Tender For Construction Of Rangmanch Hall Sojat City
Tender Value
11.30 Crore
Estimated cost
Bid Submission
03 Oct 2023
0 days left
EMD
22.60 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
sojat → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Rangmanch Hall Sojat City
BOQ
| Sl. No. | Item Description |
| 1 | Excavtion |
| 2 | Earth work in excavation in open area, STP, WTP, Pumping station with mechanical means including dressing of sides and ramming of bottoms, including getting out the excavated material, disposal of excavated material lead upto 1000m at suitable site as per as per drawing and as per direction of Engineer. (Measurements for payment to be done as per standard drawings).4.9.2.1 Upto 3.0 m depth Oridinary Rock |
| 3 | Hard Rock (Blasting Prohibited) Upto 3.0 m depth |
| 4 | Providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering =All up to plinth leve 1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 5 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. Thermo-Mechanically Treated bars. |
| 6 | Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete. |
| 7 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 8 | Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 9 | Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands , coping, bed plates, anchor blocks, sills, chhajjas lintel, beam etc. |
| 10 | Centering and shuttering with plywood or steel sheets including strutting, propping, bracing both ways with wooden members andremoval of formwork for superstructure up to 4.5 mtr aboveplinth,for: Add extra over item Nos. 4.12.to 4.12.11 for doing centering and shuttering work for each subsequent storey. For Additional Height upto Ist Floor |
| 11 | Add extra over item Nos. 4.12.to 4.12.11 for doing centering and shuttering work for each subsequent storey. For Additional Height upto IIst Floor |
| 12 | Providing and laying in position specified grade of reinforced cement concrete including curing compaction finishing with rendering in cement sand mortar 1:3 (1-Cement:3-coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement.All work up to plinth level : 1:1:2 (1-Cement:1-Coarse sand:2-graded stone aggregate 20 mm nominal size). (As per design mix) |
| 13 | Providing and laying in position specified grade of reinforced cement concrete including curing compaction finishing with rendering in cement sand mortar 1:3 (1-Cement:3-coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement.All work up to plinth level : 1:1.5:3 (1-Cement:1.5 coarse sand:3-graded stone aggregate 20 mm nominal size) |
| 14 | Random Rubble stone masonary for foundation and plinth in Cement Sand Mortar above 30 Cm. thick wall in : Cement Mortar 1:6 (1-Cement:6-Sand). |
| 15 | Earth filling with available surplus soil excavated from foundations and taken only from outside of building plinth in layers not exceeding 20cm in depth, consolidating each deposited layeincluding ramming and watering and consolidation with lead up to 50 m and lift upto 1.5 m. |
| 16 | Supplying and stacking good earth at site of work. Note: 1) Loading, unloading and carriage to be paid extra as per actual lead.2) Earth measured in stacks will be reduced by 20% foe payment |
| 17 | Random rubble stone masonry work in cement mortar with mechanical mixer in foundation (at any level) complete as per drawing and technical specification and as per clause 1000 and 1400 of MoRT&H specification including all scaffolding material, labour, machinery but excluding pointing and plastering. In cement mortar 1:4 (1 cement : 4 coarse sand) |
| 18 | Extra for subsequent storey or height of 4.5 Mtr. or part thereof for all masonary work. |
| 19 | Course rubble facing First Sort. |
| 20 | Course rubble facing Second Sort. |
| 21 | Stone work (machine cut edges) for wall lining etc. (veneer work) backing filled with a grout of 12mm thick cement mortar 1:3 (1cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing by means of cramps which shall be paid for separately) : White sand stone - exposed face fine dressed with rough backing .26.1.3.1 70 mm thick. |
| 22 | Supplying and fixing stone liri in CM 1:4 work facing with proper projection and chiesel dressing of edges of stone two line dressing of building corners, jambs etc. including uniform joints using aluminium square section of size 12 mm to 15 mm as per requirement of course and width of stone not less than 12 Cm., with requisite humber headers (minimum length of stone 0.9 M) 14 cm (5.5\")thick. |
| 23 | Supplying and fixing machine cut fine dressed Red/Pink sand stone dasa or coping, with full moulding if required laid on cement mortar 1:4 including pointing with admixture of pigment matching with the stone shade. (a) White Ashlar (Use as Elevation Kadau) 75 mm thick |
| 24 | Half brick masonry with FPS brick of class designation 75 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) |
| 25 | Brick work with FPS bricks of class designation 75 in superstructure above plinth level upto two stories in all shapes and sizes in : 24.6 Extra for brick work in superstructure above two stories for each two stories or part thereof by mechanical means by lifting material using mobile crane . 24.5.2 Cement mortar 1:6 (1 cement : 6 coarse sand |
| 26 | Providing and fixing of precast concrete interlocking tiles of desired shape of M 30 grade manufactured from fully computerized automatic stationery hydraulic vibrio pressed machine and fully computerized automatic batching plant of class A1/A2 as per BS 6717:2001. The CC interlocking paving blocks be laid on average50mm. thick bed of coarse sand and the joint is to be filled with fine sand. Laying procedure on compacted sub-base as defined. Complete job is to be executed as per the instruction of Engineer incharge. The rates to be inclusive of all lead & Lifts etc. complete as per specifications. Tensile splitting strength, abrasion and braking load etc. as per BS 6717:2001, Grey cement. 9.10.2 80mm thick |
| 27 | Providing and fixing Marble stone flooring table rubbed, 15-18 mm thick over 20mm (Av.) thick base of CM 1:4 (1 cement : 4 coarse sand) or slab in wall, steps, pillars, counters, jambs, shelves, sills etc laid over 12mm (Av.) thick base of CM 1:3 (1 cement : 3 coarse sand), jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete Makrana \"Adanga\". Upto to 1500 Cm2 Tiles |
| 28 | Providing and fixing Granite stone slab mirror polished and machineedge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slabincluding grinding, rubbing and polishing complete. Jhunjhunu / Jalore (Red / Choclate Colour) Upto to 1500 Cm2 Tiles |
| 29 | Providing and fixing 1st quality MAT finished ceramic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). |
| 30 | Ceramic glazed vitrified tiles of colour standard white, grey, ivory, fume, red brown, light green, light blue, and other light shades 1st quality Size 600mm x 600mm |
| 31 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade using 50% white cement 50% Grey cement. |
| 32 | Construction of stone masonry cylindrical road side inspection chamber of 450mm dia (internal) with 300mm thick wall of stone masonry in cement mortar 1:4 (1 cement : 4 coarse sand), filling of Jhiri, 20mm thick inside and outside plastering with CM (1:3), inside plaster finished with neat coat of cement, with cast in situ PCC M10 grade foundation of 1150 mm dia and 100 mm thickness,, 75mm thick PCC M15 flooring, precast SFRC/RCC circular 450mm dia MD manhole frame and cover (as per IS 12592 amended upto date) embedded in 200mm thick PCC M20 grade concrete, includingproviding and fixing 2 Nos 110mm OD, 0.5m long PVC-U pipe pieces of stiffness class SN 8 as per IS 15328 and plugging the same, testing for water tightness etc. complete as per approved drawing and/or directed by Engineer. Note: Excavation of earth work and road cutting will be measured and paid separately SM Road side inspection chamber of 450mm depth |
| 33 | Plaster on new surface on wall in cement sand mortar 1:3 including racking of joints etc. complete fine finish : 25 mm thick. |
| 34 | Polyethylene water storage tank with cover and suitable locking arrangement 1000 litres capacity. |
| 35 | 2000 litres capacity. |
| 36 | Earth work for Sewer line and Manhole in excavation in foundation, trenches manholes, road side chambers etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level including allowances for any additional excavation beyond the drawings (measurement for payment to be as per standard drawings), re-handling of material/earth to complete the task. Depth upto 1.5 m In ordinary rock. |
| 37 | In hard rock (Blasting prohibited) |
| 38 | For MH Depth upto 1.5 mIn ordinary rock. |
| 39 | In hard rock (Blasting prohibited) |
| 40 | Providing and constructing of SEWER-BRICK (As per IS-4885 amended upto date) masonry circular manholes of \"Type-A\" with internal dia 0.90m and depth upto 1.65m having 230mm thick sewer brick masonry wall in cement sand mortar 1:4, including concreting PCC M-10 grade (1:4:8) for 225mm thick foundation including curing compaction and form work etc complete, PCC M15 for benching and channel portion, RCC M20 for 200mm thick cover slab including reinforcement, PCC M20 for fixing the manhole frame and cover using stone aggregate 20mm nominal size, 20mm thick inside and outside plaster in C. M. 1:3, inside plaster finished with floating coat of neat cement, vata in CM1:1 around pipe entering and leaving the manhole and also at the junction of masonry and concrete slab providing and fixing of SFRC foot steps of approved make at every 0.30m height fixed in CM 1:3, supplying and fixing heavy duty SFRC manhole frame and cover as per IS 12592 (Part I and II) having clear opening of 560mm, including refilling of Jhiri, including curing, watering, ramming, hydro testing of manhole, conveyance & cost of water, and dewatering complete as directed by the Engineer. Note:- Excavation of earth work and road cutting for manhole will be measured and paid separately. Manhole \"Type-A\" of depth 0.90 m |
| 41 | Providing and constructing extra depth of manhole \"Type-A\" for depth beyond 0.90 m and upto 1.65 m with SEWER-BRICK masonary including 20mm plaster inside and outside as per drawing and direction of Engineer. |
| 42 | Providing at site, lowering & laying in trenches, aligning & jointing of RCC pipes NP3 class (with s/s ends) IS: 458 - 1988 (amended up to date) marked and pipes from 300 mm upto 2000 mm manufactured through vertical / vibrated casting process all levels with Rubbergaskets (EPDM/SBR) for sewer lines as per IS: 5382 (including costof Rubber gaskets lubricants) as per drawing, sectional hydro testing of the sewer pipe line (including cost and conveyance of water to site for testing) etc., complete as directed by Engineer. Note : E/w to be measured and paid separately. Length of pipe shall be measured in between the outer wall of two manholes / Inspection chambers. Pipe in the manhole/inspection chamber’s wall shall deemed to beincluded in the item of manhole/inspection chamber shall not be payable. 200 mm internal diameter |
| 43 | Providing granular bedding having width = outer dia of pipe (Bc) + 500mm, thickness below pipe = 0.25Bc or 100mm (whichever is higher) and haunching = 0.5Bc, with graded hard crusher broken stone of 100% passing through 20mm sheive, 20 to 50 % passing through 10mm sheive and 100 % retain on 6.3mm sheive, laying in layers of thickness 10/15cm including ramming, consolidation etc complete for all type of pipes of following sizes as per drawing and or as directed by Engineer. 200 mm internal diameter |
| 44 | Construction of House Sewer Connection inside and outside of a dwelling properties to connect all the outlets of Kitchen, Bath, toilet/WC of the property to existing inspection chamber of Sewer Network, which includes Door-to-door survey of all properties to be connected with Sewer Network, Preparation of sketch / drawing of arrangement for each house with all the details and obtain approval from Engineer In charge or his representative and Preparation of as built drawing (Layout plan) in AutoCAD for each property / dwelling connection with sewer network up to manhole. Including Dismantling of all type of flooring and roads, i.e. BT/CC/WMM/interlocking block etc with mechanical cutter. Including Required Excavation of pipetrench /chamber in all type of strata of specified width up to all depth, Providing, laying, jointing and aligning of PVC-U pipes (SN-8) as per 15328 (amended up to date) / HDPE DWC (double wall corrugated) pipes of SN-8 grade as per IS 16098 (amended up to date) with required PVC/ DWC fittings with required level & location in buried position over bedding of 50 mm thick M-10 grade and in open position above ground/floor with an encasing of pipe 50 mm cover at 3 sides with M10 grade concrete, Providing, laying, jointing and aligning 160 mm dia PVC-U pipes (SN-8) as per IS15328 (Amended up to date) providing as sleeve to 110 mm dia PVC-U pipes / HDPE DWC (double wall corrugated) pipes (exposed to atmosphere) for crossing open drains, demolishing, If required and reconstruction of drain in original position with PCC M-10, Brick work with modular extruded burnt fly ash clay sewer bricks (Conforming to IS: 4885 - 1988) in CM 1:4, 12 mm thick plaster in CM 1:3 and Construction of 2 Nos brick masonry chamber of bricks class designation 75 of 115 mm wall thickness in cement mortar 1:4, clear inside dimension 320 x 320 x 550 mm, 50 mm thick base PCC 1:3:6, providing & fixing 350 x 350 mm RCC precast cover with frame of LD-2.5, earth filling in gaps, finishing with PCC 1:3:6 inside the chamber, Chamber-1 with square mouth S.W. gulley trap P-type of size 100 x 100 mm as per IS 651: 1992 (amended up to date) with CI grating, in slope around the mouth of Gulley Trap including provision for fixing of 2 nos. 110 mm dia PVC-U pipe etc. to connect a single inlet after connecting all the outlets of kitchen & bath & outlet of this chamber will connect to Chamber-2 or inspection chamber and the Chamber-2 with a provision for fixing of 2 nos. 110 mm dia PVC-U pipe etc. i.e. a single inlet after connecting all outlets of toilet & WC of premises to exiting Inspection chamber, Emptying of septic tank/soakage well etc. disposing of sludge within a lead of 5 Km and taking out the sewage, Bypass of septic tank/soakage well by providing, laying, jointing of 110 mm dia PVC-U pipes for all length from inlet to outlet, including PVC coupler, MS clamp and dismantling, repairing, making good the holes etc, Making connection with 110 mm dia PVC-U pipe with exiting inspection chamber (including making holes in Inspection Chamber) for pipes coming out from inside property and Chamber 1/2, making and repairing holes with CM in 1:4, repairing of floor and road with CC M- 30 grade same as original thickness of floor and road, watering, backfilling, compaction and disposal of all surplus material and sewage etc. to a suitable location with all lead and lift, repairing of underground utilities, if damaged, Complete job to connect a dwelling premises to sewer network including all material, labour, taxes, charges etc. as per Specifications, drawing and directions of Engineer In charge Length up to 5 m |
| 45 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall (a) 15mm dia nominal bore |
| 46 | (b) 20 mm dia nominal bore. |
| 47 | (c) 25mm (---do---) |
| 48 | use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat lid with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40mm flush bend 20mm over flow pipe with specials of standard make andmosquito proof coupling of approved municipal design complete, ncluding painting of fittings and brackets, cutting and making good the walls and floors wherever required :White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend.36.68.1 |
| 49 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever requiredWhite Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests |
| 50 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 36.60.1100 mm inlet and 100 mm outlet 36.60.1.1 S and cast iron S&S as per IS: 3989. |
| 51 | Providing and fixing P.V.C. low level flushing cistern with manually controlledevice (handle lever) conforming to IS : 7231, with all fittings and fixtures complete 10 litre capacity - White |
| 52 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete :White solid plastic seat with lid |
| 53 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make 25 mm G.I. waste pipe complete including cutting & making good the wall : Vitreous china flat back wash basin 630x450 mm |
| 54 | Providing and fixing brass bib cock of approved quality : 34.15.115 mm nominal bore |
| 55 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 34.50.1 15 mm nominal bore |
| 56 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 57 | Providing and fixing uplasticised PVC connection pipe with brass unions :34.21.1.1 15 mm nominal bore |
| 58 | P&FFull-wayValve (IS:778Mark)or wheel Valve of approved make:(a) Gun-metal 25mm nominal bore |
| 59 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore |
| 60 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 34.58.1 15 mm nominal bore, 105 mm long. Weighing not less than 138 gms. |
| 61 | Providing and fixing PTMT grating of approved quality and colour. 34.57.1 Circular type. 34.57.1.2 125 mm nominal dia with 25 mm waste hole. |
| 62 | Providing and fixing on wall face Unplasticised Rigid PVC Single socketed pipes rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (a) 110 mm dia |
| 63 | (b) 75 mm dia |
| 64 | Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Coupler (Socket) 110mm dia 31.42.1.2 |
| 65 | Reducer 110 x 75mm ,110mm dia |
| 66 | Plain Tee, 110mm dia |
| 67 | Door Tee, 110mm dia |
| 68 | Bend 45, 110mm dia |
| 69 | Door Bend (Top side), 110mm dia |
| 70 | Vent Cowel, 110mm dia |
| 71 | Providing and fixing Unplasticised -PVC pipe clips of approved design to Unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. Pipe Clip, 110mm dia |
| 72 | P-Trap, 110mm dia |
| 73 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet. 34.22.2 150 mm diameter |
| 74 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brassincluding painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern. |
| 75 | P & F Marble Urinal Partition slab both sides polished of approved design cut from marble size 900x600mm.Marble Makrana \"Aganga\" Upto to 1500 Cm2 Tiles |
| 76 | White vitreous china clay half stall urinal flat back 580x380x350 mm or angle back 450x375x350 mm with waste fittings as per IS : 2556 Vitreous china pedestal type water closet |
| 77 | Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required : White glazed fire clay kitchen sink of size 600x450x250 mm |
| 78 | Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 265mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighting not less than 263gms. Bottle trap 38mm |
| 79 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Size 600 x 450mm x 4mm thick |
| 80 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame ofapproved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357mm |
| 81 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.450MM long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms. |
| 82 | Providing and fixing PTMT grating of approved quality and colour. 34.57.1 Circular type.125 mm nominal dia with 25 mm waste hole. |
| 83 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour. weighing not less than 105 gms C.P. brass |
| 84 | P&F Tooth paste & brush holder of approved quality/ make:C.P. brass |
| 85 | WVC (1st quality, ISI marked) recessed size 150x150mm.P.T.M.T. Liquid Soap Container of 400ml capacity |
| 86 | Providing and fixing PTMT swivelling shower, 15mm nominal bore. Weighing not less than 40gms.. |
| 87 | Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators side /top /centre hung with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete ofstandard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and rivetted with 15x3mm lugs, 10cm long, embedded in cement concrete blocks 15x10x10cm of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of hinges, pivots, float glass panes with glazing clips and special metal sash putty of approved make and a priming coat of approved steel primer excluding the cost of metal beading and ot er fittings except necessary hinges or pivots complete as per approved design.Outer Boundary Gate,Outer Boundar Railing,For Balcony Portion,TRUSS WEIGHT,ISMC 100,For Plat Connection |
| 88 | Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with L-Type section made of 1.60mm thick M.S. Sheet, joints mitred and welded and grinded finish profiles required size with 15x3mm lugs 10cm long embedded in cement concrete blocks 15x10x10cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required including fixing of necessary butt hinges andscrews and applying a priming coat of approved steel primers. |
| 89 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia, steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. |
| 90 | Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution. |
| 91 | Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpetwashers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00mm thick with zinc coating not less than 275gm/m² |
| 92 | Providing ridges or hips of width 60 cm over all width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete.0.80mm thick with zinc coating not less than 275gm/m² |
| 93 | Supplying & fixing door, window, chowkhats and other frames, including antitermite treatment, M.S. flat, hold fasts of size 250x40x3mm fixed with M.S. bolt 5 mm dia 50 mm long duly embedded in cement concrete M-15grade :28.1.2 Sal wood Sal wood Grade – I (For Door),Sal wood Grade – I (For Windows) |
| 94 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formaldehyde resin in glue both sides including approved ISI marked Stainless Steel butt hinges fittings with necessary screws complete as per annexure \"A\" : 28.24.3 35 mm thick Decorative teak veneer both sideI |
| 95 | Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. |
| 96 | Providing and fixing aluminium tee channels (heavy duty) with rollers, stop end in pelmets as curtain rod.Sheesham wood Grade -I,150 mm wide |
| 97 | Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked including top cover of 6 mm commercialply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type ) curtain rod with nickel plated bracketsincluding fixing with 25x3 mm M.S. flat 10 cm long and rawl plugs 50 mm long (designation 10 no.) etc all complete,20 mm dia.For Stage |
| 98 | Providing and fixing partly paneled and partly glazed with 4 mm plain glass double leaf shutters for windows and ventilators as per approved design and drawings with approved steel fittings as per Annexure ‘A’ and width of styles, bottom and top rails 75 mm including intermediate rails 50 mm wide, beading of 25mm x 15mm size on both faces : 25 mm thick. |
| 99 | Providing and fixing factory made laminated veneer lumber glazed shutter conforming to lS : 14616 and TADS 15:2001 (Part B) , using4mm thick float glass panes for doors, windows and clerestory windows including ISI marked black enamelled M.S butt hinges withnecessary screws as per directions of Engineer-in-charge 28.14.1 30 mm thick shutters.Extra for providing heavy sheet float glass panes instead of ordinary float glass in glazed doors, windows and clerestory window shutters.(Area of opening for glass panes excluding portion inside rebate shall be measured)28.15.1 5.5 mm thick instead of 4 mm thick.Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panesexcluding portion inside rebate shall be measured)4mm thick |
| 100 | Providing and fixing expanded grill made of aluminium as per design and drawing having members section of size 7.5mm x 6.0mm andopening of size 102mm x 99mm to aluminium window/vent with required screws, Y and H aluminium sec (as per drawing) at theends and middle joints respectively complete in all respect as per direction of engineer in charge.37.17.1 Anodised aluminium (anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer For Fixed portion |
| 101 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittingswherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately). Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC15) For Front and Side Main Gate |
| 102 | Providing and fixing 12mm thick Pre-laminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainlesssteel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. |
| 103 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. completeas per the architectural drawings and the directions of engineer-incharge (Cost of aluminium snap beading shall be paid in basicitem) : With float glass panes of 5.50 mm thickness |
| 104 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost ofcutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.37.4.2 With brass cover plate |
| 105 | Providing and fixing expanded grill made of aluminium as per design and drawing having members section of size 7.5mm x 6.0mm andopening of size 102mm x 99mm to aluminium window/vent with required screws, Y and H aluminium sec (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge.37.17.1 Anodised aluminium (anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer) |
| 106 | Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 107 | Providing and fixing friction stay for aluminium windows, Ebco or equivalent, complete in all respect size 10\". |
| 108 | Providing and fixing sun control film, 25 micron thick of approved colour and shade, complete in all respect at all level, as directed by engineer in charge. |
| 109 | Wrought iron and mild steel welded work) (using angles, square bars, tees and channel grills, grating frames, gates and tree guards of any size and design etc. including cost of screens and welding rods or bolts and nuts complete fixed in position but without the cost of excavation and concrete for fixing which will be paid separately. |
| 110 | Providing and fixing Square bars or other flat welded to window, ventilators etc. |
| 111 | Malmal cloth,For Door,For Window,For Stage |
| 112 | Construction of Tube-well upto 100 Meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per IS:2800 (Part I & II) 1979 specifications.The work would be completed after obtaining sand free water.The tube well should have a throughout bore as per nominal dia of casing pipe :150 mm dia Nominal bore. |
| 113 | Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size of slotting as per IS:8110-1985 of following nominal bore sizes at site of work 150 mm Nominal Bore. |
| 114 | Supply of ERW M.S. black casing pipe ISI marked (IS: 4270/1992) of grade Fe410 of following nominal bore sizes at site of work.150 mm nominal bore |
| 115 | Supply and fixing of tube well cover of M.S. sheet (6mm thick) with nuts and bolts complete for casing size.150mm dia. |
| 116 | SITC of central govt./ state govt. authorised fire authority approved Vertical multistage Jockey pump with SS Body, SS impellor, SS shaft, mechanical seal coupled with Squirrel cage induction motor for automatic operation suitable for three phase, 415 V, 50 Hz AC supply with synchronous speed of 2900 RPM ,T.E.F.C typeconfirming to IP:55 with flexible coupling and coupling guard with the pump ,Common bed plate fabricated from mild steel channel Suitable cement concreat foundation duly plastered with antivibration pads complete in all respect. Appropriate OEM/ NABL lab test reports shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer Annexure \"A\" attached with this BSR 180 LPM suitable for 70 Mtr |
| 117 | Installation of submersible motor pump set in Tube-well/open well complete (labour charges only) including transportation of tripod chain pulley black & any other material required for lowering purpose. |
| 118 | Supplying and Laying ISI marked P.V.C. insulated submersible cable as per PWD specification for electrical Works confirming to IS:694 and as per IS 8130 : 2013 of 1.1 kV grade .Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A or C ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4 including makingconnection etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. All as per pre approved byEngineer in charge, making connections. For additional technical parameters of products/ work , refer Annexure \"A\" attached withthis BSR .4.0 Sq.mm 3 core flat / Round |
| 119 | Supplying and stacking of well decayed cow dung manure at site.Compost |
| 120 | Supplying and stacking good earth at site of work.Note: 1) Loading, unloading and carriage to be paid extra as per actual lead.2) Earth measured in stacks will be reduced by 20% foe payment |
| 121 | Supply of different varieties of tree / shrubs / climbers according to height and age of the plant at site including loading/unloading and transportation etc. complete.Different flowing shrubs 600mm to 900mm. |
| 122 | Supply of Rose Garland 1.5 feet long at site/ store i/c all complete.Different varieties of Grafted Rose plant. |
| 123 | Supply and planting following species best quality container grown healthy trees of 2 mt. min. height, well established & free from disease at site in 0.90 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required. 39.44.16 Table palmSupply of different varieties of palms indoor plants in polyethylene bags / earthen pots according to height growth and age of plant at site including loading/ unloading and transportation etc. complete.Rubber plants etc.Drasina |
| 124 | Supply of different varieties of palms indoor plants in polyethylene bags / earthen pots according to height growth and age of plant at site including loading/ unloading and transportation etc. complete.Rubber plants etc. |
| 125 | Drasina |
| 126 | Supplying and stacking good earth at site of work.Note: 1) Loading, unloading and carriage to be paid extra as per actual lead.2) Earth measured in stacks will be reduced by 20% foe payment |
| 127 | Providing and fixing wood panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled and glazed shutter 25 mm to 40 mm thick.9 mm thick Teak ply BWR one side |
| 128 | Providing & Fixing in position, Acoustical Ceiling with following Panels on approved heavy duty G.I. frame ceiling channels at 450 cto c, & intermediate channels not more than 1200 c to c, along with ply wood forms suspended with Hangers from Roof, in front of 1000 Gsm synthetic wool 50 mm thick, with Paint, including cost of required Cut-Outs, decorative mouldings / finishing-items & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour, finishing etc complete. 28.147.2 Compressed polyester fibre nonwoven 9mm panels |
| 129 | Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for :Suspended floors, roofs, landings, balconies and access platform. |
| 130 | Extra for shuttering in circular work (20% of respective centring and shuttering items). |
| 131 | Providing & Fixing in position, Carpet more than 800+ gsm, made with100% stain proof fibres of approved make along with 5mm underlay as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour, finishing etc complete |
| 132 | 25mm wooden planking, tongued and grooved in flooring including fixing with iron screws complete with : Second class teak wood |
| 133 | Providing & fixing in position, heavy duty fully upholstered Auditorium chairs 520 mm c to c tip up type. Height of back should be less than 1030 mm with plastic protective cover on back andbottom having teak wood handles. Back to back distance is 1000mm. The auditorium chairs should be of following specifications 1. Powder Coated Heavy duty MS Stand. 2. Individually moulded , ergonomically designed seat and back cushions. 3.Moulded Polyurethane Foam cushion. PU foam density 48 – 52 kgs/cu.mtr 4. Moulded Polyurethane Foam manufactured in certified ISO 9001 facility to ensure consistency in density for longevity .5.Upholstered in Foam laminated stretch sandwich Fabric for clean finish and softcomfortable feel as per the colour & pattern selected by the client. 6.Seat and Back should have moulded synthetic protective cover. 7.Wooden or PU armrest 65mm x 20mm - 330mm long . 8.Mounted using Anchor fasteners. |
| 134 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work |
| 135 | Diluting and injecting Chlorpyriphos/ Lindane E.C. 20% with 1% concentration for POST-CONSTRUCTIONAL anti-termite treatment(excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameterholes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor |
| 136 | Painting on new surface with duco paint (IC or equivalent) to give an even shade (minimum 4 coats) with preparation of surface by rubbing, primer coats, duco filler putty including polishing etc. complete:On wood work. |
| 137 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 138 | Wiring of twin control light / fan / call bell point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it\"s all accessories( J.B. , Bends etc.) , round tiles,2 nos. 18 SWG G.I. box with earth terminal, 2 Nos 6 A two way switch,3 pin ceiling rose/ Lamp holder / 3 point Connector, 3.0 mm thick ISI marked phenolic laminated sheet (IS : 2036 - 1995), Al. alloy/ cadmium plated iron screws 20 mm cup washersetc. all as per pre approved by Engineer in charge, making connections, testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07. . For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . Short point (up to 3 mtr.) |
| 139 | Medium point (up to 6 mtr.) |
| 140 | Long point(up to 10 mtr.) |
| 141 | Wiring of 3/5 pin 6 amp. Light plug point as per PWD specificationfor electrical Works with ISI marked 1.5 sq. mm nominal size FRPVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it\"s all accessories( J.B. , Bends etc.) , round tiles,18 SWG G.I. box with earth terminal of required size, 6 A switch, 3/5 pin 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet (IS : 2036- 1995), Al. alloy/ cadmium plated iron screws 20 mm cup washersetc. all as per pre approved by Engineer in charge, making connections, testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .E010301 On board |
| 142 | Providing and fixing of non modular power plug point accessories as per PWD specification for electrical Works with 18 SWG G I box of size 175 x 100 x 60 mm with earthing terminal/connector on recessed/surface with suitable size phenolic laminated sheet (IS : 2036 - 1995) cover including cost of 16 amp. Switch (IS :3854) and 3/6 pin 16 amp. socket outlet [ as per detailed in respective item in BSR], making connection , testing , etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR |
| 143 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A or C ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4, , in existing surface or recessed PVC/ MS conduit/casing capping including all as per pre approved by Engineer in charge,making connections, etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . 3x 1.5 sq.mm |
| 144 | 2 x 2.5 sq. mm. + 1x1.5sqmm(E040101 ) |
| 145 | 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. (E040105) |
| 146 | 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. (E040105) |
| 147 | 4x6.0 sqmm |
| 148 | 1 x 16.0 sq. mm. |
| 149 | 4 x 10.0 sq. mm. |
| 150 | Providing & Fixing of IK09 recessed/surface mounting heavy duty horizontal type sheet steel not less then 1.2 mm thick Distribution board as per PWD specification for electrical Works ISI marked conforming to IS-13032 & IS-8623 / conforming to IEC 61439-3. Phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link ,connecting wire of suitable rating and din bar,masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . E060620 IP-43 Double door (Three phase) 6 Way ( 18 O/G + 8 I/C ) |
| 151 | 8 Way( 24 O/G + 8 I/C ) |
| 152 | Double door (single phase) 16 Way(16 O/G +2 I/C) |
| 153 | Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. . OEM shall have submit NABL / CPRI /ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 154 | Four pole MCB50-63 A rating |
| 155 | Double pole MCB50-63 A rating |
| 156 | S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit as per PWD specification for electrical Works along with its accessories (IS: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. All relative and latest acceptance tests reports by any NABL accredited lab for the conduit shall be submitted before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . E010410 MMS ( IS:9537 P - III ) PVC conduit 20 mm |
| 157 | 25 mm |
| 158 | 40 mm |
| 159 | 50 mm |
| 160 | Providing & Fixing of non modular socket size flush type 180 wattrotary minimum 5 step fan regulator as per PWD specification forelectrical Works, ISI marked (IS:11037) made out from industrialgrade Polycarbonate or fire resistant ABS material including makingconnection testing etc. as required. All as per pre approved byEngineer in charge. For additional technical parameters of products/work , refer Annexure \"A\" attached with this BSR . |
| 161 | Making of hole in wall (brick/stone) of required size for housing exhaust fan and making good the same, with cement plaster as required of following size:: Up to 457 mm size |
| 162 | P & F 18 swg M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 163 | Providing & Fixing of Heavy duty capacitor start, copper woind Double ball bearing 900/1400 RPM single phase Exhaust fan as per PWD specification for electrical Works, conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. OEM shall be an ISO certified company. Appropriate OEM test certificate shall be submitted by contractor. Allas per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .E150901 300 mm sweep(900/1400 RPM) |
| 164 | P & F of Gravity Louver shutter of superior quality made out of frame of 18 swg M.S. sheet & Louvers made from 24 swg MS Sheet with enamel paint including cost of nuts, bolts, etc as reqd. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . E151601 Up to 380 mm size |
| 165 | Providing & Fixing of IP40 LED Surface/ Recessed / suspended mounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non - yellowish diffuser for uniform light distribution. High efficiency with 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection and in compliance to IEC standards (Integral with light fixture). System lumen efficacy of = 120 lm/Watt ,THD < 10 % , p.f.=0.95,CRI >80 ,life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testingfacilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure \"A\" attacheded with this BSRE170910 Recessed MountingE170911 36W LED light fixture 2\"x2\" with acrylic / prismatic front cover. |
| 166 | Providing & Fixing of ISO Certified company made BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan as per PWD specification for electrical Works, Conform to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) or Quality Certification such as ISO – 9001 or above , with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .E270102 1400 mm Sweep BEE 1 Star rated (service value >=4.1 to < 5 ) |
| 167 | Providing & Fixing of capacitor start, copper wound, metal body, metal blade three speed wall mounting fan of following sweep with the help of anchor bolts including making connection testing etc. as required. OEM shall be an ISO certified company. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached withthis BSR .E151201 400 mm sweep(Oscillating type) |
| 168 | Providing & Fixing of of Double ball bearing, copper wounded capacitor start single phase metallic blade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor ,making connections, testing etc. as required. OEM shall be an ISO certified company. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . E150802 300 mm sweep |
| 169 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Unarmoured/ Armoured aluminium cable of 1.1 KV grade as per PWD specification for electrical Works in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:-(a) Material :- H4- Grade aluminium conductor of purity >99.6 % & as per IS:1554 P-I / IS :7098 P – I(b) conductor shall have electrolytic aluminium confirming to IS 8130, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures.(c) OEM Must have ISO 9001 & 14001 certifications for quality assuarance & its own in house NABL lab setup for all testing facilities for cables . Appropriate type test certificate / OEM test report shall be submitted . All above as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR. 16 SQMM x 4 core ( armoured ) |
| 170 | 25.0 Sq.mm x 4 core |
| 171 | 70.0 Sq.mm x 3.5 core |
| 172 | 50.0 Sq.mm x 3.5 core |
| 173 | 10.0 Sq.mm x 2 core |
| 174 | Maintenance free Gel EarthingwithPipe in pipe / Pipein striptechnologyfilled with anti corrosive conductive compound ( CPRI Tested )below the ground in 150 - 200 mm dia. earth pit & surrounding filled with required mineralfillingcompound ( MFC should have hygroscopic property to retain the moisture for long time to create low resistance zone) and C.C.finished chamber covered with hinged type with locking arrangement C.I. Cover,C.I. Frame of size 300mm x 300mm complete testing of earth resistance as required. of following sizes. with Strip in Pipe Technology with 80 - 100 micron GI CoatingE140514 GI pipe 3000 mm long, 80 / 50 mm, Terminal 50 mm x 6 mm GI Strip |
| 175 | Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSRE140702 8 SWG copper Wire |
| 176 | 20mm x 3mm copper strip |
| 177 | Providing & Fixing of IK07 IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum LM6/ ADC12 material with heat dissipation fins on housing with UV stabilized PC/Toughened Glass cover (UV stablzation report submitted for UV cover ) and secondary lens on each LED & should be SMD type . The System level Luminaire efficacy >=120 lm/ wt with High Power LEDs is to be used and potted driver must be potted & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety ,Input Frequency 50Hz±3% Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <1000mA shown in LM79 report. The luminaire shall be BIS certified and T.C. certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened ,color Rendering Index >70 and CCT 5700K +355K. Surge protection shall be min = 4 KV internal and min 10 KV external. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced. OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR E181302 LED Street Light fixture 30 Watt |
| 178 | Providing & Fixing of Street light bracket made out from following size of \" B \" class , Medium class G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with heavy duty pole clamp, Saddles suitable fastners etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .E181704 40 mm Dia. |
| 179 | SITC of IP 40 quick make and quick break 4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 415 V, 50 Hz; O/L & S/C settings as per PWD specification for electrical Works, conforming to IS/IEC 60947 P -2:2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable foroperation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 690 V, provision for UVR , shunt trip , earth fault trip, door interlock, padlock & rotary handle , including making connections with lugs & spreaders, etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached withthis BSR .E270615 250 Amp , 35 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu |
| 180 | 200 Amp, 35kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu |
| 181 | Up to 100 Amp , 25 kA, adjustable O/L & fixed S/C setting, Ics = 100% Icu |
| 182 | Supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar as per PWD specification for electrical Works, by means of SMC / DMC type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . E080202 Electrolytic grade (Cu-ETP) Tin Coated annealed copper bus barsIACS 100% grade |
| 183 | SITC of wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as per PWD specification for electrical Works, made out of CRCA sheet . Other parametersrequired as per point (a) ,(b), (c), (d) below:-(a)Thickness of sheet shall not be less than 1.6 mm up to 600 mmlength / width of any compartment and be of 2.0 mm above 600 mm. Load bearing structure shall be of 2.0 mm thick sheet supported by base M.S. channel if required . Side walls and cable alley compartments having bolted type doors with / without detachable extension type structure(b) panel shall be duly treated for derusting in 7 tank process with dephosphating and with powder coating of minimum 70 microns on both side of panel in desired shade The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware, separate detachable gland plate M.S. base channel (min75mm) , hinged door with locking arrangement for equipment/switchgear.(c) Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 125 amp ) and by solid bus bar (>125 amp ) . All joints / interconnections of copper bus bar shall be dully tinned . Clearancebetween main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar.(d) only outer area on all sides shall be measured & panel to be fabricated only from CPRI approved fabricator. All as per drawing pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 184 | Providing & Fixing of IP 51 ( upto 500) V range Volt meter on existing panel as per PWD specification for electrical Works, making connection by PVC insulated copper conductor with PVC sleeves / channel etc. Meter shall give true RMS measurments, acc. CI 1.0 or better , with field programmable primary & sec. values PT(VT) primary upto 2000 KV. Field-programmable high and low threshold values, meter shall compliance of IS 13875 & IEC 61236. as required. OEM Must have BIS certificate and & shall have submit NABL / CPRI / ERDA lab test reports before execution &All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . E080401 Digital type |
| 185 | Providing & Fixing of CT operated direct reading type IP- 51 Ampere meter on existing panel as per PWD specification for electrical Works, making connection by PVC insulated copper conductor with PVC sleeves / channel etc. Ampere meter shall give true RMS measurement, Acc. Cl 1.0 or better , Measuring current range 50 mA to 6 A, with Field-programmable primary and secondary values CT primary up to 15000 A, Field-programmable high and low threshold values as required. compliant to IS 13875, & IEC 61326. OEM Must have BIS certificate and & shall have submitNABL / CPRI / ERDA lab test reports before execution &. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .E080610 Digital type Confirming to IEC 62053-21E080611 Below 500 A |
| 186 | Providing & Fixing of ISO certified company made selector switch of 10 A for voltmeter (4 position ) using high grade engineering material to international standards with cam assembly insulation of glass filled polyamide with high tracking index. For reliable and stable electrical and mechanical endurance double butt contacts with silver bi-metal on copper should provided . contact assembly is of operating temp range -25 degree C to 55 degree C, frequency upto 10 KHz. switch life under std. op. conditions shall be mechanically minimum 50000 operations @300 cycles/ hour and electrically 10,000 operations at 100% rated duty for 100 cycles/ hour including making connection etc. as required . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 187 | Providing & Fixing of ISO certified company made CT linked selector switch of 10 A for Ampere meter (4 position ) using high grade engineering material to international standards with cam assembly insulation of glass filled polyamide with high trackingindex. For reliable and stable electrical and mechanical endurance double butt contacts with silver bi-metal on copper should provided . contact assembly is of operating temp range -25 degree C to 55 degree C, frequency upto 10 KHz. switch life under std. op. conditions shall be mechanically minimum 50000 operations @300cycles/ hour and electrically 10,000 operations at 100% rated duty for 100 cycles/ hour , including making connection etc. as required . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 188 | Providing & Fixing of ISO certified company made UL listed , IP 65 110/220 V, unibody LED Indicating lamp IEC 60947 , CSA 22.2 with integral circuit, IP 20 terminal block, Approx. body dia for panel not less then 20 mm, length min. 50mm, front LED cover dia min. 29 mm, contact material phospher bronze for Led, PCB contacts shall be of brass (tin plated), impulse dielectric tested for 2.5 KV, Ratedinsulation resistance shall be 100 M ohm at 500VDC including connection etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .E081001 Red/yellow/Green colour |
| 189 | Blue colour |
| 190 | Providing & Fixing of IP20 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Back lit SMD Mid Power LED Downlight with die-cast aluminum housing & Heat Sink for heat dissipation with UV Stabilized non yellowish Diffuser with internal/ external BIS complience 2.5 KV surge protected Isolated driver, with Short &Open circuit protection, having efficiency > 85% and in compliance to IEC standards. System Lumen efficacy min. 100 lm/watt, THD < 10 % ,p.f.=0.95, CRI >80, life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its ownin house NABL acredeated lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure \"A\" attacheded with thisE270223 LED Downlight 18/20W |
| 191 | Providing & Fixing of ISO certified company made on load change over switch, front handle operated, four pole 415 V as per PWD specification for electrical Works conforming to IS/lEC 60947-3 : 1999 including connections , testing etc. as required .in the following rating. Appropriate type test certificate / OEM test report shall besubmitted . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .E100710 Open execution type E100712 125 A |
| 192 | Providing & Fixing of ISI marked (IS:2268-1994) ding dong/musical chime bell as per PWD specification for electrical Works, including making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 193 | Providing & Fixing of metal clad industrial plug top & socket unit with pin and sleeve type copper contact on porcelain/ bakelite base insheet steel( CRCA ) powed coated enclosure as per PWD specification for electrical Works conforming to Is 8623 & IEC61439-3 (without MCB) including , all as per pre approved by Engineer in charge,making connections,, testing etc.as required .OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work ,refer Annexure \"A\" attached with this BSR .E060910 20 A Double Pole (single phase Three pin ) |
| 194 | Providing & Fixing of energy efficient direct fit (Retrofit) Polycarbonate /Extruded Al Base Housing & diffuser SMD Mid Power LED tube (with integral driver), on existing fixture. Power Consumption of 18W / 20W system lumen efficacy = 110 lm/Watt output, internal surge protection of 2.5 KV ,THD < 15% ,p.f.=0.95,CRI >80 , life time of minimum 35000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixtureshall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure \"A\" attacheded with this BSR.E170301 4\" ,18/ 20 Watt LED Tube Without Batten ( Polycarbonate base) |
| 195 | Supply & Fixing of ABC Type (MAP 50) type powder Fire Extinguisher (Stored Pressure type) of following capacity duly current and valid BIS certification conforming to IS: 15683:2006, with Dry chemical powder used as extinguishing agent should be Mono Ammonium Phosphate 50% concentration conforming to IS14609:1999. OEM will produce supplier certificate complete with squeeze grip release valve, locking arrangement, pressure gauge and bracket including initial fill and wall suspension complete in all respect. Serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. The firm shouldsubmit the product certificate from an EN notified body & product performance test report from NABL accredited Lab as per IS 15683. . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . E245303 6 kg |
| 196 | Providing & Fixing of Electrical insulating rubber matts as per PWD specification for electrical Works, ISI marked confirming to IS: 15652 / 2006 with one side anti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. All as per pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached withthis BSR . E081201 3.3 KV, 2 mm thick with proof voltage 10 KV / 3 min. and Break Down Voltage 30 KV |
| 197 | Supplying and making one end termination with heavy duty single compression brass gland (as per IS 12943- 1990) SIBG type, heavy duty Copper/ Bimetallic lugs (IS 8337- 1976) duly crimped with crimping tool, PVC tape as per PWD specification for electrical Works etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium/copper conductor cable of 1100 volt grade as required of size. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . aluinium conducor3.5x70.0 Sq.mm |
| 198 | 4x16.0Sq.mm |
| 199 | 4x25.0 Sqmm |
| 200 | 4x50 Sqmm |
| 201 | Providing & Fixing of flush type non modular single line telephonejack as per PWD specification for electrical Works, made out fromindustrial grade Polycarbonate or fire resistant ABS material, including making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 202 | Supplying and drawing PVC/ Polythene insulated and PVC sheathed unarmoured telephone cable with 0.5 mm dia. Tinned / annealed copper conductor taped & confirming to latest TEC specification , GR / WIR/06-03 March 2002 of following pair in existing surface or recessed PVC/MS conduit/casing capping including all as per pre approved by Engineer in charge, making connections, as required. For additional technical parameters of products/ work , referAnnexure \"A\" attached with this BSR E040302 2 pair |
| 203 | 10pair |
| 204 | Providing & Fixing of 18 SWG G. I. / M .S. Sheet boxes as per PWD specification for electrical Works, duly finished with two coats of red oxide and with earthing terminal of following sizes (nominal size) in recessed/surface as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .E050110 18 SWG M. S. Sheet boxesE0501102 100mm x 100mm x 60mm |
| 205 | Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copperwire insulated with PVC, UTP (Unshielded Twisted Pair), Category6, Class E, 100 Ohm Impedance, Indoor Cable as per latestammendments of ANSI/TIA/EIA-568 , The copper conductors should be balanced twisted in pairs, seperated by a cross-member fluted pair divider & protected by PVC Jacket. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 206 | Supply, Installation, Testing and Comissioning of Rack mounted 19\" 1U, 24 Port Unloaded, 1.5-1.6 MM CRS chasis, powder coated, sheet steel, made of plastic (ABS), Modular Patch Panels (without I.O.) with Rear Cable management system and mounting hardware to mount the patch panel. Should have port identification numbers printed/engraved on front of the panel, . There should be a provisionfor each port/jack on the panel and reusable removable on field from the panel complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 207 | Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A patch cords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with FRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectors as per ANSI/TIA/EIA 568 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards, According. to TIA568, minimum requirement for 1G BASE-T/ 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes, Minimum 750 to 1000 mating cycles in plug contacts for long durability complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR.E2006121 Mtr |
| 208 | 2 Mtr |
| 209 | SITC of Intelligent Manageable Ethernet Switches providing 24 x 10/100/1000 Fast Ethernet ports- and 2 dual purpose uplink (provision for Copper / Fibre Giga connectivity) with LAN based Software. The LAN based S/W supports enhanced integrated security, including Network Admission Control (NAC), advancedquality of service (QoS), availability and scalable management to enable new converged applications |
| 210 | Supply Installation testing & Commissioning of Radial / mixed flow ISI marked water filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034:2018 and IS 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 with required accessories including making connection suitable for Bore well. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to switch board.All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . E210710 100 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively. E210713 2.0 HP, 1-Ø, (7- 95)Mtr, (55-22) LPM |
| 211 | Supply & Fixing of FR PVC insulated & sheathed 3 core flexible copper conductor as per PWD specification for electrical Works confirming to IS:694 and as per IS 8130 : 2013 of 1.1 kV grade .Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4 including making connection etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. All as per preapproved by Engineer in charge, making connections. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . E222703 4.0 Sq.mm |
| 212 | Providing & Fixing of HDPE pipe ISI mark (IS:4984/2016 ) for water supply (suitable for submersible & jet pump) with required fittings ie socket, elbows, tee etc. complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .E210410 for vertical installationE210411 40 mm OD 6 kg / cm2 |
| 213 | Supply Installation testing & Commissioning of ISO certified company made DOL/Star-Delta Starter panel made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. Appropriate type test certificate / OEM test report shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .E211410 For single phase Submersible / Monoblock pump E211411 0.5 HP to 3.0 HP (DOL starter |
| 214 | Providing & Fixing of extra down rod of 15 mm dia . ERW (Electrical resistance welded ) of 1.6mm nominal thick medium duty steel pipe including cutting, threading, drilling, fixing quarter pin etc as reqd. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\"attached with this BSR . |
| 215 | Supply , Installation, Testing and Comissioning of ISO certified company made Air Cooled Hi Wall split type Air conditioners with latest star rating system as per BEE amended upto date complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU), R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, aircirculation of following capacity with Scroll / rotary compressor. Min 5 year OEM warranty both compressor and PCB. NABL accredeated as per IS/ISO/IEC 17025 standards / CPRI / ERDA lab testing reports as per IS 1391(Part-2) 2018 with OEM certificate must submitted to engineer in charge. All as per pre approved by Engineer in charge. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . E221910 Non Invertor Type E221913 1.5 TR with 3 star rating of BEE (ISEER not less then 3.5 ) |
| 216 | Supply & fixing MS powder coated stand suitable for 1.0/1.5/ 2.0 Tr outdoor type of Split AC. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 217 | Making hole in stone masonary/ RCC wall/ RCC slab with core cutter for accomodating refrigerant pipe/ drain pipe/ MS pipe/ cables etc of following diaE222903 150 mm dia per running inch length |
| 218 | Supply, Installation, Testing and Commissioning of Wall mounted ISO 9001:2015 & 14001 or higher level certified company made Communication enclosure (Rack) of Minimum 500 MM Depth with made from CRCA & hot dip powder coated, front sturdy sheet steel frame folded from one piece and welded with minimum 5mmtoughened glass door,Vertical Mounting Rail 1.6 MM with \"U\"Markingwith All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19\"angles with wall mounting provision on wall. Accessories like: 1 No of 19\" 1U Horizontal Cable manager, 2 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware , 1 No of 19\" 1U, mountable socket strips with 6 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with fastner of suitable capcity etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 219 | 9 U wall mounted Enclosure |
| 220 | Supply , Installation, Testing and Comissioning of Unmanaged Switch Plug-and-play - easy setup with no configuration or no software needed, following Port fast ethernet - 8 10/100/1000 MBPS gigabit auto-negotiation RJ45 ports, IEEE 802.3x flow control,supports auto-MDI/MDIX, eliminating the need for crossover cables including making connection etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\"attached with this BSR . 24 Port E201802 |
| 221 | Providing & Fixing of ISO Certified company made ISI marked (IS:2082) of 5 star rated vertical storage water heater with outer casing made of M.S.sheet finished with anti-corrosive powder coating,inner tank made of pure electrolytic copper/stainless steel / SPHP, Tubular copper sheathed and Nickel plated heating element/ twin ceremic cartridge heating element, stem type thermostat and thermal cut out, Dual indicating lamps for power supply and thermostat, PUF insulation, Pressure release valve,fusible plug etc. as required held in position with 4 no. rag bolts,duly wired with 3 core 2.5/4.0 Sqmm PVC insulated & sheathed copper conductor and 16 A/25A three pin plug top with Portable Residual Current Device ( PRCD ) facility form OEM ,including making inlet,outlet heavy gauge C.P./ Flexible alloy connection,testing etc. complete in all respect. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . E160103 15 Ltr. |
| 222 | SITC of ISO Certified company made MNRE approved & confirming to IS:12933 P-1,2,3 & 5 Flat Plate Collector type solar hot water system with collector, insulated stainless steel (SS grade:304) storage tank with electrical back up with Portable Residual Current Device ( PRCD ) facility form OEM , CRCA Powder coated /MSstand for Collector & Tank etc. as required. of following capacity complete in all respect. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .E162903 250 litre/ day |
| 223 | Supply Installation testing & Commissioning of ISO certified manufacturer made Monoblock motor pump set ISI marked (IS:9079-2002) with TEFC motor, motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011. with Stainless steel Impellor, Stainless steel shaft, Mechanical seal, Single/Three phase ( 240 - 440 V ) permanent split capacitor type (PSC), fitted with thermal overload protection, . Including cost of hardware etc on existing platform complete. Pump shall have following HP Rating, phase, Head, minimum Discharge respectively complete in all respect. Appropriate type test certificate / OEM test report shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .. Non Self priming pumps E210807 7.5 HP, 3-Ø, (20-32)Mtr, (1060-900) LPM |
| 224 | Providing & Fixing of IK07 IP-66 protected high power LED flood light system with Pressure diecast aluminium housing LM6/ ADC12 material , toughened glass diffuser with suitable lenses on LED to achieve various beam angles, 240 volt, 50Hz, of high power LED lamps . Integrated driver must be potted & has a unique BIS R number shall be high efficiency having efficiency more than 85 % and in compliance to BIS certified and T.C. certificate. The System level Luminaire efficacy >=120 lm/ wt with High Power LEDs is to be used . LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety . Input Frequency 50Hz±3%, Power Factor >0.95 ,driver Efficiency >85% , THD(I) <10% , driver current <1000mA shown in LM79 report. driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector Must be provided, Surge Protection Min >=4KV internaland 10KV external, System life of 30000 Burning hours with 70% of Initial Lumens maintained, color Rendering Index >70 and CCT 5700K ±355K. Driver current <1000mA shown in LM79 report. Manufactures Word Mark/Name Engraved/Embossing/Screen printing on die cast housing to allow traceability/authenticity. Fixture shall be IS 10322 Complianced. OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additionaltechnical parameters of products/ work , refer Annexure \"A\" attached with this BSR E181203 High Power LED Flood Light 70W |
| 225 | High Power LED Flood Light 100W |
| 226 | Supply, Fixing and testing of following capacity wall mounted stablisers having output voltage variation from 200V to 250V(+/-5%) with input voltage variation from 170V to 260V, time delay facility from 2 to 4 minute and high cutoff at 270V complete in all respect E074602 4 kVA |
| 227 | SITC of Silent DG Set (As per CPCB norms) complete with 1500 RPM Diesel Engine of suitable BHP & AC Brush less SPDP Alternator mounted on a common base Frame & coupled through a flexible coupling or close coupled. Alternator shall be self regulated with standard Alternator Protection( Over voltage , over speed & under voltage, under speed warning & shutdown). Engine shall have residential silencer, up to 3 M exhaust piping , electronic / Mechanical governor, Manual & electric Start ,Batteries,Engine instruments panel, AVM and with Weatherproof, powder coated Accoustic enclosure for DG set for sound attenuation fabricated from 1.6 mmCRCA sheet steel (structure) with side wall fabricated from 1.6 mm CRCA sheet & filled with 100mm thick glass wool(96Kg/m3)/Foam. as per IS 8183 the doors of 100 mm thick and fabricated from 1.6mm CRCA sheet packed with accoustic material, canopy fixed with axial flow fan , All doors/ opening are sealed with neoprene/EPDN gaskets. The enclosure has built in fuel tank, residential silencer (isolated from main DG chamber) with protection and tripping of DG setagainst temperature of more than 50 degree centigrade. All controls for operation of DG set are from outside the enclosure with DG control panel having Microprocessor based Genset monitoring & control system, MCCB, Ammeter, Voltmeter, PF meter, frequency meter, KWH meter, Ind.lamps etc. mounted inside enclosure , visible and accessible from outside. The enclosure should be suitable for following capacity DG sets and alternator. Noise level shall be less than 75 dBA at a distance of 1 Mtrs. duly certified by authorised agency etc. complete in all respect of following capacity :E231520 Radiator Cooled & Turbo ChargedE231526 62.5 KVA at 0.8 pf 415V 50Hz 3-? |
| 228 | SITC of Auto main failure (AMF) Panel fabricated from CRCA sheet steel 2 mmThick , Powder coated finish , Engine Start & Stopcommands, control Relays , selector switches for Ammeter & Voltmeter, Ammeter & Voltmeter , Control & Power Contactors, Timers, Electronic Hooter ,Visual & Alarm indication for faults, UPS, operator interface panel complete in all respect suitable for following capacity DG sets: PLC Based: 50 to 63.5 KVA |
| 229 | Plate Earthing as per PWD specification for electrical Works as per IS:3043 with copper Earth plate of size 600mm x 600mm x 3.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. \"B\" class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 230 | Supply and erection of M.S. Galvanized Octagonal pole ( as per BSEN 40-3-3:2003 /BSEN 10025/IS 2062 IS:875 Part-1 – 2015/ for MS plate for base flange )of following length and dimension as per table P-01 with base plate on the cement concrete foundation of M- 20 grade (1:1.5:3) as per IS 456/IS 2911. with the help of anchorbolts of grade 6.8 (IS: 1367 P III ). The pole shall have a weatherproof flush door and locking arrangements. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure\"A\" attached with this BSR . E180510 Octagonal MS Poles made of S-355JO grade steel sheet , folded lengthwise to obtained Octagonal shape, having single longitudinalseam weld and hot dipped galvanised internally & externally in accordance with IS 2629. (See Table P -01 for specs.) 7 Mtr. |
| 231 | P & F of IP65 IK10 protected LED Bollard fixture. Light Fixture made of powder coated alluminium/Steel housing with diffuser for uniform distribution. The System level Luminous efficacy > 85 Lumen/W. SMD LEDs . CRI>70, CCT: 3000/4000/6000 K. The integral SMPS based electronic driver must be constant current and inbuilt surge protection of min. 4KV(L-N) and efficiency > 85%, PF>0.9 and input Voltage range of 90- 270V AC at 50Hz. System life of 50000 burning hours with 70% of Initial Lumens maintained. Light should include quick connecting cable coupled with various mounting accessories. Light output in Cool white or Warm White Colour as per engineers choice. Fixture must be in compliance with IS/CE Standards.0.5 mtr high bollardGroup 1( RUIDP 2017) |
| 232 | Providing & Fixing of IK07 IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum LM6/ ADC12 material with heat dissipation fins on housing with UV stabilized PC/Toughened Glass cover (UV stablzation report submitted for UV cover ) andsecondary lens on each LED & should be SMD type . The System level Luminaire efficacy >=120 lm/ wt with High Power LEDs is to be used and potted driver must be potted & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety ,Input Frequency50Hz±3% Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <1000mA shown in LM79 report. The luminaire shall be BIS certified and T.C. certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened ,color Rendering Index >70 and CCT 5700K +355K. Surge protection shall be min = 4 KV internal and min 10 KV external. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allowtraceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distributionboard/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connectionstesting etc. as required. . OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technicaparameters of products/ work , refer Annexure \"A\" attached with this BSR . Single pole MCB3 A to 5 A rating |
| 233 | 6 A to 32 A rating |
| 234 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Unarmoured / Armoured aluminium cable of 1.1 KV grade as per PWD specification for electrical Works in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:-(a) Material :- H4- Grade aluminium conductor of purity >99.6 % & as per IS:1554 P-I / IS :7098 P – I(b) conductor shall have electrolytic aluminium confirming to IS 8130, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures.(c) OEM Must have ISO 9001 & 14001 certifications for quality assuarance & its own in house NABL lab setup for all testing facilities for cables . Appropriate type test certificate / OEM test report shall be submitted . All above as per pre approved byEngineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR.6.0 Sq.mm Armoured Cable 4 core |
| 235 | SITC of ISO certified company made air cooled ducted split typeair conditioning machine with each having a capacity and details as mentioned below suitable for operation on R-32/R-410A R-407 Green refrigerant comprising of single/twin Scroll / Rotary / Reciprocating type compressor hermatically sealed complete with automatic capacity, safety switches, lubrication system,with min 5 year OEM warranty both compressor and PCB , Suitable capacity squirrel cage induction motor with class \"B\" insulation suitable for operation on 415 + 10% volts, 50 Hz, A.C. supply for Blower motor, Necessary drive arrangement for blower motor, Matching Air cooled condenser with necessary fittings for refrigerant piping connections, necessary structural support for mounting condensers, Microprocessor based control panel complete with accessories, machine isolation / disconnect switch, valves and accessories to inter conne ct compressor and condender including pressure testingvacuum. Necessary starters suitable for Indoor & outdoor unit complete with O/L , U/V, phase reversal protection, single phase preventors etc complete as required.. NABL accredeated as per IS/ISO/IEC 17025 standards / CPRI/ERDA lab testing reports as per IS 1391 with OEM certificate mustsubmitted to engineer in charge. All as per pre approved byEngineer in charge. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , referAnnexure \"A\" attached with this BSR . E222110 Ductable Split type8.5 TR |
| 236 | Supply , Installation, Testing and Comissioning of ISO certifiedcompany made Air Cooled Hi Wall split type Air conditioners withlatest star rating system as per BEE amended upto date complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU), R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. Min 5 year OEM warranty both compressor and PCB. NABL accredeated as per IS/ISO/IEC 17025 standards / CPRI/ ERDA lab testing reports as per IS 1391(Part-2) 2018 with OEM certificate must submitted to engineer in charge. All as per pre approved by Engineer in charge. All as per pre approved byEngineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .E221920 Invertor Type 1.8/2.0 TR with 5 star rating of BEE (ISEER not less then 4.5 ) |
| 237 | Supply , Installation, Testing and Comissioning of ducting made from GSS of class VIII & fabricated as per IS:655 and as per approved drawings & designs including the cost of hangers, supports, angle, expansion fasteners , closed cell neoprene gasket T&P etc. as required of following gauge:- All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .0.63mm (24 G) |
| 238 | 0.80mm (22 G) |
| 239 | Supply and fixing duct insulation with 50 mm thick Expanded Polystyrene Thermocol (ESP) sheet of density 24 kg/cu.m after applying two coats of cold setting adhesive (CPRX Compound) and binding sheet with chicken wire mesh and applying cement mortar plaster (1:4) including primer & painting (suitable for outdoor aplication) matching with building colour or as per direction of Engineer incharge as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 240 | SITC of Interconnecting refrigerantpipe work withclosed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications including chase cutting, supports etc. as required.6.35 mm |
| 241 | 9.53 mm |
| 242 | 12.7 mm |
| 243 | 15.88 mm |
| 244 | Supply and fixing of acoustic lining of ducts with following thick, resin bonded glass fibre insulation rigid board with density 48kg/cum fixed in frame work covered with reinforced black fibre glass tissue and finished with 0.50 mm perforated aluminium sheet with 3mmperforation at 6mm center to center fixed with cadmium plated screws etc. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/work , refer Annexure \"A\" attached with this BSR .25 mm thick fiber glass |
| 245 | 12 mm thick fiber glass |
| 246 | Providing & Fixing of ISI marked (IS : 15778 - 2007) Rigid CPVCdrain water piping 6 kg/ cm2 with fittings like elbow, soket, Tee etc& support with MS hanger on ceiling or recessed in wall withchasing & plastering with 6 mm thick closed cell elastomeric nitrilerubber insulation complete in all respect. All as per pre approved byEngineer in charge.For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 247 | Supply & fixing MS powder coated stand suitable for 1.0/1.5/ 2.0 Troutdoor type of Split AC. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work ,refer Annexure \"A\" attached with this BSR . |
| 248 | Supply & fixing MS powder coated stand suitable for 2.5/3.0/4.0 Troutdoor type of Split/Ductable/Tower AC. All as per pre approved byEngineer in charge. For additional technical parameters ofproducts/ work , refer Annexure \"A\" attached with this BSR . |
| 249 | Supply and fixing aluminium foil faced resin bonded 50 mm thick fibre glass insulation of density 24 kg/cu.m after applying two coats of cold setting adhesive (CPRX Compound) sealing all joints withself adhesive tape & finished with 26 G Aluminium cladding.complete in all respect. (For Outdoor applications-air conditioningducts) All as per pre approved by Engineer in charge. Foradditional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 250 | Return air grill without volume control damper |
| 251 | Supply & fixing of evaporative cooling Celdec pads of 200mm Thick made out from impregnated cellulose paper media of imported origin including fixing in Air washer complete in all respect. All as per pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached with this BSR |
| 252 | Supply, Installation,Testing & Commissining of 12 watt Celing Speakers (including cutting making good) complete in all respect. As per direction Engineering incharge and as per Design drawing |
| 253 | Supply, Installation,Testing & Commissining of 240W booster amplifier type LBD 1935complete in all respect. As per direction Engineering incharge and as per Design drawing |
| 254 | Supply, Installation,Testing & Commissining of 480W booster amplifier type LBD 1938complete in all respect. As per direction Engineering incharge and as per Design drawing |
| 255 | Supply, Installation,Testing & Commissining of 240W mixer amplifier type LBD 1916complete in all respect. As per direction Engineering incharge and as per Design drawing |
| 256 | Supply, Installation,Testing & Commissining of Plena VAS call station type LBB 1956complete in all respect. As per direction Engineering incharge and as per Design drawing |
| 257 | Supply, Installation,Testing & Commissining of Plena VAS controller type LBB 1990complete in all respect. |
| 258 | Supply, Installation,Testing & Commissining of Electro-voice (EV) w/l mike system type R-300, complete in all respect. |
| 259 | Supply, Installation,Testing & Commissining of 12 w volume control, type LBC 1400/10, complete in all respect. As per direction Engineering incharge and as per Design drawing |
| 260 | Supply, Installation,Testing & Commissining of MusicSource, type PLE-SDT,complete in all respect. As per direction Engineering incharge and as per Design drawing |
| 261 | Supply, Installation,Testing & Commissining of M.S.racksuitable formounting aboverackmountable items, complete in all respect. |
| 262 | Supply, Installation,Testing & Commissining of Protocol integration connectors, complete in all respect. As per direction Engineering incharge and as per Design drawing |
| 263 | Supply, Installation,Testing & Commissining of STP CAT 5 Cable, complete in all respect. As per direction Engineering incharge and as per Design drawing |
| 264 | Supply, Installation,Testing & Commissining of AudioCable2x1. Sqmm, complete in all respect. As per direction Engineering incharge and as per Design drawing |
| 265 | Supply, Installation,Testing & Commissining of Shielded Audio Cable2x1.0 Sqmm, complete in all respect. As per direction Engineering incharge and as per Design drawing |
| 266 | P & Fof IP20 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Downlight with die-cast aluminum housing & Heat Sink for heat dissipation, high purity reflector with external driver having efficiency > 85% and in compliance to IEC standards. Power Consumption of = 7W/ 10W / 15W / 18W with ~ 500 / 750 / 1100 / 1250 lumens, System Lumen efficacy of 70 lm / watt output suitable to replace 1x18W / 2x18W / 2x 26W CFL Downlights, life time of 50000 Burning Hours with 70% of intial Lumen maintaned. CCT 3000°K , 4000°K& 6000°K. Fixture shall be CE compliance.LED Downlight 18/20W |
| 267 | LED Downlight 14/15W |
| 268 | Warm White LED Par Can Light High Power 54x3W Warm White LED• Voltage: AC 90V-245V/50-60Hz • Power: 180W• Fuse:3A• Lamp: 54pcs 3W warm white LEDs • Beam angle: 15~45 degree (selectable) • Life time: >100 thousand hours• Control: DMX512, Master-slave, stand-alone, music Activate• DMX Channel: 6CH • DMX signal: Input/Output: 3-pin XLR As per direction Engineering incharge and as per Design drawing |
| 269 | Voltage 110V~240V/50-60Hz Gobo Wheel fixed gobo + white Rotation gobo 9 gobo + white changeable Prism 8 facet prism + 4 Linear prism + 16 facet prism each 2 prism can mixed together for using frost func Wash Effect Adjustable Wash Effects Angle Focus Linear adjustment Dimmer 0-100% Linear Adjustment Pan / Tilt X Axis 540 deg Y Axis 270 deg Automatically Accurate Beam Angle Parallel Beam Angel 2.5 deg - 39 deg Control Mode Standard DMX512, Automatic and Master / Slave Mode Weight 22kg Ballast Electronic ballast Lamp OSRAM SIRIUS HRI-440W Colour Wheel 11 Color Colours + white As per direction Engineering incharge and as per Design drawing |
| 270 | Dracast Fresnel 1000 Bi-Color LED Light 7\" Fresnel Lens 15-60 Degree Adjustable Beam Angle Variable Color: 3,200-5,600K CRI: > 90 Yoke with 5/8\" Receiver 1,000W Tungsten Halogen Equivalent Onboard DMX512 100-240 VAC Mains, 24 VDC Battery As per direction Engineering incharge and as per Design drawing |
| 271 | 1000W spun aluminium PARCAN made out of spun aluminium 16 SWG in 2 piece cylindrical construction with punched slot on Parcan housing for natural ventilation and floating ceramic GX16d base lamp socket, 3mtr copper flexible PVC insulated power cable with 3 pin CE insulated plug, Yoke made of MS flat 25 X 3mm with 13mm free mounting hole to fit the adaptor, spigot with 28mm and filter frame but without lamp with below specifications: • \"Lamp: 1000W 240V PAR-64 • Lamp Socket: Ceramic type GX 16D • Power Cable: 3 core,1 Sq.mm copper PVC insulated flexible cable with 10 amps double pole toggle switch • Housing: Aluminium sheet cylindrical construction with black epoxy polyester powder coated\" • Switching options: Local control and Digital DMX control through Dimmer • Dimming option: Digital DMX control through Dimmer • Yoke: Fabricated using MS flat-accepts mounting on 28mm spud • Focus: Sealed beam angle • Accessories: Filter frame. As per direction Engineering incharge and as per Design drawing |
| 272 | 2000W Fog machine wire / remote / DMX 512, electronic control temperature. Smoke output 20000cuft/min @ 12Mtrs. As per direction Engineering incharge and as per Design drawing |
| 273 | 19\"\" DIN RACK for housing for mounting Power distribution center components, MCB\"s, 6Channel dimmers as per electrical standards. As per direction Engineering incharge and as per Design drawing |
| 274 | Avolite light controllerAs per direction Engineering incharge and as per Design drawing |
| 275 | 230W RGBW Gobo Pattern Prism Head Moving Stage Effect Light Voltage: AC 100V / 240V Frequency: 50 / 60Hz Power: 230W Light color: RGBW Channel: 16 1 gobo wheel: 17 gobos + white 1 color wheel: 14 colors + white 1 rotated prism: 8 facet Electronic dimmer: 0-100% Pan: 540 degree Tilt: 270 degree Prism quantity: 8 Beam angle: 4 degree Light output: 20m / 65ft Control mode: DMX512 signal / AUTO run / sound activated / master-slave control Light effect: Beam / gobo / prism light / color jumping / strobe / dimming Average service life: 2000h Power adapter: US standard Material: Aluminum alloy and ABS Item size: 52.3 * 33.7 * 51.1 cm / 20.6 * 13.3 * 20.1 in (L * W * H) Item weight: 16.280 kg / 35.9 lb Package size: 54 * 45 * 40 cm / 21.3 * 17.7 * 15.7 in (L * W * H) Package weight: 18.469 kg / 40.7 lb As per direction Engineering incharge and as per Design drawing |
| 276 | Supplying, Installation, Testing & Commissioning of central govt./state govt. authorised Fire authority approved Electric Driven Mainfire pump for Sprinkler / Hydrant applications suitable for automaticoperation and consisting of following details given as A, B, C, D,E,F,G and H. (A) Horizontal Single / Multi stage Centrifugal End suction, back pull out type pump complete for delivery of below mentioned discharge ,including bypass arrangement for Testing of pump (B) Material of construction : Pump Casing - Cast Iron, Impellor - Bronze, Shaft - SS 410, Packing - Mechanical Seal (C)Pump shall be capable of furnishing not less than 150 % of rated capacity at a head not less than 65 % of the rated head. The shut off head shall not exceed 120 % of rated head (D) Squirrel cage induction motor should be IE2 class as per IEC60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 suitable for3 phase, 415 V, 50 HZ, Ac supply 2900 / 1450 RPM T.E.F.Cconfirming to IP:55 , of required HP suitable for the above pump,along with flexible coupling , coupling guard complete in all respect .( E) Common bed plate fabricated from mild steel channel for installation of pump and Motor including anti vibration pads.(F) Pump must be inspected by third party like RITES / PDIL at manufacturer\"s premises and inspection report is to be submitted.(G) Suitable cement concreat foundation (1:3:6) duly plastered with (1:4) ratio(H) All as per pre approved by Engineer in charge. For additionaltechnical parameters of products/ work , refer Annexure \"A\"attached with this BSR . 1620 LPM suitable for 56 Mtr Head, single stage, 2900 RPM |
| 277 | SITC of diesel engine drive Standby Pump suitable for automatic operation consisting of the following A, B, C. .The Diesel driven pump shall be suitable for following discharge: (A) Horizontal multi stage centrifugal suction type pump complete for delivery of below mentioned discharge complete with necessary flexible pipe, sluice value on the suction side (all items shall be matching the suction side of the pump) and pressure gauge, sluice valve and non return valve on the delivery side (all of the necessary dia) and including bypass arrangement for testing of pump (B) Water cooled Diesel Engine developing suitable BHP for the below mentioned discharge at 1800 RPM, flexible coupling and coupling guard with the Pump, common bed plate for mounting of the Engine and Pump, d cushy foot, damping arrangement by cushy foot, Diesel Engine starting Panel for starting of the engine automatically with a unit of battery of 12/24v, 88 Ah, 13/21 plate , Exhaust Pipe of minimum 10 M length, with muffler, day oil tank of 300 1ts capacity with first charge and hand operated oil pumping set, Supply, installation, testing, & commissioning of electric driven automatic pressurization pump set C) Horizontally mounted single stage centrifugal end delivery pump of below mentioned discharge with necessary sluice valve on the suction side (all items matching the suction side of the pump) and sluice valve, non return value, pressure gauge on the delivery side including by pass arrangement for testing of the working of the pumping set as required.(D) Radiator cooled Diesel Engine developing suitable BHP for the below mentioned dischargeat 1500 / 1800 RPM, flexible coupling and coupling guard with the Pump, common bed plate for mounting of the Engine and Pump,Antivibration damping arrangement by cushy foot, Diesel Engine starting Panel for starting of the engine automatically if the Normal electrical supply fails with a unit of battery bank of 12/24v,180 Ah, Lead Acid Battery with Boost / Trickle charger as required for operation of Diesel engine, Exhaust Pipe of suitable diameter minimum 10 M length, with muffler, day oil tank of 300 1ts capacity with first charge and hand operated oil pumping set, 1620 LPM at 56 Mtr Head ( 40 HP Engine) |
| 278 | Supplying, Installation, Testing & Commissioning of central govt./state govt. authorised fire authority approved single stageCentrifugal End suction, back pull type Terrrace pump with Bronzeimpellor, SS shaft, mechanical seal coupled with Squirrel cageinduction motor (IE-2 class) for automatic operation suitable forthree phase, 415 V, 50 Hz AC supply ,T.E.F.C type confirming toIP:55 with flexible coupling and coupling guard with the pump,Common bed plate fabricated from mild steel channel ,Suitablecement concreat foundation duly plastered with anti vibrationpads.aincluding cost of suitable rating Control panel as per rating ofMotor with 4 pole MCB, automatic DOL starter, Single phase Preventor , overload protection rely, contactors, MCBs , interlocking wiring , ferruling, potential free contact etc complete in all respect. Appropriate OEM/ NABL lab test reports shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .450 LPM with 35 mtr head |
| 279 | Supplying, Installation, Testing & Commissioning of pressure switches for Main, Jockey, Terrace pump and standby Diesel pumps, including necessary control wiring From pressure switch upto control panel and Ball valve complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 280 | Providing & fixing 100mm dia bourden type, Stainless steel dial type pressure Gauge (0 - 16 Kg ) range, 3 / 8 \" BSP bottom entry onPump Delivery Line complete with Ball valve complete in all respect.All as per pre approved by Engineer in charge. For additionaltechnical parameters of products/ work , refer Annexure \"A\"attached with this BSR |
| 281 | Providing & fixing vane type water flow switches with contacts for installation in 50 mm to 150 mm dia M.S. pipe for a service pressure up to 20 Kg / Sq.cm complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 282 | Supplying, Installation, Testing & Commissioning of floor mounted dust and vermin proof compartmentalised cubical type main fire pump control panel made out of CRCA sheet , required hardware ,duly treated for derusting in 7 tank process with dephosphating and with powder coating on both side of panel in desired shade The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness , separate detachable gland plate M.S. base channel ,hinged door with locking arrangement for equipment/switchgear . Thickness of sheet shall not be less than 1.6 mm up to 600 mm length / width of any compartment and be of 2.0 mm above 600 mm. Load bearing structure shall be of 2.0 mm thick sheet supported by base M.S. channel if required . Side walls and cable alley compartments having bolted type doors and having accessories/ switch gear (as per Specf Ch-06 & 08) as below:- complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR Incomer400 Amp. TPN MCCB (adj.O/L) with Extended ROM, 36 kA, with Thermal magnetic release, Analouge Ammeter, Voltmeter, Selector switches,CT, Indicating Lamps, 500 Amps FP Alum. Bus bar with with heat shrinkable sleeves. Out going (a) 200 Amp. TPN MCCB(adj.O/L) with Extended ROM, 35 kA, with Thermal magnetic release, Digital Ammeter, Voltmeter, Selector switches,CT, Indicating Lamps for \"ON\", \"OFF\", \"TRIP\" 1 no. star Delta Starter of 75 HP with thermal over load relay, timer, push buttons, Auto / Manual selector switch, Single phase preventor - 2 Sets (b) 63 Amp. TPN MCCB (adj.O/L) with Extended ROM, 25 kA, with Thermal magnetic release, Digital Ammeter, Voltmeter, Selector switches, CT, Indicating Lamps for \"ON\", \"OFF\", \"TRIP\" 1 no. Star Delta / DOL Starter of5 - 15 HP with thermal over load relay, timer, push buttons, Auto / Manual selector switch, Single phase preventor - 1 Set © One no. Diesel Engine Auto Starting kit with Auto . Manual selector switch & 3 attempt starting device, timers, relays, Indicating lamp for High / Low Lub. Oil pressure, High water temperature and engine ON indication, Battery charger, suitable for 12 V / 24 V DC with trickle / boost selector switch, DC ammeter & voltmeter (d) System controller to control Operation Main Electric pumps, Diesel pump, jockey pump in sequence as per specs. Consisting of relays, timers, sensors, annuciation window for fault indication. |
| 283 | Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class pipes conforming to IS 3589 / 1239 part-I for hydrent and sprinkler applications including cutting, screwing, welding etc & malleable iron fittings like elbows, tees, flanges, tapers, reducer, with compressed asbestos gaskets etc. fixing the pipe on the wall/ceilingwith suitable clamps, hanger and nuts bolts as per approvedspacing. complete with painting of one coats of Red Oxide and two or more coats of synthetic enamel paint of Post office red shade complete as required.Complete installtion shall be pressure tested at 14kg/sqcm for 24 hr as per practice complete in all respect.Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . a) 25 mm dia |
| 284 | b) 32 mm dia |
| 285 | c) 40mm dia |
| 286 | d) 50 mm dia |
| 287 | e) 80 mm dia |
| 288 | f) 100mm dia |
| 289 | g) 150 mm dia |
| 290 | h) 200 mm dia, 6.0 mm thick |
| 291 | Providing, Fixing, Jointing, Testing &Commissioning of Heavy duty MS C class pipes conforming to IS 3589 / 1239 part-I for hydrent and sprinkler applications underground rings including cutting,screwing, welding etc & malleable iron fittings like elbows, tees, flanges, tapers, reducer with compressed asbestos gaskets, nuts, bolts etc. including laying of pipe in excavted trench of 1.0 mtr depth with cleaning,wrapping and coating of the pipe with 4 mm thick tar based polymaric corrosion protection tape including applying uniform coat of cold pipekot primer as per IS; 10221 for protection against corrsion.complete in all respect. (Excavtion of trench shall be paid extra as per Item no E130500 ). Complete installtion shall be pressure tested at 14kg/sqcm for 24 hr as per practice complete in all respect.Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . 100 mm dia |
| 292 | Supplying and fixing cylindrical air vessel of continuous welded construction fixed at riser top made of 250 mm dia, fabricated out of 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia drain valve,release valve,safety valve pressure gauge with required accessories and painting with two coats of Red Oxide and two coat of post office red enamel paint as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 293 | Supplying and Fixing of Y type strainer fabricated out of cast iron/steel body, strainer shall have 1.6 mm. thick stainless steel sheetperforated screen with 3 mm. dia holes with flange at both endscomplete with nuts, bolts, washers, gaskets etc of following sizes.complete in all respect. Appropriate Test Certificate/ report ofproduct/accessories from OEM shall be submitted. All as per preapproved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached withthis BSR .100 mm dia |
| 294 | Supply, installation, testing and commissioning of dual plate nonreturn valve (PN-16) of following sizes confirming to IS:5312 -1975complete with flanges,rubber gasket, nut,bolts, washers etc.complete in all respect. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work ,refer Annexure \"A\" attached with this BSR .100mm dia |
| 295 | Supplying, fixing, testing commissioning of butterfly valve (PN 16)with Bronze/ Gunmetal seat duly ISI marked conforming to IS13095-1991 complete with flanges,Nuts, Bolts, washers, gaskets offollowing sizes as required complete in all respect. Appropriate TestCertificate/ report of product/accessories from OEM shall besubmitted.All as per pre approved by Engineer in charge. Foradditional technical parameters of products/ work , refer Annexure\"A\" attached with this BSR 100mmdia |
| 296 | Providing, Fixing, Testing & Commissioning of single headed obliguepattern hydrant landing valve (internal/external) ISI markedconfirming to IS:5290-1983 (Type-A) /IS: 908 - 1975 with 80 mm diaflanged inlet & 63 mm dia instantaneous type female outlet couplingwith cast iron wheel complete with cap and chain, twist release typeplug and all accessories complete in all respect. Appropriate TestCertificate/ report of product/accessories from OEM shall besubmitted.All as per pre approved by Engineer in charge. Foradditional technical parameters of products/ work , refer Annexure\"A\" attached with this BSR . E242202 Gun Metal material |
| 297 | Supplying and fixing of Non-percolating flexible hose (RRL type-A)ISI marked confirming to IS:636, 63 mm dia, 15 mtr. Long RRL hosepipe with instanteneous type 63 mm dia male and female couplings(Confirming to IS:903) duly bound and riveted to hose pipes withcopper rivets and copper wire etc. as required complete in allrespect. Appropriate Test Certificate/ report of product/accessoriesfrom OEM shall be submitted. All as per pre approved by Engineerin charge. For additional technical parameters of products/ work ,refer Annexure \"A\" attached with this BSR . E242402 With Gun Metal Coupling |
| 298 | Supplying & fixing Short Branch Pipe with Nozzle ISI markedconforming to IS: 903, made of following material , fitted with 20mm(nominal internal diameter) bore nozzle, for projecting water in formof solid jet. The Branch shall have 63mm Male Instantaneous Inlet,suitable for use with 63 mm size Fire fighting hoses. H.P. tested to21 kgf/cm² for 2.5 minutes complete in all respect. Appropriate TestCertificate/ report of product/accessories from OEM shall besubmitted. All as per pre approved by Engineer in charge. Foradditional technical parameters of products/ work , refer Annexure\"A\" attached with this BSR . E242502 Gun Metal material |
| 299 | Supplying and fixing Fire Brigade In let Connection of CI body withGun Metal/stainless steel male instantaneous inlet couplingscomplete with PVC blank cap and chain as required for 150mm diaMS pipe connection, conforming to IS 903 as required of followingway :- complete in all respect. Appropriate Test Certificate/ report ofproduct/accessories from OEM shall be submitted. All as per preapproved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached withthis BSR .3 Way |
| 300 | Providing and fixing of Gun Metal/stainless steel Fire brigadeSuction hose coupling (draw out connection) with nut for femalecoupling as per IS:902-1974 complete with 100mm dia valve,complete with nut bolts and rubber insertion complete as requiredcomplete in all respect. Appropriate Test Certificate/ report ofproduct/accessories from OEM shall be submitted.All as per preapproved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached withthis BSR .. |
| 301 | Providing & fixing of size 0.9 M wide x 1.8 M height Indoor HoseCabinet shutter suitable for accomodating hydrants made ofTubular rectangular pipe (50X25mm) having central opening 6mmthick glass glazed door having necessary locking arrangement,painting (one coat primer & two coats of paint) suitable for housing 2Nos. RRL hose pipe, 1 no branch pipe, first Aid hose Reel etc . asrequired complete in all respect. All as per pre approved by Engineerin charge. For additional technical parameters of products/ work ,refer Annexure \"A\" attached with this BSR |
| 302 | Supply & Fixing of Fire Man\"s Axe with heavy Insulated rubber tested up to 20 KV and confirming to IS ;926 |
| 303 | SITC Addressable analogue Opticaltype Smoke Detector with mounting base, two LED\"s etc. as required. |
| 304 | SITC of Fault isolation module to electrically isolate different sections of detector loops. |
| 305 | SITC of microprocessor based 2 - wire loop (each loop accessing 90 addressable units ) Fire Alarm Control Panel. The Panel shall be able to give pin point location of addressable units via the address code for each unit. The Panel shall also be able to automatically switch off all control switches when-ever any Alarm is triggered. The Panel shall also be able to give voice announcement to individualized speakers. The Panel shall have built in sounder, Maintenance Free Batteries of minimum 15 Ah of 24 volts capable of minimum of 12 hours with battery charger, rectifier. Loop cards, LCD unit to indicate Fire / Fault Signal of individual unit, built in-built / external printer, to log all incoming data etc complete in all respect. 2 - Loop |
| 306 | SITC of conventional type Manual call point complete with Glass, hammer and chain etc. as required. |
| 307 | Supply & FixingISI marked (IS:10204) Poratable Fire Exitnguisher,Trolleymounted Mech. Foam type capacity09 ltrs withgun-metalcapandnozzleandcompleterespectsinall respects includinginitial fill and wall suspension. |
| 308 | Carbon Dioxide type fire extinguisher with cylinder fully charge of 4.5kg capacity. |
| 309 | Providing and fixing charged ABC type fire extingusher including thecost of fixing with nut, bolts etc as required. 5 kg |
| 310 | Providing, fixing, testing & commissioning of sprinkler heads of the following type : Pendant type with quartziod bulb, operating temperature at 68 deg C as per specifications. |
| 311 | Providing, installation, testing and commissioning of dual plate non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, G I bolts, nuts, washers etc. as required.a) 150 mmdia |
| 312 | Supplying, fixing, testing commissioning of butterfly valve PN 1.6, with Bronze/ Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS 13095, of following sizes as required.a)80 mm dia |
| 313 | b) 150mm dia |
| 314 | c) 200mm dia |
| 315 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required. 2 x 1.5 sq.mm |
| 316 | Providing, laying, testing & Commissioning of\"C\" class heavy duty MS pipe conforming to IS 3589 and 1239 for hydrent and sprinkler underground rings including all accessories such as screwed/ welded flanges, tees, reducers etc. Conforming to IS : 1239/3589 complete including , welding, jointing with compressed asbestos gaskets, nuts, bolts etc. as required.with cleaning,wrapping and coating of the pipe with 4 mm thick tar based plymaric corrosion protection tape or equivalent including applying uniform coat of cold pipekot primer as per IS; 10221 for protection against corrsionsuitable for allkind of soil at 1.0 M depth including excavationand making good the same as requiredat site . a) 150 mm dia |
| 317 | SITC ofLocal fire authority approved Horizontalsingle stage Jockey pump with CI Body, Bronze impellor, SS shaft, mechanical seal coupled with Squirrel cage induction motor for automatic operationsuitable for three phase, 415 V, 50 Hz AC supply with synchronous speed of 2900 RPM ,T.E.F.C type confirming to IP:55 with flexible coupling and coupling guard with the pump ,Common bed platefabricatedfrom mild steel channel , Suitable cement concreat foundation duly plastered with anti vibration pads. a) 180 LPM suitable for 56 Mtr |
| 318 | Providing, installation, testing and commissioning of dual plate non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, G I bolts, nuts, washers etc. as required. a) 80 mm dia |
| 319 | b) 200 mm dia |
| 320 | S&F following sizes of ISI marked steel conduit alon with heavy duty accessories in surface /recessed using saddles, clamps, fasteners as required including cutting the wall and making good the same as required. 20 mm |
| 321 | 25 mm |
| 322 | Providing & Laying XLPE insulated / P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor Armoured of IS:7098-I/1554-1 approved make in ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second Class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. 16.0 Sq.mm 4 core |
| 323 | 35.0 Sq.mm 3.5 core |
| 324 | 240.0 Sq.mm 3.5 core |
| 325 | Supplying and making one end termination with heavy duty double compression brass gland SIBG type, heavy duty copper lugs duly crimped with crimping tool, PVC tape etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size.4 x 16.0 sq.mm |
| 326 | 3.5 x 35.0 sq.mm |
| 327 | 3.5 x 240.0 sq.mm |
| 328 | Maintenance free gel earthing with pipe in pipe /Strip in Pipe technology filled with anti corrosive conductive compound (CPRI tested) below the ground in 150 -200 mm dia earth pit and surrounding filled with required mineral filling compound (MFC should have hygroscopic proper ty to retain the moisture for long time to create low resistance Zone) and C.C. finished chamber covered with hinge type with locking arrangement C.I cover. C.I. frame of size 300mm x300mm complete testing of earth resistance as required of following sizes With pipe in pipe technology (inner pipe dia / outer pipe dia) 80 -100 micron G.I. coating With pipe in pipe technology with 80-100 micron G.I. coatingG.I. pipe 2000 mm long , 63/80 mm , inner strip 50 mmx 3mmcopper |
| 329 | S & Laying following size earth wire/strip in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. as required. 8 SWG copper Wire |
| 330 | 25mm x 3mm copper strip |
| 331 | S & Laying following size ‘B’ Class G.I. Pipe confirming to IS: 1239P-1 (1990) with accessories for laying earth conductor/ strip/ cable inground/ surface/ recess as required. 100mm dia.. |
| 332 | Providing and laying ISI marked P.V.C. insulated submersible cable confirming to IS:694 with flexible copper conductor including making connection etc. as required 4.0 Sq.mm 3 core flat |
AI Tender Summary
Tender Timeline
Sep 09, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedOct 03, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 04, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender