Tender For Various Items Under Matching Grant Scheme As Listed Below, KANGRA-Himachal Pradesh

Tender For Various Items Under Matching Grant Scheme As Listed Below HDPE Pipe IS Standard 18:14151:2008 (Part-11) Nominal Outside Diameter (D) 19 mm. 13 mm, 25 mm, 38 mm, 50 mm Electric/Manual Chaff Cutter Motor Operated Chaff Cutter 1-2 HP electric motor (ISI Mark) along with pulley and wheel be wt(approx)-80 kg. ⚫ Mild Steel Handle with Wooden Grip, Diameter 15 men, total leng 500 mm, length of wooden grip 430-450 mm. Cutting Blades 2 to 3 Nos made from carbon Steel, which a adjustable. Cutting Assembly-2 Nos, cutting mouth made from cast iron. Fly wheel of V-Belt type 750-800 diameter, width 25 mm with circular hole of 10 mm at the centre to connect it to main shaft. ⚫ Worm gears should be 2 in number. Feed rollers-2 in number with length 207 mm and diameter 85 mm Feeding roller made from cast iron. • Feeding trough should be attached on rear of shear plate w detachable provision. ⚫ Chaff Cutting Capacity Electric -200 to 250 Kg por hour All the roating parts should be covered by safety guards. Manual Chaff Cutter Manually Operated Chaff Cutter ⚫ Mild Steel Handle with Wooden Grip, Diameter 15 mm, total length 500 mm, length of wooden grip 430-450 mm. Fly wheel of 840-900 mm diameter, width 75 mm with a circular hole of 10 mm at the centre to connect it to main shaft. ⚫ Worm gears should be 2 in number, one located at upper side and one at lower side of worm. Feed rollers should be 2 in number with length 207 mm and diameter 85 mm. Feeding trough should be attached on rear of shear plate with detachable provision. Half of the trough shall be covered for safety. ⚫ Stand should consist of four legs, leg support may be detachable. ⚫ Chaff Cutting Capacity: Electric-100 to 150 Kg per hour HDPE Pipe IS Standard IS:14151:2008 (Part-II) Nominal Outside Diameter (D) 19 mm. 13 mm, 25 mm, 38 mm, 50 mm Electric Cutter Chaff Motor Operated Chaff Cutter 1-2 HP electric motor (ISI Mark) along with pulley and wheel belt, wt(approx)-80 kg Mild Steel Handle with Wooden Grip, Diameter 15 mm, total length 500 mm, length of wooden grip 430-450 mm. • Cutting Blades 2 to 3 Nos made from carbon Steel, which are adjustable. ⚫ Cutting Assembly-2 Nos, cutting mouth made from cast iron. Fly wheel of V-Belt type 750-800 diameter, width 25 mm with a circular hole of 10 mm at the centre to connect it to main shaft. ⚫ Worm gears should be 2 in number. Feed rollers-2 in number with length 207 mm and diameter 85 mm. Feeding roller made from cast iron. ⚫ Feeding trough should be attached on rear of shear plate with detachable provision. Chaff Cutting Capacity > Electric -200 to 250 Kg per hour All the roating parts should be covered by safety guards. Manual Chaff Manually Operated Chaff Cutter Cutter Mild Steel Handle with Wooden Grip, Diameter 15 mm, total length 500 mm, length of wooden grip 430-450 mm. Fly wheel of 840-900 mm diameter, width 75 mm with a circular hole of 10 mm at the centre to connect it to main shaft. Worm gears should be 2 in number, one located at upper side and one at lower side of worm. • Feed rollers should be 2 in number with length 207 mm and diameter 85 mm. • Feeding trough should be attached on rear of shear plate with detachable provision. Half of the trough shall be covered for safety. Stand should consist of four legs, leg support may be detachable. Chaff Cutting Capacity > 150 Kg per hour Electric-100 to

Refer document

Refer document

Refer document