Tender For Supply Of Construction /Hardware Material I.E., Ac Sheet, Cement, Wire Mess, Ms Pipe Hooks & Washer, Binding Wire, Nails, Bituminous Washer Pkt, Waterproof Cement And Welded Mesh Etc. Asbestos sheet (2.25- meter x 1.05 m) Thickness nominal 6mm, Over all Width 1.05 m, Laid width 1.01 m, efficiency 91% (Allowing for side and end laps with 2.25 m sheet,, Weight of 100 sq m as laid 1.40 M Tonnes, Standard Length - 2.25 m colour available - Natural Gray Cement (Ultratech) Ordinary Portland Cement (OPC), cement, Per Bag, Fine ness 0.08mm sieve max, initial setting time min 45 minute and maximum setting time max 10 hours. Galvanized Welded Wire Mesh (6.10 m x 1.06m) Type of selvage - Galvanized weldedwire mesh(Square Type), Mesh size in mm - 1.63 mm, Nominal diameter of Mess wire in mm -1.63 mm, Length of the Fabric in Meter 6.10 m,Width of the Fabric in Meter- 1.06 m Diameter of the line Wire (mm) -1.63 mm, Number of Line wire in width (44 Lines to 63 Lines), Minimum weight per square meter of Galvanized Iron Wire - 1.5KG to 2.5 KG, The diameter of the wire mesh as perstandard wire mesh (SWG) Galvanized Chain Linked Wire Mesh 1.22 m) (10.97 m x Galvanized Chain liked Wire mesh, Mesh size in mm 2.64mm, Nominal diameter of Mesh wire in mm 2.64mm, Length of fabric 10.97 m, Width of the fabric in meter 1.22 m, Diameter of the line wire in mm-2.64 mm, Number of line wire- (13-20)nos minimum weight per square meter of galvanized iron wire -2.2 kg to 2.5 kg, Diameter of wire mesh in (standard wire mesh - SWG Jhook and Washer, Screw Colour- silver, Finish Type- GI, Item shape J, Material type - Wire wound, Measurement system Inch, Pitch 18 teeth per pitch, Size- 6inch standard, Thread length 40 mm, Thread type- UNC,Diameter - 6mm- 10mm, thickness-1.6 mm- 2.5mm Binding Wire As per Indian standard code1S2502:1963. The binding wire should be 16 to 18 gauges in size, It shall be free from rust, oll, paint, grease, loose mill scale or any type. Nails Material Iron, Size- 2-to-3- inch, Flat head, Diamond Point, round smooth shank. Bituminous washer packet Each material containing Circular in shape. Free from any damage. The material should be in round or circular shape and packed in a closed packet. Length of each pipe Mild steel Pipes (MS) (41.9 42.5) mm OD and 2.6 2.9mm 2.00 to 2.54. kg/meter thickness, Weight should be 13ft. Thickness of the pipe should be ranges between 2-2.9 mm. Weight of the item should be varied from 2 to 2.54 kg/meter length. The ends are cleanly finished by nominal deburring process. A long hollow, open- ended object of circular cross section. Water Proofing Cement Paint The material shall be free from odour of putrefaction shall be free from lumps, skins and the conditions of the material shall be such that settling, if any may be easily incorporated on stirring. When suitably thinned with water, the material shall mix readily with minimum amount of foaming to a smooth and homogeneous state After the application by brush the resulting film shall not show pigment flocculation, coarseness or other undesirable characteristics. To check the consistency, if a metal rod or palette knife insert into the original container the material shall not cake hard inside the container and shall be in such a condition that stirring easily produces a smooth uniform paint suitable for application.
