/c up to the half of the thickness of the concrete structure.A grout slurry of neat cement & chloride free expanding grout Cebex 100 of Fosroc Chemicals or Mastergrout CPG-1 of Choksey Chemicals or MasterFlow 150 of BASF or equivalent @ 0.5% by weight of cement water cement ratio 0.35 to 0.40 and viscosity not more than 1.02 centipoise with grouting pressure till the refusal of injection grout . The grouting operation pressure shall be 2Kg/sq.cm.Cutting the exposed nozzle after the grouting with a good cutter to make the surface free from the grouting pipes and to seal the gap with plugging compound Masterplug of Choksey Chemicals as per the specification and the direction of the department complete including formwork. |
| 34 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical/manual including loading, transporting, unloading from 6th floor of the buildingto approved dumping yard at site at Ground floor/ municipal dumping ground for lead upto 1 km for all lifts, complete as per directions of Engineer-in-charge. |
| 35 | Flooring Works |
| 36 | Providing, machine mixing and laying 85mm thick cement concrete screed in mix ratio 1:2:4 (1 cement : 2 coarse sand : 4 aggregates 12.5mm size), laid in panels, well vibrated, compacted to correct line and level, surface finished ready to receive floor finish and cured by keeping well covered and protected against excesses of any type (The contractor will provide for preparation of surface by cleaning, hacking and exposing aggregate to achieve the best bond) etc. all complete at all heights and leads to the entire satisfaction of the PM. below Vitrified Tiles Flooring. |
| 37 | Providing and laying approved size, quality, colour, design and shade fully homogeneous Vitrified tile of approved make (conforming to IS 15622) flooring in pattern as detailed in drawing or as directed by the PM. Tile to be bedded in cement sand mortar mix ratio 1:6 (1 cement : 6 sand) including cleaning and preparing the surface for bedding, spreading neat cement slurry by using minimum cement about 2 kg/Sqm over cleaned surface and spreading neat cement paste using minimum cement about 4.5 kg/Sqm over cement mortar bed to be cleaned and grouted with matching colour approved quality readymade grout, curing, cleaning, to required line, level, all complete at all leads, lifts and heights to the entire satisfaction of the PM. VT1 - 600mm x 600mm Vitrified tile Flooring. Make Quotone, Johnson or AGL ,Somany or equivalent. |
| 38 | Providing and fixing approved quality, colour, design and shade fully homogeneous Vitrified tile, and thickness of 6-8mm approx. (confirming to IS 15622) dado to walls/columns, as shown in drawing or as directed by the PM. Tile fixed with approved compatible adhesive (Bal / Laticrete or equivalent approved) over concrete surface. Joints are well cleaned grouted with matching colour approved quality polymer based readymade grout, curing, cleaned and where specified or shown in drawing etc. complete to the entire satisfaction of the PM. 600mm x 300mm Vitrified tile dado (Location : Kitchen &Toilets) (Basic Rate - 80/Sqft) Make Quotone, Johnson or AGL,Somany or equivalent. |
| 39 | Providing and fixing 100mm high skirting made out of same tiles as that of flooring fully homogeneous Vitrified tile of thickness 6-8mm approx. to walls/columns as shown in drawing or as directed by the Architect. Tiles shall be fixed with approved compatible tile adhesive of approved make to correct line, level and plumb. Joints are well cleaned and grouted with matching colour of approved quality with polymer based grouts (Bal / Laticrete or equivalent approved) to match shade of the tile and cured, cleaned and including finishing junction of plaster, protecting etc. all complete at all heights, lifts and leads to the entire satisfaction of the PM. (Basic Rate - 80/Sqft)Make Quotone, Johnson or AGL,Somany or equivalent. |
| 40 | Providing and fixing about machine cut, polished approved Marble stone sills, jambs, soffits etc., in required shape with required grooves, mouldings, chamfering / rounding edges, polishing etc. also include required pins / cram etc. for holding down complete including fixing with approved adhesive over 12mm thick MDF base, including cleaning, polishing etc. complete to the approval of the PM. b) 150mm wide Crema noce and equivalentmarble ledge wall/ Window sill/Door sill. |
| 41 | Providing and laying 16-17mm thick Marble flooring of machine cut, machine polished in pattern and size as detailed in drawing or as directed by the PM. Stone to be bedded in mechanically mixed cement sand mortar mix ratio 1:6 (1 white cement : 6 sand) overall about 25mm thick including cleaning and preparing the surface for bedding, spreading neat cement slurry by using minimum cement about 2 kg/sqm prior to bedding and spreading white cement paste using minimum cement about 4.5 kg/sqm over bedding, joints to be cleaned and grouted with matching colour approved quality polymer based readymade compatible grout, curing, cleaning, polishing,protecting with HDP sheet / POP till handing over etc. to required line, level, etc. all complete at all heights and leads to the entire satisfaction of the PM. Marble - Crema Noce Marble Flooring.(Basic Rate - 450/Sqft for Crema Noce) |
| 42 | Providing and laying 20mm thick machine cut, machine / mirror polished approved Kota stone flooring in pattern and size as detailed in drawing or as directed by the PM. Stone to be bedded in cement sand mortar mix ratio 1:6 (1 cement : 6 sand) minimum 20 mm thick including cleaning and preparing the surface for bedding,spreading neat cement slurry by using minimum cement about 2 kg/sqm prior to bedding and spreading cement paste using minimum cement about 4.5 kg/sqm over bedding, joints to be cleaned and grouted with matching colour approved qualityreadymade polymer based grout, curing, cleaning, polishing, protecting till handing over by POP covering, etc. to required line, level, etc. all complete at all heights and leads to the entire satisfaction of the PM. |
| 43 | Providing and fixing about 100mm high approved 20mm thick machine polished approved Kota stone skirting, machine cut as detailed in drawing. Stone fixed by approved compatible adhesive on back to correct line, level and plumb. Joints are well cleaned grouted with matching colour readymade approved quality polymer based grout, curing, cleaned and where specified or shown in drawing exposed edge of stone rounded / chamfered and polished etc. complete to the entire satisfaction of the PM. |
| 44 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. (Basic rate : Rs. 290 sq.ft) |
| 45 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed ofsand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-inCharge.60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern |
| 46 | Providing and fixing of 14-16mm thick machine cut, machine polished Marble stone of approved quality wash basin counter top, vanities, kitchen counters about 600mm wide fixed and bedded over 14-16 mm thick Indian Marble; with mirror polished Marble fascia in verticle profile as detailed in drawing. Stones for 200mm wide fascia fixed with epoxy adhesive; exposed faces / edges moulded, rounded / chamfered, mirror polished etc. complete to the approval of the PM. All junctions shall be sealed with silicon sealant. Further to include required GI framing, drilling, cutting of holes, SS pins, anchors, clamps, finishing junctions with plaster etc. complete as directed by the PM to his entire satisfaction. Crema noce marble stone counter. (Basic Rate - 450/Sqft) |
| 47 | Providing and fixing 18mm thick Gang Saw Cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, edge moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. Area of Slab over 0.50 sqm. (Basic rate- Rs. 290 /sqft.) |
| 48 | Passive Fire Protection System for Curtain wall joint sealing:Supplying, Providing and application of sprayable Fire-rated joint spray to seal gap between horizontal slab & curtain wall to provide minimum 2 hours of fire rating when tested as per ASTM E 2307 standard . The product to have up to 50% Movement Capability. The product should pass the 500 cycles requirement as specified by ASTM E 1399 class II. The product shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. If none of UL test certificate comply with actual application, an Engineering Judgement document prepared by a qualified personnel and based on nearest third party tested & approved systems like UL test certificates & in accordance with IFC guidelines shall be produced by manufacturer. Firestop installation shall be done in accordance with the reference UL certificate or Engineering Judgement document. The Supplying and Installation of Rockwool (Density-100 kg/m3) along with submission of Metarial Test Certificate as per standard norms, prior to firestop coating application is in Contractor"s scope. Supplying, Providing and application of acrylic sealant in additional gap between the floor and the GI tray is included in the mentioned rate . Sealant shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96. N.B: Supply and fixing of metal cradle (GI tray), nut-bolts/ screws etc will be done by Contractor only through seperate line item. |
| 49 | Providing and fixing upto 400mm wide 10-12mm thk Granite sill on Pardi wall with support of 16 mm thick Cement Fiber board which shall be fixed on existing Pardi wall and Aluminium transum of the external facade frame work, the granite shall be pasted to the Cement fiber board by means of appropriate adhesive as approved. The edge of the sill shall have straight edge and to be polished. Classic Marble,Nitco or equivalent. (Basic Rate -165/Sqft) |
| 50 | GI tray installation: Supply & installation of GI tray of 0.8 mm thickness at the smoke seal (pardi wall juction between facade wall and pardi wall) in hat shape with proper fixing of the tray at the pardi wall & aluminium transom (facade side) without any damage to facade system. The Leveling of the pardi wall by chipping/ hacking/ concreting etc with respect to mid level of the lower transom is in the scope of the contractor. Tray width shall range shall range upto maximum of 450 width. |
| 51 | Ceiling Works |
| 52 | Providing and fixing 12.5mm thick plain or coffered Gypsum False Ceiling manufactured of approved make on G.I. frame work, in G.I. vertical supports at every 450mm c/c and horizontal runners at every 900mm c/c in SS screws to proper line and level. Cost to be inclusive of making holes and required framing for fixing electrical fixtures, A.C. grills. Area of electrical fixtures will be paid full with ply on top of ceiling fixed to G.I. supports to receive spotlights including cutting hole etc., complete. G.I. metal frame to be of 22 gauge folded strip of 50mm width to be used. All complete as per PM"s instructions and specifications. The grid of frame work to be supported at every 1500mm x 1500mm interval by M.S. Rod anchored to the slab to support the G.I. framework. All vertical G.I. framework to be anchored to the slab by means of anchor fasteners including all lighting troughs, coffers, cornices and all other related works. Cost to be inclusive of necessary scaffolding required towards the same. Rate to include finishing with two coats of putty and Emulsion paint in approved shade, colour and make.No vertical dimensions of false ceiling to be paid for separately, vertical drop upto 600mm and false ceiling behind cornices shall not be measured and paid seperately. |
| 53 | Providing and fixing in true horizontal level Mineral fibre false ceiling system manufactured by M/s. Knauff or equivalent using hot dipped galvanized steel section, exposed surface with pre-coated capping, main tee of size 24 x 32 mm, having 0.27 mm gauge at every 1200 mm. centre to centre maximum and rotary stitched cross tee of size 24 x 27 mm, having 0.27 mm gauge at every 600 mm c/c. and sub cross tee of size 24 x 27 mm, having 0.25 mm gauge at 1200 mm c/c. and wall angle of size 19 x 19 mm., having 0.35 mm gauge fixed to the periphery of the wall. The above grid is suspended at every 1200mm c/c. in both directions using 2.0 mm. thick pre-straightened GI wire laying FINE FISSURED TEGULAR Edge ceiling tiles manufactured by M/s. Armstrong World Industries, of size 600mm 600mm x 20mm having NRC 0.70, Light reflectance of 85%, thermal conductivity k = 0.052-0.057 W/m0K, Humidity Resistance of 99%, having Fire Performance CLASS O / CLASS 1 (BS 476), surface having 3 coats of approved paint with Fine Fissured, back of the tile duly sanded and finished with a coat of protective paint over the formed grid complete etc. as per approved manufacturer"s specifications and directions of the PM. |
| 54 | Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture"s specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process. |
| 55 | Providing and Fixing openable laminate trap door of size 600x600mm constructed with 12mm thickness of MDF (of approve make) finished with laminate (of approve make and shade). All complete as per PM"s instruction and specs. |
| 56 | Providing and fixing 300- 600 mm wide x300mm-600 mm height as per size specific pelmet in 18mm thk Marine PLY of approved make and confirming to IS 3087, including top cover of fixing of approved 1mm thick Lamiante, including fixing with 25x3 mm M.S. Flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete. PLY make from Greenply,Century or Anchor make. |
| 57 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 58 | Supply and installation of colour coated LYSAGHT® TRIMDEK® profile sheet of nominal 1015 mm cover width, 1072 mm overall width and nominal 28 mm deep ribs with subtle square fluting in the five pans at nominal 203 mm centre-to-centre. The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap. The feed material shall be of 0.50 mm Total Painted Thickness (0.42 mm Base Metal Thickness) COLORBOND® XRW steel- High tensile with min 550 MPa yield strength, metallic hot-dipped coated with Al-Zn alloy (55% Aluminium, 43.5% Zinc, 1.5% Si) as per AS1397 / IS15961 - ZINCALUME® AZ150 (min. 150 g/m2 total on both sides) with Super Durable Polyester COLORBOND® steel XRW quality paint system of approved colour, suitable for exterior application conforming to AS/NZS 2728 type-4 / IS15965 class 3 ofTata BlueScope Steel make. The sheet shall have a total coating thickness of 35 microns, Super Durable Polyester COLORBOND® XRW with Thermatech™ solar reflectance technology quality paint system of 20 microns on exposed surface and 5-micron reverse polyester coat on back surface over 5-micron primer coat on both surfaces. The paint system would have stable resin & inorganic pigments for paint durability and is lead and other heavy metal free for rainwater harvesting. The steel sheet shall have brand marking of “LYSAGHT TRIMDEK® 0.50 MM TPT/ 0.42 MM BMT-A Product of Tata BlueScope Steel Ltd” along with batch number on back side at regular interval confirming genuineness of the material.Supply and installation of Rockwool Insulation of 50mm thickness Product: Fibre Rock wool InsulationThickness: 50 mm ;Density: 48 Kg/cum (48 kg/m3) ; Confirming to:IS: 8183. Supply and installation of Weld Mesh of 50mm x 50mm size of 2.00mm thickness Galvanized Iron. Supply and installation of Flashings in COLORBOND® XRW 0.50 MM TPT (0.42 MM BMT) upto 610 mm girth. Flashings in COLORBOND® XRW 0.50 MM TPT (0.42 MM BMT) upto 1220 mm girth included. All inclusive to complete the job in all aspects as per directive of EIC. |
| 59 | Wall Paneling, Partition Works & Joinery Works |
| 60 | Providing and fixing Fibre glass wool - 64 mm thick - 32 Kg / cum of approved make conforming to IS - 8183 / BS 3958 / ASTM C 612 on the spandrel panel area ie. behind the glass. These wool should be covered with Black glass tissue - 0.50 mm thick. (Nominal Mass - 60 Kg/cum) to conform Non combustibility Class - fire rating to BS 476 - part 7 & IS 3808 and fixed by using aluminium angle / channel of required size as base and the wool shall be tied with 22 gauge G.I. wire in criss-cross manner into aluminium or Galvanized angle / Channel to the structure and shall be covered with colour Black Painted GI sheet tray 1 to 1.2 mm thick . Fibre glass wool should be fixed to the main aluminium frame work (i.e behind the spandrel panel glass area). |
| 61 | Providing, constructing & fixing in place 11mm thick MDF board Partitions of overall thickness 75mm thk. with aluminium framing tube of size 25x50mm for verticle members and 25 x 50 mm for horizontal members, tube thickness of 1.2mm . vertyicle framing at 450mm c/c and horizontal frame to achive 450 x 610mm grid size. covered with 12mm thick MDF board (conforming to IS 12406) of approved make on both sides.Framming members are to fixed witrh"L" Clamps at joints and secured to rcc soffits and floor with anchor Fastner and metal Screws. All other salient features such as pattas grooves, inlay pattis & extra frame work and all other features indicated in drawing or as per instructions of PM to be the same as items of panelling. Mode of measurements also to be same as that of mentioned in panelling items. Cost of partition also to include providing, constructing & fixing ply frame with necessary rebates as required to enable fixing doors(on 3 sides of opening produced). All complete as per PM instruction and specifications. Cost also include 50mm thick glass wool insulation of 48kg/cum density inside partitions.cost also to include 50mm thick glass wool insulation(of approved make) as specified in drawings as per instruction of PM.Mode of measurements shall be as per Specifications. openings of size more than 0.5sqm shall not be counted for measurement for payment. |
| 62 | Providing and Fixing in place 12.5 mm thk Gypsum partitionof overall thickness 75mm thk. with aluminium framing tube of size 25x50mm for verticle members and 25 x 50 mm for horizontal members, tube thickness of 1.2mm. Cost to also include 50mm thick glass wool insulation (of approved make) wherever specified in drawings as per instruction of PM. Edges of the additional panel to be properly cut and finished. Necessary cutout etc. to be provided wherever required towards Services. |
| 63 | Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). 6 mm thick Cement fiber board as per IS: 14862 sqm |
| 64 | Providing and fixing 12mm thick BWP Plywood of 710 Grade of Green Ply Industries make, for panelling upon MDF . |
| 65 | Providing and fixing feature wall in wire cut bricks of size 75x115x225 mm approx including laying with 6mm steel in mortar as specified by engineer in charge. |
| 66 | Providing, making and fixing Hard wood door frames made out of approved quality teak wood, kiln-seasoned, anti-termite treated, shaped, grooved, mitered joint arrangement including use of exterior quality approved water repellent adhesive, GI screws, pins, etc. Also to include White enamle paint in approved colour and shade, surfaces of frame in contact with masonry/concrete surfaces shall be painted with one coat of hot bitumen of approved quality, 3 nos. (minimum) GI holdfast (split end 225mm x 75mm x 2 mm thick) on each side of frame well-grouted with cement concrete mix in a ratio of 1:2:4 (1 Cement : 2 Sand : 4 Aggregate), etc. all complete at all leads, lifts, heights as per detailed specifications to the entire satisfaction of the PM. 100mm x 60mm |
| 67 | Providing and fixing factory made 38mm thick solid core flush shutters conforming to IS 2202 Part I, internally lipped, with exterior quality synthetic adhesive as manufactured by M/s Anchor or equivalent approved make.Further vision pannel as per approved drawing of tentative 10mm thick glass size of 250x250mm (is inculsive in these rate) and shutter shall be finished with approved 1mm thick laminate on both sides, shade and colour and design, edges of shutters shall be provided with 48mm x 6mm thick teakwood beading using exterior quality synthetic adhesive, headless GI nails, screws, beading finished with melamine polish, etc. (Beading Kiln seasoned, antitermite treated) including ironmongeries as per schedule and drawings all complete to entire satisfaction of the PM. Single leaf door shutter (opening size - 600-900mm-1000mm to 1050mm x 2975mm) Ironmongery of approved make: a) S.S ball bering butt hinges 102mm x 76mm x 3mm - 3 Nos. b) SS mortise main door lock - 1 Nos. c) SS Tower Bolt 150mm long - 1 No e) SS Door Stopper - 1 No. f) SS Pull handle 450mm long - 1 pair |
| 68 | Providing and fixing factory made 42mm thick solid core flush shutters conforming to IS 2202 Part I, internally lipped, with exterior quality synthetic adhesive as manufactured by M/s Anchor or equivalent approved make.Further vision pannel as per approved drawing of tentative 10mm thick glass size of 250x250mm (is inculsive in these rate) and shutter shall be finished with approved 1mm thick laminate on both sides, shade and colour and design, edges of shutters shall be provided with 48mm x 6mm thick teakwood beading using exterior quality synthetic adhesive, headless GI nails, screws, beading finished with melamine polish, etc. (Beading Kiln seasoned, antitermite treated) including ironmongeries as per schedule and drawings all complete to entire satisfaction of the PM. Single leaf door shutter (opening size - 600-900mm-1000mm to 1050mm x 2975mm) Ironmongery of approved make: a) S.S ball bering butt hinges 102mm x 76mm x 3mm - 3 Nos. b) SS mortise main door lock - 1 Nos. c) Concealed door closer of DORMA / HAFELEmake d) SS Tower Bolt 150mm long - 1 No e) SS Door Stopper - 1 No. f) SS Pull handle 450mm long - 1 pair |
| 69 | Providing and fixing 6mm thick Mirror of approved make over paneling/partition/wall fixed on 18mm thick MDF with 3M tape, including beveling of mirror edges,countersunk SS screws, wood beading and edging etc. all complete as per drawings and to the entire satisfaction of PM. |
| 70 | Providing, supplying and fixing 2 hours fire rated door with pressed metal frame 143mm x 57mm size out of hot dip galvanized mild steel sheet of 1.6mm thickness including required angle threshold of hot dip galvanized mild steel angle of section 35x 35mm, or base ties of 1.25mm pressed hot dip galvanized mild steel welded or rigidly fixed together by mechanical means, Frames shall be fixed with 3 nos. G.I. holdfast 200 x 30 x 3 mm with split end on either side and well grouted with cement concrete mix 1:2:4; adjustable lugs with split end tail to each jamb, including stainless steel ball bearing butt hinges (4" x 3" x 3mm) of approved make strengthened with SS pins, lock strike-plate, shock absorbers as specified and 46 mm thick single/ double leaf shutter made out of minimum 1.25 mm thick galvanised sheet insulated with mineral wool for required fire rating and tested as per latest IS specification IS 3614 Part-II.Further include priming with Zinc-Phosphate Stoving Primer and finishing with Polyurethane Aliphatic grade paint in approved shade and colour complete, at all levels and locations, as per drawing to the entire satisfaction of the PM. Ironmongeries of approved make.a) SS ball bearing butt hinges of size 4" x 3" x 3mm thick - 4 Nos. b) SS Pull handle D type/ panic bar 600mm long, 32mm dia - 2 Pair c) SS mortise dead lock with euro profile cylinder- 1 No. d) SS Tower Bolt 300mm long -1 no. e) Rack and pinion Door closer - 1 No. of approved make Shakti Hormann, Tata pravesh or equivalent. |
| 71 | Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing sizeshall not be more than 1100x2200 mm (w x h) or2.42 M2. |
| 72 | Providing and fixing factory made uPVC white colour casement/ Casementglazed door comprising of uPVC multi-chambered frame,sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanizedmild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on EA side of panels along with zinc plated mild steel multi point lockinghaving transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall beacceptable.Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension, door lock to be included.. |
| 73 | Providing and fixing factory made uPVC white colour casement/casement glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.:: Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 M2.) |
| 74 | Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with1.60 ± 0.2 mm thickgalvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile),appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with keyon one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.:::Three track three panels sliding WINDOW/DOOR with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series)frame 116 x 45 mm & sash 46 x 82 mmboth having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm). Providing and fixing casement handle with locks made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : 5.0 mm thick glass panes (weight not less than 12.5 kg per sqm). |
| 75 | Glass doors frames of 60 x 60 mm in extruded tubular aluminium duly powder coated/ annodized and10 mm thick clear toughened glass door. The door will be provided with hinges, 450 mm H handle, exposed door closer and floor mounted door stopper, floor spring all of approved make. -Single leaf door - Structural opening size - 1200mm x 2975mm as per site requirement and directions of EIC |
| 76 | Providing and fixing Wall paper of approved make and design on existing wall/Partition/Panelling surfaces. Basic cost of wallpaper to be Rs. 150/- per sqft. |
| 77 | Electrical Works |
| 78 | Supply, Installation , Testing & Commissioning of Circuit wiring through PVC Heavy Duty Conduit as required with all the accessories, screws,spacers,clamps, z-sections. The wires shall be laid directly from LDB/PDB/USPDB to individual Switch Board or Power Socket, which includes Three/Five wires i.e. including the earth continuity conductor/wire Circuit wiring also includes wiring from one Switch Board to another Switch Board or from First Power Socket to another/next Power Socket. All the circuit wires shall be laid through PVC conduits/GI Trunking already laid on surface/ concealed as per site requirenent and as specified in drg. This item is inclusive of PVC conduits, Cu wires,Circular boxes etc. The complete job includes the following : -- i) Laying of 18swg, GI, Pull wire through each length of Conduit, from one end to another end. ii) The no of wires to be laid through each conduit shall be with respect to the size of conduit & the wires, It should be as per IS Relevant standards only iii) Each PVC Conduit shall carry wires only one phase out of any of the Three phase wires, Seperate Conduit has to be used for each phase of wire iv) necessary chipping and finishing for any concealed type wiring:: a) Wiring in 25mm FRLS HMS PVC Conduit as required with all accessories, screws,spacers,clamps, z-sections etc., b) 1100V grade FRLS PVC insulated multistranded Cu wires. c)Insulated or base protective earth.: Primary Circuit wiring for all Light points using 2x2.5 + 1x2.5PE Cu PVC Wires. |
| 79 | Supply, Installation , Testing & Commissioning of Circuit wiring through PVC Heavy Duty Conduit as required with all the accessories,ws,spacers,clamps, z-sections The wires shall be laid directly from LDB/PDB/USPDB to individual Switch Board or Power Socket, which includes Three/Five wires i.e. including the earth continuity conductor/wire Circuit wiring also includes wiring from one Switch Board to another Switch Board or from First Power Socket to another/next Power Socket. All the circuit wires shall be laid through PVC conduits/GI Trunking already laid on surface/ concealed as per site requirenent and as specified in drg. This item is inclusive of PVC conduits, Cu wires,Circular boxes etc.The complete job includes the following : -- i) Laying of 18swg, GI, Pull wire through each length of Conduit, from one end to another end. ii) The no of wires to be laid through each conduit shall be with respect to the size of conduit & the wires, It should be as per IS Relevant standards only iii) Each PVC Conduit shall carry wires only one phase out of any of the Three phase wires, Seperate Conduit has to be used for each phase of wire iv) necessary chipping and finishing for any concealed type wiring: Secondary Circuit wiring with 2nos. of 1.5sqmm+1 nos 1.5sqmm (P/N & E) FRLS grade PVC insulated Cu wires. |
| 80 | Supply, Installation , Testing & Commissioning of Circuit wiring through PVC Heavy Duty Conduit as required with all the accessories,ws,spacers,clamps, z-sections The wires shall be laid directly from LDB/PDB/USPDB to individual Switch Board or Power Socket, which includes Three/Five wires i.e. including the earth continuity conductor/wire Circuit wiring also includes wiring from one Switch Board to another Switch Board or from First Power Socket to another/next Power Socket. All the circuit wires shall be laid through PVC conduits/GI Trunking already laid on surface/ concealed as per site requirenent and as specified in drg. This item is inclusive of PVC conduits, Cu wires,Circular boxes etc.The complete job includes the following : -- i) Laying of 18swg, GI, Pull wire through each length of Conduit, from one end to another end. ii) The no of wires to be laid through each conduit shall be with respect to the size of conduit & the wires, It should be as per IS Relevant standards only iii) Each PVC Conduit shall carry wires only one phase out of any of the Three phase wires, Seperate Conduit has to be used for each phase of wire iv) necessary chipping and finishing for any concealed type wiring: Primary Circuit wiring with 2nos. of 4 sqmm+1 nos 1.5sqmm (P/N & E) FRLS grade PVC insulated Cu wires. |
| 81 | Supply, Installation and commissioning of 1200mm dia Ceiling fans, Make- Havells, Bajaj, Orient, Crompton etc. |
| 82 | Supply, Installation and commissioning of 400-500 mm dia high speed, heavy duty Kitchen Exhaust fans. Make- Havells, Crompton, Usha etc. |
| 83 | Supply, fixing in existing DB and commissioning of 40A 4 pole MCB. Make- L&T, ABB, Schnieder etc. |
| 84 | Supply, fixing in existing DB and commissioning of 10/16A SP MCB. Make- L&T, ABB, Schnieder etc. |
| 85 | Supply, Installation , Testing & Commissioning of Recessed Mounted/ INDOOR LED Type Lighting Fixtures. Including all support structure/ stripe /rod etc for hanging light etc: 7W-9w LED recessed spotlight , housing made of Aluminium:CCT-3000K, CRI>80. Make: Havells, Philips, Jaquar, Wipro etc. Note: Sample should be provided before placing the order to EIC. |
| 86 | Supply, Installation , Testing & Commissioning of various Type of Hanging/Surface/ Recessed Mounted/ INDOOR LED Type Lighting Fixtures. Including all support structure/ stripe /rod etc for hanging light etc: 5w/mtr Strip Light, CCT-3000K |
| 87 | Supply Installation & Commissioning of Extruded Aluminium LED batten available in 2ft & 4ft run length with multiple lumen packages and suitable for Surface, Wall & Conduit mounting (with accessories). 20-25Watt, CCT-3000k/4000K. |
| 88 | Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with chain & all necessary accessories. All Light Fixures with Electronic Ballast THD <10%. 40W Ceiling mounted/suspended box type LED light fixture similar to Bajaj make LED CONNECT - BPTX 40W LED 4F or its equivcalent item of Philips/ ABBY Lighting/Jaquar Lighting/ Havels/Crompton/Syska as per tender specification & Clients/EIC approval.Fixture Code: LF15 |
| 89 | Supply, Installation, testing and commissioning of Modular Type Switch and Sockets with necessary face plates & Back Box using all required hardware, wall chasing and finsihing after fixing,internal wiring and connections using lugs,ferruling::1 no. 16Amp switch with & 1no. 16A sockets with necessary face plates. Make: MK, Legrand or equivalent. |
| 90 | Supply, Installation, testing and commissioning of Modular Type Switch and Sockets with necessary face plates and back Box using all required hardware,wall chasing and finsihing after fixing internal wiring and connections using lugs,ferruling::4 no. 6Amp switch with necessary face plates. Make: MK, Legrand or equivalent. |
| 91 | FA System-I/O Device-Fire Detector Unit (Supply of a complete set consisting of a Fire Detector along with base (as applicable) & other accessories for Fire Alarm System including associated services. Make-Honeywell, Model- TC806B3010. |
| 92 | FA System-I/O Device-Manual call Point Unit (Supply of a complete set consisting of a Manual Call Point (MCP) along with base (as applicable) & other accessories for Fire Alarm System including associated services. Make-Honeywell, Model-XLS/MCP/GLASS |
| 93 | FA System-I/O Device-Hooter Cum Flasher Unit (Supply of a complete set consisting of a Hooter cum flash light (strobe) indicator along with base (as applicable) & other accessories for Fire Alarm System including associated services. Make-System Sensor, Model-SYS-HS. |
| 94 | Installtion Testing and commissioning of occupancy sensor/lighting sensors. All necessary loop wiring with the lighting circuits shall be in the scope of work of the contractor. The sensor only will be supplied by the client. |
| 95 | FA System-I/O Device-Switch Detector Unit (Supply of a complete set consisting of a Switch Detector module & other accessories for Fire Alarm System including associated services. Make- Honeywell, Model- TC809 / B1008 |
| 96 | FA System-I/O Device-Relay Output Unit (Supply of a complete set consisting of a Relay output module & other accessories for Fire Alarm System including associated services. Make- Honeywell, Model noTC810R1024 |
| 97 | FA System-I/O Device-Fault Isolator Unit (Supply of a complete set consisting of a Fault Isolator module along with base (as applicable) & other accessories for Fire Alarm System including associated services. Make-Honeywell, Model-TC811A1006. |
| 98 | SITC of No touch of stainless steel IP-55 Ingress Protection / SUS 304 Stainless steel Plate key switch for access control system. The Switch should have NO/NC/COM relay output which can be used as per design requirements with Twin led backlight White – Power OFF BLUE – Power ON (Standby) Green – Power ON (Active) for sensor standby or approached, Optical / Infrared Technology, detection Range- 0.1-10cm. Operating Voltage- 12 V DC . Make-Schutz, Model-IIRDR-02SS |
| 99 | SITC of key lockable manual switch of stainless steel grade 304, Load current- 3A with 2 NC/2 NO/ 2 COM contact. Make-Schutz, Model-IKOS-33-D. |
| 100 | SITCof Emergency door release Break Glass Units, wired type, 18-26 V DC, 3amp of FR polymer material, outer Body- ABS Plastic. Operating Temperature- - 30 deg c to 70 deg c,Dimension- 86 x 86 x 53 mm, Mounting- Flush or surface, IP-24D. Make- MAke-Schutz, Model-IEDR18-BS(G) |
| 101 | SITC of Magnetic Door Sensor Self Adhesive type, Sensing Distance-20mm wide gap, Magnet-NdFeB, Color- White, Make- Schutz, Model-IEMC-SMA. |
| 102 | SITC of wiegand reader Module controller for access control system with 2 controlled inputs, Controlled on 4 states (open, close, cut, short), Controlled i/p supply current-0-3mA,Controlled inputMin detection time-250msec, Readers tamper inputs-2, Power supply output for readers- Voltage: 12V +/-15% (line voltage) ,Current: 200mA Max (per channel), Voltage-10V...+14V (internal Power supply), Mounting- Din rail type, Environmental temperature for correct operation--10 - 55°C, Number of outputs-2. Make-Honeywell Temaline, Model-TK_S014M. |
| 103 | Supply and installation of 2C x 1.5 sq mm Unarmoured cable of Make-Masterflex, type-2Cx1.5 SQMM, no of core-2 core, cross-sec. area-1.0 sqmm., Conductor type-5, no of strand-32 no/mm, Voltage rating-1100V, Material of Conductor-Annealed Bare copper conductor, Insulation Material-PVC (Type-A), Nominal Thickness-0.60 MM, Outer Shield Material- ST-1, thickness-0.9mm & colour-Red, Appr. Overall Dia. of Cable(tolerance +/- 1mm) - 8.5 +/- 0.1 mm, Conductor Resistance- 19.5 ohm/km, Volume Resistance(min.) M .Ohm/Km - 1X1013 ohm-cm, Applicable Standards - IS-8130, IS-5831, IS-694, IEC 60332-1. |
| 104 | Supply and installation of 3C x 1.0 sq mm Armoured cable of Make-Masterflex, type-3Cx1.0 SQMM, no of core-3 core, cross-sec. area-1.0 sqmm., Conductor type-5, no of strand-32 no/mm, Voltage rating-1100V, Material of Conductor-Annealed Bare copper conductor, Armour Material &Size-G.I. ROUND 0.90 MM, Inner Sheat Material- ST-1, Inner Sheath Thickness (min)-0.3mm, Insulation Material-PVC (Type-A), Nominal Thickness-0.60 MM, Outer Shield Material- ST-1, thickness-11.0mm & colour-Black, Conductor Resistance- 19.5 ohm/km, Volume Resistance(min.) M .Ohm/Km - 1X1013 ohm-cm, Applicable Standards - IS-8130, IS-5831, IS-1554-1, IS-3975. |
| 105 | SITC of CAT-6 Cables. Make-Dlink, model-NCB-C6UGRYR-305, type-CAT6 UTP Cable with operating temperature range- #20°C to +75°C |
| 106 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 107 | Cable Tray : Supply & installation of Hot Dip Galvanised Bolted Ladder type G I cable trays with 75mm height with 2.0 mm thickness & necessary G I supporting frame/Tie rods, fastners,screws, Tray bends etc. as required for Electrical & LV cables as specified & shown on drawings. 200mm wide single horizontal/vertical tier. |
| 108 | Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Recess mounted glare free round LED Downlight with pressure die cast Aluminium housing and high transmitive Polycarbonate diffuser, (15W- 18 W), 1500-1600 Lumens(minimum), IP-20, CCT/CRI- 5700K/80, Electronic ballast, similar to Wipro make - Mollis-LD06-221-XXX-40-XX or its equivalent item of Philips/Jaquar lighting/ Lighting technology/Havels/ as per tender specification & Clients/EIC approval |
| 109 | Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Recess mounted glare free round LED Downlight with pressure die cast Aluminium housing and high transmitive Polycarbonate diffuser, (15W- 18 W), 1500-1600 Lumens(minimum), IP-20, CCT/CRI- 4000K/80, Electronic ballast, similar to Wipro make - Mollis-LD06-221-XXX-40-XX or its equivalent item of Philips/Jaquar lighting/Lighting technology/Havels/ as per tender specification & Clients/EIC approval |
| 110 | Installation, testing & commissioning of Single phase-2 KVA inverter with:15 Min battery backup complete with battery rack and necessary accessories. Make :Consul Neowatt, Luminous |
| 111 | Installation, testing & commissioning of Distribution Bords, termination of power cables with necessary earthing from nearest Earthing Bus. |
| 112 | Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations of Circular LED Post Top offering excellent uniform illumination and aesthetics, made up of Pressure die cast alluminium body and opal PC CoverUnique ring shape LED Engine ensuring soothing, glare free light distribution, Finish-Pure polyester powder coated matt Grey finish after phosphochromate treatment Unique design detachable gear tray with Potted electronic LED driver with APFC, APFC, (SMPS based constant current supply), lower THD, Lumen efficacy of LED >140 lm/W and viewing angle of 120° to ensure better uniformity, Operating voltage range: 140 V - 270 V IP-66, IK-07. 60Watt, 3000/4000K., Dia-450mm. similar to Havells Make-SL PT BL CL 24 66 60 W or its equivalent of Philips, Lighting Technoilogyetc. Note: Light Sample should be provided to EIC before placing the order. |
| 113 | Supply, Installation and commissioning with necessary earthing of aesthetically designed decorative hot dipped galvanised mild steel step pole with grey colour finish. Compatible for all Havells post top range. Housing-Hot dipped galvanized mild steel step pole. Elliptical Aluminum sheet with HAVELLS in grey color is riveted to the pole. Standard height of 4mtr. Finish-Grey UV stabilized pure polyester powder coating after hot dipped galvanizing. Upper section of pole with length 2852mm +30mm with Ø75.4 to Ø77 having Wall Thickness 2.9 to 3.2 mm, lower section of pole with length 1065±15 mm having Ø138.3 to Ø141 Wall Thickness 3.2 to 3.4 mm and having decorative casting element of 83mm ± 3mm height, total pole weighting 25 kg + 5%. Pole Window is Plasma cut & duly chamfered opening window of 300x110 mm for terminal connections & mounting accessories. Elliptical Aluminum sheet with HAVELLS in grey color is riveted to the pole. Window cover is fitted with allen screws to the pole. Mounting base of the pole is Mild steel base plate of Ø 268 mm with 4 no. elliptical holes of 20x42 mm on 210 mm PCD suitable for M12 bolts. Havells make- ECO Pole 4mtr Decorative Poleor equivalent of Philips, Lighting Technology. |
| 114 | Earth wire/strips Supply & laying Cu/AL/GI earthing strips for interconnecting the earthing stations, panels, DB"s etc. in built-up trenches, on walls/ceiling, buried in ground, generally as specified & shown on drawings complete with;a) Fixing accessories.b) Corrosion protection of buried conductors with bituminous coating and covered with PVC tapes. of size--25 x 3 mm GI |
| 115 | Earth wire/strips Supply & laying Cu/AL/GI earthing strips for interconnecting the earthing stations, panels, DB"s etc. in built-up trenches, on walls/ceiling, buried in ground, generally as specified & shown on drawings complete with;a) Fixing accessories.b) Corrosion protection of buried conductors with bituminous coating and covered with PVC tapes. of size--8 SWG CU |
| 116 | Plumbing & Sanitary fixtures |
| 117 | Supply & intallation of Concealed cistern assembly with tank and dual flushing mechanism for 4.5ltr long flush and 3 ltr short flush as per green building norms ; of any of the below make & model- .VITRA:Cat No.748-1850-01IND |
| 118 | Installation and commissioning of Soft touch two button flush actuation pushplate as wall mounted upper trim for concealed cistern ;of the below make & model- VITRA: Cat No 740-0580IND . Supply of flush plate by client. |
| 119 | Intallation and commissioningof Wall-mounted white ceramic rimless WC body with matching soft close seat & cover,and vortex/high-efficiency dual flushing (4.5lt/3lt). ; of the below make & model VITRA:Cat No 7041B003H0075+110-003H909. Supply of rack bolts or any other fitting accessories as required for complete installation of W/C is inclusive in the line item. |
| 120 | Installation testing and commissioning of floor jali with provision for installation of marble/ tiles block similar to the toilet area (Square/Round) marble/ tiles. |
| 121 | Supply & intallation of Decorative glass body manual push down pump action liquid soap dispenser with CP trimmings, with screws, plugs, rossette etc for wall mount complete. |
| 122 | Intallation of SS/CP/ Brushed steel finish on brass double robe hook. Supply of robe hook by client. |
| 123 | Installation of semi-recessed type white ceramic basin of length 550 to 600 mm to mount on counter of depth 450mm or less with one tap hole of the below make & model VITRA:Cat No 5679B003H0001. Supply of wash basin in scope of client. |
| 124 | Intallation of Under counter white ceramic wash basin length & breadth will depend as per site execute to sit completely below the vanity counter; of the below make & model. VITRA:Cat No 6069B003H0012 . Supply of wash basin in scope of client. |
| 125 | Supply and Installation of Under counter white ceramic wash basin length 500mm to 600mm & breadth will depend as per site execute to sit completely below the vanity counter; of the below make & model.1.TOTO: LW548M#NW1, 2.American Standard CL0474I-6DACTLU 3. VITRA:Cat No 6069B003H0012 4.ROCA:RS327871461 5.KOHLER:2211IN-0 or equivalent |
| 126 | Supply & intallation of CP on brass connecting fixture with pop-up ceramic head complete with gaskets etc. ; of any of the below make & model Vitra: A45148 or equivalent. |
| 127 | Supply and intallation of AC powered sensor actuators conforming to green building norms for wall mounted urinals including concealed flush valve and wall mounted trim with sensor eye.; of the below make & model VITRA:310H2610 or equivalent. |
| 128 | Supply & intallation of CP on metal hand-held hygiene spray with wall mount and flexible metal pipe of the below make & model VITRA:A45704 or equivalent. |
| 129 | Supply & intallation of Premium grade matching SS/CP/Brushed steel finish on brass 2 way bibcock faucet with spout head and flange for hygiene spray complete with screws, plugs, rossette etc, wall mounted. Make Vitra or equivalent. |
| 130 | Intallation of Sensor actuated, wall mounted back inlet urinals of white ceramic including flexible hose, gaskets, hanger, mounting bolts, plugs etc complete. With independent sensor unit (to be billed seperately) ; of the below make & model- .VITRA: 5462B003H0309. Supply of urinial in client scope. |
| 131 | Supply and Fixing of 2 no"s 6mm thick Lacquered glass sandwiched urinal partition. Cost to also include necessary fixing in S.S patch fitting from Hafele or equivalent make. |
| 132 | Fixing of Wall mounted partition plate of single unit white ceramic with screws, plugs, rods, white cement etc. Supply of ceremic partition in scope of client. |
| 133 | Intallation of CP finished siphon type metal bottle trap for connecting wash basin and waste water line complete with gaskets, screws, plugs, rossette etc of the below make & modelVITRA: A45122. Bottle trap to be supplied by client. |
| 134 | Intallation and commissioning of Deck mounted AC powered sensor basin faucet with SS/CP/Brushed steel finish on brass, with aerator, for cold water only. Of the below make & model: VITRA:A47177IND.Supply of faucet in scope of client. |
| 135 | Installation of deck mounted single lever faucet with SS/CP/Brushed steel finish on brass, with aerator, for cold water only. Of the below make & model: VITRA:A41590IND. Supply of faucet in scope of client. |
| 136 | Supply and Installation of SS/CP/Brushed steel finish on metal TP roll holder with spindle and roll cover complete with screws and plugs. |
| 137 | Supply and installation of hot and cold connection pipe of 24 inch. |
| 138 | Installation and commissioning of wall mounted rainshower with SS/CP/Brushed steel finish on brass extension pipe and metal/ABS showerhead with easy clean nubs complete with screws, plugs, rossettes etc ; ofthe below make & model .VITRA:Strato Cat No A45712. Supply of shower in scope of client only. |
| 139 | Supply and installation of Wall mounted single lever mixer control panel of SS/CP/Brushed steel finish on metal to run two nos outlets running hot and cold water. Also, supply and installation of Concealed thermostatic diverter set with brass and polypropelene body with two inlet and two outlet as required for commisioning of overhead shower bearing model no. VITRA:Strato Cat No A45712. |
| 140 | Supply and installation Under counter single bowl stainless sink of thickness 1mm, with folded edge and dimensions 450mmX600mm WXL. Make - Nirali |
| 141 | Supply and installation of deck mounted Kitchen mixer faucet with SS/CP/Brushed steel finish on brass, with aerator, for hot & cold water. Of any of the below make & model: 1. TOTO: TTKC301F 2. GROHE:31230000 3.VITRA: 42148IND 4.ROCA: RT5A8125C00KOHLER:13963T-C4-VS or equivalent. |
| 142 | Installation of wall mounted Gyeser |
| 143 | Supply,installation,testing and commissioning of CPVC (Chlorinated Poly Vinyl Chloride) water supply pipes with pipe as per CTS SDR 11 (working pressure - 7 Bar @ 82 Deg C (however, testing pressure shall be 10 Bar) and 28 Bar @ 23 Deg C)for pipes from 1/2 Inch to 2 Inch. Schedule 40 Pipe to be used from 2-1/2 Inch to 6 Inch. Pipes shall be joined using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers,Unions, Reducers, brushings etc. including transition fittings (connection between CPVC & metal pipe/GI) i.e. Brass Adaptors (both Male & Female threaded) conforming to ASTM D-2846. ASTM F441 with only CPVC solvent cement conforming to ASTM F-493. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings.(In Internal toilet). Cost shall be inclusive of (a)Making maximum of 7.5 x 7.5 cm chasing in wall and floors for the pipe, making good the same by using 1:1 cement mortar over the wire mesh and providing protection to embedded pipes and fittings (in wall chase) by wrapping two layers of 400 micron polythene sheet including proper overlaps on joints complete as required. Hard PVC pipe sleeves suitable higher size shall be provided wherever the pipes are crossing the walls / floors slab and sealing the sleeves with glass wool in between and sealant compoundat either end all as per Project Manager"s / Consultant requirement. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings.nical Manual of manufacturer of pipes & fittings. (for hot and cold water inside the toilet)::15 mm |
| 144 | Supply,installation,testing and commissioning of CPVC (Chlorinated Poly Vinyl Chloride) water supply pipes with pipe as per CTS SDR 11 (working pressure - 7 Bar @ 82 Deg C (however, testing pressure shall be 10 Bar) and 28 Bar @ 23 Deg C)for pipes from 1/2 Inch to 2 Inch. Schedule 40 Pipe to be used from 2-1/2 Inch to 6 Inch. Pipes shall be joined using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers,Unions, Reducers, brushings etc. including transition fittings (connection between CPVC & metal pipe/GI) i.e. Brass Adaptors (both Male & Female threaded)conforming to ASTM D-2846. ASTM F441 with only CPVC solvent cement conforming to ASTM F-493. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings.(In Internal toilet). Cost shall be inclusive of (a)Making maximum of 7.5 x 7.5 cm chasing in wall and floors for the pipe, making good the same by using 1:1 cement mortar over the wire mesh and providing protection to embedded pipes and fittings (in wall chase) by wrapping two layers of 400 micron polythene sheet including proper overlaps on joints complete as required. Hard PVC pipe sleeves suitable higher size shall be provided wherever the pipes are crossing the walls /floors slab and sealing the sleeves with glass wool in between and sealant compound at either end all as per Project Manager"s / Consultant requirement. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings.nical Manual of manufacturer of pipes & fittings. (for hot and cold water inside the toilet)::20 mm |
| 145 | Supply,installation,testing and commissioning of CPVC (Chlorinated Poly Vinyl Chloride) water supply pipes with pipe as per CTS SDR 11 (working pressure - 7 Bar @ 82 Deg C (however, testing pressure shall be 10 Bar) and 28 Bar @ 23 Deg C)for pipes from 1/2 Inch to 2 Inch. Schedule 40 Pipe to be used from 2-1/2 Inch to 6 Inch. Pipes shall be joined using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers, Unions, Reducers, brushings etc. including transition fittings (connection between CPVC & metal pipe/GI) i.e. Brass Adaptors (both Male & Female threaded) conforming to ASTM D-2846. ASTM F441 with only CPVC solvent cement conforming to ASTM F-493. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings.(In Internal toilet). Cost shall be inclusive of (a)Making maximum of 7.5 x 7.5 cm chasing in wall and floors for the pipe, making good the same by using 1:1 cement mortar over the wire mesh and providing protection to embedded pipes and fittings (in wall chase) by wrapping two layers of 400 micron polythene sheet including proper overlaps on joints complete as required. Hard PVC pipe sleeves suitable higher size shall be provided wherever the pipes are crossing the walls /floors slab and sealing the sleeves with glass wool in between and sealant compound at either end all as per Project Manager"s / Consultant requirement. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings.nical Manual of manufacturer of pipes & fittings. (for hot and cold water inside the toilet)::25 mm |
| 146 | Supply,installation,testing and commissioning of CPVC (Chlorinated Poly Vinyl Chloride) water supply pipes with pipe as per CTS SDR 11 (working pressure - 7 Bar@ 82 Deg C (however, testing pressure shall be 10 Bar) and 28 Bar @ 23 Deg C)for pipes from 1/2 Inch to 2 Inch. Schedule 40 Pipe to be used from 2-1/2 Inch to 6 Inch. Pipes shall be joined using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers,Unions, Reducers, brushings etc. including transition fittings (connection between CPVC & metal pipe/GI) i.e. Brass Adaptors (both Male & Female threaded) conforming to ASTM D-2846. ASTM F441 with only CPVC solvent cement conforming to ASTM F-493. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings.(In Internal toilet). Cost shall be inclusive of (a)Making maximum of 7.5 x 7.5 cm chasing in wall and floors for the pipe, making good the same by using 1:1 cement mortar over the wire mesh and providing protection to embedded pipes and fittings (in wall chase) by wrapping two layers of 400 micron polythene sheet including proper overlaps on joints complete as required. Hard PVC pipe sleeves suitable higher size shall be provided wherever the pipes are crossing the walls / floors slab and sealing the sleeves with glass wool in between and sealant compound at either end all as per Project Manager"s / Consultant requirement. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings.nical Manual of manufacturer of pipes & fittings. (for hot and cold water inside the toilet)::50 mm |
| 147 | Installation, fixing,jointing, testing and commissioning spun/centri C.I. pipe for soil,waste installation conforming to IS:3989 cut to required lengths including all necessary fittings and specials such as Bends, junctions, offsets, access pieces (plain or door) & vent cowl. Fixing at wall/ceiling level supported by galvanized steel clamps & hangers etc. duly epoxy coated. Making proper connection with drip seal PJS joint or pig lead joint of required depth as per manufacturer. Cutting, chases/holes in floors / walls / slab.Cost shall also be inclusive of supply and installation of fittings like bends,offsets, syphones with two coats of synthetic enamel paint of approved shade over a coat of primer. (Pipes inside toilet, kitchen )::110 mm dia.". Only CI pipe shall be supplied by client. |
| 148 | Installation, fixing, jointing, testing and commissioning spun/centri C.I. pipe for soil,waste installation conforming to IS:3989 cut to required lengths including all necessary fittings and specials such as Bends, junctions, offsets, access pieces (plain or door) & vent cowl. Fixing at wall/ceiling level supported by galvanized steel clamps & hangers etc. duly epoxy coated. Making proper connection with drip seal PJS joint or pig lead joint of required depth as per manufacturer. Cutting, chases/holes in floors / walls / slab. Cost shall also be inclusive of supply and installation of fittings like bends,offsets, syphones with two coats of synthetic enamel paint of approved shade over a coat of primer. (Pipes inside toilet, kitchen )::80 mm dia.". Only CI pipe shall be supplied by client. |
| 149 | Supply, instalation, testing & commissioning of forged brass, male or female threaded isolation control valve (Ball Valve), confirming to latest IS, PN 10, with necessary specials, union, nipples etc., to complete the job.::20mm |
| 150 | Supply, instalation, testing & commissioning of forged brass, male or female threaded isolation control valve (Ball Valve), confirming to latest IS, PN 10, with necessary specials, union, nipples etc., to complete the job.::15mm |
| 151 | Supply and application of the material at all required places where C.I Material have been used. |
| 152 | Supply,installation,testing and commissioning of sprinklers generally as specified complete with escutcheon plates: Pendent type 15/10mm/68oC Sprinklers |
| 153 | Supply,installation,testing and commissioning of UL listed & local CFO approved sprinkler flexible connection with all necessary supports & joining accessories::i) 1 or 1.5m length |
| 154 | Providing and implementing Rectification work in existing piping.::25 n.b |
| 155 | Providing and implementing Rectification work in existing piping.::32 n.b |
| 156 | Providing and implementing Rectification work in existing piping.::40 n.b |
| 157 | Hydro testing of sprinklers for full 2nd floor. |
| 158 | Installation of handrail, grab rail, etc in divyang toilet. Inclusive of all necessary fittings, screws, etc |
| 159 | Internal Piping ( 100 n.b. ): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. |
| 160 | Internal Piping ( 80 n.b.): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. |
| 161 | Internal Piping (65 n.b.): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. |
| 162 | Internal Piping(50 n.b. ): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. |
| 163 | Internal Piping( 40 n.b.): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. |
| 164 | Internal Piping (32 n.b. ): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job |
| 165 | Internal Piping (25 n.b.): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. |
| 166 | HVAC items |
| 167 | Supply, fabrication and erection of galvanised sheet metal ducting generally as specified and completely factory fabricated with:i) Hot dip Galvanised companion flanges girth angles. ii)Turning vanes. iii) Hot dip Galvanised structural support systems. iv) Closed cell neoprene gasket. vii) Making openings in walls and Closing with necessary Civil Work, finishing with suitable 2hr fire seal (Hilti/Promate). (need to necessarily included here)viii) Ducting shall be as per SMACNA Standard:::0.63mm (24 SWG) galvanised sheet steel and other accessories for example GI Angle, Tie Rod, duct connecting GI Angles etc. should be provided by the contractor. |
| 168 | Supply, fabrication and erection of galvanised sheet metal ducting generally as specified and completely factory fabricated with:i) Hot dip Galvanised companion flanges girth angles.ii)Turning vanes.iii) Hot dip Galvanised structural support systems.iv) Closed cell neoprene gasket.vii) Making openings in walls and Closing with necessary Civil Work, finishing with suitable 2hr fire seal (Hilti/Promate). (need to necessarily included here)viii) Ducting shall be as per SMACNA Standard:::0.80mm (22 SWG) galvanised sheet steel and other accessories for example GI Angle, Tie Rod, duct connecting GI Angles etc. should be provided by the contractor. |
| 169 | Supply, fabrication and erection of galvanised sheet metal ducting generally as specified and completely factory fabricated with:i) Hot dip Galvanised companion flanges girth angles.ii)Turning vanes.iii) Hot dip Galvanised structural support systems.iv) Closed cell neoprene gasket.vii) Making openings in walls and Closing with necessary Civil Work, finishing with suitable 2hr fire seal (Hilti/Promate). (need to necessarily included here)viii) Ducting shall be as per SMACNA Standard:::1.00mm (20 SWG) galvanised sheet steel and other accessories for example GI Angle, Tie Rod, duct connecting GI Angles etc. should be provided by the contractor. |
| 170 | Only Fabrication and erection of galvanised sheet metal ducting generally as specified and completely factory fabricated with:i) Hot dip Galvanised companion flanges girth angles.ii)Turning vanes.iii) Hot dip Galvanised structural support systems.iv) Closed cell neoprene gasket.vii) Making openings in walls and Closing with necessary Civil Work, finishing with suitable 2hr fire seal (Hilti/Promate). (need to necessarily included here)viii) Ducting shall be as per SMACNA Standard:::0.63mm (24 SWG) galvanised sheet steel and other accessories for example GI Angle, Tie Rod, duct connecting GI Angles etc. should be provided by the contractor. |
| 171 | Only Fabrication and erection of galvanised sheet metal ducting generally as specified and completely factory fabricated with:i) Hot dip Galvanised companion flanges girth angles.ii)Turning vanes.iii) Hot dip Galvanised structural support systems.iv) Closed cell neoprene gasket.vii) Making openings in walls and Closing with necessary Civil Work, finishing with suitable 2hr fire seal (Hilti/Promate). (need to necessarily included here)viii) Ducting shall be as per SMACNA Standard:::0.80mm (22 SWG) galvanised sheet steel and other accessories for example GI Angle, Tie Rod, duct connecting GI Angles etc. should be provided by the contractor. |
| 172 | Only Fabrication and erection of galvanised sheet metal ducting generally as specified and completely factory fabricated with:i) Hot dip Galvanised companion flanges girth angles.ii)Turning vanes.iii) Hot dip Galvanised structural support systems.iv) Closed cell neoprene gasket.vii) Making openings in walls and Closing with necessary Civil Work, finishing with suitable 2hr fire seal (Hilti/Promate). (need to necessarily included here)viii) Ducting shall be as per SMACNA Standard:::1.00mm (20 SWG) galvanised sheet steel and other accessories for example GI Angle, Tie Rod, duct connecting GI Angles etc. should be provided by the contractor. |
| 173 | Supply, installation and commissioning of Toilet exhaust fan with Automatic front shutter with copper motor ensures robust performance and rust proof body and blades(Size -8 inch).Fan should be able to mount on 150*150 mm G.I duct. Make Usha or equivalent |
| 174 | Supply and installation of continuous or discrete air grilles extruded aluminium, "powder coated as specified and complete with i) Face bars horizontal/vertical,adjustable/non-adjustable. ii) 20mm margins with PVC gasket iii) Sidewall or linear as shown in drgs::100 mm Linear grille |
| 175 | Supply and installation of continuous air grilles extruded aluminium, "powder coated as specified and complete with i) Face bars horizontal/vertical,adjustable/non-adjustable. ii) 20mm margins with PVC gasket iii) Sidewall or linear as shown in drgs::150 mm Linear grille |
| 176 | SITC of canvas material. AHU/Axial fan outlet will be fire retardant canvass cloth with provision of gauge for the measurement. |
| 177 | Commissioning & testing of VENTILATION & EXHAUST SYSTEMS in accordance with and meeting the intents of the specifications,Car park Exhaust fan-1( podium), 23000-11500 cfm. The scope of the contractor shall be to check the healthiness of theinstalled fans, mechanical checks, IR test of the fan motors, cable terminations etc. with all necessary nut bolts, tie rods as required for successfull commissioning of the sytem in totality. |
| 178 | Miscellaneous items |
| 179 | Supply and installation of WPC deck flooring of 22mm thickness WPC interlocking deck flooring tiles, pasted on underlay Poly proplene support packing (Basic Rate: Rs. 330/ sq.ft.) |
| 180 | Supply of decorative medium sized polished glossy stones pebbles of size ranging from 4cm to 8 cm for decorative areas like plaza, etc at ground floor. |
| 181 | LAWN (Carpet): Supply and installation of high density standard green carpet grass of thickness 25 mm to 35 mm. Supply and laying of good quality nursery soil over filled-up land and Fertilizers, tools & tackles as required for the installation is in contractor"s scope only. |
| 182 | Supply and installation of high stool with polyproplene seat and back with powder coated legs having dimensions as below: Overall height 1100 mm; seat height 750 mm; seat width 460 mm; support leg at 340 mm lvl. Make: Featherlite or equivalent |
| 183 | Supply and installation of 4 legged chair with polyproplene seat and back with powder coated legs having dimensions as below: Overall height 800 mm; seat width 515 mm and seat depth 500mm. Make: Featherlite or equivalent |
| 184 | Café table of size 1050mm(Dia) x 750mm (H).Table top : 25mm thick E1 Grade prelaminated table top with matching edgebanding.Table Understructure - Foldable : MS powder coated foldable under structure with X base support. Make: Featherlite or equivalent |
| 185 | Supply & Laying of aesthetically appealing flowering shrubs that matches the surroundings and uplifts the beauty of the front facia of the building as per EIC recommendation. Required Soils fertilisers like vermicompose, vermicompost, bone dust, NPK etc. and pesticide, area cleaning and all other related miscellaneous expenses shall be within this line item cost. |
| 186 | Pot Plants- Supply of different varieties of flowering potted plants (including shade loving plants) that uplifts the beauty of the surrounding area/ room. (pot height 17 inches). Plants having 1 to 1.5m hight. |
| 187 | Kitchen Equipments |
| 188 | Supply, installation, testing and commissioning of Single Stock Pot Gas Burner of SS 304 Grade Top made of 1.5 MM Sheet and Side 08 MM Leg Pipe 1.5 MM Angle Frame Mild Steel, Burner Heavy Duty, Copper Pipe, NCV Control Valve System Adjustable System (Size:24”x24”x24”) |
| 189 | Supply, installation, testing and commissioning of one burner Chinese Range having Top 1.5 MM,Leg Pipe 1.5 MM, Angle Frame Mild Steel Gas Burner, Copper Pipe NCV Control Valve System having Adjustable System. (Size: 24”x24”x34”) |
| 190 | Supply, installation, testing and commissioning of 03 Under counter Refrigerator having SS Top 1.2 MM Side SS 0.8 MM Puff Insulated Body Digital Temperature Control, Automatic System with Compressor System. (Size: 72”x12”+18”+12”) |
| 191 | Supply, installation, testing and commissioning of Over Head Shelf (Size : 72”x12”+18”+12”) |
| 192 | Supply, installation, testing and commissioning of Chapati Plate Cum Puffer having Top MS Plate RV Burner NCV Control Valve Leg Pipe 1.5 MM Side Shelf 0.8 MM. (Size: 30”x24”x34”) |
| 193 | Supply, installation, testing and commissioning of Chapati Trolley U/S 2 SS Sheet 1 MM Leg Pipe 1.5 MM Wheel System (Size: 18”x24”x34”) |
| 194 | Supply, installation, testing and commissioning of Deep Freezer Wheel System Puffing Insulated Body Top Doors Powder Cotateel Body 220 Volt Automatic System Compressor Attached. (Size: 440 Ltr; 1395x720x845) |
| 195 | Supply, installation, testing and commissioning of Work Table U/S 2 Top 1.5 MM, Shelf 0.8 MM Leg Pipe 1.5 MM Nylon Adjustable (Size: 60”x30”x34”) |
| 196 | Supply, installation, testing and commissioning of Three Sink Unit Top Tank 1.5 MM Leg Pipe 1.5 MM Outer Drain System Nylon Adjustable System |
| 197 | Supply, installation, testing and commissioning of Work Table Chapati U/S 1 Top 1.5 MM Leg Pipe 1.5 MM Shelf 0.8 MM Nylon Adjustable (Size: 24”x24”x34”) |
| 198 | Supply, installation, testing and commissioning of Garbage Table Top 1.5 MM Hole Garbage System, Leg Pipe 1.5 MM, Nylon Adjustable System |
| 199 | Supply, installation, testing and commissioning of Dish Rack Five Shelf 0.8 MM Parpurated System Leg Pipe 1.5 MM, Nylon Adjustable System (Size: 36”x18”x60”) |
| 200 | Supply, installation, testing and commissioning of Pot Rack Four Shelf, Shelf Pipe 1.5 MM Leg Pipe 1.5 MM, Nylon Adjustable System |
| 201 | Supply, installation, testing and commissioning of SS Hood with SS Filter 0.8 MM 15 Feet (Size: 72”x30”x18”) |
| 202 | Supply, installation, testing and commissioning of GI Ducting Approx Line 20’ Feet Rs. 1400/- Running Feet GI Sheet 0.6 MM |
| 203 | Supply, installation, testing and commissioning of Exhaust Fan 18” |
| 204 | Supply, installation, testing and commissioning of Air Freshair Line GI Ducting Rs. 1400/- Running Feet Approx Line 20’ Feet |
| 205 | Supply, installation, testing and commissioning of 4 Cylinder Gas Bank Approx Pipe 25’ Feet Extra Work Rs. 1000/- per Running Feet Manifalt Pipe Symlesh Pipe Tata Make 1 ½” Pipe NRV United Make Cylinder Flexible Pipe Surkha Type Cylinder Adopter United Make Pipe Line Symlesh Pipe 1\2” Tata Make 15 PSI Control Valve United Make Ball Volte Across Make NCV 3/8x3/8 United Make |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
