Tender For Glowing Arm Signal Pole SIGNAL POLE 6 Meter Supplying and erecting the pole of 6.0 meter height of Square Hollow Section (SS) having an aesthetic and pleasing appearance and shall have proven design conforming relevant indan and International standards, to give specified performance, and service Pole Structuen shall be made of 150mm X 150mm square hollow sections (SHS) as per 15 4923 with minumum Yield Strength of 210 MPa (YST 210 Grade or higher) Welding procedure should fotow relevant standards and should be tested for any defects. The mast shall be provided with fully penetraind flange, which shall be free from any lamination or incursion. For the protection of the Pole from Environmental factors like Erosion and Corrosion, entire Pole shall be Hot Dip Galvanised HGD), internally and externally as per ASTMA 123. Galvanizing shall be without any lead content Welding after HDG is not allowed Structural stability of should be ensured and Design code should comply to Wind & Pressure Loading Calculation as per 15 875 (Part 3), Load Combinations 15.800- 2007 & Pole Design as per AASHTO 2015 LRFD Specifications for Structural Supports for Highway Signs, Luminaires and Traffic Signals ASCE/SET 48-11 Design of Steel Transmission Pole Structures For Stability of 4 Meter and 2 Meter arm, support of 40mm x 5mm thick GI Strip should be provided in suitable length Structural Stability report along with Design validation should be provided by registered Structural Chartered Engineer. Base Plates, Baffle Plates and Flanges should be of Adequate design as per IS 875 and 15 800, and should be made of Special Plate Steel as per BSEN 10025 of Grade S355 or Higher Slots of appropriate design should be provided for Anchor bolts for Mounting Pole Flange plate for mounting Arm should be provided with holes as per design requirement. Design for Base Plates, Anchor Bolts and Nut Bolts for Arm should be certified by registered Structural Chartered Engineer Arm Mounting Bolts should be properly covered to Avoid corrosion. Additional Height of Min. 400mm above 6 meter, should be provided for mounting of Digital Advertising Arrangements. Front and Rear Side of cover plate of arm should have arrangement and display Governing Authority Logo/Emblem. Door opening for Pole Electrical connections like Wines, MCBs or Fuse should be provided in such a way that door should provide easy access, easy replacement of components: Door opening should be gap free to avoid intrusion of insects, it should be weatherproof, vandal resistant, having locking arrangement. Cutting made in shaft should not affect structural stability of Pole. Pole should be provided with mounting arrangement for Signal Lights, timers and LED Batten. Cutout with aesthetic design should be made in Pole shaft for housing LED batten. Profile Laser Cutting should be used to ensure precise fitting of LED Batten and Aesthetic looks. Shaft length should be provided with LED lighting in Red, Green and Amber for the length of 1.2m flush mounted LED batten to suit 6 meter pole. LED baten should use LED modules of make Osram Cree/SecEdison or Semicom Led modules should have life of 50,000 hours with lumen efficiency and brightness of 120 lumens per watt LED arm light should comply with IS16104, 16106, 16108, 510322, IES LM79. LED arm lighting should be P66 rated All the LED lights provided on arm should be synchronized with respective signal light (Red, amber green) and timer LED lights on arm should be covered by milky white polycarbonate diffuser to make environment proof and vandal proof assembly Signal Vision System Batten should be made of aluminum extrusion (75 X 35 mm) with LED Light in synchronization with existing signalling Am Pole 4 Meter Supplying and erecting the signal arm shall be made from Rectangular Holo sections (HHS) of 150mm x 100mm as per 15 4023 with minimum Yield Strength of 210 MP ST 210 Grade or higher). The signal arm shall have Am lengths with rectangular cross section mounted at suitable height. It shall be sulable to carry designed number of signal ages which shall be d and flush mounted on the arm through damps and screwshots at desired pusdon Signal arm shall be perpendicular to pols shat Arm should be provided with supporting arrangement for safety and siabety For the protection of the am from Environmental factors ske Emsion and Corrosion, enti arm shall be Hot Dip Galvanised HD tematy and externally as per ASTM A 123 Galvanizing shall be without any lead content Welding after HOG a nit aluwes Structural stlty of shut be ensured and Design code sheild comply to Wind & Pressure Loading Calculation as per 51175 (Part 3), Load Caminatan 5A00-2007 A Pale Design an per AASHTO 2015 LRFD Specifications for Structural Supports for Highway Signs Luminars and Traffic ga ASCE:SE 48-11 Design of Steel Transmission Poe Strucks Structural Stativy mport along with Design vaidation should be provided by regatered Suctural Chartered Engineer Pole ame should be suitable for Tostang CCTV Mount P5 System otc Arm shout be pronded wit mounting arrangement for Signal Lights and LED flates Cutout with aesthetic design should be made in Pole shaft for housing LED batten. Free Laser Cutting should be used to ensure pro ng of LED Batten and Aesthiere looks. Am ngh should be provided witCLED syning in HEO Green and Amber for the length of 3m (tm X 3 ballen) Bush mounted LED batten in sumam Anti-glare cover should be provided for better visbally under Sunshine LED ballen should use LED modules of make Ouam Cree/Seoit dison or Semcoe LED modules shoid have Me of 50.000 hours with lumen efficiency and bingheness of 120 lumens per wan LED anm light should comply with 1516104, 16100 10100, 10322, SLM LED am ghting should be 106 rated Al LED lights provided on arm should be synchronized with respective signal light (fied amber, green and Sme LED lights warm should be covered by milky whine polycarbonate diffuser to make on proof and vandal pronf assembly Signal Vision Sistem Bamen should be made of uminium extrusion (75 X 35 mm) with LED Light in synchronization with messing signaling arm 2 Meler Length Supplying and orecting the signal arm thail be made hom Rectangular How sections (RHS) of 150mm x 100min as per 5 4923 with minimum Yield Strength of 210 MPa (YST 210 Grade or higher). The signal arm shall have din lengths with rectangular cross section moured at stable height it shall be suitable in any designed number of signal lights which shall be fed and founded on the arm through clamps and screwsbolts at deseed position Signal arm shall be perpendicular to pole shaft Arm should be provided with supporting arrangement for salery and atability. For the protection of the arm from Environmental factors ke Eresion and Conosion, entre arm shat be Hot Dip Galvanised (HGD), internally and externally as per ASTMA 123 Galvanizing shall be without any lead content. Welding after HDG is not allowed Structural stability of should be ensured and Design code should comply to Wed & Pressure Loading Calculation as per 18 875 (Part 3), Land Combinations 15 800- 2007 & Pale Design as per AASHTO 2015 LRFD Spoofications for Structural Supports for Highway Signs Luminaires and Traffic Signa ASCE:SEI 45-11 Desgn of Steel Transmission Pole Structures Structural Stability repon along with Design valication should be provided by registered Structural Chartered Engineer Poin arm should be suitable for Sustaining CCTV Mounting PS System ek Arm should be provided with mounting arrangement for Signal Lights and LED Batten Cutout with aesthetic design should be made in Pole shaft for housing LED batten, Protle Laser Cuting should be used to ensure precisa fing of LED Bater and Aesthetic looks Arm length should be provided with LED lighting in RED Green and Amber for the longth of 1 meter of lush mounted LED batton to aut 2 meter arm Ank glare cover should be provided for better visibility under Sunshine LED batten should use LED modules of make Osram CreefSeol Edison or Semicom LED modules should have lite of 50,000 hours with lumen efficency and brightness of 120 lumens per watt LED arm light should comply with 1510104, 16106, 18100, 1510022 IES LM79 LED arm ighing should be IP66 rated All the LED Sights provided on arm should be synchronized with respective signat light (Red, amber, green) and timer. LED lights on arm should be covered by milky while polycarborale diffuser to me environment proof and vandal proof assembly Sional Vision System Batten should be made of aluminium extrusion (75 X 35 mm) with LED Light in synchronization with existing signalling.
