Tender For Conversion Of Existing Kitchen Into Modular Kitchen I/C Other Interior Decoration Works, Iei And Construction Of 01 No. Free Standing Pergola Structure, 01 No. Garden House Structure At Dc Camp Office Cum Residence At Deopur, Mayabunder Un
Tender Value
23.96 Lakhs
Estimated cost
Bid Submission
18 Sep 2023
0 days left
EMD
47923
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
mayabunder → Andaman And Nicobar Islands
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Conversion Of Existing Kitchen Into Modular Kitchen I / C Other Interior Decoration Works, Iei And Construction Of 01 No. Free Standing Pergola Structure, 01 No. Garden House Structure At Dc Camp Office Cum Residence At Deopur, Mayabunder Under Sub Div
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | All kinds of soil. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 4 | 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 5 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 7 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 8 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 10 | Foundations, footings, bases of columns, etc. for mass concrete |
| 11 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 12 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 14 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 15 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. |
| 16 | Granite stone slab of colour black, Cherry/Ruby redi) Area of slab over 0.50 sqm |
| 17 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 18 | Granite work |
| 19 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 20 | Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.(Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 21 | Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 22 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 23 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 24 | Electric resistance or induction butt welded tubes |
| 25 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
| 26 | Providing and fixing bolts including nuts and washers complete. |
| 27 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 28 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 29 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). |
| 30 | Light shade pigment using white cement |
| 31 | 12 mm cement plaster of mix : |
| 32 | 1:4 (1 cement: 4 fine sand) |
| 33 | 1:6 (1 cement: 6 fine sand) |
| 34 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification. |
| 35 | Two or more coats on new work |
| 36 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : |
| 37 | Water thinnable cement primer |
| 38 | Finishing walls with Acrylic Smooth exterior paint of required shade : |
| 39 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 40 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 41 | Two or more coats on new work |
| 42 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : |
| 43 | Two or more coats on new work |
| 44 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 45 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 46 | Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in-Charge. |
| 47 | For door/ window/ clerestory window |
| 48 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 49 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 50 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 51 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 52 | Of area 3 sq. metres and below |
| 53 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 54 | For thickness of tiles above 25 mm and up to 40 mm |
| 55 | Providing and laying matt finished vitrified tile of size 300x300x9.8mmhaving with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoorfloors such as footpath, court yard, multi modals location etc., laidon 20mm thick base of cement mortar 1:4 (1 cement : 4 coarsesand) in all shapes & patterns including grouting the joints with whitecement mixed with matching pigments etc. complete as per directionof Engineer-in-Charge. |
| 56 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 57 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 58 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. |
| 59 | Upto 5mm depth and 5 mm width |
| 60 | Providing, erecting, maintaining and removing temporary protective screens made out of specified fabric with all necessary fixing arrangement to ensure that it remains in position for the work duration as required by the Engineer-in-charge. |
| 61 | Wooven PVC cloth |
| 62 | Dismantling tile work in wall laid in cement mortar including stacking material within 50 metres lead.a)For thickness of tiles 10 mm to 25 mm |
| 63 | Providing and laying hollow block cement concrete block walling 100mm thick consisting of hollow block of size 400mm x 100mm x 200mm of mix 1:3:6 (1 cement; 3 coarse sand; 6 graded stone aggregate 10mm nominal size) having a crushing strength of 3.5N/Sqm at 20 days as per IS:2185 (Part-I) 1979 laid in cement mortar 1:6 (1 cement; 6 coarse sand) upto floor five level. |
| 64 | Providing and laying hollow block cement concrete block walling 200mm thick consisting of hollow block of size 400mm x 200mm x 200mm of mix 1:3:6 (1 cement; 3 coarse sand; 6 graded stone aggregate 10mm nominal size) having a crushing strength of 3.5 N/Sqm at 28 days as per IS:2185 (Part-I) 1979 laid in cement mortar 1:6 (1 cement; 6 coarse sand) upto floor five level. |
| 65 | Providing & fixing bottom cabinets of different carcass sizes made of 18mm thick Pre-laminated HDF Boards (of Green Ply or equivalent)in partitions, Front Face panels & back boards of 12mm thick pre-laminated HDF Boards ,each cabinet units consisting of required number of SS 304 Grade modular kitchen wire baskets as required a) 1st cabinets unit comprising of Top drawer for perforated cutlery baskets (4inches ht), Middle drawer for partition baskets (4inches ht) & Bottom most drawer for Thali/Plate baskets (8inches ht).b) 2nd Cabinet Unit comprising of Top drawer for Cup & Saucer baskets (6inches ht), Middle & Bottom most drawers for plane baskets (6inches ht) respectively.Including with a set of necessary soft close SS Telescopic channels 22\" (Depth), Soft close SS Quadrail Channels of 22\" Depth, SS Screws of required sizes, Golden Finish -G Profile Handles of Suitable Size in each drawers of cabinet unit,Adhesives etc all complete as per enclosed drawing & the directions of EIC. Note :-(Only Front Face of cabinet unit shall be measured for payment Purpose & All hinges, channels i/c wire baskets above used shall be of Hettich brand or equivalent). |
| 66 | Providing & Fixing Floating Shelves of 20cm wall projection made of 18mm thick Pre-laminated HDF boards (of Green Ply or equivalent) in shelves, backingi/c all fixing withnecessary Stainless Steel Screws, nails, adhesives etc. all complete as per the direction of EIC.(Measurementto be paid for front face in sqm as per the drawing enclosed.) |
| 67 | Providing & fixing bottom cabinets of required carcass sizes made of 18mm thick Pre-laminated HDF Boards (of Green Ply or equivalent)in partitions, Table top & back boards , consisting of 03Nos of Wicker baskets as required a) Cabinet Unit Comprising of Top drawer for Plane wickerbaskets of 23\"\" width, 20\" Depth,4\" Height , Middle drawer for Plane wickerbaskets of 23\"\" width, 20\" Depth,6\" Height ,Bottom most drawer for Plane wickerbaskets of 23\"\" width, 20\" Depth,6\" Height all completeincluding fixing with necessary clamps, Stainless Steel Screws, Set of Side Sliding Channels 22\"\" Depth & other accessories etc wherever required all complete as per enclosed drawing & the directions of EIC. (Only Front Face of Wicker Cabinet unit shall be measured for payment Purpose.)(All Sliding channels, framesi/c wicker baskets above used shall be of Hettich brand or equivalent). |
| 68 | Providing & Fixing bottom cabinets of required dimensions for working slab area of kitchen , all made of 18mm thick Pre-laminated HDF boards (of Green Ply or equivalent) in partitions,table top,Bottom, Shelves, front face shutter panels & back boards 12mm thick pre-laminated HDF board without inner shelvesi/c all fixing withnecessary Stainless Steel Screws, Stainless Steel Soft Close Hinges (Size 0 degree), Golden Finish -G Profile Handles of Suitable Size, nails, adhesives etc. all complete as per the direction of EIC.(Measurementto be paid for front face in sqm as per the drawing enclosed.) |
| 69 | Providing & Fixing bottom cabinets of required dimensions below the kitchen working slab , all made of 18mm thick Pre-laminated HDF boards (of Green Ply or equivalent) in partitions, front face shutter panels, racks, i/c all fixing withnecessary Stainless Steel Screws, Stainless Steel Soft Close Hinges (Size 0 degree), Golden Finish -G Profile Handles of Suitable Size , nails, adhesives etc. all complete as per the direction of EIC.(Measurementto be paid for front face in sqm as per the drawing enclosed.) |
| 70 | Providing & Fixing bottom cabinets of required dimensions below the kitchen working slab , all made of 18mm thick Pre-laminated HDF boards (of Green Ply or equivalent) in partitions, front face shutter panels but without racks, i/c all fixing withnecessary Stainless Steel Screws, Stainless Steel Soft Close Hinges (Size 0 degree), Golden Finish -G Profile Handles of Suitable Size , nails, adhesives etc. all complete as per the direction of EIC.(Measurementto be paid for front face in sqm as per the drawing enclosed.) |
| 71 | Providing & Fixing wall mounted top cabinet with 33cm projection &other required dimensions of width & height (as per the drawing enclosed) above the Kitchen working slab with required racks, Sides, rear side board including fixing with Top Hung Fully Glazedshutters in the cabinet ,all made of 18mm thick Pre-Laminated HDF Boards (of Green Ply or equivalent) using 4mm thick glass panes in the glazed shutter, 12mm thick HDF Boards in the rear sides, i/c Stainless Steel screws,Stainless Steel Hydraulic Soccer of 12Kg Capacity,Stainless Steel Soft close Hinges (Size - 0 -Degree), Golden Finish -G Profile Handles of Suitable Size , Nails, Adhesives, etc. all complete as per the direction of EIC. (Measurementto be paid for front face in sqm as per the drawing enclosed).(Hinges, Channels, soccers above used shall be of Hettich brand or equivalent) |
| 72 | Providing & Fixing wall mounted top cabinet with 33cm projection &other required dimensions of width & height (as per the drawing enclosed) above the Kitchen working slab with required racks, Sides, rear side board including fixing with openable Fully Glazedshutters in the cabinet ,all made of 18mm thick Pre-Laminated HDF Boards (of Green Ply or equivalent) using 4mm thick glass panes in the glazed shutter, 12mm thick HDF Boards in the rear sides, i/c Stainless Steel screws,Stainless Steel Soft close Hinges (Size - 0 -Degree), Golden Finish -G Profile Handles of Suitable Size , Nails, Adhesives, etc. all complete as per the direction of EIC. (Measurementto be paid for front face in sqm as per the drawing enclosed).(Hinges, Channels, G Profiles above used shall be of Hettich brand or equivalent). |
| 73 | Providing & fixing top cabinet for GTPT (Glass Tray Plate Tray) of required size above the kitchen working slab,with openable shutters, Sides, top, bottom of the cabinet unit all made of 18mm thick Pre-Laminated HDF Boards (of Green Ply or equivalent) , 12mm thick Pre-Laminated HDF Boards in rear sides backing, Fixing of SS 304 Grade Glass &plate with drip tray set of 03Pieces inside the cabinet unit (as per the enclosed drawing) including necessary soft close auto hinges (0 Degree), SS Cleats, Adhesives, Golden Finish -G Profile Handles of Suitable Sizein the shutters of cabinet unit, etc wherever required all complete as per enclosed drawing & the directions of EIC. (Only Front Face of cabinet unit shall be measured for payment Purpose.)(Above used hinges, baskets shall be of Hettich brand or equivalent) |
| 74 | Providing & Fixing wall mounted top cabinet with 33cm projection &other required dimensions of width & height (as per the drawing enclosed) above the Kitchen working slab with required racks, Sides, rear side backing boards including fixing with openableshutters in the cabinet ,all made of 18mm thick Pre-Laminated HDF Boards (of Green Ply or equivalent) , 12mm thick HDF Boards in the rear side backing, i/c Stainless Steel screws,Stainless Steel Soft close Hinges (Size - 0 -Degree), Golden Finish -G Profile Handles of Suitable Size , Nails, Adhesives, etc. all complete as per the direction of EIC. (Measurementto be paid for front face in sqm as per the drawing enclosed).(Hinges, Channels, G profile handles above used shall be of Hettich brand or equivalent). |
| 75 | Providing & Fixing Tall Open Cabinet for Fridge Storage with 60-70cm wall projection,width & height dimensions as required (to suit the actualfridge size)with Sides & top covered, rear side backing boards ,all made of 18mm thick Pre-Laminated HDF Boards (of Green Ply or equivalent) , 12mm thick HDF Boards in the rear side backing, i/c Stainless Steel screws, Nails, Adhesives, etc. all complete as per the direction of EIC. (Measurementto be paid for front face in sqm as per the drawing enclosed). |
| 76 | Providing & Fixing Tall Pantry Unit of Size 1.20m (L) x 0.60m (W) x 1.80m (H) with double door storage features, Sides & top covered, rear side backing boards, Partitions ,all made of 18mm thick Pre-Laminated HDF Boards (of Green Ply or equivalent) , 12mm thick HDF Boards in the rear side backing,i/c pantry unit consisting of 24 basketsi/c Stainless Steel screws, Golden Finish -G Profile Handles of Suitable Size, Stainless Steel Soft close Hinges (Size - 0 -Degree),Nails, Adhesives, etc. all complete as per the direction of EIC. (Measurementto be paid for front face in sqm as per the drawing enclosed). |
| 77 | Providing and fixing Stainless Steel 304 Grade kitchen Sink of Satin finish & Single bowl as per IS:13983 with necessary brackets and stainless steel plug 40 mm, includingcutting and making good the walls wherever required :all complete as per the direction of EIC. (Of Crocodile or Equivalent) |
| 78 | Of Size - 800mm (W) x 500mm (D) x 250mm (H) |
| 79 | Providing and fixing acrylic oval glass shelf of Size 18 inches (L) with edges round off, fixed with 40 mm long screws, rawl plugs etc., all complete as per the directions of EIC.(Of Jaguar or equivalent). |
| 80 | Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thickgalvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extrudedglazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 81 | Fixed window / ventilator made of (small series) frame 67 x 60 mm & mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm andsingle glazing beadof appropriate dimension. (Area of window above 2.10sqm upto 6.00Sqm) |
| 82 | Providing & Fixing GI wire mesh 25 x 25mm Size over the existing steel frame works in the outer side walls of pet animal shed using GI binding wires etc. all complete as per the directions of EIC. |
| 83 | Supplying and filling in plinth with pulverised sand under floors, including watering, ramming, consolidating and dressing complete. |
| 84 | Providing and fixing 1.35mm thick Polycarbonate Solid Sheets/ PC embossed Sheet of LEXAN brand or equivalent & suitable colour.The sheet shall be fixed upto any pitch of required curvature as per the architectural drawings using Aluminium H profiles (dome section) and SS Self drilling screws complete.The work includes cutting to the size and curvature shape wherever required, leak proofing the joints with sealant material and excludes the cost of truss work etc. all complete as per the directions of EIC.(Aluminium H Profiles/ dome section with screws shall be paid separately.) |
| 85 | Providing and fixing aluminium H Profiles (Dome Section) with EPDM rubber gasket for connecting two polycarbonate sheets together including self tapping SS Screws of suitable size etcall complete as per the directions of EIC. |
| 86 | Providing cement concrete surface drain including earthwork in excavation, 10 cm thick base concrete and 15 cm thick side walling with 1:3:6 (1 cement ; 3 coarse sand; 6 graded stone aggregate 40 mm nominal size ) finishing with 1:4 ( 1 cement : 4 including 40 mm thick cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) with a floating coat of neat cement, including cement slurry complete in its floor, top and exposed surface including earth work in excavation and disposal of surplus earth etc. complete. |
| 87 | 23x23 cm surface drain. |
| 88 | Manufacturing and Fixing partition design walls of required size & approved design pattern built up with various box made sections such as 50x150mm in framing beams and 50x200mm in Rectangular/Circular/Diamond Shelves all made of 18mm thick HDF boards (of Green Ply or equivalent) without laminations, pasted with 1.5mm thick sunmica sheet in external portions of partition wall members including necessary adhesives, nails,screws etc. wherever required all complete as per enclosed drawing & the directions of EIC. |
| 89 | Providing and Fixing decorative panellings in the beam projections as per approved design & patterns using 18mm thick HDF boards (Of Green Ply or equivalent) without laminations pasted with 1.00mm thick Glossy finish sunmica sheets in its exposed strips including necessary adhesives, nails,screws etc. wherever required all complete as per enclosed drawing & the directions of EIC. Beam panelling shall be formed by fixing 80mm wide strips with intermediate gap of 25mm in an alternative manner.The intermediate gap of 25mm will acts as Groove like Finish. |
| 90 | Providing and Fixing decorative Claddings in the Column projections as per approved design & patterns using 18mm thick HDF boards (Of Green Ply or equivalent) without laminations pasted with 1.00mm thick Glossy finish sunmica sheets in its exposed strips including necessary adhesives, nails,screws etc. wherever required all complete as per enclosed drawing & the directions of EIC.Column Cladding shall be made by fixing 20cm height panels with intermediate gap of 25mm in an alternative manner.The intermediate gap of 25mm will acts as Groove like Finish. |
| 91 | Providing and Fixing a curtain wall as per approved design & patterns using 18mm thick HDF boards (Of Green Ply or equivalent) without laminations in its framing work pasted with 1.00mm thick Glossy finish sunmica sheets in its exposed surface and fixing 18mm thick PVC readymade Jali cut with approved design in the panelling of Curtain Wallincluding necessary adhesives, nails,screws etc. wherever required all complete as per enclosed drawing & the directions of EIC. |
| 92 | Providing and Fixing Rhombus pattern- Rectangular wall mirror having edges polished of suitable & required size fixed on 12mm thick plain HDF boards (Green Ply or Equivalent) i/c backing frames (40x18mm) with 18mm thick HDF boards, setting & fixing the wall mirror using mirror mounted tapes (double sided tapes) to the specified height with accurate plumbline and pasting the exposed edges of HDF board backing frames with 1.00mm thick Glossy finish sunmica sheets (Green ply or equivalent) including necessary adhesives, nails,screws etc. wherever required all complete as per enclosed drawing & the directions of EIC. |
| 93 | Providing and Fixing bottom cabinets with dimensions of 600mm depth,50cm height and required length below the partition design wall, all made of 18mm thick HDF boards (Of Green Ply or equivalent) in partitions, front face shutter panels, racks, backing and table top and pasted with 1.00mm thickglossy finish Sunmica Sheets in its exposed edges including all fixing withnecessary Stainless Steel Screws, Stainless Steel Soft Close Hinges (Size 0 degree), Golden Finish -G Profile Handles of Suitable Size , nails, adhesives etc. all complete as per the direction of EIC.(Measurementto be paid for front face in sqm as per the drawing enclosed.) |
| 94 | Providing and fixing 18 mm thick, 150 mm wide pelmet of 1st class padauk wood including top cover of 12mm 1st class padauk wood planks, nickel plated M.S. pipe 20 mm dia ( heavy type ) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm longand rawl plugs 50 mm long etc. all complete |
| 95 | Providing & Pasting high quality decorative wall papers of approved design & colour shades over the interior masonry wall surfaces including its necessary cuttings as per the wall texture & other required accessories etc all complete as per the directions of EIC. |
| 96 | Melamine polishing (Matt finish) on new work by scrapping & removing the deposits in wood works with grinding machine cleaning the wood with natural culour and smoothining the surface with sand paper of different size & applying melamine polish (Matt finish) comprising of two coats of pillar & rubbing with water paper & drying filler for 6 to 8 hours, applying two coats sealer and rubbing with water paper applying two coats of melamine polish etc. complete. |
| 97 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor singlecorecableinsurface /recessedmediumclassPVC conduit, with modular switch, modular plate, suitable GI box and earthingthepointwith 1.5sq.mm FRLSPVC insulated copper conductor single core cable etc. as required. |
| 98 | Group A |
| 99 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 100 | 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 101 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 102 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 103 | 5/6 A switch |
| 104 | Supplying and fixingtwo module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 105 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 106 | 8 Module (125mmX125mm) |
| 107 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 108 | Supplying and fixing 3pin, 5A ceiling rose on the existing junctionbox/woodenblockincludingconnectionsetc.as required. |
| 109 | Installation ,Testing,Commissioningofwallbracket/ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lampsperfitting,completewithallaccessoriesincluding connections etc. as required. |
| 110 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required. |
| 111 | Supplying, installation, testing and commissioning of brand new wall mounted Angular Suction and Auto Clean Designer Series Electric Chimney having features suction capacity 1100 Cum/ Hour for a size of 90cm (for burner stove) including ducting kit equivalent to make FABAR HOOD ALPHA HC PB BK 90 SKU code 325.0676.564 complete or its equivalent to BOSCH, GLEN, Hindware, Kaff etc. as required complete. |
| 112 | Supplying of 3 W LED recessed mounted adjustable focused spot light (tilt option) strong focused beam (36 beam) tilt angle of 25 metal heat sink for aurable performance equivalent to PHILIPS ASTRA SPOT COB3W Tilt light Cat No.91921850766PK1 or its equivalent to ISI standard of make Havells / Crompton / Bajaj / Polycab etc. as required complete. |
| 113 | Supplying of 12 LED recessed mounted Downlight Minmalistic outer trim & deep recessed COB focused 36 degree beam angle having metal housing for longer life with 35000 hours life no harmful UV radiation, CRI>80 equivalent to PHILIPS DECO COBLED Spot Light 12W or its equivalent to ISI standard of make Havells / Crompton / Bajaj / Polycab etc. as required complete. |
| 114 | Supplying of 6W 1 feet LED recessed mounted Linear under cabinet, wardrobes, kitchen spaces lighting having lumens of 6W-420lm with CRI>80 equivalent to PHILIPS 6W 1ft space gow Linear LED light (WW) or its equivalent to ISI standard of make Havells / Crompton / Bajaj / Polycab etc. as required complete. |
| 115 | Supplying of 12W 2feet LED recessed mounted Linear under cabinet, wardrobes, kitchen spaces lighting having lumens of 12W-900lm with CRI>80 equivalent to PHILIPS 12W 2ft space gow Linear LED light (WW) or its equivalent to ISI standard of make Havells / Crompton / Bajaj / Polycab etc. as required complete. |
| 116 | Supplying of Energy efficiency BLDC ceiling fan of white in colour without remote control of 1200mm sweep, suitable for operation on 230 volts, single phase, 50Hz, AC supply including 30cm long down rod etc. as required equivalent to Havells Efficiencia Neo (BLDC 26 W) without remote or its equivalent to ISI specifications. |
AI Tender Summary
Tender Timeline
Sep 04, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedSep 18, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedSep 19, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender