Tender For Construction Of Small Po Building At Harsud In Khandwa Division Under Indore Region Mp. 1 EARTH WORK 1.1 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. 1.1.1 All kinds of soil 50 cum 149.00 7450.00 1.2 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1.2.1 All kinds of soil. 39 cum 218.60 8525.00 1.3 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 1.3.1 All kinds of soil 1.3.1.1 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 20 metre 293.40 5868.00 1.4 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 36 cum 161.60 5818.00 1.5 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 227 cum 564.00 128028.00 1.6 Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. 1.6.1 All kinds of soil 1 cum 104.50 105.00 1.7 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 12 cum 2161.20 25934.00 Sub-Total 181728.00 2 CEMENT CONCRETE (CAST IN SITU) 2.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2.1.1 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 6 cum 7365.15 44191.00 2.1.2 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 35 cum 6050.65 211773.00 2.2 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 2.2.1 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 1 cum 9047.30 9047.00 2.3 Centering and shuttering including strutting, propping etc. and removal of form work for : 2.3.1 Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. 7 sqm 702.00 4914.00 2.4 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 16 sqm 681.65 10906.00 Sub-Total 280831.00 3 REINFORCED CEMENT CONCRETE 3.1 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 3.1.1 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) 30 cum 8364.20 250926.00 3.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fllets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: 3.2.1 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 5 cum 9861.70 49309.00 3.3 Reinforced cement concrete work in beams, suspended foors, roofs having slope up to 15* landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to foor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). 23 cum 10391.40 239002.00 3.4 Centering and shuttering including strutting, propping etc. and removal of form for 3.4.1 Foundations, footings, bases of columns, etc. for mass concrete 18 sqm 332.10 5978.00 3.4.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 28 sqm 702.00 19656.00 3.4.3 Suspended floors, roofs, landings, balconies and access platform 115 sqm 766.55 88153.00 3.4.4 Lintels, beams, plinth beams, girders, bressumers and cantilevers 99 sqm 608.35 60227.00 3.4.5 Columns, Pillars, Piers, Abutments, Posts and Struts 70 sqm 804.25 56298.00 3.4.6 Weather shade, Chajjas, corbels etc., including edges 12 sqm 814.95 9779.00 3.5 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 3.5.1 Thermo-Mechanically Treated bars of grade Fe-500D or more. 3976 kg 89.65 356448.00 3.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 3.6.1 Thermo-Mechanically Treated bars of grade Fe-500D or more. 3907 kg 89.65 350263.00 3.7 Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand). 196 sqm 253.05 49598.00 3.8 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 21 metre 64.70 1359.00 Sub-Total 1536996.00 4 MASONRY WORK 4.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 4.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand) 34 cum 6658.25 226381.00 4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 4.2.1 Cement mortar 1:6 (1 cement : 6 coarse sand) 18 cum 8288.35 149190.00 4.3 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 4.3.1 Cement mortar 1:4 (1 cement :4 coarse sand) 60 sqm 1018.05 61083.00 4.4 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 60 sqm 86.45 5187.00 4.5 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). 29 metre 55.80 1618.00 Sub-Total 443459.00 5 CLADDING WORK 5.1 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. 5.1.1 Granite stone slab of colour black, Cherry/Ruby red 5.1.1.1 Area of slab upto 0.50 sqm 6 sqm 4679.35 28076.00 5.2 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 5.2.1 Granite work 47 metre 418.85 19686.00 5.3 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 50 sqm 1063.45 53173.00 5.4 (a) Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium (c) composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. 22 sqm 4474.20 98432.00 Sub-Total 199367.00 6 WOOD AND P. V. C. WORK 6.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 6.1.1 Sal wood 0.17 cum 106720.85 18143.00 6.2 Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. 6.2.1 Sal wood 0.12 cum 97078.35 11649.00 6.3 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 6.3.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 9 sqm 2015.75 18142.00 6.4 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 9 sqm 401.40 3613.00 6.5 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 3 each 1025.65 3077.00 6.6 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 6.6.1 300x16 mm 6 each 260.30 1562.00 6.6.2 250x16 mm 4 each 234.90 940.00 6.7 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 6.7.1 200x10 mm 6 each 90.80 545.00 6.7.2 150x10 mm 4 each 75.55 302.00 6.8 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 6.8.1 125 mm 12 each 60.05 721.00 6.8.2 100 mm 8 each 53.25 426.00 6.9 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 6.9.1 Twin rubber stopper 6 each 62.25 374.00 6.1 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 6.10.1 1.0 mm thick 11 sqm 764.00 8404.00 6.11 Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in- charge (Frame work shall be paid for separately). 6.11.1 12mm thick commercial ply conforming to IS : 1328 BWR type 11 sqm 1084.60 11931.00 Sub-Total 79829.00 7 STEEL WORK 7.1 Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. 7 sqm 9397.35 65781.00 7.2 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 7.2.1 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 802 kg 142.30 114125.00 7.3 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 109 kg 612.25 66735.00 Sub-Total 246641.00 8 FLOORING 8.1 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 12 sqm 935.60 11227.00 8.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 8.2.1 Size of Tile 600x600 mm 57 sqm 1416.65 80749.00 8.3 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. 8.3.1 Size of Tile 600x600 mm 4 sqm 1466.50 5866.00 8.4 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 8.4.1 Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent 12 sqm 3908.80 46906.00 Sub-Total 144748.00 9 ROOFING 9.1 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 2 each 266.60 533.00 9.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 9.2.1 110 mm diameter 8 metre 319.75 2558.00 9.3 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion 9.3.1 Coupler 9.3.1.1 110 mm 2 each 119.95 240.00 9.3.2 Bend 87.5° 9.3.2.1 110 mm bend 2 each 132.00 264.00 9.3.3 Shoe (Plain) 9.3.3.1 110 mm Shoe 2 each 115.95 232.00 9.4 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 9.4.1 75 mm 3 each 309.50 929.00 9.4.2 110 mm 9 each 310.85 2798.00 Sub-Total 7554.00 10 FINISHING 10.1 12 mm cement plaster of mix : 10.1.1 1:6 (1 cement: 6 coarse sand) 176 sqm 294.35 51806.00 10.2 15 mm cement plaster on rough side of single or half brick wall of mix: 10.2.1 1:6 (1 cement: 6 coarse sand) 143 sqm 339.10 48491.00 10.3 20 mm cement plaster of mix : 10.3.1 1:6 (1 cement: 6 coarse sand) 13 sqm 401.35 5218.00 10.4 6 mm cement plaster of mix : 10.4.1 1:3 (1 cement : 3 fine sand) 5 sqm 253.05 1265.00 10.5 Neat cement punning. 23 sqm 67.80 1559.00 10.6 Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. 2 per bag of 50kg cement used in the mix 60.55 121.00 10.7 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification. 10.7.1 Two or more coats on new work 152 sqm 92.75 14098.00 10.8 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 10.8.1 Water thinnable cement primer 283 sqm 64.45 18239.00 10.9 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 10.9.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 224 sqm 162.35 36366.00 10.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : 10.10.1 Two or more coats on new work 131 sqm 137.85 18058.00 10.11 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 10.11.1 Two or more coats on new work 49 sqm 131.45 6441.00 10.12 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 131 sqm 123.85 16224.00 Sub-Total 217886.00 11 ROAD WORK 11.1 Supplying at site : 11.1.1 R.C.C. Standards post/ struts/rails/ pales of mix 1:1.5:3(1 cement : 1.5 coarsesand : 3 graded stone aggregate12.5 mm nominal size) with wooden plugs or 6mm barnibs wherever required as per direction of Engineer-incharge (cost of earth works in excavation, concrete worksin foundation to be paid separately). 1.2 cum 29105.40 34926.00 11.2 Fencing with R.C.C. post placed at required distance, embedded incement concrete blocks, every 15th post, last but one end post andcorner post shall be strutted on both sides and end post one sideonly, provided with horizontal lines and two diagonals of barbed wireweighing 9.38 kg per 100 metres (minimum), between the two postsfitted and fixed with G.I. staples on wooden plugs or G.I. binding wiretied to 6 mm bar nibs fixed while casting the post (cost of R.C.C.posts, struts, earth work and concrete to be paid for separately) :-Payment to be made per metre cost of total length of barbed wire used. 11.2.1 With G.I. barbed wire 829 metre 12.45 10321.00 11.3 Providing and laying tactile tile (for vision impaired persons as perstandards) of size 300x300x9.8mm having with water absorption lessthan 0.5% and conforming to IS:15622 of approved make in all coloursand shades in for outdoor floors such as footpath, court yard, multimodals location etc., laid on 20mm thick base of cement mortar 1:4(1 cement : 4 coarse sand) in all shapes & patterns including groutingthe joints with white cement mixed with matching pigments etc.complete as per direction of Engineer-in-Charge. 10 sqm 1719.00 17190.00 11.4 Providing and laying factory made chamfered edge Cement Concretepaver blocks in footpath, parks, lawns, drive ways or light trafficparking etc, of required strength, thickness & size/ shape, made bytable vibratory method using PU mould, laid in required colour &pattern over 50mm thick compacted bed of sand, compacting andproper embedding/laying of inter locking paver blocks into the sandbedding layer through vibratory compaction by using plate vibrator,filling the joints with sand and cutting of paver blocks as per requiredsize and pattern, finishing and sweeping extra sand. complete all asper direction of Engineer-in-Charge. 11.4.1 60mm thick cement concrete paver block of M-35 gradewith approved colour, design & pattern. 310 sqm 932.35 289029.00 Sub-Total 351466.00 12 SANITARY INSTALLATIONS 12.1 Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls andfloors wherever required : 12.1.1 W.C. pan with ISI marked white solid plastic seat and lid 3 each 5540.55 16622.00 12.2 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brasspillar taps, 32 mm C.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the wallswherever require: 12.2.1 White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap 3 each 1679.60 5039.00 12.3 Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto1 metre long with S.S. triangular plate to Eureopean type W.C. ofquality and make as approved by Engineer - in - charge. 3 each 299.35 898.00 12.4 Providing and fixing white vitreous china flat back or wall corner typelipped front urinal basin of 430x260x350 mm or 340x410x265 mmsizes respectively. 1 each 1382.30 1382.00 12.5 Providing and fixing mirror of superior glass (of approved quality) andof required shape and size with plastic moulded frame of approvedmake and shade with 6 mm thick hard board backing : 12.5.1 Rectangular shape 453x357 mm 3 each 1158.95 3477.00 12.6 Providing and fixing toilet paper holder : 12.6.1 C.P. brass 3 each 680.80 2042.00 12.7 Providing and fixing PTMT Waste Coupling for wash basin and sink,of approved quality and colour. 12.7.1 Waste coupling 38 mm dia of 83 mm length and 77mmbreadth, weighing not less than 60 gms 4 each 109.70 439.00 12.8 Providing and fixing PTMT Bottle Trap for Wash basin and sink. 12.8.1 Bottle trap 38 mm single piece moulded with height of270 mm, effective length of tail pipe 260 mm from thecentre of the waste coupling, 77 mm breadth with 25 mmminimum water seal, weighing not less than 263 gms 3 each 325.10 975.00 12.9 Providing and fixing PTMT liquid soap container 109 mm wide, 125mm high and 112 mm distance from wall of standard shape withbracket of the same materials with snap fittings of approved qualityand colour, weighing not less than 105 gms. 3 each 146.30 439.00 12.1 Providing and fixing PTMT urinal cock of approved quality and colour. 12.10.1 15 mm nominal bore, 80 mm long, 42 mm high and 30mmwide with BSP female threads weighing not less than 48 gms 1 each 149.95 150.00 Sub-Total 31463.00 13 WATER SUPPLY 13.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 13.1.1 25 mm nominal dia Pipes 2 metre 408.55 817.00 13.1.2 32 mm nominal dia Pipes 15 metre 500.95 7514.00 13.1.3 40 mm nominal dia Pipes 10 metre 674.35 6744.00 13.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls 13.2.1 20 mm nominal dia Pipes 16 metre 513.75 8220.00 13.2.2 25 mm nominal dia Pipes 7 metre 626.05 4382.00 13.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 13.3.1 25 mm nominal dia Pipes 10 metre 370.65 3707.00 13.3.2 50 mm nominal dia Pipes 3 metre 811.85 2436.00 13.4 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 13.4.1 25 mm nominal bore 2 each 532.35 1065.00 13.5 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 13.5.1 25 mm nominal bore 1 each 399.15 399.00 13.6 Providing and fixing uplasticised PVC connection pipe with brass unions : 13.6.1 45 cm length 13.6.1.1 15 mm nominal bore 7 each 85.20 596.00 13.7 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 1000 per litre 9.70 9700.00 13.8 Providing and fixing PTMT bib cock of approved quality and colour. 13.8.1 15mm nominal bore, 86 mm long, weighing not less than 88 gms 3 each 109.85 330.00 13.9 Providing and fixing PTMT stop cock of approved quality and colour. 13.9.1 15 mm nominal bore, 86 mm long, weighing not less than 88 gms 7 each 103.15 722.00 13.1 Providing and fixing PTMT grating of approved quality and colour. 13.10.1 Rectangular type with openable circular lid 13.10.1. 1 150 mm nominal size square 100 mm diameter of the inner hinged round grating 4 each 169.70 679.00 13.11 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. 3 each 96.75 290.00 13.12 Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 13.12.1 25mm nominal bore, weighing not less than 62 gms 2 each 100.55 201.00 Sub-Total 47802.00 14 DRAINAGE 14.1 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round UPVC Type-B Pipes including bed concrete as per standard design : 14.1.1 110 mm diameter UPVC Type-B Pipe 8 metre 895.50 7164.00 14.1.2 160 mm diameter UPVC Type-B Pipe 12 metre 1095.15 13142.00 14.2 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 14.2.1 100x100 mm size P type 14.2.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 3 each 2453.55 7361.00 14.3 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 14.3.1 300 mm dia. R.C.C. pipe 5 metre 902.05 4510.00 14.4 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : 14.4.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 14.4.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 3 each 11687.10 35061.00 14.5 Extra for depth for manholes : 14.5.1 Size 90x80 cm 14.5.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 1 metre 8127.45 8127.00 14.6 Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : 14.6.1 With 20x20 mm square bar 2 each 461.35 923.00 14.7 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 14.7.1 L D- 2.5 14.7.1.1 Rectangular shape 600x450 mm internal dimensions 2 each 1255.25 2511.00 14.8 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 14.8.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 1 each 28029.15 28029.00 Sub-Total 106828.00 15 ALUMINIUM WORK 15.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 15.1.1 For fixed portion 15.1.1.1 Powder coated aluminium (minimum thickness of powder coating 50 micron) 50 kg 466.30 23315.00 15.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 15.1.2.1 Powder coated aluminium (minimum thickness of powder coating 50 micron) 50 kg 553.55 27678.00 15.2 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 15.2.1 With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 15 sqm 1019.80 15297.00 Sub-Total 66290.00 16 WATER PROOFING 16.1 Grading roof for water proofing treatment with 16.1.1 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) 9 cum 7510.75 67597.00 16.2 Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. 87 sqm 474.15 41251.00 Sub-Total 108848.00 17 STRUCTURAL GLAZING ALUMMINIUM COMPOSITE PANEL 17.1 Providing and supplying aluminium extruded tubular and otheraluminium sections as per the architectural drawings and approvedshop drawings , the aluminium quality as per grade 6063 T5 or T6 asper BS 1474,including super durable powder coating of 60-80 micronsconforming to AAMA 2604 of required colour and shade as approvedby the Engineer-in-Charge. ( The item includes cost of material suchas cleats, sleeves, screws etc. necessary for fabrication of extrudedaluminium frame work. Nothing extra shall be paid on this account).The weight of aluminium extruded section shall be taken for purposeof payment. 21 kg 370.45 7779.00 Sub-Total 7779.00 18 NEW TECHNOLOGIES AND MATERIALS 18.1 Providing an fixing factory made single extruded WPC (Wood Polymer Composite) solid wood/ window/ clerestory window frames/ chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750kg/cum, screw withdrawal strength of 2200N (face) & 1100N (edge), minimum compressive strength of 58N/mm2 and modulus of elasticity 900N/mm2 and resistance of spread of flame of class A category with property of being termite/ borer proof, water /moisture proof and fire retardant and fixed in position with M.S. hold fast/ lugs/ SS dash fasteners of required dia and length complete as per direction of Engineer in Charge, (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately) Note: For WPC (Wood Polymer Composite) solid wood/ window frames minus 5mm tolerance to dimensions i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 18.1.1 Frame size 45x 70mm 20 metre 632.25 12645.00 18.2 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 18.2.1 30 mm thick 6 sqm 3954.00 23724.00 Sub-Total 36369.00 19 MARKET RATE ITEMS 19.1 Providing & fixing of customer writing ledge of size 1220mm long, 400mm wide and 1450mm high with writing top at a height of 1050mm including open drawers of 100mm depth for keeping papers below the working top as per architectural drawing No.B1 to B5. The writing ledge shall be made with 19mm thick block board conforming to IS 1659/1979 bonded with phenol formaldehyde synthetic resin of IS 840/1974 of approved make Duro/Century/Green/Archidiam or equivalent including backing also of 19mm thick block board of full height of 1450mm. The ledge shall be laminated with 1.00mm thick decorative laminate of Greanlam /Virgolam/Archidiam on all visible surfaces from outside as well as inside and all hidden surfaces shall be painted with white synthetic enamel paint over priming coat of approved quality. All exposed edges of block board shall be covered by 19mm wide and 3mm thick 2nd class teak wood margin including matching the same. A stainless steel dustbin of 450mm height shall also be provided as per drawing. The dustbin shall be made of 1mm thick stainless steel sheet (SS-304 Grade) with necessary argon welding wherever required. The work shall include cost of all operations, labour and material, adhesive, nails, stainless steel screws etc. including approval of samples all completed as per direction of Engineer-in-charge. 1 each 10816.00 10816.00 19.2 Providing and fixing wooden customer service counter of size 1500mm length and 300mm width having height of 1050mm with attachment of working top having height of 750mm and of L shape having legs of 1500mmx300mm and 1350mmx450mm with tape rings all joints of legs including arrangement of computer system as keyboard, slit for printer paper etc. complete as per drg. No.A1 to A6. The two numbers stainless steel rectangular tube of size 25mmx50mm of 2mm thick having height of 2100mm fitted with counter to support the overhead signage panel as per drg. The counter shall be made of following ingredients : (a) The 19mm thick block board conforming to IS 1659/1979 bonded with phenol formaldehyde synthetic resin of IS 840/1974 of approved make Duro/Century/Green/Archidiam or equivalent shall be used to prepare Counter & decorative laminate on outer face and inside face finished with white synthetic enamel paint over priming coat of approved quality. (b) The edges of board shall be covered by 19mm wide and 3mm thick II class teak wood margin and matching the same. (c) The keyboard and drawer shall be fitted with a pair of 300mm long powder coated telescopic channels of approved brand. (d) The shutter below drawer in the counter shall be fitted with M.S. piano type hinges ISI marked conforming to (e) The shutter of counter shall be provided with 2 Nos. magnetic catcher of heavy duty (twin strip) horizontal type best quality, 3 Nos. multipurpose cabinet lock of Godrej make or equivalent and 4 Nos. brass finished stainless steel handle of 75mm long of best quality. The work shall include all operations, labour and materials, adhesive, nails and stainless steel screws etc. including approval of sample complete as per drg. and direction of engineer-in-charge. 3 Each 36000.00 108000.00 19.3 Providing and fixing storage cupboards as per drawing No.C1 to C4. The cupboard shall be fabricated with following material and operation : a) The 19mm thick block board conforming to IS 1659/1979 bonded with phenol formaldehyde synthetic resin of IS 840/1974 of approved make Duro/Century/Green/Archidiam or equivalent shall be used to prepare the cupboard. b) All exposed outer surface of whole cupboard shall be laminated with 1.00 mm thick decorative laminate of Greenlam/Virgolam/Archidiam and inside, backside and bottom surface shall be finished with white synthetic enamel paint over priming coat. The paint and primer shall be of approved quality. c) All exposed edges of ply shall be covered with 18 mm wide and 3 mm thick 2nd class teakwood margin including matching the same. d) The 18 mm thick cupboard shutter shall be fitted with IS : 12817 marked S.S. butt hinges of size 75 x 47 x 1.80 mm with S.S. screws. 19.3.1 (i) Storage cupboard of size 1220mm x 400mm x 1050mm containing three boxes with magnetic catcher of heavy duty and horizontal type (triple strip), brush finish stainless steel handles of suitable size (75mm or 100mm) and multipurpose cabinet lock of Godrej or equivalent in each box as per drawing and direction of Engineer-in-charge. The work shall include cost of all operations, labour and materials, adhesive, nails, stainless steel screews etc. as above including approval of sample as per direction of Engineer-in-charge. Note :- Nomenclature of item shall supersede over the drawings in case of any ambiguity between the two. 1 Each 11430.00 11430.00 19.3.2 (ii) Storage cupboards of size 799mm x 400mm x 1050mm containing two boxes with magnetic catcher of heavy duty and horizontal type (triple strip), brush finish stainless steel handles of suitable size (75mm or 100mm) and multipurpose cabinet lock of Godrej or equivalent in each box as per drawing and direction of Engineer-in-charge. The work shall include cost of all operations, labour and materials, adhesive, nails, stainless steel screws etc. as above including approval of sample as per direction of Engineer-in-charge. Note :- Nomenclature of item shall supersede over the drawings in case of any ambiguity between the two. 3 Each 8175.00 24525.00 19.4 Providing & fixing UPVC soil, waste & vent pipe conforming to IS : 13592 Type B of approved brand with necessary solvent etc complete as per direction of Engineer In charge. 19.4.1 75 mm diameter 13 metre 432.00 5616.00 19.4.2 110 mm diameter 14 metre 622.66 8717.00 19.4.3 160 mm diameter 12 metre 898.34 10780.00 19.5 Providing & fixing moulded fittings conforming to IS : 13592 Type B of approved brand with necessary solvent etc complete as per direction of Engineer In charge. 19.5.1 Single Tee with door. (a) 75x75x75 mm. 3 each 188.87 567.00 19.5.2 Single Tee with door. (b) 110x110x110 mm. 3 each 372.30 1117.00 19.5.3 Vent Cowl. (a) 75 mm. 6 each 80.94 486.00 19.5.4 Vent Cowl. (b) 110 mm. 3 each 103.23 310.00 19.5.5 Nani trap of self cleansing design 110 mm to 75 mm 7 each 211.16 1478.00 19.5.6 Plain bend with door with 87.5 degree. (a) 75 mm. 3 each 145.47 436.00 19.5.7 Plain bend with door with 87.5 degree. (a) 110 mm. 3 each 226.41 679.00 Sub-Total 184957.00 Total 4280841.00 Add Difference of GST @ 6.33% (GST Raised from 12% to 18%) @6.33% on SR&DR Total 40,95,884.00 259269.00 Total 4540110.00 Less Cost Index @2% on SR&DR Total 43,55,153.00 -87103.00 Grand Total 4453007.00 SH- I (Wiring) 1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable i/c making good the damages up to its original finish etc as required.(Accessories to be used of MK Blanze /Legrand Aretior/Anchor Vision ) 1.1 Group C 44 Points 1467.00 Point 64548.00 2 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit i/c making good the damages up to its original finish as required 2.1 2x1.5 sq mm+1x1.5 sqmm earth wire 45 Meters 233.00 Meter 10485.00 2.2 4x1.5 sq mm+2x1.5 sqmm earth wire 35 Meters 326.00 Meter 11410.00 2.3 6x1.5 sqmm +3x1.5 sqmm earth wire 22 Meters 430.00 Meter 9460.00 2.4 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 40 Meters 334.00 Meter 13360.00 2.5 4 X 4 sq. mm + 2X 4 sq. mm earth wire 30 Meters 537.00 Meter 16110.00 2.6 2x6 sqmm +1x6sqmm earth wire 5 Meters 439.00 Meter 2195.00 2.7 4x6 sqmm +2x6sqmm earth wire 5 Meters 754.00 Meter 3770.00 3 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/PVC conduit as required. 3.1 2 x 1.5 sq. mm 15 Meters 95.00 Meter 1425.00 3.2 3 x 1.5 sq.mm 15 Meters 181.00 Meter 2715.00 3.3 6 x 1.5 sq.mm 15 Meters 285.00 Meter 4275.00 3.4 3x 4 sqmm 10 Meters 206.00 Meter 2060.00 4 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit i/c making good the damages up to its original finish as required.(M/s precision make orS.S) 4.1 20 mm 45 Meters 128.00 Meter 5760.00 4.2 25 mm 45 Meters 145.00 Meter 6525.00 5 S/f following modular type switch/socket or accessories on the existing switch box/cover i/c connections etc as reqd.(Accessories to be used of MK Blanze /Legrand Aretior/Anchor Vision ) 5.1 5/6 amps switch 10 Nos 103.00 Each 1030.00 5.2 3 pin 5/6 amps socket 25 Nos 122.00 Each 3050.00 5.3 15/16 amps switch 6 Nos 156.00 Each 936.00 5.4 6 pin 15/16 amps socket outlet 2 Nos 197.00 Each 394.00 5.5 Modular Blanking plate 5 Nos 40.00 Each 200.00 5.6 Stepped type electronic fan regulator (2M) 7 Nos 369.00 Each 2583.00 5.7 3.0 mm thick phenolic laminated sheet ISI mark. 1000 Sq Inchs 2.00 Sq Inch 2000.00 5.8 Single Information outlet w/o faceplate 5 Each 636.00 Each 3180.00 5.9 Modular Indicator Red 4 Each 91.00 364.00 5.1 25Amp AC motor Starter 3M 1 Each 1005.00 Each 1005.00 5.2 2mm thick Sheet Steel sheet i/c cutting/ drilling holes in required shape and size 500 Sq inch 7.00 Sq inch 3500.00 5.3 Telephone socket outlet 1 Nos 109.00 Each 109.00 6 Supplying and fixing following size modules, GI box (PVC in case of Surface) alongwith modular base & cover plate for modular switches in recess etc as required.(Accessories to be used of MK Blanze /Legrand Aretior/Anchor Vision ) 6.1 1 or 2 Module (75mmX75mm) 10 Nos 298.00 Each 2980.00 6.2 3 Module (100mmX75mm) 2 Nos 327.00 Each 654.00 6.3 4 Module (125mmX75mm) 1 Nos 343.00 Each 343.00 6.4 6 Module (200mmX75mm) 1 Nos 402.00 Each 402.00 6.5 8 Module (125mmX125mm) / (75mmX225mm) 5 Nos 454.00 Each 2270.00 6.6 12 Module (200mmX150mm) 1 Nos 547.00 Each 547.00 7 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings)..(Accessories to be used of MK Blanze /Legrand Aretior/Anchor Vision ) 3 Nos 477.00 Each 1431.00 8 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connectionetc. as required..(Accessories to be used of MK Blanze /Legrand Aretior/Anchor Vision ) 6 Nos 586.00 Each 3516.00 9 Supplying and Drawing following pair 0.5sqmm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface/recessed steel/PVC conduit etc as reqd(M/s polycabor S.S) 9.1 2 pair 40 Meter 38.00 Meter 1520.00 10 Supplying and fixing metal box of following sizes (N.S) on surface or in recess with suitable size of phenolic laminated sheet cover in the front i/c panting etc as required. 10.1 100mm X 100mm X 60mm 4 Nos 209.00 Each 836.00 10.2 180mm X 100mm X 60mm 4 Nos 245.00 Each 980.00 10.3 200mm X 250mm X 60mm 2 Nos 468.00 Each 936.00 SH II (Fans & Fittings) 11 P/f MS fan hook S fabricated out of 12 mm thick round steel bar for installation of ceiling fan i/c cutting the ceiling and repairing the same or If roog is of Shade type the fan to be modified as per truss/ structure pipe etc. as required.( In case of new RCC Slab casting, agency will provide 150mm Dia 16SWG MS fan box with 3mm thick phenolic sheet i/d 12mm thick round steel bar for installation of ceiling fan ) 8 Nos 273.00 Each 2184.00 12 SITC of 1400 mm sweep ceiling fan etc. as reqd. (M/s. CG High speed or equivalent model of Orient or Havells make) 8 Nos 2336.00 Each 18688.00 13 SITC of following energy efficient white LED fixture/ luminaire etc complete as reqd. 14 SITC of following type MS white powder coated LED Batten / mounting rail suitable for T5/T8 LED lamps having plastic end caps suitable for operation at 230Volts 50 Hz AC suppy etc as reqd . (Make Philips TMC 501 P 1xT-LED 22W P3241 & TMC 501 P 2xT-LED 22W P3242 /Similar superior model of make Wipro/ Havells/ CG/ Jaquar). 14.1 Single LED Lamp 25 Nos 615.00 Each 15375.00 14.2 Double LED Lamp 4 Nos 711.00 Each 2844.00 15 Supplying and fixing T8 retro LED tube 1200mm length having aluminium housing and PC diffuser in the existing T8 fitting suitable for 230Volts 50 Hz AC suppy complete etc as reqd (Make: Jaquar LTBL01X020XC /Similar superior model of make Wipro/ Havells/ CG/ Philips) 33 Nos 404.00 Each 13332.00 16 1x9 watt 2 feet LED batten having aluminium base and inbuilt driver suitable for operation at 230 Volts 50 Hz AC supply etc as reqd (Wipro /Philips /Crompton make ) 5 Nos 425.00 Each 2125.00 17 S/F of 225 mm sweep Exhaust fan Heavy Duty with double ball bearing, 4 blade , with bird guard complete as required. (M/s. M/s CG Transair / Almonard medium duty, Havells ventilair or equivalent model of SS make) 3 Each 2388.00 Each 7164.00 SH III (Main Board And SDB s) 18 S/f following way, single pole and neutral/triple pole and neutral , sheet steel, MCB distribution board, 240 /415volts, on surface/recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc as required. (But without MCB/RCCB/isolator) 18.1 2 Way Enclosure 1 Nos 482.00 Each 482.00 18.2 6 Way, Double door 1 Nos 2206.00 Each 2206.00 18.3 8 Way, Double door 1 Nos 2573.00 Each 2573.00 18.4 12Way SPN Double door 1 Nos 2315.00 Each 2315.00 18.5 4Way(4+12), Double Door 1 Nos 4091.00 Each 4091.00 19 S/F 5 Amps to 32 Amps rating, 240/415 volts, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc as required. 19.1 Single pole 30 Nos 256.00 Each 7680.00 19.2 40 Amp Double pole 3 Nos 920.00 Each 2760.00 19.3 40 A FP MCB 2 Nos 1910.00 Each 3820.00 20 Supplying of following size XPLE insulated PVC outer sheathed aluminium conductor armoured cable confirming to IS 7098( Part I) /1988 suitable for operation on1.1 KV grade as reqd 20.1 2x6 sqmm 60 Meter 103.00 Meter 6180.00 20.2 4x16Sqmm 30 Meter 174.00 Meter 5220.00 21 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation and refilling the trench etc. as required, but excluding sand cushioning and protective covering. 21.1 Upto 35 sq. mm 20 Meter 200 Meter 4000.00 22 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required. 22.1 Upto 35 sq. mm 20 Meter 37 Meter 740.00 22 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on wall surface as required. 22.1 Upto 35 sq. mm 50 Meter 55 Meter 2750.00 23 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 23.1 2x6 sqmm 8 Sets 240 Set 1920.00 23.2 4x16sq. mm (28 mm) 6 Sets 309 Set 1854.00 24 Supplying and fabricating of 16 SWG MS sheet i/c cutting, bending, drilling ,welding powder painting etc as reqd 1 SQM 1200 SQM 1200.00 SH-IV ( Earthing) 25 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. 3 Sets 7472 Set 22416.00 26 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. 30 Meter 706 Meter 21180.00 27 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. 30 Meter 244 Meter 7320.00 28 Providing and fixing 8 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. 200 Meter 21 Meter 4200.00 29 Supplying and fixing 50mm X 5 mm thick GI Earth Bar of 300mm long with two Nos Insulation Drum and 8 Nos Hole in Earth bar etc complete as required Nos 280 Each 30 SITC of 63 Amp On load Change over switch in sheet steel enclouser suitable for operattion at 415 Volts 50 Hz AC supply etc as reqd( L&T make model no CO10630OSOO or S.S) 1 Nos 7628 Each 7628.00 31 SITC of 63 Amp TPN SDFU (Main switch) with suitable HRC fuse suitable for operation 415 Volts 50 Hz AC supply etc as reqd (L&T make FN 63 TPN / FP CE* or S.S) 1 Nos 6148 Each 6148.00 32 Providing and fixing (ISI Marked)(IS:2878)portable fire extinguiser ,carbon di oxide (co2) type flat base including valve , discharge hose pipe of not less than10mm Zdia and 1.0 Mlongand omplete in all respect including initial refilling with co2 gas onfirming to IS:307-1966 filled to filling ratio not more than 0.667 and wall suspension bracket etc as reqd ( Safex/Kanex/Fire Fite) 32.1 4.50 kg Capacity 2 Nos 6200 Each 12400.00 SH-V ( LAN Wiring) & CCTV 33 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 33.1 1 run of cable 25 Meter 57 Meter 1425.00 33.2 2 run of cable 20 Meter 96 Meter 1920.00 33.3 3 run of cable 25 Meter 134 Meter 3350.00 34 Supply of following equipments/accessories for local area networking of computers through database servers complete as reqd(M/s D-Link/SS make) 34.1 Patch cord Cat-6 ( factory crimped 2 Mtr) 4 Nos 267 Each 1068.00 35 S/F cable management system of following size with accessories as reqd on surface as reqd (M/sPresicion/ MK make) 35.1 32mm x 12.5mm 3 Meters 74 Meter 222.00 35.2 50mm x 50mm 3 Meters 241 Meter 723.00 36 S/F Wall Mount 19 12U Rack having 600 mm depth along with all accessories, etc as reqd (for Networking/ DVR/ DVR SMPS) 1 Nos. 7,720 Each 7720.00 SH-VII ( COMPOUND LIGHT & Misc 37 SITC of 25Watt LED type street light fitting ( IP 65 protection)made of diecast Aluminim housing with corrosion resistance polycarbonate cover, Electronic driver having efficacy of 100lm/wat , CCT 5700K i/c p/f 1.2 meter long 32mm Dia GI/ MS bracket (welding directly to C/L Pole with 6mm MS sheet as support in case of fixing on pole) with two coats red oxide and two coats of white enammelled synthetic painting , etc as reqd(M/s Philips Greenline Smart BRP042 25LED HP/CW 240V / Crompton greaves as per direction of Engineer- in Charge ) 5 Nos 3682 Each 18410.00 38 S/f weather proof front operated PVC box M/s Syntex of aprx size 230mm x170mmx105mm deep with locking arrangement & 4 way backelite connector with 1 no 1Amp SP MCB i/c connection with 3 core 1.5sqmm PVC insulated PVC sheathed copper conductor cable upto fitting i/c testing , sign writing etc as reqd. 5 Nos 950 Each 4750.00 39 SITC of 1.0HP/0.75KW, single phase Phase Open well Submercible pump set,capable to discharge 120LPM to 290LPM at head range 22.0-14.0 Mtr. Head having 2800 RPM with control panel of the pump with 5.0 m long power chord and footvalve bend and stainer i/c connnection etc comp as reqd.(Model No.Lubi LHL151* Make or similar capacity of /Kirloskar KOS135i or SS make) 1 Nos 13972 Each 13972.00 40 S/f 3x2.5 Sqmm PVC insulated PVC sheathed copper conductor Flat Submersible Cable suitable for 415Volt 50Hz AC supply etc as reqd. (M/sPolycab) 25 Meter 137 Meter 3425.00 41 S/f following accessories for pump set i/c making proper connection for delivery / suction/control etc as reqd ( ISI Make) 41.1 25 mm cPVC Ball valve 1 Nos 434 Nos 434.00 41.2 25 mm CPVC Pipe SDR 11 with all required accessories 25 Meter 397 Meter 9925.00 42 Providing, laying and fixing following dia G.I. pipe (medium class) in ground/ Roof complete with G.I. fittings including trenching (75 cm deep)and re-filling, if laid in ground or providing clamps if fixed in between wall for fixing cable trays / Fans etc as reqd etc as required 42.1 40mm Dia 10 Meter 428 Meter 4280.00
