Military Engineer Services-MES has published Tender For Special Repair To Dsc Billets, Provision Of False Ceiling And Certain Major Revenue Works At Afs Sulur. Submission Date for this Tender is 03-10-2023. False Celing Tenders in sulur Tamil Nadu. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | SCHEDULE A BOQ |
| 2 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed. |
| 3 | Removing excavated materials to a distance not exc. 50m and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and as directed. |
| 4 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes etc not exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard/dense of soilcomplete all as specified and as directed. |
| 5 | M & Lfilling under floors or in foundations using M Sand including watering and consolidation complete all as specified and as directed. |
| 6 | M&L PCC 1:4:8, type D-2 using 40mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed. |
| 7 | M & L pre-cast cement concrete block masonry with solid blocks, type C-1, PCC 1:3:6 using 20 mm graded stone aggregate, exc. 10 cm in width and setting in mortar 1:4 complete all as specified and as directed. |
| 8 | M&L rendering 10 mm thick onbrick or concrete wall surfaces, in cement mortar1:6 finished even and smooth without using extra cement completeall as specified and directed. |
| 9 | M&L preparation of newly plastered surfaces of wall and applying two coats distemper oil emulsion over a coat of alkali resistant primer and 2mm thick plaster of paris putty complete all as specified and directed. |
| 10 | M&L Rendering 15 mm thick in two layers onbrick or concrete wall surfaces, first coat 10mm thick in cement mortar 1:4 and 2nd coat 5mm thick in cement mortar1:4 mixed with water proofing compound as per manufacturer instructions finished even and smooth without using extra cement complete all as specified and directed. |
| 11 | Note for item No 10 :- Water proofing compound shall be measured and paid separately. |
| 12 | M&L applying three coats of cement based paint including preparation over newly plastered wall surfaces of any description, complete all as specified and as directed. |
| 13 | S&F High strength corrosion resistant TMT steel bars of Grade Fe–500of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and directed. |
| 14 | S&F High strength corrosion resistant,TMT steel bar of grade Fe-500, 5 mm dia and above and up to 10 mm dia cut to length, bent to shape required,including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips in stirrups , spacers and binders etccomplete all as specified and directed. |
| 15 | M & LReinforced cement concrete 1:2:4, type B-0 using 12.5mm graded crushed stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed |
| 16 | M & L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.rough finished flat surfaces of concrete complete all as specified and as directed. |
| 17 | M & LReinforced cement concrete 1:2:4, type B-0 using 12.5mm graded crushed stone aggregate as inslabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likecomplete all as specified and as directed |
| 18 | M&L form work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work: not exceeding 200mm thick (Horizontal or sloping) rough finished flat surfaces of concrete complete all as specified and as directed. |
| 19 | M&L Spreading and levelling the soils in layers not exceeding 25 cm thick each layer including watering and well ramming complete all as specified and directed. |
| 20 | M&L Hardcoreofgaugenotexceeding 63mmofbroken stonesorboulders,deposited,spreadandlevelledin layersnotexceeding 15cmthick,wateredand rammed to a true surface completeall as specified and directed. |
| 21 | M&L100 mm thick PCC (1:4:8) type-D-2 using40 mm graded stone aggregate as in sub base floors for receiving tiles complete all as specified and as directed. |
| 22 | M&L Vitrified Ceramic tiles 10 mm thick, lightshade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over andincluding screed bed or bedding layer, 15 mm thick in Cement Mortar 1:6complete all as specified and as directed. |
| 23 | M&L Vitrified Ceramic tiles 10 mm thick, lightshade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces such as skirting/ dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over andincluding backing coat with 15 mm thick in Cement Mortar 1:6 complete all as specified and as directed. |
| 24 | Note for item No22 & 23 :- (i) Vitrified tiles are classified under group B1a of the international Standard for ceramic tiles ISO: 13006. Tiles shall be hard, dense, impervious and frost resistant. Water absorption of tiles shall be less than 0.5% and flexural strength (Modulus of Rupture) shall be more than 35 N/Sqmm. |
| 25 | (ii) The manufacturer"s test certificate andindividual test certificateof Tilesmust be submitted for approval by the concerned authority prior to installation. |
| 26 | M & L 75mm thick, plain cement concrete (1:3:6), type C-2 (using 40 mm graded mechanically crushed stone aggregates),as in plinth protection/path/hard standing including making joints @ 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement complete all as specified and as directed. |
| 27 | Note for item No 26 :- The concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm. |
| 28 | S&F Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt,welded tubes conforming to IS 1161-1979 grade ST-240 complete all as specified anddirected. |
| 29 | S & F Mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel orflat sections) including distance pieces, cleats, gusset plates, wind ties etc conforming to Fe 410-w (Gde E-250) quality A complete all as specified and directed. |
| 30 | S&F Pre painted Coloured corrugated Galvalume roofing system sheet 0.50 mm thick having Zinc aluminum alloy coating AZ150 shall be as per IS:277/ASTM 1379 150 gsm/ sqm double ribbed trapezoidal profile steel sheetany colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws complete all as specified anddirected. |
| 31 | Note for Item No 30:- (Pre-painted coloured Galvalume roofing) :- |
| 32 | (i) The manufacturer"s test certificate andindividual test certificate for the chemical and mechanical properties of sheet must be submitted for approval by the concerned authority prior to installation. |
| 33 | (ii) The contractor shall ensured that no leakages take place from the roof. The roofing shall be Coloured Galvalume roofing system (olive green colour or as approved by GE) with feed material manufactured from 0.50 mm Totalcoated thickness (TCT), minimum 550 MPa yield strength and shall conform to the physical specifications of IS: 2062 of 2011, coated with hot dip metallic Aluminium / Zinc alloy coating AZ150 as 150 gm/sq.mt total on both sides. |
| 34 | (iii) The painting shall be coloured baked enamel polyesterwith silicon coatingoffilm thickness 25 microns nominal on the exposed face/exterior side and on the reverse side ( interior face) shall be white with 15 microns film thickness, over a coat of 5 micron nominalthickness Primer. |
| 35 | S & F mild steel work as in plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 36 | M&L Preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed. |
| 37 | Note for item No 36 :- (a) All synthetic enamel paint, shall be of 1st quality manufactured by the standard firms of make as specified. |
| 38 | (b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works. |
| 39 | (c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint, will be approved by the GE. |
| 40 | (d)Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. The paint so procured shall be of first quality of any approved make as per list of makes specified. i. Berger Paints (Luxol), ii. Jenson & Nicholson (Brolac), iii. Shalimar Paints(Superlac), iv. Goodlass Nerolac (Nerolac), v. Asian Paints(Apcolite) |
| 41 | (e )Unless otherwise specified the tints of paint shall be as approved by the GE |
| 42 | (f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval. |
| 43 | (g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge. |
| 44 | (h) No hair marks from the brushor clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory. |
| 45 | (e)Unless otherwise specified the tints of paint shall be as approved by the GE |
| 46 | (f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval. |
| 47 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soil all as specified and as directed. |
| 48 | Removing excavated soils to a distance exceeding 1.5 KM but not exceeding 5KM and depositing where directedcomplete all as specified and directed. |
| 49 | M&L False ceiling using GI snap grid size 60x60cm with main runner 38x24,wall angle & cross tee 29x24mm wall angle 24x24mm suspended with 4mm dia GI Wire fixed with steel dash fasteners carrying max load upto 8.1 Kg/Sqcm with 4mm thick designer ceiling board complete all as specified and as directed by Engineer-in-Charge. |
| 50 | Supply and fixing factory made UPVC white colour Three track three panelssliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. andprovided with Clear Glass of Saint Gobain / Modiguard make with thickness of 4mm and stainless steel wire cloth of 0.19mm nominal dia. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. Note: For UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 51 | M&L Second class hard wood plain, solid, straight Chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at jointscomplete all as specified and directed. |
| 52 | Supply and Fixing 30 mm thick factory made flush shutter solid core construction with block board core and plywood face panels, commercial type on both faces complete all as specified and directed. |
| 53 | Supply and fixing 100mm long Butt hinges medium weight cold rolledMild steelcomplete all as specified and as directed. |
| 54 | S&F 150mm extruded aluminum alloy handles, fabricatedtype, anodisedcomplete all as specified and as directed. |
| 55 | Supply and fixing 200 mm long aluminum anodized barrel tower bolt extruded section complete all as specified and as directed. |
| 56 | S&F 300mm long Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminum alloy and fixed complete all as specified and as directed. |
| 57 | M & L 15 mm thick damp proof coursein cement mortar 1:2 to horizontal and vertical surfaces including necessary formwork complete all as specified and as directed |
| 58 | Note for item No 57 :- Water proofing compound shall be measured and paid separately. |
| 59 | Supply only integral water proofing compound |
| 60 | S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails and MS frame shall be covered with heat moulded plain colour PVC"C"channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail.Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitablePVCsheetbeadingand jointed together with solvent cement complete all as specified and directed. |
| 61 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified . |
| 62 | Material and labour forGlazed ceramic coloured tiles 350x250x7mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as dado along with 10mm thick 1:4 backingcoat complete all as specified and directed. |
| 63 | M&LNon - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile of sizeexc 0.11 Sqm but n exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match along with screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) complete all as specified and directed. |
| 64 | Note for item No 62 & 63:- The manufacturer"s test certificate andindividual test certificateof Tilesmust be submitted for approval by the concerned authority prior to installation |
| 65 | M & L cutting chases, pinning in brick walls and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed. |
| 66 | S & F 20 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20°C) UV stablized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, complete to walls, ceilings or in floors etc. all as specified and directed. |
| 67 | S & F 25 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20°C) UV stablized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, complete to walls, ceilings or in floors etc. all as specified and directed. |
| 68 | Note for item No 66& 67:- (a)The unit rate quoted is deemed to include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accessories such as pipe hooks, screws clamps etc |
| 69 | (b)Wall thickness of pipes shall be all as per IS : 15801 |
| 70 | S & F 25mm outer dia of pipes PP-R gate valves (brass insert) as per requirement of sitescomplete all as specified and directed. |
| 71 | M&L75 mm thick PCC (1:4:8) type-D-2 using40 mm graded stone aggregate as in sub base floors for receiving tiles complete all as specified and as directed. |
| 72 | M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including screed bed or bedding layer, 15 mm thick in Cement Mortar 1:6 complete all as specified and as directed. |
| 73 | M & L roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and as directed. |
| 74 | S & F in repair 20 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20°C) UV stablized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, complete to walls, ceilings or in floors etc. all as specified and directed. |
| 75 | S & F in repair 25 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20°C) UV stablized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, complete to walls, ceilings or in floors etc. all as specified and directed. |
| 76 | Note for item No 74& 75:- (a) The unit rate shall be include for taking down existing GI pipe and connections and all fittings as directed. |
| 77 | (b)The unit rate quoted is deemed to include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accessories such as pipe hooks, screws clamps etc |
| 78 | (c)Wall thickness of pipes shall be all as per IS : 15801 |
| 79 | S & F in repair 20mm outer dia of pipes PP-R gate valves (brass insert) as per requirement of sitescomplete all as specified and directed. |
| 80 | S & F in repair 25mm outer dia of pipes PP-R gate valves (brass insert) as per requirement of sitescomplete all as specified and directed. |
| 81 | S & F Vitreous china squatting pan "Orissa" Pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe ) including provision of lime concrete beddingfixed including taking down existing damaged one complete all as specified and as directed. |
| 82 | S & F vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) including taking down existing one complete in all respect all as specified and as directed. |
| 83 | S & F in repairs vitreous china bowl urinal flat back, size of 430 x 370 x 340 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and as directed. |
| 84 | S & F in repairs urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and as directed. |
| 85 | S&F in repair PVC Connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed. |
| 86 | S & F in repairs vitreous china wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets any size, including cutting for and pinning in ends of brackets or erecting stand complete all as specified and as directed. |
| 87 | S & F in repairs brass, chromium plated waste fittings of size 32 mmfor glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed. |
| 88 | S & F in repairs 40mm bore Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm- 45gms/40mm-60 gms) complete all as specified and directed. |
| 89 | S&F pillar taps 15mm bore CP with capstan head screwed down high pressure screwed for iron pipe Cat Part No.QT F2006101, HT F3001101 of CERA orequivalent to /Parryware/Hindware/ Jaguar including taking down existing one complete as directedby Engr-in-charge. |
| 90 | S&F in repair 32 mm low density polyethylene (LDPE) pipes of pressure rating 6kgf/sqcm complete all as specified and as directed. |
| 91 | S&Fin repair Towel rail 24" long for wash basin complete all as specified and as directed. (Make : CAT Part No-F5007103 of CERA series or equivalent make of hindware / parriware |
| 92 | M&L Corner Glass shelf assembly including taking existing one complete complete all as specified and directed. (Make :CAT Part No-F5005102 of CERA series or equivalent make of Parriware /Hindware all as specified and as directed. |
| 93 | S&F PVC Dual flush ceramic colour, low level, 10 litres capacity, star white with inlet float ball valve, PVC flush pipeand handle, making proper fixing and hanging arrangementsIncluding taking down existing one complete all as specified and as directed by Engineer-in-Charge Make:- Cat Part No 21029 ofhindware or equivalent |
| 94 | M&L PVC (SWR) 110mm bore S Trapincluding taking down existing one complete all as specified and as directed. |
| 95 | M&L110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ringjoints fixed to wallincluding taking down existing damaged PVC Rain Water Pipes (any size) along with all fittings heads bends etc complete all as specified and as directed. |
| 96 | M&L 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ringjoints fixed to wallincluding taking down existing PVC Rain Water Pipes (any size) along with all fittings heads bends etc complete all as specified and as directed. |
| 97 | S & F in repairs PVC (SWR) bends any radius 110 mm dia fixed to wallcomplete all as specified. |
| 98 | S & F in repairs PVC (SWR) bends any radius 75 mm dia fixed to wallcomplete all as specified. |
| 99 | S & F in repairs PVC (SWR) 110mm bore junction (single T) equal or unequal provided with access door complete all as specified and as directed. |
| 100 | S & F in repairs PVC (SWR) 75mm bore junction (single T) equal or unequal provided with access door complete all as specified and as directed. |
| 101 | S&F PVC (SWR) 75mm bore junction vent cowlincluding taking down existing one complete all as specified and as directed |
| 102 | M&L PVC (SWR) floor trap 75mm dia of outlet pipe, plain with grating including jointing with solvent cement including taking down existing damaged one complete all as specified and as directed. |
| 103 | M&L PVC (SWR) multi floor trap 75mm dia of outlet pipe, plain with grating including jointing with solvent cement including taking down existing damaged one complete all as specified and as directed. |
| 104 | Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided and removal of debris out of MD land complete all as specified and directed. |
| 105 | Material and labour forGlazed ceramic coloured tiles 350x250x7mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as dado along with 10mm thick 1:4 backingcoat including dismantling of existing tiles and removal of debris complete all as specified and directed. |
| 106 | M&LNon - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile of sizeexc 0.11 Sqm but n exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match along with screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) including dismantling of existing tiles and removal of debris complete all as specified and directed. |
| 107 | Note for item No 105 & 106 :- The manufacturer"s test certificate andindividual test certificateof Tilesmust be submitted for approval by the concerned authority prior to installation |
| 108 | S & FBib Cock with wall flange screwed down screwed for iron pipe 15mm bore CAT Part No Qt F2006152 HT F3001152 of CERA orequivalent to Parryware/Hindware/Jaguar including taking down existing one complete as directedby Engr-in-charge. |
| 109 | S & F in repairs wall mounted Shower Arms 190mm long flat shapefor wall mounted shower with flange complete all as specified and directed. Make :CAT Part No-SHA-483of Jaguar or equivalent make of parriware /hindware. |
| 110 | S & F in repairs overhead Shower ø105mm Round Shape Single Flow with air effect (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning Systemcomplete all as specified and as directed. Make: CAT Part No- OSH-1709 of Jaguar or equivalent make of parriware/ hindware. |
| 111 | S & FAngular stop cock, valves high pressure screwed both ends iron pipe or for unioins 15mm dia, CAT Part No QT F2006201 HT F3001201 of CERA or equivalent to Hindware/Jaguar including taking down existing one complete as directedby Engr-in-charge. |
| 112 | Taking down chowkhat or frame(wooden/steel) not exceeding1.5 Sqm each with shutter (with out taking off shutters from the frame) complete all as specified and as directed. |
| 113 | Supply and fixing 75mm long Butt hinges medium weight cold rolledmild steel, and fixed complete all as specified and as directed. |
| 114 | Supply and fixing in repair 75mm long Butt hinges medium weight cold rolledstainless steel, and fixed complete all as specified and as directed. |
| 115 | S&F 100mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 116 | S&F in repair 100mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 117 | S&F 100mm long Aluminium anodised, barrel tower bolts of extruded section and fixed |
| 118 | S&F in repair 100mm long Aluminium anodised, barrel tower bolts of extruded section and fixed |
| 119 | M&L PCC (1:2:4) Type B-0, using 12.5 mm graded stone aggregate as in coping including necessary form work finished fair and even surface without using extra cement including weathering slightly roundedor chamfered angles and throating complete all as specifiedand as directed |
| 120 | M&L Salt-glazed stoneware drain pipes, 150 mm bore, laid in trenches and jointed as specified, complete including taking down existing damaged pipe,of any size including damaged haunching/ bed concrete etc complete all as specified and as directed. |
| 121 | M&L Plain cement concrete (1:3:6) type C2 (40 mm graded stone aggregate)asconcrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes ofsize 150mm bore of pipe, complete all as specified and as directed. |
| 122 | Dismantling the existing unserviceable gully trap including chamber and material and labour for provision of new salt glazed stoneware gully trap, square or round mouth type "P" of size 180X150mm, including setting and jointing in cement mortar 1:1 in chamber with plain cement concrete base in PCC 1:2:4 type B1 using 20 mm graded stone aggregate, brick work in cement mortar 1:4, rendering in cement mortar 1:4, all around finished even and fair using extra cement, precast cover slab in RCC 1:2:4 type B1 using 20mm graded stone aggregates, reinforcement with 6mm diain both ways etc, including provision of handle etc complete all as specified and as directed. |
| 123 | S&F 5.0 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq.m in each pane complete all as specified and directed. |
| 124 | M&L Rendering 15 mm thick in two layers onbrick or concrete surfaces, first coat 10mm thick in cement mortar1:4 and 2nd coat 5mm thick in cement mortar1:4 finished even and smooth without using extra cement including taking down existing cement plaster and removal of debris complete all as specified and directed. |
| 125 | M&L for preparation of newly plastered surface of wall and applying three coats of white wash complete all as specified and directed. |
| 126 | Taking down Chowkhats or frames exc 1.5 sq. mbut n exc 4 Sqm each but with shutters (without taking off shutters from the frame ) complete all as specified and directed. |
| 127 | Taking down Shutters of any description exc 1 but n exc 2 Sqm complete all as specified and directed. |
| 128 | M & L cutting holes in stone wall exc one brick and n.exc two brick in cement mortar for inserting hold fasts/lugs and making good dismantled portion in cement mortar 1:3 or 1:2:4 type B-1 concrete as required complete all as specified and as directed. |
| 129 | S & F MS work (flat iron) 25mm x 3mm thick) in small articles such as hold fast and similar small articles conforming to Fe 290 Gde E-165 including taking down existing one complete all as directed. |
| 130 | S & F flush shutters,30mm thick, solid core construction, with particle board core and ply wood face panels, commercial type on both sides,complete all as specified and directed. |
| 131 | S & F 30mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) completeall as specified and directed. |
| 132 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples completeall as specified and directed. |
| 133 | S&F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples completeall as specified and directed. |
| 134 | Supply and fixing in repairs 100mm long Butt hinges medium weight cold rolledMild steelcomplete all as specified and as directed. |
| 135 | S&F in repair 150mm extruded aluminum alloy handles, fabricatedtype, anodisedcomplete all as specified and as directed. |
| 136 | Supply and fixing 150 mm long aluminum anodized barrel tower bolt extruded section complete all as specified and as directed. |
| 137 | Supply and fixing in repair 150 mm long aluminum anodized barrel tower bolt extruded section complete all as specified and as directed. |
| 138 | Supply and fixing in repair 150mm aluminium plate II type, gate and shutter, hooks and eyes complete all as specified and as directed. |
| 139 | S&F 25mm dia mild steel powder coated drapery rod out to length required without joint in between and fixed at openings including taking down existing one complete as directedby Engr-in-charge. |
| 140 | S&F Mild steel powder coatedbrackets for holding the drapery rod and fixed to wall with MS screw including taking down existing one complete as directedby Engr-in-charge. |
| 141 | Supply and Fixing in repairs Mild steel powder coated fancy type brackets fixed at both the end of drapery rod of same colour and type of drapery rod as directed. |
| 142 | S&F 300mm long Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminum alloy and fixed complete all as specified and as directed. |
| 143 | S&F in repair 300mm long Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminum alloy and fixed complete all as specified and as directed. |
| 144 | S & F Aluminium powder coated ofthree track sliding window outer frame top & sides (section no-20831) of size 92.0x31.75x1.5mm weighing 1.06 Kg/m, frame bottom (Section No 20832) of size 92.0x31.75x1.5mm weighing 1.248Kg/m , shutter to plain vertical (Section No 21093) of size 39x18x1.5mm weighing 0.634 Kg/m, shutter interlock vertical frame (section 21094) of size 39x18x1.55 weighing 0.734 Kg/m, shutter bottom horizontal frame (Section No 20551) size 40x20x1.5mm weighing 0.484 Kg/m, with powder coating of min thickness 50 micron , sliding type with out sash bars, 4mm thickness colour glass, rubber packing, snap beading screws with stainless steel wire mesh, including taking down existing window with chowkats of any size, complete all as specified and directed |
| 145 | Note for item No 144:- Thickness of the powder coating shall be minimum 50 micron |
| 146 | M & L preparation of new woodensurface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed |
| 147 | Note for item No 146 :- (a) All synthetic enamel paint, shall be of 1st quality manufactured by the standard firms of make as specified. |
| 148 | (b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works. |
| 149 | (c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint, will be approved by the GE. |
| 150 | (d)Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. The paint so procured shall be of first quality of any approved make as per list of makes specified. i. Berger Paints (Luxol), ii. Jenson & Nicholson (Brolac), iii. Shalimar Paints(Superlac), iv. Goodlass Nerolac (Nerolac), v. Asian Paints(Apcolite) |
| 151 | (e )Unless otherwise specified the tints of paint shall be as approved by the GE |
| 152 | (f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval. |
| 153 | (g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge. |
| 154 | (h) No hair marks from the brushor clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory. |
| 155 | (e)Unless otherwise specified the tints of paint shall be as approved by the GE |
| 156 | (f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval. |
| 157 | S&F375mm, ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 158 | S&F in repairs375mm, ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 159 | S&F Floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor overall 140mm complete all as specified and as directed. |
| 160 | S&F Floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor overall 140mm complete including taking down existing one completeall as specified and as directed. |
| 161 | M&L Pre painted Coloured corrugated Galvalume roofing system sheet 0.50 mm thick having Zinc aluminum alloy coating AZ150 shall be as per IS:277/ASTM 1379 150 gsm/ sqm double ribbed trapezoidal profile steel sheetany colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws including dismantling of existing one all complete all asdirected. |
| 162 | M&L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mmthick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws including dismantling of existing one all as directed. |
| 163 | Note for pre-painted coloured Galvalume roofing :- |
| 164 | (i) The manufacturer"s test certificate andindividual test certificate for the chemical and mechanical properties of sheet must be submitted for approval by the concerned authority prior to installation. |
| 165 | (ii) The contractor shall ensure that no leakages take place from the roof. The roofing shall be Coloured Galvalume roofing system (olive green colour or as approved by GE) with feed material manufactured from 0.50 mm Totalcoated thickness (TCT), minimum 550 MPa yield strength and shall conform to the physical specifications of IS: 2062 of 2011, coated with hot dip metallic Aluminium / Zinc alloy coating AZ150 as 150 gm/sq.mt total on both sides complete all as specified and as directed. |
| 166 | (iii) The painting shall be coloured baked enamel polyesterwith silicon coatingoffilm thickness 25 microns nominal on the exposed face/exterior side and on the reverse side ( interior face) shall be white with 15 microns film thickness, over a coat of 5 micron nominalthickness Primer. |
| 167 | (iv) The contractor shall produce purchase vouchers for each lot and independent test for verification of Engineer-in-Charge. |
| 168 | M&Lpoint wiring using approved colour coding as per ISwith PVC insulated, unsheathed FRLS multi stranded copper conductor 1.5 sqmm (nominal area) 1100 volt grade cable for phase & neutral drawn through PVC conduit fixed on surface ofwall, columns etc including PVC insulated, unsheathed FRLS multi stranded copper conductor 1.5 sqmm (nominal area) copper conductor as earth wire and connected to earth dolly complete all as specified and as directed for the followings complete all as specified and directed. |
| 169 | One light point/fan/bell point controlled by one switch |
| 170 | All as per item No. 168 here in before but for one switch socket outlet 3 pin, 5 ampon independent board |
| 171 | All as per item No. 168 here in before but Wiring with 4 Sqmm copper multistranded unsheathed cable and 4 Sqmm copper cable for earth continuity conductor controlled by one switch socket outlet 3 pin 15 Amps on independent board |
| 172 | S & F modular switch1 way 6 amp.1 module complete all as specified and directed. |
| 173 | S & Fmodular switch1 way 16 amp.1 module complete all as specified and directed. |
| 174 | S & F modular Socket, 6A - 2/3 pin combined, 2 module complete all as specified and directed. |
| 175 | S & F Socket, 6A/16A - 2/3 pin combined, 2 module complete all as specified and directed. |
| 176 | S & F modular white cover plate with frame, 3 module complete all as specified and directed. |
| 177 | S & F modular white cover plate with frame, 6 module complete all as specified and directed. |
| 178 | S & F modular Metal flush box, 3 module complete all as specified and directed. |
| 179 | S & Fmodular Metal flush box, 6 module complete all as specified and directed. |
| 180 | S&F electronicmodular fan regulator 230 volts, step type socket type, hum free 120 watt 2 Module complete all as specified and directed. |
| 181 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. |
| 182 | Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 183 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 184 | Supply and fixing 1200 mm sweep ceiling fans with brushless direct current motor (BLDC), five star rated, 230V, Min air delivery 210 CFM with service value 6.00 BEE., complete with blades, down rods and fittings accessories like flexible copper cord if size 1.5 sqmm etc, complete all as specified and directed. |
| 185 | Supply and fix exhaust fan made of sturdy Engineering plastic with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed. |
| 186 | S&F factory madepowder coated distribution board SPN, 8 way double doorincludingbus bar, Neutral bar, standard DIN rail, earth bar complete all as specified and conforming to IS: 8623all as specified. |
| 187 | Supply & fix single pole neutral, MCB 32 amp, 240 v, 50 Hz ACsuitable for ‘C’ curve, 10 KA breaking capacity conforming to IS 8828 of 1996complete all as specified and directed. |
| 188 | Supply & fix single pole MCB 6 to 32 amp, 240 v, 50 Hz ACsuitable for ‘C’ curve, 10 KA breaking capacity conforming to IS 8828 of 1996complete all as specified and directed. |
| 189 | Supply & fixindustrial type metal clad plug top & socket single pole and a neutral link earth enclosure with two pin and earth plug complete with one MCB SP 32 Amp all as specified and directed |
| 190 | Supply and fixing LED street light fitting 35/36 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed. |
| 191 | M&L for sub main wiring with PVC insulated unsheathed FRLS 1100 volts grade multi stranded copper conductor cable2 runs of 4 sqmm drawn through in and including PVC casing and capping of suitable size and all accessories fixed to wall / floors along with 1 run of 4 sqmm PVC insulated unsheathed copper conductor multi stranded cable 1100V grade as earth continuity conductor and connected to common earth dolly complete all as specified and as directed. |
| 192 | Note for Item No 191:- (a)2 runs of 4 sqmm cable along with 1run of 4 sqmm cable for earth conductor and PVC casing and capping shall be measured as one length. |
| 193 | Supply, installing, testing and commissioning of wall mounted split type AC of capacity 1.5 TR, (indoor/outdoor unit complete) with 5 star rating and EER 3.2,inverter technology and cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality complete all as per specified and directed |
| 194 | Supply, installing, testing and commissioning of wall mounted split type AC of capacity 2.0 TR, (indoor/outdoor unit complete) with 4 star rating and EER 3.2,inverter technology and cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality complete all as per specified and directed |
| 195 | Note for Item No 193 & 194:- Copper tube, insulation materials, clamps, out door unit stand and water pipe from condenser unit etc as required shall be arranged by the contractor and cost for the same is deemed to be inclusive in this item. |
| 196 | Supply and fixing and testing of 4 KVA capacity Voltage stablizer for automatic operation, single phase naturally air cooled , copper wound, indoor type & designed for input variation between 170V - 250V with output voltage stabilized at 230 V with accuracy of± 2.5%complete all as per manufacturers instructions and directed by Engineer-in-Charge. |
| 197 | Supply and fixing and testing of 5 KVA capacity Voltage stablizer for automatic operation, single phase naturally air cooled , copper wound, indoor type & designed for input variation between 170V - 250V with output voltage stabilized at 230 V with accuracy of± 2.5%complete all as per manufacturers instructions and directed by Engineer-in-Charge. |
| 198 | S & F Digital 2 AC wall mounting type cyclic timer for automatic change over with two heavy duty 30 Amp relay output capable to take load of AC-1 and AC-2 up to 2 Tons complete with following technical specification as per manufacturers instructions and directed by Engineer-in-Charge. |
| 199 | Note for Item No 198 :- (i) Operating Voltage Range :- 90 V to 440 V AC, 50 Hz |
| 200 | (ii) Maximum contact rating :- 30 A @ Unity PF |
| 201 | (iii) Technology :- Advanced Micro - Controller with Memory Backup |
| 202 | (iv) Mounting :- Wall or board mountable |
| 203 | (v) Display :- 16 Characters x 2 lines Multi- info LCD with Back-light |
| 204 | (vi) Setting :- Simple 3 buttons to set AC-1, AC-2 ON and OFF Times independently |
| 205 | (vii) Modes :- Auto & Manual Modes |
| 206 | (viii) Memory Backup :- Up to 7 Years for the setting done for AC-1 & AC-2 by way of replicable coin cell |
| 207 | Supply, installation, testing and commissioning of high quality standalone integrated full diffuser LED Troffer with a min system lumen of 3600 Lm (+/- 100 Lm tolerance) and system wattage not exceeding 36W (+/-5% tolerance) with an efficiency 100 lumen /watt. CCT of 6500K with SDCM of <5 and CRI >80. The housing should be of high quality CRCA & PS diffuser with PF > 0.95 and THD <= 10% input voltage range of 140-270V. Lifetime of 50000 hours @ L70. Product should be suitable for continuous operation (14-16)hrs per day)m. The LED light Engine (PCB) should be rectangular /square boards and not strip type, should be FR4 with 1mm thickness with more than 300 LEDs symmetrically mounted over it to maintain the optical and thermal stability of the system over the life time. the sensor should be a motion detector and should be a connected with a digital interface to the led driver and it can be converted to a standard luminaire if this interface is not connected.(plug and play device) The time delay in the sensor should be min 15 (+5) mins. The coverage of the sensor should be 1.5m radius when installed in height of 8 ft. the luminaire should be class B serviceability (Driver needs to be separate and can be changed at site. The same family of luminairy should be available in the both the version high Lumen (3600 Lm) and Low lumen (2800 Lm) . The LED used in the luminaire shall be only of LG innotech, Lumileds APT Electronics , Nichia and CREE & no other make. The driver should have min of 3KV surge/burst protection. Standby mode power of the system should be less than 1 watt avg when the occupancy sensor has turned off the luminaire. Driver should be protected for open circuit & short circuit protection for LED side complete all as specified and directed by Engr-in-Charge. Make :Philips RC 383B LED 36S-6500 PSU OD WH PIR or similar in OSRAM/GE. |
| 208 | S & F CRCA housing of size 2"x2" suitable for mounting the LED light on ceiling with all accessories and fittings complete all as specified and directed. |
| 209 | S&Ffactory madepowder coated distribution board SP & N 8 way single door,includingbus bar, Neutral bar, standard DIN rail, earth bar complete all as specified and conforming to IS: 8623complete all as specified and directed. |
| 210 | S & F XLPEinsulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable heavy duty with aluminium conductor 1100Volts grade cross sectional area 25 Sqmm 4 core drawn through ducts/fixed to wall/pole/ inside panel/ drawn through pipe including cable glands and terminal sockets including complete all as specified and directed. |
| 211 | S & F MCCB, 4 Pole, 63 Amps, thermal magnetic release adjustable type, 415 Volt, 16 KA including Triple pole neutral, 4 way, single door sheet metal enclosure connecting up to using suitable size of copper lugs complete all as specified and as directed. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
