Nuclear Fuel Complex has published Tender For Civil, Ph, Electrical Conducting And Other Allied Works For Construction Of Cisf Barracks At Nfc Kota Township => Limited. Submission Date for this Tender is 03-10-2023. Electrical Maintenance Tenders in kota Rajasthan. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 23-Sep-2023 | Drawings are attached. | Other | 03-10-2023 |
| Sl. No. | Item Description |
| 1 | I.EARTHWORK : |
| 2 | Earth work inover areasby mechanical means (Hydraulic excavator) / manual means/controlled blasting to required profile, level, grade, camber, etc in all soils/strata as mentioned below upto all depths as per drawing and as directed, 1.5 m in width as well as 10 sqm in plan area including dressing of excavated sides and ramming of bottoms and disposal / stacking of excavated materilas and lead within NFC-K township premises and all inherent lifts and filling in layers not exceeding 200mm, watering, consolidation etc. complete all as per specifications, drawing and as directed by Engineer-in-charge. |
| 3 | Softrock (Loose soil)excavation up to 1.5m level |
| 4 | Hard rock ( by chiselling or wedging or rock hammer and cutter or hydraulic splitter or by using machine such as poclain with jack hammer or controlled blasting or by approved chemical method(obtaining permit shall be responsibility of contractor)as directed by EIC including backfilling, dressing and ramming using available/brought from outside soil/crushed rock filling in layers not exceeding 200mm, watering, consolidation etc. complete all as per specifications, drawing and as directed by Engineer-in-charge. |
| 5 | a) Up to 1.5 m from ground level |
| 6 | b) Above 1.5 m to 3.0 m depth from average ground level. |
| 7 | II. CONCRETE (PLAIN AND REINFORCED) : |
| 8 | Plain Cement Concrete (P.C.C) 1:3:6 by insitu mixing using Weigh Batching or RMC using Ordinary Portland Cement(OPC) conforming to IS 269 or Portland PozzolanaCement (PPC) conforming to IS 1489 Part-1 with Minimum Cementitious Content not less than 250 Kg/Cum(M/s. ACC,Ultra Tech, Ambuja, Birla or equivalent make as approved by EIC)with crushed stone sand and graded stone aggregates of 20mm maximum size at all depths/heights below/above plinth level including consolidation, finishing smooth/broom finish as applicable, curing, etc.,but excluding Formwork, complete as specified and directed. |
| 9 | Reinforced Cement Concrete by insitu mixing using Weigh Batching or approved RMC of Grade M - 25 (Minimum Cementitious Content not less than 330 Kg/Cum) up to specified level using using Ordinary Portland Cement(OPC) conforming to IS 269 or Portland PozzolanaCement (PPC) conforming to IS 1489 Part-1 (M/s. M/s. ACC,Ultra Tech, Ambuja, Birla or equivalent make as approved by EIC ) with crushed stone sand and graded stone aggregates of 20mm maximum size including mixing superplasticizer of brand M/s. FOSROC ,SIKA,BASF,CICO in proportion as per Manufacturer"s Specifications, Pumping / Lifting of concrete to the required heights, Concrete laid to properlevel, profile and slope, placing concrete, consolidation, finishing,curing, etc.,but excluding Formwork and reinforcement as specified and directed. |
| 10 | Below FFL |
| 11 | Above FFL |
| 12 | Casting and fixing in position precast reinforced cement concrete covers of required size in RCC M-20 insitu mixing BY WEIGH BATCHER using Ordinary Portland Cement(OPC) conforming to IS 269 or Portland PozzolanaCement (PPC) conforming to IS 1489 Part-1 (M/s. M/s. ACC,Ultra Tech, Ambuja, Birla or equivalent make as approved by EIC ), crushed stone sand , graded stone aggregate of 10 mm maximum size at and at all depths and heights below and above plinth level including mixing superplastizer (M/s. Fosroc, Demach, Huntsman, Pedilite, Sunanda Chemicals, Agro Chemicals, MBT) in proportion as per manufacturer’s specifications including necessary shuttering, providing and fixing cover blocks of required sizes, consolidation finishing as specified, curing, making casting yard and curing tank, stacking carefully at casting yard and transporting to the site of use placing in position as shown in drawings, aligning, leveling, making good all the damaged surfaces etc., complete as directed for covers for storm water drains/trenches with and without holes including formwork but excluding reinforcement. |
| 13 | III.FORM WORK: |
| 14 | Providing centering and shuttering using good quality densified film-faced Plywood of at least 12mm thick approved make conforming to IS 4990including strutting, propping, staging made out of steel frames/H-frames/ Mild Steel (MS) Pipes/Cup and Lock System etc., and removal of the sameas required including chamfers, splays, keys, wedges, nails, bracings, brackets andapplying One (1) coat of shuttering oil (Cemol/Fosroc make/any other ) on all shuttering surfaces coming in contact with concrete,including PVC cover blocks etc., if required, for insitu Reinforced Concrete and in Plain Cement Concrete works etc., complete as specified and directed. NOTE:The Formwork shall be designed and got approved from the Design Section before erection |
| 15 | a) Below and Upto Finish Floor Level |
| 16 | b) Above Finish Floor Level |
| 17 | IV.REINFORCEMENT & STRUCTURAL STEEL |
| 18 | Supply, fabrication and erection of Reinforcement barsfor Reinforced cement concrete items at and at all depths and heights below and above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more conforming to IS 1786of Tata, Vizag steel, Sail, JSW, JSPL make, including transport to site, loading and unloading, making fan hooks of required shape, dowels for bonding masonry, transporting steel to site, decoiling, removing of scales, straightening, cutting, bending, fixing bars with chairs, space bars wherever required, in position with two strings of 18 gauge soft drawn annealed MS binding wire inclusive of its supply etc., complete as specified and as per direction of Engineer- in-Charge. |
| 19 | Supplying, fabricating, erecting and fixing in position, insert plates/ embedded plates/pipes/MS Hollow Tubes of GI in medium quality conforming to relevant BIS codes of required shape and size, welding anchoring legs not less than 12mm dia MS rods, placing in position in concrete while casting, including painting with one coat of approved red oxide zinc chromate primer and two coats of synthetic enamel paint complete as per drawing in line, level and plumb completeas directed. |
| 20 | V.BRICK MASONRY: |
| 21 | (a) The contactor shall get approved the sample of bricks from the Engineer-In-Charge before procurement on large scale and shall maintain the same for the entire work. (b) Necessaryopenings/nitches/cut-outs,wherever required as per drawings and asked for by the Engineer-In-Charge,shall be provided by the contracter without any extra cost. c) One brick wall thickness shall be considered as 230mm and half brick wall as 115mm and lesser wall thickness if any shall be made up to the required dimensions by the contractor in CM 1:4 to proper line , level and plumb without any extra cost to the Department.d)The rate shall include cost of making the brick masonary to all geometrical shapes and sizes without any extra cost to the Department. |
| 22 | Brick masonary in super structure at all floors and locations using solid autoclave aerated concrete bricks/blocks from approved manufactures conforming to IS2185 (part 3) latest edition in CM 1:6 in walls to correct line, level and plumb including racking out joints, curing, scaffolding, etc completye as per specification, drawing and as directed by Engineer in Charge. |
| 23 | Providing solid autoclave areated concrete brick/block work 115mm thick in partition walls,dwarf walls,parapets,under platforms,curtain walls,fins,external boxing etc. at all floors and locations as per drawing,conforming to IS2185 (part 3) latest edition in C.M 1:4 to correct line,level & plumb including sacffolding,racking out joints, curing etc.complete as per specifications drawings & as directed by the Engineer in charge.i) With115mm,wide and 80mm. thickRCC (1:2:4) stiffeners at every one metre heigth including formwork but excluding the cost of steel reinforcement,which shall be paid under relevent item. |
| 24 | VIFLOORING : |
| 25 | GSB: Construction of Granular sub-base by providing HBG material conforming to Grading-ii of MoRTH Table 400-1 including cost, (excluding seigniorage) charges and conveyance of all materials to work site and spreading in uniform layers with motor grader or by approved means, on prepared surface mixing by mix in place method with Rotavator/approved means at OMC and compacting with vibratory roller of 8 to 10 Tons Capacity/approve means to achieve the desired density etc., complete for finished item of work as per MoRTH Specification 401(5th revision and as directed by Engineer-in- Charge. Note: ( Payment will be made based on levels for finished item of work). |
| 26 | Providing & fixing following vitrified tiles of various thickness or as per manufacturer"s specification conforming to IS 15622 for flooring ( thickness as specified by manufacturer) of make Johnson, Somani, Kazariaof required shade, design, colour and pattern laid on 20 mm thick cement mortar 1:4 (1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd.): 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with epoxy grout and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. |
| 27 | a) Double charge Glazed Vitrified (Rustic) Tile Polished finish of Size of tile 600 X 600mm X 8-10 mm thk for Change rooms , Dry and cold stores, Pantry. |
| 28 | b) In skirting laid over 12 mm thick CM 1:3 backing. (600x600mm.) |
| 29 | c) Double charge Glazed Vitrified Tile Polished finish of Size of tile 800 X 800 mm X 8-10 mm thkfor Lobby and Dormitry area. |
| 30 | d) In skirting laid over 12 mm thick CM 1:3 backing.(800x800mm). |
| 31 | e) Glazed Vitrified Tile Matt/Anti-skid/Rustic finish ofSize of tile 600 X 600X 15 mm thk for kichen and dining area.( Thickness to be specified by the manufacturer) |
| 32 | f) In skirting laid over 12 mm thick CM 1:3 backing. (600x600) |
| 33 | Providing and laying non-skidceramic floor tiles of size 600 X 600 mm (Thickness to be specified by the manufacturer ), of Ist quality conforming to IS: 15622, ofJohnson&Johnson/Somany/Regency/Rak ceramics or approved make , in all colours, shades, laid on 20mm thick cement slurry mortar 1:4 (1 Cement : 4crushed stone Sand), jointing with grey cement slurry @ 3.3 Kg/sqm including pointing the joints with epoxy grout and matching pigments etc., complete for toilets. |
| 34 | Providing and fixing Ist quality ceramic glazed wall tiles of size 200x300/300x300/300X600 (Thickness to be specified by the manufacturer), conforming to IS: 15622 to be, of Johnson&Johnson/Somany/Regency/Rak ceramics or approved make, in all colours, shadesof any size as approved by Engineer- in- charge , in dados, over 12mm thick bed of cement mortar 1:3 (1 Cement: 3 Coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 35 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut Granite stone for risers/skirting of required size, approved shade, colour and texture laid over 12 mm thick, 1:3 cement mortar for risersjoints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,polishing to edges to give high gloss finish etc. complete at all levels for stair case & counter wash basin etc. complete as specified and directed. |
| 36 | Providing and fixing 18 mm thick Granite flooring/dado using slabs of gang saw cut, mirror polished, premoulded and prepolished, machine cut for flooring/kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse Msand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish incuding making holes, molding half round/full roundnosing and grooves for antislippery measureetc. complete at all levels as specified and directed. |
| 37 | VII. DOORS AND WINDOWS: |
| 38 | Providing and fixing factory made single extruded WPC ( Wood polymer Composite ) solid door/window/ceosetory windows & other FRAMES / CHOWKHAT of any colour comprising of virgin PVC polymer of K value 58-60 ( Suspension Grade ), calcium carbonate and natural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement screwed with full body threaded star headed SS screws having minimum frame density of 750kg/cum , screw withdrawal strength of 2200N (Face ) & 1100 N ( Edge ) , Modulus of Elasticity 900 N/mm2 and resistance to spread of flame of Class A Category with property of being termite/borer proof, water / moisture proof and fire retardent and fixed in position with M.S hold fast / lugs / SS dash fastners of required dia and length complete as per direction of Engineer in Charge. ( M.S hold fast / lugs or SS dash fastners). Note : For WPC solid door/window frames , minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 39 | a) Frame size 50 x 100 mm. |
| 40 | Providing and fixing factory made single extruded wpc ( Wood polymer Composite ) solid plain flush door shutter of required size & Colour comprising of virgin PVC polymer of K value 58-60 ( Suspension Grade ), calcium carbonate and natural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms )having minimum frame density of 650kg/cum , screw withdrawal strength of 1800N (Face ) & 900 N ( Edge ) , Modulus of Elasticity 900 N/mm2 and resistance to spread of flame of Class A Category with property of being termite/borer proof, water / moisture proof and fire retardent, include providingand fixing with stainless steel butt hinges of required size with neccessary full body threaded star headed counter sunk S.S Screws, for each door complete as directed. For toilet doors all as per direction of engineer in Charge. The doors if required shall be painted with two coats of synthetic enamel paint over one coat of primer complete as specified and directed by EIC. |
| 41 | a) 30 mm thick. |
| 42 | Providing wood work with CP teakwood in frames for doors& cupboards using II class teakwood at all heights above plinth level wrought framed and fixed in position including providing and fixing with suitable size of coach screws wherever required / M.S. hold fasts of size 40 mm x 3 mm and 200 mm long, bent to shape embedded in cement concrete 1:2:4 blocks for door frames, fixed in position with necessary lugs rawl plugs and screws and coach screws, applying one coat of approved wood primer to the exposed surfaces of door frame and two coats of bituminous paint to the surfaces of frames in contact with masonry/concrete, etc., complete as indicated in drawings and as directed. |
| 43 | Providing and fixing in position double/single leaf flush door shutters of solid block board core, 35 mm thick, BWR grade,at all heights above plinth level internally lipped with second class teakwood, 25 mm deep along all edges of shutters bounded with water-proof type phenol formaldehyde synthetic resin, hot pressed, Chemicaly treated andpre-lamination of required design, colourand pattern including providing teak veneer of 0.4mm ( min) on both faces requisite finishproviding and fixing under pressure with approved type adhesive 200 x 150 mm laminated sheet on both sides where mortice lock is fixedincluding providing and fixing 2nd class teak wood rebate at meeting junction of shutters in case of double door shutters, including providing &fixing ISI marked4 nos SS butthinges with SS pinsize 125 x 63 x 1.9 mmwith screws, &fixing hinges supplied under relevant item to shutter and frame and complete generally as shown in drawings and as specified and directed for single door shutter / double door shutters. |
| 44 | a) Single leaf flush door shutter with natural teak vineer of 0.4mm thick on both faces with french polishing with a melamine coat. |
| 45 | Providing and fixing factory made uPVC white colour sliding glazed window/ventillatorscomprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 46 | Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension including glazing of 6mm thick toughened glass of make Modigurad, Saint Gobain. |
| 47 | Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension including glazing complete as specified and directed. |
| 48 | Stick Structural glazing System :Designing , Providing & fixing of 6MM THK SGU colour glass stick glazing suystem including powder coated Aluminium Sections of make Brand Jindal /Hindalco or equivalent mullion and Transom 111 X 58 X 2 mm & 75 X 58 X 2 mm thick with 80 micron Powder Coading or as per design, designed to withstand wind pressure up to 150 Km/hr., Fabrication charges with notched and fixed with galvanised MS brackets (HDG) hot deep.sealing all joints between individual panels with 20mm wide x 4 mm deep Silicone Joints with Silpurf NB of GE Silicones / Dow Corning 995 with backor rod to give air tight curtain wall to the building. Rate including frame work cost and conveyance of all materials, labour charges, scaffoldingetc.Supply and fixing Vision glass SGU 6 MM THK colour/ reflective Saint gobain glass/Gaurdian Glass/ASI/Modigurd including 25% Ventilation Area i.e providing top hung openble window along with all hardwares having heavy duty point lock, handle, SS friction hinges and all other necessary hardware and screw complete as pecified and directed by EIC.The rate shall include cost of filler between he floors to have air tight system. |
| 49 | Supplying and fixing to wooden doors at and at all heights above plinth level approved mortise locks of Godrej /Everite make ormake comprising brass body and all parts including sticking plates made of brass, stainless steel keys in duplicate, a pair of mortice lock handles of approved pattern of Godrej make or itsmake with approved cadmium plated brass screws of appropriate size etc., complete as directed to single/doubleshutters for all doors. |
| 50 | Supplying and fixing to wooden doors etc. and at all heights above plinth level approved anodized extruded aluminium tower bolts conforming to relevant IS specifications (‘Classic’ or its ) with approved cadmium plated brass screws of appropriate size etc., complete as directed. |
| 51 | a) using 250 mm long, 10 mm shoot. |
| 52 | b) using 150 mm long, 10 mm shoot. |
| 53 | c) Baby latch |
| 54 | Supplying and fixing to wooden doors at all heights above plinth level approved SS door Handles 22mm dia & 300 mm longconforming to relevant IS specifications and with ISI marking with approved SS screws of appropriate size etc., complete as directed. |
| 55 | Supplying and fixing to wooden doors approved SS aldrop conforming to relevant IS specifications and with ISI marking classic/ J.S.E. (ECIE) make or anyof size 250 x 19 mm with suitable approved CP brass screws, machine screws or boltsfor securing clamps from inside etc., complete as directed. |
| 56 | Supplying and fixing at and at all heights above plinth level hydraulic door closures of ‘EVERITE’/Godrej make orconfirming to IS 3564 with all fixtures, fittings and approved screws of appropriate size etc., complete as directed.. |
| 57 | Supplying and fixing to doors at and at all heights above plinth level approved best quality SS hanging floor door stoppers with rubber cushion (anodic coating not less than grade AC 10 as per IS 1868))transparent or dyed to required colour and shade, with necessary screws etc., complete for twin rubber stopper. |
| 58 | VIII. PLASTERINGANDPOINTING: |
| 59 | Cement plastering 6 mm thick for ceiling with cement mortar 1:3 (1 cement :3 river sand) finished smooth finish with including hacking of concrete surfaces, preparation of surface, steel/tubular scaffolding, curing, etc., complete as directed. |
| 60 | Cement plastering 15 mm thick for internal walls in cement morar 1:4 {1 cement(M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd.): 4 River Sand (conforming to IS 1542)} fininshed smooth at all height above plinth level over brick walls or concrete surface including making necessary grooves in between junctions or brick masonary and RCC and also other places wherever required over brick walls or concrete surface preparation of surface, steel/tubular scaffolding curing etc., complete as specified and directed. |
| 61 | Cement plastering 20mm thick in Two (2) coats over exterior masonry and concrete surfaces at and at all heights/depths above/below plinth levelwith 12mm thick base coat in Cement Mortar 1:4{1 cement(M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd.): 4 River Sand (conforming to IS 1542)}, 8mm thick finishing coat in Cement Mortar1:3{1 cement(M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd., KCP): 3 River Sand (conforming to IS 1542)}, final rendering including addition of approved integrated waterproofing compound @ 2% by weight of cementor as per manufacturer’s Specifications for the base coatof make M/s. Fosroc/Demech/ Huntsman/ Pidilite/ SIKA Qualcrete / MBT/Sunanda Chemicals, making necessary grooves, bands, drip moulds, etc., as required, double steel/tubular scaffolding wherever necessary,curing, etc., complete as specified and directed. |
| 62 | Providing and applying white cement based putty in two coats withaverage thickness not less than1 mm, of Birla make or any other approved manufacturer, over the plastered wall surface (external/internal) to prepare the surface even and smooth complete. |
| 63 | IX.PAINTING: |
| 64 | Walls and ceiling painting with premium acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.of Asian or equivalent in Pidilite, Johnson & Nicklson, Nerolac, berger brand, manufacture and shade over two coats of approvedprimer at all heights above plinth level including preparing the surfaces, scaffolding and cleaning, etc., complete and as directed. |
| 65 | Painting exterior walls on sand faced plaster with two coats of Alkali & fungal resistance, dirt resistance exterior paint with comprehensive warranty of 5 years of required shade of Makes Asian - Apex Advancedor equivalent in Pidilite, Johnson & Nicklson, Nerolac, berger, of exterior quality haying 100% acrylic, of approved shade including preparing surfaces, external putty of Birla or its approved equivalent wherever required applying one coat of approved primer as per manufacturers specification, applying andfilling cracks or wherever required for external filler, curing, scaffolding, cleaning, etc., complete. Note :- Minimum Usage Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. or as per manufacturer"s specification |
| 66 | X.WATERPROOFING : |
| 67 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. NOTE :- 1)The treatment shall be tested by ponding water for a period of 10 days. If due to location of rain water pipes the average thickness of treatment exceeds 110 mm for easy flow of water the extra brickbat coba will be paid as extra item and the rate for the same to be got approved from the Department before execution 2) The waterproofing treatment is to be guaranteed for bone-dry condition for a period of 10 years in the prescribed proforma. 3) The measurement for payment shall be the entire area of terrace covered by the treatment measured between brick/concrete parapets without plaster and the area of vatas calculated by taking the length of vatas and the height above the finished level of the terrace |
| 68 | Water proof plaster in cement mortar 1:3 ,with waterproofing compound make of ( M/s Fosroc , MBT, Sika, Sunanada Chemicals etc.) @ 2% by weight of cement including scaffolding, curing, hacking of concrete surfaces etc. Complete a) 15 MM thk for underground drains/cable trench etc. |
| 69 | XI.MISCELLANEOUSITEMS : |
| 70 | Providing and fixing stainless steel ( Grade 304) railing of make Jindal Stainless (JSL) made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, |
| 71 | Supplying, lowering, laying, RCC SPUN PIPES of class and internal dia mentioned below conforming to IS:458 with necessary collars, laid to correct grade and levels at and at all depths below plinth level including cutting to lengths, jointing with hemp yarn and cement mortar 1:1, caulking the joints and finishing, curing, etc., complete as specified and directed. |
| 72 | a) 150mm NB NP-2 |
| 73 | b) 300mm NB NP-2 |
| 74 | b) 600mm NB NP-3 |
| 75 | Providing grouting (including tamping) for foundations, structures, equipments, base plates, anchor holes, etc., with non-shrink, free flow grout ofshrinkhomp-30N/Sqmm of M/S A.C.C, Fosroc or equivalent mixed with filler like sand in 1:1, including shuttering wherever necessary at and at all depths and heights below and above plinth level complete as specified and directed. note: Weight of grout used in the work will be measured for payment. However, the rate quoted shall inclusive of all materials. |
| 76 | Providing and fixing110 mm n.b.un-plasticised PVC rain water pipes with necessary PVC clamps and wooden gutties of approved make conforming to IS: 13592 type ‘A’with injection moulded fittings jointing with approved synthetic adhesive seal rings conforming to IS: 5382 embedding the slab junctions leakproof testing complete in line, level and plumb all as directed. |
| 77 | Providing and fixing CI gratings conforming to IS 1729 for rain water pipe entry mouths/filter bed, etc., including chasing making holes in existing masonry concrete surfaces, refilling with cement concrete 1:2:4 reinstating to the original conditions, painting with two coats of bitumastic paint, all in level and line complete as directed and specified for rain water mouths, filter bed. |
| 78 | XII: WATER SUPPLY |
| 79 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (SDR-11) conforming to IS 15778 of Ashirvad/Supreme or approved make, having thermal stability for hot & cold water supply, including all CPVC brass threaded fittings, i/c fixing the pipe on exposed/recessed/underground surfaces to correct line, level, plumb using clamps as directed. This includes removing of existing pipes and fixtures if required, jointing of pipes & fittings with one step CPVC solvent cement, teflon tape,cost of cutting chases wherever required and making good the same with cement concrete/mortar, cutting or making hole or chases inRCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original conditionincluding testing of joints at cerain locations complete as specified and directed concealed/exposed including cutting chases and making good the walls. |
| 80 | a) For the following Nominal Bore (NB) pipe: 20 mm |
| 81 | b) For the following Nominal Bore (NB) pipe: 25 mm |
| 82 | c) For the following Nominal Bore (NB) pipe: 32 mm |
| 83 | d) For the following Nominal Bore (NB) pipe: 40 mm |
| 84 | e) For the following Nominal Bore (NB) pipe: 50 mm |
| 85 | Providing and fixing in position CPVC ball valves of following sizes of Ashirvad/Supreme make confirming to SDR 11 fittings, including jointing material etc, as specified and directed. |
| 86 | a) 20mm nbfor coolers |
| 87 | b) 25 mm n.b. |
| 88 | c) 32 mm n.b. |
| 89 | d) 40 mm n.b. |
| 90 | e) 50 mm n.b. |
| 91 | Providing, fabricating and fixing the following sizes G.I PIPE INSERTS of length not less than 800mm fabricating out of GI pepes confirming to IS 1239, of heavy quality with threaded one side/ two sides suitably protected, including supplying and welding a puddle flange fabricated out of 200mm*200mm plate of 6mm thick and fixing the inserts to watertank walls/slab for inlett,outlet,scour, overfloor connections completed all as directed. |
| 92 | a)Outlet connections of 50mm n.b and above. |
| 93 | b)For scour with a GI screwed socket and plug of size 50mm n.b |
| 94 | c)For inlet and over flow 50mm n.b |
| 95 | Providing, hoisting and installing at required elevation minimum three layered moulded HDPE cylindrical vertical water storage tanks of various capacities of Sintex or Duracon make with suitable SMC cover at top, coated with UV coating, inlcuding the cost of labour for making hole in the stoarge tank for inlet outlet scour and overflow and the required fittings/gaskets, float valve including making necessary supporting sytem complete as specified and directed by EIC. |
| 96 | XIII. DRAINAGE |
| 97 | Providing & laying structured wall UPVC under ground drainage pipes& fittings (SN-8) of Ashirvad/Supreme make for sewer lines of following size conforming to IS:16098 (Part-1)to proper level & grade, jointing including providing coupler with cement solvent / welded joints / as per manufacturer"s requirement, UPVC fittings such as Bendes, Tees & Y, Reducers, Blanking Plugs, Couplers, Adaptors etc, complete as specified and directed |
| 98 | a) 110 mm DN (SN 8kN/m²-SDR34) |
| 99 | b) 160 mm DN (SN 8kN/m²-SDR34) |
| 100 | Supplying and fixing following size GRADE BuPVC UV-Stabilised soil / waste/rain water pipes (conforming to IS 13592) and fittings (conforming to IS 14735)laid in floor & on exposed faces of wall of Ashirvad/Supreme make, including scaffolding, removal of existing pipelines if any, laying the pipe below floor / ground to proper slope and gradient, jointing the pipe with Solvent Cement/Rubber ring gasket, ensuring water-tightness for the pipes laid as per codal provisions, cutting to the required length including short pieces, fittings with & without door, assorted fittings such as plugs, tees, couplers, reducers, cross tees, reducing tees, elbows, bends, cleaning pipe, single & double Y, vent cowl, gaskets, offsets, Tank / WC connectors, cowls, etc, complete as specified and directed. |
| 101 | a) 75 mm n.b. pipes |
| 102 | b) 100 mm n.b. pipes |
| 103 | Construction of rectangular CHAMBERS of internal clear dimension of mentioned below ( internal clear) in 230 mm thick brick masonry in cement mortar 1:6 over a bed of 150 mm thick 1:4:8 cement concrete in foundation, plastering with cement mortar 1:4, 20 mm thick on inside, and all outside exposed surfaces finished with a floating coat of neat cement, 1:2:4 cement concrete for benching in slope 1 in 30 and channel finished with neat cement, brick corbelling at top ifnecessary to provide clear opening and providing and fixing CI cover with frame of light duty single seal pattern weight not less than 33 kgs embedded in cement concrete 1:2:4, providing and fixing PVC encaptualted MS rungs of 20mm square, each at 300 mm centre to centre if depth exceeds 800 mm, painting CI cover and frame and CI steps with two coats of bitumastic paint etc. complete-For depth of chamber not exceeding 900 mm. However minimum depth of chamber not less than 450mm |
| 104 | a) 450x600mm |
| 105 | b) 600x900mm |
| 106 | Extra over above itemfor depths beyond 900 mm of Rectangular chamber including providing and fixing PVC encaptulate MS rungs 200 square, each @ 300 mm C/C, staggered vertically and horizontally etc., as per specifications. |
| 107 | a) 450x600mm |
| 108 | b) 600x900mm |
| 109 | Providing and fixing in position UPVC bottle Gully Trap of Supreme /Ashirvad make of 160 X 110mm sizes including embedding the trap in 1:2:4 cement concrete, construction of brick masonry chamberin 230 mm thick brick masonry in cement mortar 1:4 over cement concrete bed of 1:3:6 of 100 mm thick, embedding the trap, plastering with cement mortar 1:4, 12 mm thick on inside & outside and all exposed surfaces, finished with a floating coat of neat cement, providing and fixing heavy duty C. I.frame and cover of size 300mmX300mm, 40mm thick cement concrete 1:2:4 bed over brickwork, painting the grating frame and cover with 2 coats of approved anticorrosivebitumastic paint, necessary connection with existing line etc., complete as directed. |
| 110 | Providing uPVC Floor Trap/ Multifloor trapof Ashirvad /Supreme make / Nahani Trap of110 x 75 x 50 mm size size conforming to IS 14735 with CP jalli on top, fixing the trap in position and connecting with waste water pipe by cement solvent / as per manufacturer"s recommandation, embedding the trap in cement concrete 1:2:4 to correct level and gradient,closing the side inlets with plugs if required etc. all complete as specified and as directed |
| 111 | Providing and fixing of best quality UPVC P trapconforming to IS 14735 for urinals of size 110mm X 110mm with 50mm water seal of Ashirvad /Supreme make with CP grating on top including necessary 1:2:4 cement concrete for embedding the trap connecting the trap to waste pipe, etc, complete as specified and directed.. |
| 112 | XIV.SANITARY ITEMS : |
| 113 | Providing and fixing coupled EUROPEAN WATER CLOSETof Parryware make/Hindware , in white glazed vitreous, with integral "P" or "S" trap, Solid plastic heavy quality seat with lid of approved make and Colour with C.P.brass hinges, conforming to IS: 2548 (Part I & II), including cutting and making good floor, wall wherever required. |
| 114 | Providing & fixing vitreous China undercounter/Overcounter Wash hand basin consisting following items of work:- i)Providing vitreous china wash basin conforming to IS 2556 ( part - IV ) and placing the wash basin in position as shown in the drawing or as directed. ii) Providing a pair of either cast iron built - in cantilever type brackets weighing not less than 1.5 kg / each to be embedded in grade M 15 cement concrete block of size 100 X 75 X 150 mm or cast iron wall fixing cantilever type brackets weighing not less than 1kg / each with screw holes to be fixed to wall using screws, rawl plugs etc. to support the Wash basin, conforming to IS 775 for Wall hung basin.( For wall hung wash basin) iii) Fixing Vitreous China under / over the counter / semi recessed type Wash Basin and placing it in position over the granite platform as shown in the drawing or as directed including finishing the joints with white cement all complete. ( For under/over counter wash basin ) iv)Cutting holes or chases in wall & reinstating to its original condition, painting all metallic parts with two coats of approved flat oil paint over a coat of primer, finishing the gap with white / matching cement etc.all as per specification and as directed for wall hung basin.. v)Installation and testing the entire assembly to the full satisfaction of Engineer- in- charge. vi)C.P. brass waste of standard pattern, 15 mm n.b. screw down heavy quality C.P. bras stopcock conforming to IS: 781., 32 mm CP brass bottle trap, with extension pieceincluding painting of fittings and brackets, cutting and making good the walls wherever required complete as specified and directed |
| 115 | a) Vitreous Chinasemi pedestal Wall hung Wash Hand Basin, 570x480 mm size of HINDWARE Make Studio model Cat. No:10096& pedestal 11038or equivalent. |
| 116 | Providing and fixing as per IS 2556flat back half stall urinal of sizeof 328x558 mm sizeof Hindware/Jaguar or equivalent for supporting the pan on suitable heavy quality CI wall brackets, 32 mm n.b. heavy quality, approved make CP brass bottle trap with extension piece, fixing with CP brass spreader and suitable heavy quality CP brass waste coupling to urinal basin, CP brass grating, spring based flush valve for operation of water flushing etc., complete as specified and directed. |
| 117 | Providing and fixing Granite Stone slab of approved shade with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. |
| 118 | Providing and fixing in position bevelled plain edged mirror 600 x 450mm made out of best Indian glass of 6 mm thick of approved manufacturer, mounted on plywood sheet/ plain AC sheet of 6 mm thick fixed in position with four number of CP brass screws with detachable CP brass caps, washers, rawl plugs, etc., complete as directed. |
| 119 | Providing & fixing in position following type CP fittings/ Fixtures/Faucets of 15 mm nominal dia. with ISI mark/ approved make including providing & fixing specials, wall flanges and fixing to concealed / exposed pipe line with leak proof threaded joints using tephlon tapes, testing the joints hydraulically to a pressure of 10 kg./ sq.cm, rectifying the leaky joints if any, including cleaning etc. complete all as per specifications. |
| 120 | a) Providing and fixing heavy quality fancy variety C.P. brass screw down BIB TAPS of M/S. Jaguar/Hindware make conforming to IS: 8931 on G.I. lines- size 15 mm. |
| 121 | b) C.P brass 2 Way Bib Cock with wall flange of Jaguar Cat.No. ORM 10041 |
| 122 | c) Proving and fixing in toilets Health faucet of Jaguar Make (ALD-CHR-573) or equivalent with 1 metre long Easy flex tube in chrome finish and wall hook etc., complete as directed. |
| 123 | d) C.P brass Bottle Trap, 30 mm dia. with wall flange of Jaquar cat. No. ALD 769. |
| 124 | e) C.P brass single lever basin mixer of "Jaquar" cat. No. ORM-10011B. |
| 125 | f) CP brass over head Shower 120 mm dia, multi function with cascade effect & wall flange of Jaquar Cat. No. OHS 1779 |
| 126 | g) Sink Cock with Extended Swinging Spout (Wall Mounted Model)with Wall Flange Jaguar cat. FLR-5347ND |
| 127 | h) Providing Wall Mixer with Provision for Overhead Shower with 115mm long Bend Pipe on Upper Side, Connecting Legs & Wall Flanges of Jaquar product code FLR-CHR-5273UPR complete as specified and directed |
| 128 | i) Regular Body Concealed Stop cock with protection cap suitable for 15/20 mm pipe line of Jaquar cat. No. ALD-083 and exposed part kit with fitting sleeve, operating lever & adjustable wall flange with seal of Jaquar cat. No. ORM-10083K. |
| 129 | j) CP brass Shower Arm straight with wall flange of Jaquar Cat. No. SHA 49483. |
| 130 | k) CP brass waste coupling32 mm sizewith 80 mm height as per Jaquar cat. No. ALD-705/709for wash basin |
| 131 | Supplying following C.P Brass Bathroom / toilet accessories of following make and fixing on the wall using CP brass screws, rawl plugs etc. as per manufacturer"s requirement all complete at the locations shown and as directed by the E-in-C. |
| 132 | a) Stainless steel Toilet Paper Roll Holder, recessed type with flap of Jaguar Cat. No.AHS - 1553 |
| 133 | b) Stainless steel Soap dish, recessed type of Jaquar Cat. No. AHS -1531. |
| 134 | c) Stainless steel Towel Rail/Grab bar of Jaquar Cat. No. AHS-1507. |
| 135 | d) CP brass double Coat Hook of Jaguar Cat. No. AKP-35761P. |
| 136 | e) Liquid soap dispenser Jaquar CAN 1135N |
| 137 | f) Glass shelf 600 mm long as per Jaquar cat. No: ACN-1171N |
| 138 | g) Towel Ring square with round flange of Jaquar Cat. No. CAN 1121N |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
