Supplying, Installation And Commissioning Of Furniture At Auditorium Of Computer Science Building And Vlsi Lab Under Rusa 2.0 Fund In Rajabazar Sc. College Campus, University Of Calcutta. , Thetable Size Should Be1200width Mmx 750Depth Mmx 728 Height Mm. Top Should Be 18 Mm Thick Pre Laminated Particle Board All Work Surface Edges Should Be Duly Sealed With 2 Mm Thick Pvc Edgebanding. Understructure Modesty Panel Should Be 18 Mm Thick Pre Laminated Particle Board . The Rectangular Frame Should Be Fabricated Component In 1.2 Mm Thick Crca , Finish : Powder Coat( Epoxy Polyster) . Leg Should Be Fabricated Component In 38 Mm X 25 Mm 1.2 Mm Thick Ms Erw Atube ,Finish Powder Coat ( Epoxy Polyster).The Plastic Cap For Cable Travel Should Be Injection Moulded Polypropylene And Leveler Glide Should Be Nylon 6 & Ms Bolt. The Storage Should Have Shell And Drawer Tray 0.6 Mm Thick Crca Finish Powder Coat (Epoxy Polyster) Plus The Drawer Front Should Be 0.8Mm Thick Crca Finish Powder Coat (Epoxy Polyster) Plus Lock With 10 Lever And Handle And Leveller. The Wire Management Should Be Horizontal Wire Carrier 0.7 Mm Thick Crca Finish Powder Coat (Epoxy Polyster)And Vertical Wire Carrier 0.8 Mm Thick Crca Finish Powder Coat (Epoxy Polyster) . The Product Isul Greenguard, Indoor Advantage Gold, Griha & Svagriha Certified. The Metal Parts To Be Pre Treated With 6 Steps Of Degreasing, Water Rinse, Phosphating And Passivation And The Powder Coating To Be Done Following 9 Tank Spray Phosphating System Followed By Oven Drying At 140º C Emt After Pretreatment Camel Hump Oven For Baking Powder At 180º C And In-Built Cooling Loop After Oven Baking. The Manufactures Should Have In House Quality Checking, Steel Processingand Powder Coating Unit. The Manufacturer Should Have International Member Certificate Of Bifma ,Aiota ,Griha,Iso 9001:2015, Iso 14001:2015, Iso 50001:2011, Iso 45001:2018 Is Mandatory.All The Iso Certificates Should Be Obtained From Nabcb ( Central Govt) Accredited Organization Otherwise Certificates Will Not Be Accepted. Manufacturer Should Have Green Guard Certification(Ul), Greenguard Gold, Greenpro, Bifma Level, Scs Iaq. For Some Of Its Products.The Bidder Should Have Authorised Service Center In District.Bidder/Oem Must Provide Escalation Matrix Of Telephone Numbers For Service Support. Bidder/Oem Must Have Dedicated/Toll Free Telephone No. For Service Support.The Bidder Or Their Oem Should Not Be Black Listed From Any Govt. Establishment In Last 15 Years.The Bidder Has To Submit Bid Specific Authorisation Certificate From The Oem. , The Seat & Back Should Be Made Up Of 1.2 +- 0.1 Cm Thk Hot Pressed Plywood Measured As Per Aq Method Described In Ocp-Qlta-Pl 14-18, Upholstered With Fabric & Moulded Pu Foam With Pvc Lipping All Around. The Back Foam Is Designed With Countered Lumbour Support For Extra Comfort To Popiliteal Area. It Is Moulded High Resilence Polyurethane Foam Of Density =45+/- 2 Kg/M3 And Hardness Load16+-2 As Per Is:7888 For 25% Compression.The Seat Cover Is Injection Moulded In Black Co-Polymer Pp. The Mechanism Is Designed With The Following Features:- 360 Deg Revolving Type. 17 Deg +-2 Deg Max Tilt On Pivot On Center. Upright Position Locking. Tilt Tension Adjustment. The Tabular Frame Is Cantilever Type & Made Up Of Dia 2.54 +-0.03Cm X 0.2+-0.016Cm Thk Ms Erw Tube & Black Powder Coated (Dft 40-60 Microns).It Has To Be An Adjustable Stroke Of 12.0+-0.3Cm. The Bellow Is 3 Piece Telescopic Type & Injection Moulded In Black Polypropylene.It Is Injection Moulded In Black 33%Glass Filled Nylon-66& Fitted With 5 Nos. Twin Wheel Castors.The Pedestal Is Of Dia66.3+-0.5Cm . Pitch Center Dia. (76.3+-1.0Cm. With Castors).The Twin Wheelshould Be Injected Moulded In Black Nylon. The Product Should Be Indoor Advantage Gold, Griha, Greenpro, Scs Iaq Certified. The Metal Parts To Be Pre Treated With 6 Steps Of Degreasing, Water Rinse, Phosphating And Passivation And The Powder Coating To Be Done Following 9 Tank Spray Phosphating System Followed By Oven Drying At 140º C Emt After Pretreatment Camel Hump Oven For Baking Powder At 180º C And In-Built Cooling Loop After Oven Baking. The Manufactures Should Have In House Quality Checking, Steel Processingand Powder Coating Unit. The Manufacturer Should Have International Member Certificate Of Bifma ,Aiota ,Griha,Iso 9001:2015, Iso 14001:2015, Iso 50001:2011, Iso 45001:2018 Is Mandatory.All The Iso Certificates Should Be Obtained From Nabcb ( Central Govt) Accredited Organization Otherwise Certificates Will Not Be Accepted. Manufacturer Should Have Green Guard Certification(Ul), Greenguard Gold, Greenpro, Bifma Level, Scs Iaq. For Some Of Its Products.The Bidder Should Have Authorised Service Center In District.Bidder/Oem Must Provide Escalation Matrix Of Telephone Numbers For Service Support. Bidder/Oem Must Have Dedicated/Toll Free Telephone No. For Service Support.The Bidder Or Their Oem Should Not Be Black Listed From Any Govt. Establishment In Last 15 Years.The Bidder Has To Submit Bid Specific Authorisation Certificate From The Oem. , Supply And Fixing Of Lecture Hall Furniture Should Have Worktops Made Of 25 Mm Thick Pre-Laminated Board Of E1-P2 Grade And Approved Shade Conforming To Is: 12823:1990. All The Edge Of Worktops Should Be Provided With Machine Pressed 2Mm Thick Pvc Edge Band Glued With Hot Melt Glue. The Modesty Should Be Made Of 25Mm Thick Pre-Laminated Twin Board Of E1 -P2 Grade Conforming To Is:12823: 1990 Of Approved Shade. All The Edge Of Modesty Should Be Provided With Machine Pressed 2 Mm Thick Pvc Edge Band Glue With Hot Melt Glue. The Legs Should Be Made Of Ms Erw Oblong Tube (Ls7138) Of Size 75X25x2 Mm Thick With 5 Mm Thk Hr Brackets As Per Is:2062 And 2Mm Thk Crca Brackets As Per Is-5 L 3Welded On To The Tubes. Assembly Should Be Epoxy Polyester Powder Coated (Min 40 Micron). Sturdy Grouting To Floor Through 8Mm Thk Hr Steel (Is 2062) Base Plate Using Anchor Bolts. Shoe Should Be Made Of Ultramid - Nylon Should Be Provided At The Bottom For Covering The Base Plate. The Swiveling Arms Should Be Made Of Ms Erw Tube (Is7 13S) Of Size 50X30x1.6Mm Thk. Oblong Tube With One End Welded With F 55X4mm Thk. Ms Erw Tube (Is7138) And At Another End Should Be Welded With F 48X3.2Rnm Thk. Ms Erw Tube (Is 7138). The Swiveling Arms Should Have Epoxy Polyester Powder Coated (Min 40 Microns). The Swive1ing Arms Should Be Held With Powder Coated Aluminum Die Cast Piece With Swiveling Mechanism Consist Of Ni-Cr Plated Shaft (Is:9550), Torsion Spring Should Be Made Of Spring Steel (Is4454) And Bush Should Be Made Of Nylon (Pa6-Gf30). The Chair Back Should Be Made Of Blow Molded High-Density Polyethylene And Should Be Fixed On The Understructure Assembly With The Help Of Stainless-Steel Pop Rivets. The Chair Seat Should Be Made Of Blow Molded High-Density Polyethylene And Should Be Fixed On The Understructure Assembly. The Seat Support Frame Should Have Side Metal Frames Made From Mild Steel Erw Oblong Tubes 40X20x2mm Thk (Approx. 14 Swg) As Per Is:7138, Seat Support Bracket Should Be Made Of 3Mm Thk.Hr Sheet (Is 2062), Ms Erw Oblong Tube 35X15x1.6Mm (Is7138) Which Should Be Welded Together. Seat Support Channel Should Be Made Of 1 Mm Thk Mild Steel Sheet (As Per Is:513) Should Be Welded To The Understructure For Fixing Seat. The Welded Structures Should Be Coated With Epoxy Polyester Powder (Min 40 Microns). The Base Plate Mechanism Should Be Designed With The Features Such As 360° Revolving Type And Provision For Upright Height Adjustment. The Pneumatic Height Adjustment Should Be With Auto Return Feature. The Seat Should Be Provided With Height Adjustment Using A Gas Lift With An Adjustment Stroke Of 70.0 ± 0.3Cm. The Gas Lift Also Should Have An Auto Return Feature To Allow The User Free Movement While Being Seated And After Use Guides The Upper Structure To Rotate Back To Its Original Position Enabling All Chairs To Align With The Work Top.The Product Should Be Ul Greenguard, Indoor Advantage Gold Certified,Cii Green Pro Certified.The Metal Parts To Be Pre Treated With 6 Steps Of Degreasing, Water Rinse, Phosphating And Passivation And The Powder Coating To Be Done Following 9 Tank Spray Phosphating System Followed By Oven Drying At 140º C Emt After Pretreatment Camel Hump Oven For Baking Powder At 180º C And In-Built Cooling Loop After Oven Baking. The Manufactures Should Have In House Quality Checking, Steel Processingand Powder Coating Unit. The Manufacturer Should Have International Member Certificate Of Bifma ,Aiota ,Griha,Iso 9001:2015, Iso 14001:2015, Iso 50001:2011, Iso 45001:2018 Is Mandatory.All The Iso Certificates Should Be Obtained From Nabcb ( Central Govt) Accredited Organization Otherwise Certificates Will Not Be Accepted. Manufacturer Should Have Green Guard Certification(Ul), Greenguard Gold, Greenpro, Bifma Level, Scs Iaq. For Some Of Its Products.The Bidder Should Have Authorised Service Center In District.Bidder/Oem Must Provide Escalation Matrix Of Telephone Numbers For Service Support. Bidder/Oem Must Have Dedicated/Toll Free Telephone No. For Service Support.The Bidder Or Their Oem Should Not Be Black Listed From Any Govt. Establishment In Last 15 Years.The Bidder Has To Submit Bid Specific Authorisation Certificate From The Oem.
