Madhyanchal Vidut Vitran Nigam Limited has published Various System Strengthening Works Under The Jurisdiction Of E.E, Eudd-Residency, Lesa Cis-Gomti Lucknow.. Submission Date for this Tender is 27-09-2023. Wall Construction Tenders in lucknow Uttar Pradesh. Bidders can get complete Tender details and download the document.
Sl. No. | Item Description |
1 | Safe carriage, loading-unloading with proper stacking of following materialfrom ESC-Daliganjto Work Site/JE -Dump Store - |
2 | 11KV3X70/185 SQ MM XLPE CABLE |
3 | 11KVEND TERMINATION O/DOOR & I/DOOR 3X70/185 SQ MM |
4 | 11/0.4 KV 400/630 KVA T/F |
5 | LT XLPE Cable 1x400/630/3.5x400 sqmm |
6 | ST Pole 9 Mtr Long |
7 | ABC (3x120+1x95+1x16) sqmm |
8 | Polymeric Pin Insulator |
9 | Fabrication & erection of S/S type double pole for 11KV line on 11 M long ST pole with fixing of necessary clamps & other accessories like 1 no. top channel 100×50 mm,2 no.MS angle 65x65x6mm,danger board, number plate, barbed wire, TPMO set & D.O. fuse set. |
10 | Construction of T/F plinth of size 2x2x1.5 m on a padding 0.25M deep in ground 1:5:10 cement sand and brick ballast on the top of padding brick work Ist class brick of 0.95 mtr height & 0.35 mtr wall will be constructed. Rest wall should be 0.23 mtr thick. brick work in ratio 1:4 cement & cores Sand in the hollow portion the sand should be filled from the ground level up to 15 centimeter below from the top of wall, Cement, sand & brick Ballasts should be filled up to 15 centimeter. Two no. of channel 100x50 in length 1500mm will be grouded.0.35 CM.RCC will be done with cores sand, cement and stone ballast in the ratio of 1:2:4.The t/fs plinth should be plastered on all sides 12mm thick in ratio 1:6 by cement and cores sand. (All the material will be arranged by the contractor .) |
11 | Construction of retaining wall, fabrication & erection of Wire mesh fencing around Transformer and Distribution Pillar Box with retaining wall & 1 no. gate with locking arrangement made of MS Angle iron of size 50x50x6 mm jointed with nuts and bolts. The panel must be supported with MS Flat of size 50x6 mm.Wiremesh of size 10 SWG rectangle type, its painting as per norms of RESSPO.(All the material will be arranged by the contractor at his own cost). |
12 | Construction of massonary type Distribution Pillar box with first class brick ballast cement, coarse sand, local sand, brick ballast and MS Round bar of 10 mm dia including Straight MS Angle 50X50X6X750 mm- (All the material will be arranged by the contractor). |
13 | Supply & fixing of henless fuse unit 500 amp 650 volts |
14 | S/C Cable laying in normal soil by digging of trench 900 mm deep, 500 mm wide including supply of required material as fine sand, 1st class bricks, stone slab. (All the material required for laying will be supplied by the contractor except 11 KV XLPE cable) |
15 | D/C Cable laying in normal soil by digging of trench 900 mm deep, 500 mm wide including supply of required material as fine sand, 1st class bricks, stone slab. (All the material required for laying will be supplied by the contractor except 11 KV XLPE cable) |
16 | Supply & Fixing of CU L-Piece for 400/630 KVA T/F |
17 | Supply & installation of D.O Fuse set |
18 | Hoisting, winding and jumpering of LT cable size 1x400/630/3.5x400 sqmm between LT distribution box/fuse unit & constructed overhead line with proper lugging and clamping |
19 | Stringing, Sagging, winding and jumpering of LT line with AB Cable (3x120+1x95+1x16) conductor as per RESSPO Norms. (AB Cable provided by deptt and balance material like holding clamp,eye hook, suspension clamp and dead end clamp arranged by contractor .) |
20 | Supply of 11 KV RMU (Three way RMU (2LBS + 1CB) as per T.S/ ApprovedMVVNL GTP) |
21 | Hoisting of 11KV XLPE cable/RMU of 3x70/185 sq mm cable |
22 | ChemicalEarthingsystemwithouterpipe diameter50mm,innerStrip40x6,length3000 mm. galvanization up to 200 micro, earthing pipe withcrystallineconductivemixturefilledinside thepipewithanti-corrosion&highconductive alongwith50Kg(As perrequired) ofBFC which should be capable to reducing the soil resistively with good moisture retaining capacity.(Specificationofchemicalearthingand drawing is hereby enclosed). All material shall by supply by the contractor. |
23 | Providing earthing strip size 50x6mm and connecting from earthing pipe/m.s.earting rod to fuse unit/transformer body/ neutral earthing (Earthing rod & earthing strip arranged by contractor). |
24 | Installation of 11/0.4 KV 400/630 KVA T/F (by crane) |
25 | Installation of RMU including grouting & plinthing |
26 | Wiremesh Fencing for RMU |
27 | Removal of connections from the system, safe Loading- carriage unloading of damaged T/F from site to Store Centre Daliganj/ Transformer repair workshop, Aliganj |
28 | 400 KVA Transformer by tractor trolley/Crane) |
29 | Groutingofpoleindepthof1/6thelengthof poleinratio 1:4:8incementsandandbrick balast as per RESPO norms. |
30 | Construction of pole plinth 300mm x 450 mm above ground level in 1:2:4 in cement, coarse sand and stone gritt as per RESPO norms. |
31 | Painting of new erected ST pole with two coat of red oxide paint,PO red paint at top of pole 2 M & balance by two coats of best quality aluminium paint ISI of Burger/Nerolac/Asian mark as per norms. |
32 | Taping of line |
33 | Supply and fixing of Copper Strip of size 1000x50x6 mm |
34 | Fixing of earth rod (2500x20mm) as per norms. For earthing support ofold existing poles of LT lines including 6 SWG GI/Earth wire . (All Materials provided by contractor) |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail