Indian Institute Of Technology-IITB has published Tender For Creation Of Office Space For Catalyst Staff In Tih And Catalyst Building At Lp-1 In North Campus Of Iit Mandi. Submission Date for this Tender is 08-09-2023. Civil Work Tenders in mandi Himachal Pradesh. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 2 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 4 | Centering and shuttering including strutting, propping etc. and removal of form work for: Foundations, footings, bases for columns as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 5 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 11 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 12 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 13 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 14 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level, Concrete of M25 grade with minimum cement content of 330 kg /cum as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 15 | Add for using extra cement in the items of design mix over and above the specified cement content therein as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 16 | Brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 17 | Half brick masonry with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement:3 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 18 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 19 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 20 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 21 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 22 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 23 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 24 | Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade : Old work (one or more coats) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 25 | Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (One or more coat applied @ 0.90 ltr/10 sqm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 26 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 27 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 28 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 29 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, Area of slab over 0.50 sqm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 30 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 31 | Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 32 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 33 | Providing and laying at or near ground level factory made kerb stoneof M-25 grade cement concrete in position to the required line, leveland curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 34 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 35 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 36 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 37 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 38 | Providing and fixing S S 304 grade double shed glass door lock glass to glass 100mm padlockfor Fully glazzed door including necessary cutting, hole, fixing accessories and making good etc. all complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 39 | Providing and fixing S S 304 grade door handle set for fully glazzed door including necessary cutting, hole, fixing accessories and making good etc. all complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 40 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With brass cover plate minimum 1.25 mm thickness as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 41 | Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 42 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps atjunctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / pC.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) : For fixed portion, Powder coated aluminium (minimum thickness of powder coating 50 micron) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 43 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 44 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 45 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 46 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc .complete as per the architectural drawings and the directions of Engineer-in-Charge.(Cost of aluminium snap beading shall be paid in basic item): With frost glass panes of 5.00 mm thickness complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 47 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 48 | Providing and fixing aluminium handles, ISI marked, powder coated (coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. 200mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 49 | Providing and fixing aluminium handles, ISI marked, Powder coated aluminium (minimum thickness of powder coating 50 micron) transparent or dyed to required colour or shade, with necessary screws etc. complete. 100 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 50 | Providing and fixing aluminium tower bolts, ISI marked, powder coated (coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.200 x 10 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 51 | Providing and fixing aluminium tower bolts, ISI marked, powder coated (coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. 150 x 10 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 52 | Providing and fixing bright finished brass hard drawn hooks and eyes : 300 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 53 | Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 54 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 55 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 56 | P/F dash fastner /chemical fastner for frame work as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 57 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall, 25 mm dia nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 58 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall, 15 mm dia nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 59 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 60 | Providing and fixing brass stop cock of approved quality : 15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 61 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): 25 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 62 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): 15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 63 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 64 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 65 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler, 75 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 66 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler, 110 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 67 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°, 75 mm bend as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 68 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°, 110 mm bend as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 69 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door, 75x75x75 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 70 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door, 110x110x110 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 71 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door, 75x75x75 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 72 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door, 110x110x110 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 73 | Providing and fixing Nahani Trap 75mm x 110mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 74 | Providing and fixing Stainless steel jalli as as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 75 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, 15 mm dia CP Brass single hole sink mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board, 510x1040 mm bowl depth 250 mmas per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 76 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe, 32 mm dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 77 | Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length, 15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 78 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 79 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 80 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 81 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 82 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type, With common burnt clay F.P.S. (non-modular) bricks ofclass designation 7.5 as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 83 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 84 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colourweighing not less than 88 gmsas per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 85 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 86 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gmsas per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 87 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 88 | Providing and fixing toilet paper holder : C.P. brass as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 89 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers completeas per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 90 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 91 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: 25 to 40 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 92 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250 mm diameter as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 93 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 94 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 95 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 15 mm nominal bore as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 96 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm ofcement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCCslab including adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishingthe surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 97 | Crazy ceramic tile flooring, with under layer 12 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), with joints not exceeding 5 mm, including filling the gaps with ordinary cement mixture & mixing with synthetic polyester fibre, triangular in shape having specific gravity of 1.34 to 1.40, cross section size ranging from 10 to 40 micron & length upto 6 mm , mixing fibre @ 125 grams per 50 kg of cement in cement mortar, including providing and mixing water proofing material in mortar @ 1 kg per 50 kg of cement, all complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 98 | Electrical items POINT WIRING & SUBMAIN WIRING WIRING IN PVC CONDUIT Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 99 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 100 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 101 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 102 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 103 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 4 sq. mm + 2 X 4 sq. mm earth wire as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 104 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 6 X 2.5 sq. mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 105 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 6 X 4 sq. mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 106 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 107 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 108 | Supplying and fixing 3 Module Modular base & cover plate on existing modular metal boxes etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 109 | Supplying and fixing 6 Module Modular base & cover plate on existing modular metal boxes etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 110 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 111 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 112 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 113 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting/LED Fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 114 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 115 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 116 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 117 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 118 | MCCB, MCB & DB’S Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator) 8 way (8 + 24), Double door as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 119 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator) 12 way (8 + 36), Double door as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 120 | Supplying and fixing 5A to 32A Rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 121 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 122 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 123 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 124 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 125 | Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. For 8 way, Double door TPN MCBDB as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 126 | Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 127 | MV CABLE LAYING Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering. Upto 35 sq. mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 128 | Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering Upto 35 sq. mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 129 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 130 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 131 | Supplying and making end termination with brass compression gland and Cu lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 4 X 6 sq. mm (19mm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 132 | Supplying and making end termination with brass compression gland and Cu lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 4 X 16 sq. mm (28mm) as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 133 | Supplying of Square Surface Down Lighter (2 X 2) of Wattage 36 W (6500K) with electronic driver etc. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 134 | Supplying of Surface mounted Downlight with Aluminium (99% Purity) Sink, available in Round shape. PC diffuser in white powder coated finish with built in electronic low THD (<10%) LED driver of wattage 15W, colour temprature 6000k and above , P.F > 0.90 etc.as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 135 | Supplying of 10W surface and wall mounted LED batten with aluminum housing & integrated electronic driver (592 mm) with minimum colour temperature of 6000 k , P.F > 0.9 etc.as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 136 | Supply of 1400 mm sizes ofceiling fan without regulator complete with double ball bearing, copper wound motor, blades, downrod, canopy, capacitor etc.suitable for operation on 230 V 50 Hz supply, ENERGY EFFICIENT / 3-5 STAR RATING etc asper entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. . |
| 137 | Supply of PVC Fresh Air Exhaust Fan Sweep 25 cm (250 mm) ,Air Delivery 813 m3/hr, Speed 1250 rpm, Power Input 45 W, suitable for operation on 230 V 50 Hz supply, etc asper entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 138 | Supply, Installation, testing & commissioning of following capacity of electrical water heaters with connection pipes & top plugs etc as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. 25 Ltr. Capacity asper entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 139 | Supplying of cables of following size of PVC insulated and PVC sheathed / XLPE Copper conductor round wired armoured cable of 1.1 kV grade as required. 4C X 6 sq. mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 140 | Supplying of cables of following size of PVC insulated and PVC sheathed / XLPE Copper conductor round wired armoured cable of 1.1 kV grade as required. 4C X 16 sq.mm as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 141 | Supplying and fixing 3 Module PVC box to be fixed on Recess or in Open Surface as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 142 | Supplying and fixing 6 Module PVC box to be fixed on Recess or in Open Surface as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 143 | Supplying and fixing of Support for mounting wiring accessories equipped with Arteor socket outlets Clip-on supports which can be fitted side by side Supplied with finishing plate of 3 module - for 65 mm cover as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 144 | Supplying and fixing of Support for mounting wiring accessories equipped with Arteor socket outlets Clip-on supports which can be fitted side by side Supplied with finishing plate of 6 module - for 65 mm cover as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 145 | Supplying and installation of following items for 3 Track PVC Trunking of Size 195X50 mm (2 X 65 + 40 mm) as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. PVC Trunking Base (195x50 mm) |
| 146 | Supplying and installation of following items for 3 Track PVC Trunking of Size 195X50 mm (2 X 65 + 40 mm) as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. Straight Cover 65 mm |
| 147 | Supplying and installation of following items for 3 Track PVC Trunking of Size 195X50 mm (2 X 65 + 40 mm) as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. Straight Cover 40 mm |
| 148 | Supplying and installation of following items for 3 Track PVC Trunking of Size 195X50 mm (2 X 65 + 40 mm) as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. Internal Corner |
| 149 | Supplying and installation of following items for 3 Track PVC Trunking of Size 195X50 mm (2 X 65 + 40 mm) as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. External Corner |
| 150 | Supplying and installation of following items for 3 Track PVC Trunking of Size 195X50 mm (2 X 65 + 40 mm) as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. End Cap |
| 151 | Supplying and installation of following items for 3 Track PVC Trunking of Size 195X50 mm (2 X 65 + 40 mm) as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. Flat Angle |
| 152 | Supplying and installation of following items for 3 Track PVC Trunking of Size 195X50 mm (2 X 65 + 40 mm) as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. Tee |
| 153 | Supplying and installation of following items for 3 Track PVC Trunking of Size 195X50 mm (2 X 65 + 40 mm) as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. Cover Joint 65 mm |
| 154 | Supplying and installation of following items for 3 Track PVC Trunking of Size 195X50 mm (2 X 65 + 40 mm) as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. Cover Joint 40 mm |
| 155 | Supplying and installation of following items for 3 Track PVC Trunking of Size 195X50 mm (2 X 65 + 40 mm) as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. Separation Partition |
| 156 | Supplying Supplying and fixing of 32 X 12 mm size of medium class PVC casing capping along with accessories including coupler, tee, elbow, internal bend, external bend etc. in surface as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 157 | Fire Fighting Supplying, installation, testing & commissioning of manual call box of ABS type in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 158 | Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 159 | Supplying, installation, testing & commissioning of main control and indicating panel made out of 16 SWG MS sheet to accommodate the following items duly powder coated in approved colour with louvers for ventilation, locking arrangement, audio and visual indication for fire alarm and public address system, monitoring system including connections, interconnections etc complete as required. 6 zone panel for fire alarm system 100 watt amplifier racks suitable for operation on 230V AC/24V DC supply conforming to IEC-268-3 complete with all accessories as required- 2 Nos.(one to act as standby)Talk back master station with LED PTT (press to talk) push button for operation on 230V AC/24 V DC supply conforming to IEC-268 for simplex mode of operation/communication suitable for 20 Nos.talk back unit -1 set. Annoucement control desk suitable for selection of different zones selectively and ON ALL CALL switch with visual indication etc., complete as required- 1 set. Amplifier change over switch for inter changing amplifier- 1 No. Monitor panel for loudspeaker complete output selector ON/OFF switch, fuse visual indications etc. complete as required- 1 No. Gooseneck microphone with stand and ON/OFF switch -1 No. Mains ON/OFF switch, fuse indication lamps, DC and AC voltmeters & ammeters terminal blocks etc. complete as required -1 set. Battery charger trickle cum boost to take complete load of fire alarm & PA system complete with all accessories including providing & fixing of 2 nos. 12 volt,30 AH each sealed maintenance free batteries -1 set as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 160 | HYDRANT SYSTEM Providing laying, testing & commissioning of "C" class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150 mm nominal dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 161 | Providing, laying, testing & commissioning of "C" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Providing, laying, testing & commissioning of "C" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm Dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 162 | Providing, laying, testing & commissioning of "C" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Providing, laying, testing & commissioning of "C" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm Dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 163 | Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 164 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm Dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 165 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm Dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 166 | Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 167 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required: 100 mm Dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 168 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm Dia as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 169 | Supplying and fixing 63 mm dia, 15 mtr. Long RRL hose pipe with 63 mm dia Male and Female ss couplings duly binded with G Iwire, rivets etc. conforming to IS 636 (type-A) as required. Gun Metal as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 170 | Providing & fixing weather proof standard hose cabinet (900 mm x 600 mm x 500 mm) made of 2 mm thick MSsheetwith 6 mm thick glazed glass door i/c necessary locking arrangement suitable to accommodate 2 nos. 15 mtr . long Hose pipe, 1 No branch pipe ,mounted onplatform/ MS Support/wall & duly power painted with post office red colour externally and white internally with synthetic enamel paint complete in all respect as required as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 171 | Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 Mtr Long as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 172 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 173 | Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 3 way - 150 mm dia M.S. Pipe as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 174 | Supplying, installing and commissioning Portable Fire extinguishers of Carbon-di- oxide type fire extinguisher of 4.5 kgs. Capacity, CO2 gas filled in brand new seamless cylinder with powder coated finish, made out of Manganese steel, with wheel type valve, discharge nozzle, bend & horn, wall mounting bracket etc. complete, confirming to IS: 15683 as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 175 | Supplying, installing and commissioning of water stored pressure type of 6 -9 Kgs. Capacity, with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union, high pressure CO2 gas cartridge, discharge hose, floor trolley type / wall mounting bracket etc. complete, confirming to IS:15683 as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 176 | Supplying, installing and commissioning Fire Exit Sinage board Illuminated type green colur light with battery operated hanging with chains as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 177 | Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) 450 lpm at 35 m Head a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520. b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-"F" insulation, conforming to IS-325. c)M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. d) Suitable cement concrete foundation duly plastered and with anti-vibration pads. as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 178 | Supplying and installation of 10,000 L PVC water storage tank including the connections with main line and fire pump water line as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts |
| 179 | Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalized with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter-connection, having switchgears and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for operation on 415 V, 3 phase, 50 HZ. AC supply with enclosure protection class IP 55 complete with canopy (for outdoor application) as required. A - Pump Panel i) INCOMER (a) 63 Amps. TP& N MCCB 16 KA with Thermal Magnetic O/L & S/C Protection release. (b) Voltmeter (0-500 Volts) with selector switch (c) Ammeter (0- 100 Amps.) with selector switch & CT"s etc. (d) Set of 3 Phase indicting lamp (e) Set of Al. Bar 63 Amps ii) OUTGOING (a) 63 Amps. TPN MCB with suitable appox. 8 KW (for above 450 lpm at 35 m Head Pump) fully automatic star/delta starter with over load protection, Timer, Contactor current sensing type single phase preventer complete with all accessories and internal wiring required for automatic operation, selector switch for local/remote, auto/ manual/OFF operation. The selection of all switchgear shall be as per type-2 .coordination chart.-2 Set B. SYSTEM CONTROLLER Designing, supply, installation, testing & commissioning of system controller to control operation of pumps in sequence as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
| 180 | Providing and fixing 16 mm M.S. Fan clamps of standard shape and size in existing R.C.C. slab, including cutting chase, anchoring clamp to reinforcement bar, including cleaning, refilling, making good the chase with matching concrete, plastering and painting the exposed portion of the clamps complete as per entire satisfaction and direction of Engineer-in-charge including carriage of material in all leads and lifts. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
