Tender For Lab Tables

Sharing tender

Tender For Lab Tables Lab table (Length 3.9 m, width 1.5 m) 1 Length 3.9 m, width 1.5 m, with two sinks, e frame type, with electric trunking and 4 electric boards, granite worktop, bench storage cabinets with drawers, metallic frame, reagent racks, height 3 feet. Lab table (Length 3.9 m, width 0.75 m) 1 Length 3.9 m, width 0.75 m, without sinks, c frame type, with electric trunking and 6 electric boards, granite worktop, bench storage cabinets with drawers, metallic frame, and reagent racks, height 3 feet. Lab table (Length 3.9 m, width 0.9 m) 1 Length 3.9 m, width 0.9 m, without sinks, c frame type, with electric trunking and 6 electric boards, granite worktop, bench storage cabinets with drawers, metallic frame, and reagent racks, height 3 feet. Sink Unit 2 Polypropylene moulded sinks should be made up of 5 mm thick high-density and elastic polypropylene with good resistance to organic solvents. Standard bowl size (L x W x D) should be 500 x 400 x 300 mm. Faucet shall be 3-way or 1-way type faucet of approved make. Service fittings are of cast red brass alloy or bronze forgings, all fittings are of powder plated unless specified otherwise. Reagent Shelves 3 It should be complete modular design consisting of 2 storage shelves. 270mm gap to be maintained between two shelves. Reagent shelf post will have a cross section of 115mm x 30mm hollow structure of 1.2mm thick. And, metal shelves of 0.8mm thick CRCA MS with pure epoxy powder coating sheets to kept in between the frames. All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross-section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This shall provide more knee space or leg space and would facilitate uninterrupted lateral movement of the under-bench units within the bench run. The C-frame legs should be supplied with adjustable feet (tolerance from - 5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus. HORIZONTAL MEMBERS These should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two C-Frames together as shown using C-clamps/U-clamps. Together with the C-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent C-Frames. They should be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800. WELDED UNDER-BENCH STORAGE CABINETS Welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front is of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Storage Units to be of the following types: 1. Suspended Type 2. Sliding Type 3. Castor-based Mobile Type (depending upon the requirement in the schedule of quantity) Dimensions: W-300/450/600/750/900 mm, D 530mm, H 635/485 mm. Configurations: 1 Shutter/ 2 Shutters+ No Drawer/1 Drawer/2 Drawers/3 Drawers, MOC: MSCRCA: IS-513 (1994). Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip. Top cover panel should be of 0.8mm thk. Finish: Powder coating pure epoxy, thickness 40- 50 microns. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm. Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit). Hinge: Knuckle-butt type SS Hinge. Screw: SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide: 500mm Length (required only for drawer unit). Shutter should have provision of roller catch. ELECTRICAL TRUNKING Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking should be made from 1.0 mm thick CRCA MS panel. It should be available in both, single sided and double-sided configurations. It should be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope WORKTOP It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. A representation the worktop edges is shown as under ADDITIONAL TERMS & CONDITIONS: 1) The material shall be supplied from ISO 50001:2018, ISO 9001:2015, ISO 14001:2015, ISO 45001 2018 Certified Manufacturers. 2) Bidder/OEM Must submit Product Catalogue LIST OF ACCESSORIES Steel confirming to IS code Pure epoxy powder coating: 50 microns.thick or more . • Emergency devices, Water Faucets and Gas Valves, Fume Hood Utility ⚫ Fitting Watersaver, Switches and Sockets, Data and LAN points ⚫ Locks: Bras 6 leaver ⚫ Drawer slides with Telescopic Hinges Sink (PP sink) - Worktop - Jet Black Granite • Storage for Flammable items - Blower Seat, Colasit, Almonard, Premier Spot Extractors