|
| 1 | Overhauling Charges of the following Pump including Dismentaling, Machining , Oiling , Greasing , Assembling & Installation at Site includingloading and unloading,to and fro transportation ofpump from NSG Campus Manesar to the workshop. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 2 | UP80/38 |
| 3 | UP125/30 |
| 4 | SP-3L |
| 5 | Replacement of the following spare parts of the existing KBL Pump UP80/38 or UP125/30 \"Kirloskar\" make drive by electric motor 25HP capacitywith a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. |
| 6 | Pump Shaft(CS) |
| 7 | Shaft Sleeve |
| 8 | Wear Ring |
| 9 | Gland Plate (CI) |
| 10 | Ball Bearing Set |
| 11 | Set of O-ring |
| 12 | Set of Gasket |
| 13 | Set of Fastners |
| 14 | Cooling Pipe |
| 15 | Bearing Housing (DE Side) |
| 16 | Replacement of the following spare parts electric Induction motor 25HP capacitywith a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. |
| 17 | Bearing -Set |
| 18 | Terminal Plate |
| 19 | Fan Cover |
| 20 | Fan |
| 21 | Terminal Box |
| 22 | Coupling |
| 23 | Rewinding ofelectrical motors including all necessary material and of the same characteristics as original with required size of super enameled copper wire and F class insulation material including dismantling, removing of burnt wires, cleaning of slots, varnishing, assembling, greasing, testing etc. complete as required including credit for old scrap material which will be retained by the contractor etc., complete as required. |
| 24 | Providing and fixing C.I. sluice valves (with cap) complete with bolts,nuts, rubber insertions etc. (the tail pieces if required will be paidseparately) : |
| 25 | 150mm Class II |
| 26 | 200mm Class II |
| 27 | 250mm Class II |
| 28 | 300mm Class II |
| 29 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 30 | Supplying, installation, testing & commissioning of non-returnvalve of following sizeconforming to IS :5312 complete with rubber, gaskets ,GI Bolts ,nuts washers etc as required |
| 31 | 150mm Dia |
| 32 | Providing, laying, testing & commissioning of\"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 33 | 150mm Dia |
| 34 | 200mm Dia(wall thickness 6.3mm) |
| 35 | 250mm Dia(wall thickness 6.3mm) |
| 36 | Providing and fixing bolts including nuts and washers complete.(Assorted Size) |
| 37 | Supplying & Replacingof the rubber gasket(Minimum thickness 4mm) with undermentioned size with new one inthe existing valves flange /Strainer (Nut & Bolt rate will be paid saperately) |
| 38 | Rubber Gaskets 100 mm dia |
| 39 | Rubber Gaskets 150 mm dia |
| 40 | Rubber Gaskets 200 mm dia |
| 41 | Rubber Gaskets 250 mm dia |
| 42 | Rubber Gaskets 300 mm dia |
| 43 | Rubber Gaskets 400 mm dia (For Strainer) |
| 44 | Providing& fixing MS Plate of requird size ,shape & thickness on exisiting strainer ,MS Tank & pipes etc including cutting , welding & making it leakage proof etc as required . |
| 45 | Collect the sample from site in presence deptt representative & Testing of water quality through ISO certified & NABL Approved labfor physical, chemical and bacteriozical parameters as per IS code 3328as required |
| 46 | Dismantling the covers 02 no of main Hole of existing horizontal type filter vessel of size i/c taking the whole filter media of assorted sizes from the filter vessel to outside swimming pool plant house & segregate different size & putting in empty cement bags etc complete as required. |
| 47 | Cleaning & rubbingof inner surface of side vessel with steel brush, wire & detergent etc complete as reqd |
| 48 | Painting of inner surface of filter vessel with anti corrosive primer & paints with 2 or more coats in approval shade etc complete as reqd. |
| 49 | Supplying and replacement of defective umbrella type filter Nozzle of 1/2 \"i/c dismantling & removing excising defective nozzles from header pipe etc complete as reqd i/c rebate /credit of old dismantle etc complete as reqd. |
| 50 | Supplying and filling of fresh filter media of silica sand of size 8/16 & 16/32 in the existing filter vessel etc complete reqd. |
| 51 | Washing of remaining filter media of size 4/8 & gravel through wire mesh net by water and filling back in the filter vessel of filtration plant etc complete as reqd |
| 52 | Closing of main hole cover of filter vessel 02 Nosas required i/c testing and commission of the filtration plant as reqd. |
| 53 | Supplying & fixing 400mm cross section dia strainer having 200mm dia welded 02Nos flanges on sidei/c credit for oldold dismantle strainer etc complete required . |
| 54 | P/F of DOL starter on the existing panel/wall(as per direction of Engg in charge) suitableupto 03 HP three phase induction motor model MK1Make L&T or equivalent BCH/Siemens/Havells including making incoming and outgoing connections with suitable size of thimbles testing etc as required. |
| 55 | P/FFully automatic star delta starter on the existing panel/wall(as per direction of Engg in charge) suitable for three phase 25 HPmotor having relay range 20-32 A of Cat No ML2FASD(Heavy Duty) Make L&T or equivalent BCH/Siemens/Havells including making incoming and outgoing connections with suitable size of thimbles testing etc as required. |
| 56 | Supplying, installation, testing and commissioning of 7.5 HPmulti stage submersible pump setsuitable forminimum LPM 125 discharge athead range 50 to 100mtr complete withcoupled totally enclosed electric motor suitable for 415 volt, 50 Hz, 3 phase A. C. supplyincluding water proof jointing of cables. (excluding lowering charges, lowering charges of submersible pumpset included in the item lowering of column pipe)( Make 6W10J7.5 Of Cromptonor similar inKIRLOSKAR, KSB, Texmo ) |
| 57 | Charges for Either lowering or Lifting of various capacity submersible pump set/Heavy Material/Machine either manually or using lifting machine including repalcement of old nut bolt, washer and gasket etc as reqd |
| 58 | Providing and laying in position cement concrete 1:2:4(1 cement : 2 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required. |
| 59 | Credit for old unserviceable Item like Suice valve ,NRV ,MS pipe ,flange etci/c dismantle from the site & weighing in presence of deptt representative as required . |
| 60 | Credit for old unserviceable Item like copper from motors etci/c dismantle & weighing in presence of deptt representative as required . |
| 61 | Dismentaling the existing Centrifugal Pump & Motor from base frame , removing rusted base frame from foundation , installing new MSbase frame made up at KBL Workshop or KBL Athorised Dealer ofPrimary steel C channel 6mm thick size 100mmx50mm as per standard of Make TATA(Weight of the frame should not be less than 42kg)with nessacerily required assecories suitable forundermentioned set of monoblock of Pump & Motor as perOEM Drawing for minimum vibration level & re-installing the existing Pump & Motorincluding connection the pipe ,cable , testing, complete as required, including credit for old scrap material which will be retained by the contractoras required . This complete work will be done through the OEM or OEM-authorized dealer of the pumps .(Rate for Foundation CC work will be paid saperately) |
| 62 | UP80/38 Pump or UP 125-30 + 25-30HP Induction Motor |
| 63 | Charges for Alignment Test by double gauge method carry through KBL or KBL authorised Dealer |
| 64 | Add 1.0633 multiplying factor for GST on DSR |
