Kerala Small Industries Development Corporation Limited has published Tender For E- Tender For The Interior Work At Kollam. Submission Date for this Tender is 19-08-2023. Interior Work Tenders in kollam Kerala. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | e-tender for interior works at Kollam For more details refer tender documents. |
| 2 | Appendix 1 : Interior and furnishing NDSR: Glass partition with powder coated aluminium Frame : Providingand fixing 8 mm toughnedglass(Saint Gobain) partition systemas per approved drawing .Glass to be fixed using 25mm x 50mm aluminium Powder Coated square tube with 6mm C channel .Use silicon sealant wherever necessary. Finish the partition as per approved design. Including cost and conveyance charges of all materials, labour charges etc., |
| 3 | Toughened Glass Door : Single door Providing and fixing doorof 10mm thickToughened glass door (Saint Gobain) with dorma(Crown)patch fittings(Floor Spring, Top patch, pivot Pin, Bottom patch, Corner lock, Handle.Including all cost and conveyance of materials, labour etc complete. |
| 4 | Modified 9.105.2 : Gypsum Board Partition with MR board : Providing and fixing partition using 12.5 mm thick tapered edge gypsum moisture resistant board up to ceiling height (upto 360cm) consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture"s specification and direction of engineer in charge all complete.75 mm overall thickness partition with 12.5 mm thick Moisture Resistant Board |
| 5 | 10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 6 | 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 7 | 13.60.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 8 | 13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer |
| 9 | NDSR: Providing & Fixing Mineral Fibre Acoustical Edge Tiles With 15mm Exposed GRID over existing Suspended Ceiling System. The tiles should have Humidity Resistance (RH) of 99%, NRC 0.5, Light Reflectance 287%, Thermal Conductivity k = 0.052 -0.057 w/m K, White and any colour, Fire Performance UK Class 0 / Class 1 (BS 476 pt 6 &7) in module size of 600x 600 x 16mm, suitable for Green Building application,with Recycled content of 30%. The Tile should carry a 10-year warranty. |
| 10 | NDSR: Fibre Cement Board Ceiling :Providing and laying 6mm Thick Fibre Cement Board in any colour On Existing Frame |
| 11 | NDSR: Design, printing and installation of graphics onwallwith Digitally reproduced art work printed on self adhesive vinyl film and installed over existing surface of partition/panelling as per details . |
| 12 | NDSR: Design, printing and installation of graphics onwallwith Digitally reproduced art work printed on self adhesive vinyl film and installed over EPE foam board of 4 mm thick of partition/panelling as per details . |
| 13 | NDSR: Applying and fixing etching stickerIncluding all materials and labour charges etc |
| 14 | NDSR:Sealing of all ventilation using frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre,including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum moisture resistant board |
| 15 | NDSR: Providing and fixing window blinds - sheer blinds |
| 16 | Supplying Puff Stool MAaterial , Size and weight Size :- 40 cm x 40 cm x 52 cm ( 16’’ x 16’’ x 21’’ )inches Weight 4 kgstool with costors for mobility. Shape :- wooden barrel round ,4 stable legs . Fabric :- premium quality cushion , smooth sitting. SEAT TYPE :- single setter 3 inches pouf fully cushion floor standing and comfortable seating.and comfortable seating maximum weight supported 150 kg |
| 17 | Providing and fixing Low height storage 1.5m x .6m x.75m shall be formed out of a combination of 16 mm and 8mmthick BWR/BWPPlywood with 1mm laminate andall exposed edges lipped with laminatededge banding. Inside portion of the storage shall be covered with0.8mm laminate.Rates include all materials and labour charges etc |
| 18 | Meeting room table: Size: 2400 L X 900 W X 750 H mm 18Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band. Under structure: Necessary wire managent so that switches to be mounted on wire traybelow table top and acccesed using soft closing access flap (atleast 2 openings ), coated leg and beams. Accessories (excluding switch and socket). Leg: Central supports with MS powder |
| 19 | Supplying High tableSize 2100 L x 1200 W X 1050 H mm, Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band. Under structure : Necessary wire managent so that switches to be mounted on wire tray below work top and acccesed using soft closing access flap, Accessories (excluding switch and socket) , Leg : MS powder coated leg and MS powder coated edge beams. |
| 20 | Supplying High stool with metal leg andtop with cousion stool height 91 cm |
| 21 | 13.45.1. Finishing walls with textured exterior pint of required shade: New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm |
| 22 | Providing and fixing in place Round Tableof size 600mm dia MS single round pillar stand withengineering wood top The rate will include all other necessary hardware,materials and labour charges etc. |
| 23 | Workstation Chairs: Mid back with armrest, multiple locking system, Seat upholstered with PU Foam & back with mesh. Gas lift for seat and height adjustment, Nylon base with castor and synchro-Tilt mechanism..(confernce room and workstations) |
| 24 | Linear Workstations : Size 1200 L x 600 W X 750 H mm, Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band. Under structure : Necessary wire managent so that switches to be mounted on wire tray below work top and acccesed using soft closing access flap, Accessories (excluding switch and socket) , Leg : MS powder coated leg and MS powder coated edge beams. Front separation above the table top, 300mm height acrylic screenpartition on table top with neccessary partition holder at the base |
| 25 | Pedestal Storage : Free Standing metal pedestal storage (646ht x 390w x 435d) Made ofsteel with multiple colour epoxy powder coated finish options which is long lasting incuding 3 draws ( 2box + 1 file) . Smooth movement of draws ensured using precision telescopic channels. 4 Numbers of Swiveling Castors are mounted below the Pedestal for easy of movement. Size : 390W x 435D x646H mm including castors for mobility |
| 26 | NDSR: Floor Carpet :Providing and laying syntheticcarpet tile Rosetta or equivalent made of 100%PP and not less than 500 gsm pile weight. The carpet shall be fire retardant and stain proof. The total thickness of carpet tiles shall not be less than 6 mm and completely waterproof resilient backing. The fixing on floor shall be done with suitable glue as per manufacturer"s specification.. |
| 27 | 13.84.1 Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.One coat |
| 28 | Electrical Item code - 1.55 -Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.GroupA |
| 29 | Group B |
| 30 | Group C |
| 31 | Item code.1.7.1 - Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2x1.5 sq.mm + 1x1.5 sq.mm earth wire |
| 32 | Item code 1.7.2-Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 33 | Item code - 1.24.1 - Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch |
| 34 | Item code - 1.24.4- Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet |
| 35 | Item code - 1.24.3-Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amps switch |
| 36 | 1.24.5Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet |
| 37 | 2.10.1Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole |
| 38 | 2.17Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32amps 415 volts "C" curve TP MCB complete with connections, testing and commissioning etc. as required. |
| 39 | 90.11.1.12Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required 8 way (8+24) - three phase double cover (IP 42/43) |
| 40 | 7.7.1Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 41 | MR80710 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE |
| 42 | MR80816 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE |
| 43 | 1.28.4 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 6 Module |
| 44 | Item code 5.2-Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required |
| 45 | 90.16.1.3 -Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required 3.15 mm copper conductor ( 10 SWG) |
| 46 | 5.4-Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 47 | Supplying and fixing following rating, double pole, (single phase and neutral), 415 V, Residual Current Circuit Breaker with Overcurrent protection (RCBO), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 Arating, 4 pole RCBO, 30mA/100mA |
| 48 | Supplying and fixing following rating, double pole, (single phase and neutral), 415 V, Residual Current Circuit Breaker with Overcurrent protection (RCBO), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40Arating, 4 pole RCBO, 30mA/100mA |
| 49 | Item code: 1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required Item code: 1.21.1 20mm |
| 50 | Item code: 1.21.2 25mm |
| 51 | 90.10.1.3 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )3 module moulded plastic box on surface |
| 52 | 1.28.2. Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 3 Module |
| 53 | Supply LED Recessed Full Glow (2X2)Luminaire with a nominal system lumen output of 3600 Lumens (130Lm/W) and a Luminaire Wattage should not exceed 36W with Electronic driver. Also Operating voltage of 140-270V with cut off and auto restart feature @325V. Power factor should be >0.95 & THD should be <10% & CRI>80. Color temperature – 5700K. LED Life should be 50,000Hrs. The luminaire housing should be made of powder coated metallic CRCA with high efficiency PS diffuser. "Dimension :Length = 595 mm , Width = 595mm, Height= 45mm .The supply of accessories like clamps, supporting brackets and hardwares as required and interconnecting with 3 core 1.5 sqmm PVC insulated FRLS copper wire with all accessories required as per site conditions similier to Philips Model No : RC380B LED36S -5700 G5 L60 W60 PSU OD |
| 54 | 1.41. Installation, testing and commissioning of pre - wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 55 | Appendix 3 : IT & Network Firewall 1) FIREWALL - 10,500 Mbps 2) TLS INSPECTION - 800 Mbps 3) FIREWALL IMIX - 5,250 Mbps 4) IPS - 3,250 Mbps 5) IPSEC VPN - 5,500 Mbps 6) NGFW - 2,500 Mbps 7) THREAT PROTECTION - 900 Mbps 8) LATENCY (64 BYTE UDP) - 8 µs 9) ETHERNET INTERFACES (FIXED) - 10 x GE copper 10)POWER-OVER-ETHERNET (FIXED) - 2 x GE 802.3at (30W max. per port) 11) MANAGEMENT INTERFACES - 1 x COM RJ45, 1 x COM Micro-USB 12) OTHER I/O INTERFACES - 1 x USB 2.0 (front), 1 x USB 3.0 (rear) |
| 56 | Supply, Installation, Testing and Commissioning of 10/100/1000 Mbps 24 Port Manageable Switch 10/100/1000 Base-T RJ45 ports: 24 1000BASE-X Fiber SFP Ports: 2 Management: Web Browser-based GUI (HTTP/HTTPS), PC-Based Smart Control Center Utility (SCC) RMON, SNMP IPv4 ACL and QoS: L2, L3, L4, ingress Pv4 Multicast Filtering: IGMP Snooping, Querier, Fast Leave, L2 Multicast Router Auto-VOIP/Auto Video: Yes IEEE (802.3az) Energy Efficient Ethernet: Yes MAC VLANs: 8K or 16K Max MAC 64 VLANs Static, Dynamic, Voice Convergence Advanced Features: LLDP-MED RADIUS 802.1X LACP, STP, SNMP Packet buffer: 512 KB CPU: 800MHz single core, 512MB DDR RAM, 2MB SPI NOR, 128MB FLASH ACLs: 100 shared Fabric: 52Gbps line-rate Latency (64-byte packets): 1G Copper: <3.86 µs Multicast IGMP Groups: 512 Number of DHCP snooping bindings: 8K Packet forwarding rate (64 byte packet size) (Mpps): 38.6 Jumbo frame support (bytes): 9216 IEEE 802.1Q VLAN tagging: Yes IP-based VLANs: Yes MAC-based VLANs: Yes Auto-Voice VLAN: Yes, based on OUI bytes (default database and user-based OUIs) in the phone source MAC address Auto-VoIP: Yes, based on protocols (SIP). Prioritzes traffic to a higher queue IEEE 802.3ad - LAGs (LACP): Yes IGMP snooping (v1, v2, and v3): Yes IGMP snooping querier: Yes DHCP client: Yes DHCP snooping: Yes IEEE 802.3ad - LAGs (LACP): Yes Manual Static LAG: Yes 802.1ab LLDP: Yes SNMP: v1, v2c, v3 RMON group 1,2,3,9: Yes IEEE 802.1x: Yes IP-based ACLs (IPv4 and IPv6): IPv4 Control MAC # Dynamic learned entries: 4096 Control MAC # Static entries: 48 Broadcast, multicast, unknown unicast storm control: Yes DoS attacks prevention: Yes Port-based rate limiting: Egress Auto-VoIP: Yes, based on protocols SIP, H323 and SCCP. Prioritzes traffic to a higher queue Voice VLAN: Yes, based on either VLAN ID or 802.1p priority, packets are passed onto the connecting VoIP phone using LLDP-MED Admin access control via RADIUS and TACACS+ : Yes Port mirroring: Yes ingress and egress Many-to-one port mirroring: 26 Smart Control Center (SCC) for multi-switch management: Yes Dual software (firmware) image: Yes TLS/HTTPS Web-based access (version): Yes (v1.2) File transfers (uploads, downloads): TFTP / HTTP HTTP upload/download (firmware) : Yes Syslog (RFC 3164): Yes Warranty and Support : Life-Time hardware replacement warranty |
| 57 | Supply, Installation, Testing and Commissioning of 10/100/1000 Mbps 24 Port PoE Manageable Switch Performance Specification Bandwidth: 52 Gbps non-blocking Mean Time Between Failures (MTBF): 1,051,375 hours Heat Dissipation (at full PoE load): 780.20 Btu/H Forwarding modes: Store-and-forward 8 Priority queues Priority queuing: Weighted Round Robin (WRR) MAC Address database size: 8,000 media access control (MAC) addresses VLAN: 64 128 Multicast groups 256 DHCP snooping bindings Packet buffer: 0.5 MB Jumbo frame: 9K Power Consumption: 228.53W Max PoE budget: 190W IEEE Network Protocols IEEE 802.3 Ethernet IEEE 802.3u 100BASE-T IEEE 802.3ab 1000BASE-T IEEE 802.1Q VLAN Tagging IEEE 802.3x full-duplex flow control IEEE 802.3z Gigabit Ethernet 1000BASE-SX/LX IEEE 802.3ad Trunking (LACP) IEEE 802.1ab LLDP with ANSI/TIA-1057 (LLDP-MED) IEEE 802.1p Class of Service IEEE 802.3 af (PoE) IEEE 802.3 at (PoE+) IEEE 802.1D Spanning Tree (STP) IEEE 802.1s Multiple Spanning Tree (MSTP) IEEE 802.1w Rapid Spanning Tree (RSTP) IEEE 802.1X Radius network access control Network Security and Traffic IEEE 802.1x Guest VLAN RADIUS based VLAN assignment via .1x MAC-based .1x Network Storm Protection Broadcast, Unicast, Multicast Protection Access Control Lists (ACLs) L2 / L3 / L4 IP-based ACLs (IPv4) MAC-based ACL TCP/UDP-based ACL MAC lockdown MAC lockdown by the number of MACs IEEE 802.1x Radius Port Access Authentication L2 Services IEEE 802.1Q VLAN Tagging Voice VLAN IEEE 802.3ad - LAGs - LACP (8 LAGS with max. of 8 members in each LAG) Broadcast Storm Control IGMP Snooping (v1, v2 and v3) MLD Snooping Support (v1 and v2) IGMP Snooping queriers DHCP Client DHCP Snooping Network Monitoring and Discovery Services 802.1ab LLDP SNMP V1, V2, V3 RMON 1,2,3,9 Quality of Service(QoS) Access Lists Egress rate limiting Diff ServQoS IEEE 802.1p COS Destination MAC and IP IPv4 DSCP IPv4 TOS WRR (Weighted Round Robin) Strict Priority queue technology Auto-VoIP Vlan Auto Voice Vlan Port Mirroring Management Password management Configurable Management VLAN Admin access control via Radius and TACACS+ Web-based graphical user interface (GUI) Dual Software (firmware) image Dual Configuration file SNTP client over UDP port 123 SNMP v1/v2 SNMP v3 with multiple IP addresses RMON 1,2,3,9 Port Mirroring Many to One Port Mirroring Cable Test utility SSL/HTTPS and TLS v1.0 for web-based access TFTP/HTTP File transfers (uploads,downloads) HTTP Download (firmware) Syslog (RFC 3164) LEDs Per port: Speed, Link, Activity Per device: Power, Fan and PoE Power Status Certifications CE mark, commercial FCC Part 15 Class A RCM: AS/NZS CISPR 32:2013 Class A ISED: ICES-003:2016 Issue 6 , Class A, ANSI C63.4:2014 EN 55024 CCC UL listed (UL 1950)/cUL IEC 950/EN 60950 Warranty and Support Life-Time hardware replacement warranty |
| 58 | Cat-6 UTP Cable Blue Color - with casing and capping and crimping with labour charge : Used for Data a) The 4 pair Unshielded Twisted Pair cable shall be FR-PVC b) This cable well exceeds the requirements of TIA/EIA-568-C.2 and ISO/IEC 11801 c) Nominal Outer Diameter of Cable should be 5.7+/-0.01mm min and Conductor Diameter 24 AWG d) Construction: 4 twisted pairs separated by internal PE Cross Separator. Full separator. Half shall not be accepted. Rip Cord is must. e) Conductor Solid bare Copper and Outer jacket sheath FRPVC and CM rated cable. Jacket color: Grey f) Insulation :High Density Polyethylene Solid g) Dielectric Strength of cable should be 1000 V RMS h) Bending Radius : < 4X Cable Diameter at -20°C +/- 1°C, Pulling Force: 25.35 LBS i) Electrical Parameters Pair – to – pair and PS NEXT, ELFEXT and PSELFEXT, Return Loss, ACR and PS ACR. j) Insertion Loss of 32.8 db/100m at 250 MHz k) Cable should support operating Temperature from -20° to +70°C l) Cable support Conductor Resistance < 9.38 O /100m m) Mutual Capacitance of cable should be < 5.6nF/100m n) Max Resistance Unbalance of cable should be 5% Max o) Capacitance Unbalance of cable should max 330pF/100m p) Cable support Delay Skew: < 45nS, Operating Voltage: 72V NVP: 69% and Current Rating : MAX 1.5A q) Printed sequential Length Counter of each meter on Outer Jacket r) Category 6 UTP cables shall Supports Gigabit Ethernet (1000 base-T) standard and Operates at bandwidth of 600MHz s) Category 6 UTP cables FR-PVC/LSZH should be 250 MHz |
| 59 | Cat-6 UTP Cable Yellow Color - with casing and capping and crimping with labour charge : Used for CCTV a) The 4 pair Unshielded Twisted Pair cable shall be FR-PVC b) This cable well exceeds the requirements of TIA/EIA-568-C.2 and ISO/IEC 11801 c) Nominal Outer Diameter of Cable should be 5.7+/-0.01mm min and Conductor Diameter 24 AWG d) Construction: 4 twisted pairs separated by internal PE Cross Separator. Full separator. Half shall not be accepted. Rip Cord is must. e) Conductor Solid bare Copper and Outer jacket sheath FRPVC and CM rated cable. Jacket color: Yellow f) Insulation :High Density Polyethylene Solid g) Dielectric Strength of cable should be 1000 V RMS h) Bending Radius : < 4X Cable Diameter at -20°C +/- 1°C, Pulling Force: 25.35 LBS i) Electrical Parameters Pair – to – pair and PS NEXT, ELFEXT and PSELFEXT, Return Loss, ACR and PS ACR. j) Insertion Loss of 32.8 db/100m at 250 MHz k) Cable should support operating Temperature from -20° to +70°C l) Cable support Conductor Resistance < 9.38 O /100m m) Mutual Capacitance of cable should be < 5.6nF/100m n) Max Resistance Unbalance of cable should be 5% Max o) Capacitance Unbalance of cable should max 330pF/100m p) Cable support Delay Skew: < 45nS, Operating Voltage: 72V NVP: 69% and Current Rating : MAX 1.5A q) Printed sequential Length Counter of each meter on Outer Jacket r) Category 6 UTP cables shall Supports Gigabit Ethernet (1000 base-T) standard and Operates at bandwidth of 600MHz s) Category 6 UTP cables FR-PVC/LSZH should be 250 MHz |
| 60 | Cat-6 UTP Cable Orange Color- with casing and capping and crimping with labour charge : Used for Access control system a) The 4 pair Unshielded Twisted Pair cable shall be FR-PVC b) This cable well exceeds the requirements of TIA/EIA-568-C.2 and ISO/IEC 11801 c) Nominal Outer Diameter of Cable should be 5.7+/-0.01mm min and Conductor Diameter 24 AWG d) Construction: 4 twisted pairs separated by internal PE Cross Separator. Full separator. Half shall not be accepted. Rip Cord is must. e) Conductor Solid bare Copper and Outer jacket sheath FRPVC and CM rated cable. Jacket color: Grey f) Insulation :High Density Polyethylene Solid g) Dielectric Strength of cable should be 1000 V RMS h) Bending Radius : < 4X Cable Diameter at -20°C +/- 1°C, Pulling Force: 25.35 LBS i) Electrical Parameters Pair – to – pair and PS NEXT, ELFEXT and PSELFEXT, Return Loss, ACR and PS ACR. j) Insertion Loss of 32.8 db/100m at 250 MHz k) Cable should support operating Temperature from -20° to +70°C l) Cable support Conductor Resistance < 9.38 O /100m m) Mutual Capacitance of cable should be < 5.6nF/100m n) Max Resistance Unbalance of cable should be 5% Max o) Capacitance Unbalance of cable should max 330pF/100m p) Cable support Delay Skew: < 45nS, Operating Voltage: 72V NVP: 69% and Current Rating : MAX 1.5A q) Printed sequential Length Counter of each meter on Outer Jacket r) Category 6 UTP cables shall Supports Gigabit Ethernet (1000 base-T) standard and Operates at bandwidth of 600MHz s) Category 6 UTP cables FR-PVC/LSZH should be 250 MHz |
| 61 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required - 25 mm |
| 62 | Cat-6 Keystone Jack a) Category 6 Keystone jack should be suitable For 23~24 AWG Stranded and Solid Wire, Easy For Termination and Compliant to T568A and T568B Wiring Schemes b) Compatible with Both 110 & Krone Punch Down Tool. c) RJ45 8P 8C 50u Jacks d) Fast, Easy, Reliable Termination e) Should Fit in High Density Keystone Patch Panel And on Face Plates f) Keystone Jack Can Be Easily Terminated by punch down tool g) Backward compatible with both RJ11/RJ12 Plug h) Physical: >Housing : High impact flame retardant plastic, UL 94V-0 rated >PCB : FR-4 T=1.6mmThickness >Contact Material : Phosphor Bronze Stamp Pin T=0.35mm >IDC Contact Material : Phosphor Bronze T=0.50mm With Tin Plating >Gold Plating : 50 microns >Connector : Insulation displacement connector >IDC to support Wire : AWG 22~24 i) Electrical: >Current Rating : 1.5amps >Insulation Resistance : 500 MO minimum >Contact Resistance : 10 mO maximum >DC Resistance : 0.1 O maximum j) Mechanical: >Plug Insertion Life : 750 Cycles minimum >Plug & Jack Contact Force :100 Grams minimum using FCC-approved plug >Plug Retention Force : 30 lbs minimum >Temperature : -40° to 150°F (-40° to 68°C) k) Standard Verification: >Qualified unscreened Class E/Cat.6 >Permanent Link & Channel ANSI/TIA-568-C.2 >IEC 60603-7-4 2nd Edition >ISO/IEC 11801 2.2 Edition >CENELEC EN 50173-1:2011 |
| 63 | RJ11 Keystone |
| 64 | Face Plate Single a) British style Square Face Plate (86 x 86mm) b) Shutter on Face Plate c) Elegant : hidden-screw design d) Glossy Finish : Suite for all decor e) MATERIAL: ABS 765 UL94V-0 f) Plug Retention Force : 14Kgf (140N) g) Plug Reliability : 750 Cycles minimum h) Should support UTP and STP Jacks Cat5e, Cat6 and Cat6A i) Standard Verification: >ANSI/TIA-568-C.2 >ISO/IEC 11801:2002 AMMD.2:2010 >YD/T 926.3-2009 >ISO/IEC 60603-7 Compliant >RoHS Directive 2002/95/EC/Compliant |
| 65 | Face Plate Dual a) British style Square Face Plate (86 x 86mm) b) Shutter on Face Plate c) Elegant : hidden-screw design d) Glossy Finish : Suite for all decor e) MATERIAL: ABS 765 UL94V-0 f) Plug Retention Force : 14Kgf (140N) g) Plug Reliability : 750 Cycles minimum h) Should support UTP and STP Jacks Cat5e, Cat6 and Cat6A i) Standard Verification: >ANSI/TIA-568-C.2 >ISO/IEC 11801:2002 AMMD.2:2010 >YD/T 926.3-2009 >ISO/IEC 60603-7 Compliant >RoHS Directive 2002/95/EC/Compliant |
| 66 | Back Box (Network) a) Should have Robust and installer friendly design Surface MountBoxes for Face Plates for a variety of media including voice and data, Audio, video and CATV distribution to the work area. b) Should secure and protect wire with durable wall box c) Material : ABS d) Shape : SquareSize : 86 x 86 e) Color : White |
| 67 | Back Box (Camera) a) Should have Robust and installer friendly design Surface MountBoxes for Face Plates for a variety of media including voice and data, Audio, video and CATV distribution to the work area. b) Should secure and protect wire with durable wall box c) Material : ABS d) Shape : SquareSize : 86 x 86 e) Color : White |
| 68 | Cat-6 24 Port Patch Panel Loaded-Installation only a) The Cat-6 transmission performance is in compliance and Exceeds ANSI/TIA/EIA-568-C.2 Standard. Supports 1000-Base-T. b) Modular Design in loaded or individual port design in UnLoaded for Convenient NetworkTerminations c) Built in Rear Cable Management for Ease of Installation. d) Removable Module Design for repair or maintenance. e) 6x4 Module Specially Designed Jack Configuration f) PCB: FR4, 1.6mm Thickness. g) IDC Conductor : 0.5 mm Phosphor Bronze, Tin Plating h) Contact Compatibility : 22~26 AWG Stranded and Solid Wires i) 1U Patch Panel to Mount In any Standard Rack. Panel Frame: SPCC Powder coated black. j) Housing : High Impact Flame Retardant Plastic, UL 94V-0 Rated k) Easy Port Labeling Identification Provision l) Electrical Characteristics: >Current Rating : 1.5amps >Insulation Resistance : >= 500mO >Contact Resistance : <=10mO >DC Resistance : <=0.1O >DC/AC Volt Endurance : DC 1000V/AC 750V 1 Min m) Mechanical Characteristics: >Plug Insertion Life : >= 750 Cycles with FCC Compliant RJ-45 Plug >Plug & Jack Contact : >= 100 Grams with FCC Compliant RJ-45 Plug Force >Plug Retention Force : >= 11 LBF >Durability : 200 Termination Cycles >Operating Temperature : -10 Degree ~ 60 Degree >Operating Humidity : 10% ~ 90% RH >Storage Temperature : -40 Degree ~ 68 Degree n)Standard Verification: >ANSI/TIA-568-C.2 >ISO/IEC 11801:2002/AMMD.2:2010 >YD/T 926.3-2009 >ISO/IEC 60603-7 Compliant >RoHS Directive 2002/95/EC/Compliant >UL Listed |
| 69 | Cat 6 1 MtrPatch Cord Blue a) Category 6 UTP Patch Cords should be Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. b) Complies with the ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T c) Should be FR-PVC/ LSZH Jacket for Reduced Toxic Gasses Emitted During Combustion d) RJ45, 8P8C, 2 FORK 50µ’’ Gold Plated Contacts e) Patch cords should be 100% Factory Tested f) Transparent Boot Cable Assemblies g) Should be Available in Different Colors on request h) Technical Specifications : >Conductor Material : Stranded Copper >Conductor Diameter : (24 AWG) >Insulation Thickness : Min at any point: 0.18mm MAX AVG:0.20mm >Min at any point: 0.17mm MAX AVG:0.19mm >Insulation Diameter : 0.94±0.01mm/0.92±0.01mm >Cross Filler : Transparent 4.2×0.35 >Jacket Type:FR-PVC/LSZH (Low Smoke Zero Halogen) >Jacket Thickness : Min at any point: 0.51mm MAX AVG: 0.55mm >Jacket Width : Min at any point: 5.2mm MAX AVG:5.8mm >Plug : 50µ’’ Gold Plated Contact >Boot : Transparent >Standard : ANSI EIA/TIA 568-C.2 |
| 70 | Cat 6 1 MtrPatch Cord Yellow a) Category 6 UTP Patch Cords should be Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. b) Complies with the ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T c) Should be FR-PVC/ LSZH Jacket for Reduced Toxic Gasses Emitted During Combustion d) RJ45, 8P8C, 2 FORK 50µ’’ Gold Plated Contacts e) Patch cords should be 100% Factory Tested f) Transparent Boot Cable Assemblies g) Should be Available in Different Colors on request h) Technical Specifications : >Conductor Material : Stranded Copper >Conductor Diameter : (24 AWG) >Insulation Thickness : Min at any point: 0.18mm MAX AVG:0.20mm >Min at any point: 0.17mm MAX AVG:0.19mm >Insulation Diameter : 0.94±0.01mm/0.92±0.01mm >Cross Filler : Transparent 4.2×0.35 >Jacket Type:FR-PVC/LSZH (Low Smoke Zero Halogen) >Jacket Thickness : Min at any point: 0.51mm MAX AVG: 0.55mm >Jacket Width : Min at any point: 5.2mm MAX AVG:5.8mm >Plug : 50µ’’ Gold Plated Contact >Boot : Transparent >Standard : ANSI EIA/TIA 568-C.2 |
| 71 | Cat 6 1 MtrPatch Cord Orange a) Category 6 UTP Patch Cords should be Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. b) Complies with the ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T c) Should be FR-PVC/ LSZH Jacket for Reduced Toxic Gasses Emitted During Combustion d) RJ45, 8P8C, 2 FORK 50µ’’ Gold Plated Contacts e) Patch cords should be 100% Factory Tested f) Transparent Boot Cable Assemblies g) Should be Available in Different Colors on request h) Technical Specifications : >Conductor Material : Stranded Copper >Conductor Diameter : (24 AWG) >Insulation Thickness : Min at any point: 0.18mm MAX AVG:0.20mm >Min at any point: 0.17mm MAX AVG:0.19mm >Insulation Diameter : 0.94±0.01mm/0.92±0.01mm >Cross Filler : Transparent 4.2×0.35 >Jacket Type:FR-PVC/LSZH (Low Smoke Zero Halogen) >Jacket Thickness : Min at any point: 0.51mm MAX AVG: 0.55mm >Jacket Width : Min at any point: 5.2mm MAX AVG:5.8mm >Plug : 50µ’’ Gold Plated Contact >Boot : Transparent >Standard : ANSI EIA/TIA 568-C.2 |
| 72 | Cat 6 2 MtrPatch Cord Blue a) Category 6 UTP Patch Cords should be Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. b) Complies with the ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T c) Should be FR-PVC/ LSZH Jacket for Reduced Toxic Gasses Emitted During Combustion d) RJ45, 8P8C, 2 FORK 50µ’’ Gold Plated Contacts e) Patch cords should be 100% Factory Tested f) Transparent Boot Cable Assemblies g) Should be Available in Different Colors on request h) Technical Specifications : >Conductor Material : Stranded Copper >Conductor Diameter : (24 AWG) >Insulation Thickness : Min at any point: 0.18mm MAX AVG:0.20mm >Min at any point: 0.17mm MAX AVG:0.19mm >Insulation Diameter : 0.94±0.01mm/0.92±0.01mm >Cross Filler : Transparent 4.2×0.35 >Jacket Type:FR-PVC/LSZH (Low Smoke Zero Halogen) >Jacket Thickness : Min at any point: 0.51mm MAX AVG: 0.55mm >Jacket Width : Min at any point: 5.2mm MAX AVG:5.8mm >Plug : 50µ’’ Gold Plated Contact >Boot : Transparent >Standard : ANSI EIA/TIA 568-C.2 |
| 73 | 2 MP IP Survillence Camera - Bullet ? 2MP, HDCVI IR Bullet camera ? 30 fps@1080P 3.6mm fixed lens Max IR length 20 m ? Smart IR IP67 ? DC 12V ? Night vision |
| 74 | 8 Channel NVR with 4 TB Survillence HDD Support 8 channel IP camera input Smart H.265+/H.265/Smart H.264+/H.264 codec decoding Up to 8MP resolution preview and playback VGA/HDMI simultaneous video output, maximum resolution of HDMI is 1080P Motion detection: yes User Interface Web/operating in local GUI |
| 75 | Biometric Access Control device with perpectual license software (license software shall be used to manage the exit and entry devices for all doors) for attendence tracking (Exit + Entry) - Cloud Control software for managing the cards remotely. 1) Fingerprint Capacity : 10000 2) Card Capacity : 10000 3) Transaction Capacity : 100000 4) Card Reader : Inbuilt proximity card reader (Optional Mifare, HID prox) 5) CPU : 32bit microprocessor 6) SDRAM : 128 MB Nand Flash 7) Flash : 256 MB Nand Flash 9) Kernel : 2.6 10) Fingerprint sensor : 500 DPI Optical sensor 11) FAR : <=0.0001% 12) FRR : <=1% 13) Identification speed : <0.5 sec 14) desktop & web 15) SDK for desktop applications 16) Web based Device Management application using Push data. Helps developers & integrators 17) Supports 3rd Party Payroll/HRMS/ERP and Other applications |
| 76 | EM Lock - Double Leaf lock 1) MOV provides spike and surge protection 2) Magnetic bond sensor monitor output 3) Door position status sensor output 4) Bi-color LED indicates lock/unlock status 5) Anodized aluminum housing 6) Anti-Residual magnetism designed 7) Complete mounting hardware included. 8) Voltage Tolerance: 115% 9) Current Draw:400mA 12\I DC (at temperature 20°c ) 10) Magnetic bond sensor monitor output (SPOT rated 1A 12V DC), remotely monitors the door lock or unlock status. (N.C. Output--Door opened; N.O. Output-Door closed) 11) Operating Temperature: -10-55°C 12) Humidity:0-95% non-condensing 13) Lock"s surface Temperature (when the power is on): S current temperature +20°C 14) Holding Force: 280KG (600pounds) 15) Dimensions : Lock Size:(L) 250, (W) 48, (0) 26 mm 16) Mounting Plate Size : (L) 250, (W) 25, (0) 6 mm 17) Armature plate Size : (L) 180, (W) 38, (D) 11 mm 19) Special Finishes for magnet and armature plate: Zinc |
| 77 | EM Lock - Single Leaf lock 1) 600LBS EM lock, 5 wires 2) Fail safe : Lock when energy on 3) Holding force : 280Kg(600lbs) 4) Weight:2 Kg 5) Working current / voltage: DC12V/450mA / DC24V/230mA 6) Signal output : NO/NC/COM |
| 78 | Projector with Instalock projector screen and ceiling mount kit-Installation only 3,600 Lumens 3LCD technology for equal white & colour light output XGA resolution and 4:3 performance Long lamp life up to 12,000 hours in ECO mode Easy setup and positioning flexibility HDMI connectivity Projection Technology: RGB liquid crystal shutter projection system (3LCD) Interface: USB 2.0 Type B, RS-232C, Wired Network, Wireless LAN a/n (5GHz) (optional), VGA in (2x), VGA out, HDMI in, Composite in, Stereo mini jack audio out, Stereo mini jack audio in (2x), Cinch audio in, USB 2.0 Type A Aspect Ratio:: 4:3 Native Resolution: XGA, 1024 x 768 Fan Noise (Normal / Eco): 37dB / 28dB Colour Light Output: 3,600 Lumen*1- 2,400 Lumen (economy) White Light Output: 3,600 Lumen |
| 79 | Chrome Cast |
| 80 | PC - needed for installing Access control software, survillence software and network management software 1) 15 inch> Monitor 2) Keyboard 3) Mouse 4) CPU - i3 latest generation 8 GB ram 256 GB M.2 Mvme ssd Windows 11 Pro Latest MS Office perpectual License |
| 81 | Rack - 24 U with atleast 10 point PDU |
| 82 | Cable Manager - 24 Port |
| 83 | 50-inch UHD display Support min Resolution of 3840x2160(16:9) shall support the Pixel Pitch(mm) 0.372 x 0.372and Contrast Ratio of 4000:1 (* IPS - 1200:1) shall support the gaze of non-Glare ,Color Gamut 92% (DCI-P3, CIE 1976) |
| 84 | Wi-Fi Access Point a) WiFi Standards: 5.0GHz: 802.11a/n/ac/ax, 2.4GHz: 802.11b/g/n/ax b) Wireless Mode (Transmit x Receive): 2x2 in 5.0GHz, 2x2 in 2.4GHz c) OFDM/OFDMA: OFDM and OFDMA d) BSS Coloring: Yes e) Multi-User MIMO: Bidir and MU-MIMO f) Target Wake Time : Yes h) Maximum Theoretical Throughput: AX1800 1.8Gbps i) Maximum Theoretical Throughput per Band: 5.0GHz: 1200Mbps, 2.4GHz: 600Mbps j) Antenna Gain: Internal 3.8/4.5dBi (2.4GHz/5GHz) k) Limited Life time warranty l) Power over Ethernet (PoE): 802.3at/af m) Secure Socket Layer (SSL): Yes n) Repeater: Yes o) Bridge Point-to-point/Multi-point: Yes p) Simultaneous Bridge and Wireless Client Association: Yes q) WiFi Protected Access (WPA/WPA2/WPA3), 802.11i : Yes r) MAC address filtering with access control: Yes s) 802.1x RADIUS support with EAP TLS, TTLS, PEAP: Yes t) VLAN Support: Yes u) Guest Network/Captive Portal: Yes v) Bandwidth management: Yes w) Link Layer Discovery Protocol: Yes x) IEEE 802.11ax WiFi 6 standard: Yes y) WMM Wireless Multimedia Prioritization:Yes z) WDS Wireless Distribution System: Yes a1) Interface: One 100/1000/2.5GBASE-T Gigabit Ethernet (RJ-45) ports with Auto Uplink™ (Auto MDI-X) supporting IEEE 802.3af or 802.3at Power over Ethernet (PoE) a2) WiFi Protected Access® (WPA, WPA2, WPA3): Yes a3) WPA2 Enterprise: Yes a4) Wireless access control to identify authorized wireless network devices: Yes a5) Limited life time warranty as per tender document |
| 85 | Appendix 4 :HVAC WorkSupplying and fixing 1.5 TR 3 StarSplit AC (indoor unit and iutdoor unit) with cordless remoteFull Copper Model including allinstallation charges etc(Director)with suitable voltage stabiliser |
| 86 | Supply and fixing outdoor standincluding all materials and labour charges etc |
| 87 | Supply and installation of Copper Refrigerant piping with nitrile rubber insulation of required sizes clamping on walls, refrigerant gas charging of required size . Complete. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
