Tender For Miscellaneous Civil Works Including Repairing, Painting, Sanitary And Water Supply Works At Qtr No. 402 At Sanchar Minar. No Description of Item Quantity Unit Rate (Rs) Amount (Rs) 1 Supplying chemical emulsion in sealed containers including delivery as specified. a) Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 25.00 One Litre 2 Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole : a) With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. 100.00 One Metre 3 Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same. 20.00 One Metre 4 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain windowsills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing : a) 1:1½:3 (1 cement : 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). 0.50 One Cubic Metre b) 1:5:10 (1 cement : 5 coarse sand(zone-III) : 10 graded stone aggregate 40 mm nominal size). 1.00 One Cubic Metre 5 Centering and shuttering including strutting, propping etc. and removal of form for : a) Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc 5.00 One Square Metre 6 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws: a) 30 mm thick shutters. (i) With ISI marked stainless steel butt hinges of required size - Kiln seasoned and chemically treated hollock wood. (Local Hard Wood) 1.00 One Square Metre 7 Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : a) 20 mm dia (heavy type) 10 One Running Metre 8 Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : a) 100x58x1.90 mm 2.00 Each b) 75x47x1.70 mm 2 Each 9 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : a) 200x10 mm 2.00 Each b) 150x10 mm 2 Each 10 Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : a) 125 mm 2.00 Each b) 100 mm 2 Each 11 Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws etc. complete. 5 Each 12 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. 2 Each 13 Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : a) 250x16 mm 2 Each 14 Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : a) 100x10 mm 4.00 Each 15 Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. Complete a) 75 mm 8.00 Each 16 Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. a) Double strip (horizontal type) 4.00 Each 17 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. a) 1.0 mm thick. 4 One Square Metre 18 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer , but excluding the cost of other fittings, complete all as per approved design (sectional weight of only steel members shall be measured for payment). a) Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3coarse sand : 6 graded stone aggregate 20 mm nominal size). 10.00 One Kilogram 19 Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. a) In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 5 One Kilogram 20 12 mm cement plaster of mix : a) 1:6 (1 cement: 6 fine sand) 2 One SqM 21 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. 10 One Square Metre 22 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : a) Water thinnable cement primer. 20.00 One Square Metre 23 Applying priming coat : a) With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) 2 One Square Metre 24 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: a) Two or more coats on new work. 20.00 One Square Metre 25 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : a) Two or more coats on new work. 5.00 One Square Metre 26 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 10.00 One Square Metre 27 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : a) One or more coats on old work. 340 One Square Metre 28 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : a) One or more coats on old work. 170.00 One Square Metre 29 French spirit polishing : a) One or more coats on old work. 15 One Square Metre 30 Distempering with 1st quality acrylic washable distemper (ready made) having VOC content less than 50 gm per ltr. of approved manufacturer and of required shade and colour complete as per manufacturers specification. a) One or more coats on old work. 85.00 One Square Metre 31 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : a) With cement mortar 1:4 (1 cement : 4 fine sand). 10 One Square Metre 32 Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: a) Float glass panes of thickness 4 mm. 1.00 One Square Metre 33 Renewal of old putty of glass panes (length) . 20.00 One Running Metre 34 Providing & fixing White vitreous china water closet squatting pan (Indian type) along with S or P trap including dismantling of old WC seat and S or P trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. a) Orissa pattern W.C Pan of size 580x440 mm 1.00 Each 35 Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge. 1.00 Each 36 Dismantling 15 to 50 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineerin-Charge. (a) Internal Work- Exposed on wall 10.0 One Metre 37 Demolishing lime concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of Engineer in-charge 2 One Cubic Metre 38 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. a) Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 0.1 One Cubic Metre 39 Taking out doors, windows grill and clerestory window shutters (steel or wood) including stacking within 50 metres lead:and refixing the same as per direction of EIC. a) Of area 3 sq. metres and below 2.00 Each 40 Dismantling of flushing cistern of all types (C.I./PVC/Vitreous China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. 1 Each 41 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 5 One Square Metre 42 Providing and fixing Stainless Steel A Isis 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : a) Kitchen sink with drain board (i) 510x1040 mm bowl depth 178 mm. 1 Each 43 Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan. 1.00 Each 44 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. a) 10 litre capacity - White 1.00 Each 45 Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : a) White solid plastic seat with lid 1 Each 46 Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : a) Flat back wash basin of size 550x400 mm. 1.00 Each 47 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. a) Flexible pipe (i) 32 mm dia 1.00 Each 48 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 2.00 Each 49 Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. 2.00 Each 50 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. a) 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 1.00 Each 51 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall a) 15 mm nominal outer dia. Pipes. 6 One Mtr b) 20 mm nominal outer dia. Pipes. 4 One Mtr 52 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall. a) 15 mm dia. nominal bore 4 One Running Metre b) 20 mm dia. nominal bore 4.00 One Running Metre 53 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : a) 100 mm diameter 2 Each 54 Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : a) 15 mm nominal bore. 1.00 Each b) 20 mm nominal bore. 1 Each 55 Providing and fixing C.P. brass bib cock and stop cock of approved quality conforming to IS:8931: a) 15 mm nominal bore. 2.00 Each 56 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore a) 15mm nominal bore 2 Each 57 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. a) 15 mm nominal bore with 45 cm length. 3.00 Each 58 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) : a) For fixed portion (i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) 5.00 One Kilogram b) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). (i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) 2.00 One Kilogram 59 Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge. a) Bars upto 12 mm diameter 10.00 One Running Metre b) Bars above 12 mm diameter 10 One Running Metre 60 Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect. a) SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer 5.00 One Square Metre 61 Cleaning floor with Soap/ Detergent water using scrubber brush, sponge, Scotch Brite etc to remove dirt, spots, stains from floor, skirting etc. including washing floor with fresh water and drying complete as per diretion of Engineer in Charge. 120.00 sqm 62 Easing oiling and adjusting steel shutters including scraping all members and fittings so as to make the shutters easily operable. 18.00 Each pair 63 P/F C.P. brass pillar cock of approved quality and make (like Essco, Jaquier,etc.)conforming to IS standards. a) 15 mm dia nominal bore 2 Each 64 Providing and fixing Commode Jet of approved quality along with connection pipe complete as per direction of Engineer-in-charge. 1 Each 65 Providing and fixing 15 mm dia 600 mm long c.p connector pipe with coupling at both end of approved brand and manufacture like paryware etc. complete . 3 Each 66 Providing and fixing C.P. Brass Basin Mixer fro mixing hot and cold water at basin of approved brand like Essco, Ess Ess etc complete as per direction of Engineer in charge. a) 15 mm Nominal dia 1.00 Each 67 Polishing only old tiles, marbel or terrrazo work with oxalic acid powder using 33gms/sqm by mannual labour /machine where necessary 20.00 sqm 68 Providing and fixing high pressure PVC ball valve (Solvent Weld) of make Supreme or equivalent with pressure class SCH:80 of approved quality including the cost of necessary uPVC socket, pieces of pipes etc. required for the work complete as per direction of EIC a) 20 mm dia. nominal bore 2 Each 69 Rewashring of 15 mm dia stop cock /bib cock/pillar cock including gland packing if nesessary 5 Each 70 Labour for dismantling GI pipes with fittings. a) upto 25mm dia 3.00 mtr 71 Removing chokage of G.I pipe including the cleaning pipe and refixing it a) 15mm 3 Metre b) 20mm 3.00 Metre 72 Renewing hinge of Steel shutter including taking out old one by cutting and fixing new hinges by welding and mending good damages complete. 2.00 each 73 Renewing M.S Members of steel shutter by Welding including taking out old ,mending good damages complete, including taking out and refixing glass panes. 2.00 metre 74 Supplying, fitting and fixing PVC flushing cistern parts after removing the defective parts complete as per direction of the Engineer-in-Charge. (a) Polythene syphone with nut , plunger plate, plunger rod and lifting device complete. 1 Each b) Handle lever set for PVC flushing cistern. 1.00 Each 75 Labour charges for fixing of wash basin in the wall after cleaning with all necessary clamps and finishing the fitting with white cemtn etc. after completion of repairing work as per direction of Engineer-in-charge. 1.00 Each 76 Repairing cistern i/c cleaning, washing with muriatic acid and refixing the existing fittings complete. 3.00 Each 77 Removing chokage of urinal, water closet ( Indian & European type) and waste trap and clean with acid. 3.00 Each 78 Repairing of damaged door, window shutter i/c dismembering the parts & refixing the same after repairing with same/new screws all complete as per direction by the engineer-in charge (payment of new panels, styles, rails hinges shall be paid in respective item). 1.00 Each 79 Labour charges for miscellaneous works like easing of wooden doors, drawers, tower bolts, cleaning of walls to remove stickers, pencil/colour sketches,pasting of Sunmica, cleaning of shaft floor beside kitchen etc as directed by Engineer-in-charge. 2 each 80 Credit Value a) G.I. pipe: up to 20 mm dia 10.00 Metre b) M.S./ iron materials 20 Kg C) Brass/CP Bib cock,stop cock 10.00 Each
