Indian Oil Corporation Limited-IOCL has published Tender For Painting Work On Station Piping And Steel Structure At Nrpl, Panipat Pump Station. (Pnp23026). Submission Date for this Tender is 16-08-2023. Painting Tenders in panipat Haryana. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Painting work on station piping and stee |
| 2 | Lettering with black Japan paint of approved brand and manufacture. [Note: Unit "EA" shall mean "PER LETTER PER CM HEIGHT"].mposite 100:0 |
| 3 | Black anti-corrosive bitumastic paint: Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to givean even shade : Old work (one or more coats). |
| 4 | Aluminium paint: Painting with aluminium paint of approved brand and manufacture to give an even shade : One or more coats on old wo rk.Composite 100:0 |
| 5 | Synthetic enamel paint: Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more co ats on new work |
| 6 | Red oxide zinc chromate primer : With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanis ed iron/ steel works. Composite 100:0 |
| 7 | Surface preparation using hand tool cleaning including removal of oil, grease and other contaminants by solvent cleaning followed byremoval of defective paint, loose mill scale, loose rust, loose paint, weld flux, slag from the metallic surfaces, by hand chipping , hand brushing, hand scrappers / chisels, steel wools, final cleaning with high pressure ( 10000 PSI ) low TDS fresh soft water jetcleaning and drying with compressed air as per the specifications and directions of Site Engineer. Prepared surface shall conform t o WJ-4 /ST-2as per NACE no.5/SSPC SP-12 standards. |
| 8 | Sweep blasting (NACE No. 4):- Abrasive (Copper Slag blasting) blasting of piping (all sizes / all heights) conforming to SSPC-SP 7/N ACE No. 4 (brush off / sweep blasting). This item is inclusive of providing all required manpower, tools, tackles, consumables, non- consumables, equipments etc. to complete the work in all respects as per technical specifications and instructions of EIC/ Site Engi neer. |
| 9 | Wet abrasive blasting : Wet Abrasive blast cleaning of of piping (all sizes / all heights) conforming to Swedish standard SA 2.5 sta ndard. This item is inclusive of providing all required manpower, tools, tackles, consumables, non-consumables, equipments etc. to c omplete the work in all respects as per technical specifications and instructions of EIC/ Site Engineer. |
| 10 | Dry abrasive blasting NACE No. 2 :- Surface preparation of piping (all sizes / all heights)using water washing (WJ4) with low TDS potable sweet water followed by copper slag blasting (conforming to SA 2.5 surface finish) and profile of 40 to 70µm inclusive of al l required water, abrasives, equipments, manpower, consumables, tools, tackles, consumables, non-consumables to complete the work inall respects as per specifications and instructions of the EIC/ Site Engineer. |
| 11 | Applying priming coat with ready mixed primer of approved brand and manufacturer at all heights over steel surfaces like structures,columns, pipes, vessels, tanks etc. as per manufacturers specifications and directions of the Engineering-in-Charge; all complete i ncluding cleaning the surface using emery papers/Power tool cleaning such as ST-2 or ST-3 as per requirement, including all material , consumables, tools, tackles, labour etc but excluding Scaffolding. Note- No. of coats mentioned in the SOR items are only indicati ve and contractor has to achieve rquired DFT by applying more coats (if required) within the relevant SOR item rates. - Self primingHB coating primer to achive a minimum DFT of 100- 125 microns (1 or more coat of 100-125 µ) |
| 12 | "Supplying & Applying various epoxy and other protective intermediate / finish paints of approved brand and manufacturer at all heig hts over prepared/primed surface for steel structures, pipelines, tanks, equipments, concrete floors etc. as per manufacturers speci fication & directions of Engineer-in-charge and; all complete including all materials, labours, tools-tackles and consumables etc bu t excluding Scaffolding. Note- No. of coats mentioned in the SOR items are only indicative and contractor has to achieve required DF T by applying more coats (if required) within the relevant SOR item rates. - Two pack Acrylic Poly-urethane (PU) to achive a minimumDFT of 40-50 microns (one or more coat of 40- 50 µ)." |
| 13 | Surface preparation/ cleaning of surface using hand brush/emery paper etc. including removal of oil/grease/blister etc, and make thesurface ready for primer/painting. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
