|
| 1 | Demolition of lime concrete or cement conrete of any description in ground floor and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 2 | Material and labour for broken stone hard core of gauge not exceeding 63mm, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and levelled in layer not exceeding 15cm thick watered and rammed to a true surface complete all as specified and directed. |
| 3 | Material and labour for 50mm thick PCC (1:3:6) type C-1 using 20mm graded mechanically crushedstone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with 85/25 grade bitumen and sand (1:3 ratio) mixture etc complete all as specified and directed. |
| 4 | Material and labour for 25 mm thick cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) as in levelling course complete all as specified and as directed. |
| 5 | Material and labour for 40mm thick PCC 1:2:4 type B1 using 20mm graded mechanically crushed stone aggregate as in floors and finishing the concrete surface even and smooth without using extra cement complete all as specified and directed. |
| 6 | Supply and fixing of glass dividing strips 3mm thick and 38mm wide inserted in position and confirm to design complete all as specified and directed. |
| 7 | Supply and fixing for heavy duty tiles (coloured), good grip series, size 300 mm x 300 mm x 10 mm thick, pattern as approved by Engineer-in-Charge, set, jointed and pointed in neat cement slurry @ 3.00 kg/square metre, laid over and including 20 mm thick (average thickness) cement mortor (1:4) bedcomplete all as specified and directed.(Note: Design/pattern shall be as approved by GE before execution of work) |
| 8 | Material and labour for brick work with sub class ‘B’ bricks, straight or curved on plain exceeding 6 metre mean radius in cement mortar (1:6) including demolition of brick work built in cement mortar including demolition of old brick/stone masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed. |
| 9 | Material and labour for brick work (except bricks)straight or curved on plan exc 6 metre mean radius built in CM 1:6 (old size brick)including demolition of old brick /stone masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed. Note : Old serviceable brick obtained from demolition shall be reused.The rate quoted against this item is inclusive of necessary cleaning and stacking of bricks before incorporation in the work. |
| 10 | Material and labour for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in coppings, benching, kerbs, edges etc including necessary form work complete all as specified and directed. |
| 11 | Taking down cement plaster on brick or stone walls or concrete surfaces, etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 12 | Material andlabour for 15 mm thick rendering in cement mortar (1:6)on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement including preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer on wall complete all as specified and directed. |
| 13 | Material andlabour for 15mm thick rendering in cement mortar (1:4)on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement with and including two coats of cement base paint over a coatof primer complete all as specified and as directed. |
| 14 | Material andlabour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including15mm thick screed bed or layer in cement mortar (1:4) including dismantling of existing tiles etc including cement mortar bedding (but not backing) andrubbish off the premises complete all as specified and directed. |
| 15 | Material andlabour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar (1:3) including dismantling of existing tiles etc including cement mortar bedding (but not backing) andrubbish off the premises complete all as specified and directed. |
| 16 | Material and labour forpremium quality coloured glazed ceramic tiles (350x250mm/450x350mm 7 to 8mmthick)as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the shade of tiles overand including rendering 10mm thick in cement plaster 1:3 finished rough surface to receive tiles including dismantling of existingwall tiling including cement mortar bedding (but not backing) andrubbish off the premises complete all as specified and directed. |
| 17 | Material andlabour for premium quality, light shade vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed as in neat, neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including15mm thick screed bed or layer in cement mortar (1:4) including dismantling of existing tiles etc including cement mortar bedding (but not backing) andrubbish off the premises complete all as specified and directed. |
| 18 | Material andlabour for premium quality, light shade vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm as in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar (1:3) including dismantling of existing tiles etc including cement mortar bedding (but not backing) andrubbish off the premises complete all as specified and directed. |
| 19 | Material and labour for 18 to 20mm thick Granite stone of black shade work (table rubbed, polished & moulding), as in floors, cooking platforms and like bedded with and including 15 mm thick screed bed in CM (1:4) and jointed with grey cement slurry @ 3 Kg/Sqm, and pointed with white with admixture of pigment to match with shade of granite stone including grinding and polishing including dismantling of existing stoneslabs including cement mortar bedding (but not backing) andrubbish off the premises complete all as specified and directed. |
| 20 | Material and labour for 18 to 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, skirting, on vertical surface and like in 10mm thick rendering in CM (1:3) and jointed with grey cement slurry @ 3 Kg/Sqm, and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding, moulding and polishing on edges etc including dismantling of existing stone /tiles etc including cement mortar bedding andrubbish off the premises complete all as specified and directed. |
| 21 | Material andlabour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, 8 to 9 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including15mm thick screed bed or layer in cement mortar (1:4) including dismantling of existing tiles etc including cement mortar bedding (but not backing) andrubbish off the premises complete all as specified and directed. |
| 22 | Material andlabour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, 8 to 9 mm thick as in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar (1:4) including dismantling of existing tiles etc including cement mortar bedding (but not backing) andrubbish off the premises complete all as specified and directed. |
| 23 | Material and labour for preparation of old decorative surface of wall etc by washing rubbing down including scrapping and applying one coat of cement base paint of any tint complete all as specified and directed. |
| 24 | Material and labour for preparation of old decorative surface of wall including washing rubbing down and stopping of distempered and painted surfaces and applying one coat of oil emulsion paint complete all as specified and as directed. |
| 25 | Material and labour for preparing surfaces old plastered surfaces of walls and applying one coat of white washing complete as all specified and directed. |
| 26 | Material and labour for 75mm thickPCC (1:4:8) type D-2 using 40mm graded mechanically crushed stone aggregateas in sub base of floor, hard standing etc complete all as specified and directed. |
| 27 | Material and labour for providing and laying factory made PVC moulded, dark red/yellow coloured with grey cement and red pigment, glossy finished, vibrated machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete including dismanteling of existing tiles/slab of any discription any type and sub base of the premises complete all as specified and directed. |
| 28 | Material and labour for providing and laying factory made PVC moulded, dark red/yellow coloured with grey cement and red pigment, glossy finished, vibrated machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade, over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete including dismanteling of existing tiles/slab of any discription any type and sub base of the premises complete all as specified and directed. |
| 29 | Material and labour for providing and laying of precast cement concrete solid concrete block, type B-1, 1:2:4 (using 20mm graded stone aggreagate) confirming to IS 2185 (Part-I) 2005 of 45/30 cm high, 10 cm thick and of suitable width including chamfers, weatherings, throating etc as in kerb continuous edging jointed in cement mortar 1:4 and struck flush pointing as the work proceeds and finishing with neat cement flush joint etc including demolition of existing concrete work of any description complete all as specified and directed. |
| 30 | Supply and fixing in repair of vitreous china wash hand basin white flat back of size 550x440mm including CI brackets and 15mm chromium plated pillar tap cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, PVC connection 450 mm long having PTMT nuts and 32 mm dia brass chromium plated waste coupling and making good to disturbed portion including32 mm dia PVC waste pipe etc., complete all as specified and directed. |
| 31 | Supply and fixed in repair ofvitreous china wash down water closet pedestal pattern (EWC), White including connection to trap and to flushing pipe with ‘P’ or ‘S’ trap, making good to floor, plastic water closet seat cover with mild steel chromium plated hinges and chromium plated jet spray with 1.5 meter flexible LDPE pipe jointed with pipe complete all as specified and directed. |
| 32 | Supply and fixing in repair of 10 litre capacity virgin polypropylene cistern, white at low level complete with 32 mm bore PVC flush pipe of suitable length, PVC connection 450 mm long having PTMT nuts including bracket and making all connections and making good the disturbed surfaces in cement mortar (1:3) to match with the existing surface, complete all as specified and directed. |
| 33 | Supply and fixing in repair of vitreous china squatting pan of orrisa pattern size 580 x 440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and foot rests of anypattern complete including provision of lime concrete bed and connection to flush pipe excluding flushing cistern, flush pipe and bracket and making good the disturbed area complete all as specified and directed. |
| 34 | Material and labour for taking down shutter of any description not exceeding 1.00 sqm and refixing in same opening after necessary repair/easing and adjusting complete all as specified and as directed. |
| 35 | Material and labour for taking down shutter of any description exceeding 1.00 sqm but not exceeding 2.0 each and refixing in same opening after necessary repair/easing and adjusting complete all as specified and as directed. |
| 36 | Supply and fixing of 18mm thick PVC sheet having one side decorative laminated sheet all required brackets SS screws etc. the panel shall be fabricated using adhesive and screws where ever required.all the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification including fitting i.e. magnetic catcher, stainless steel handleapproved including dismanteling existing board any type complete all as specified and directed.NOTE: - Material manufacture test certificate should be provided before execution of work. |
| 37 | Supply and fixing of lipping 1-1.5 mm thick 18 mm wide colour of approved design & color, fixed with solvent cement or head less nails to PVC door complete all as specified and directed |
| 38 | Supply and fixing of continous (Piano) type hinges mild steel bright finish or lectro galvanised with wide of flaps40mm complete all as specified and directed. |
| 39 | Supply and fixing of 100 mm size hasp and staple,safety type,Stainless steel bright finish, including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 40 | Supply and fixing of aluminium handle cast type anodized 125 mm long complete all as specified and directed. |
| 41 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 42 | Supply and fixing framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed. |
| 43 | Supply and fixing of 0.80 mm thick mild steel plain black sheeting as in covering to door shutters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc.as required complete all as specified and directed. |
| 44 | Material and labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 45 | Supply and fixing of 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor including dismantling existing pipe etc complete all as specified and directed. |
| 46 | Supply and fixing of 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor including dismantling existing pipe etc complete all as specified and directed. |
| 47 | Supply and fixing in repair of 75mm bore PVC (SWR) bends any radius including jointing with solvent cement complete all as specified and as directed. |
| 48 | Supply and fixing in repair of 75 mm bore PVC (SWR) junction single T (equal or unequal), including jointing with solvent cement, complete all as specified and directed. |
| 49 | Supply and fixing in repair of 75/100 mm dia CP grating any type fixed in floor and jointed in CM 1:3 complete all as specified and as directed. |
| 50 | Supply and fixing in repair of PVC (SWR) floor trap, plain with grating including jointing with solvent cement of outer dia metre outlet of 75 mm complete all as specified and directed. |
| 51 | Supply and fixing in repair of stop valves, 15 mm dia, chromium plated, fancy type, ISI marked,screwed down, high pressure with capstain head, (concealed type) with long shank, screwed both ends for iron pipes or for unions, complete all as specified and directed.(Note : Weight of stop valve shall not be less than 0.575 Kg) |
| 52 | Supply and fixing in repair of stop valve 15mm dia, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and as directed. |
| 53 | Supply and fixing in repair of 15 mm dia fancy type long neck, CP pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 54 | Supply and fixed in repairof CP bib tap screwed down high pressure, long body, cast copper alloy, chromium plated`with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified and directed. (Note : Weight of bib tap shall not be less than 0.575 Kg) |
| 55 | Supply and fixed in repair of CP bib tap cast copper alloy with flange, screwed down suitable for 15mm bore pipe or union, complete all as specified and directed.(Note : Weight of bib tap shall not be less than 0.575 Kg) |
| 56 | Supply and fixed in repair of door seal PVC 30mm wide with foam complete all as specified & directed. |
| 57 | Supply and fixing in repair of PVC connections 45 cm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified and as directed. |
| 58 | Supply and fixing in repair of CP brass tubular towel ring, 150 mm dia fixed with CP brass screws complete all as specified and as directed. |
| 59 | Supply and fixing in repair of flush pipes to pedestal pan, including all joints complete all as specified and as directed. |
| 60 | Supply and fixing in repair of PVC heavy duty Health faucetincluding 1.50 meter long flexible tube and hook complete all as specified and as directed. |
| 61 | Supply and fixing in repair of chromium plated towel rail 750 mm longcomplete all as specified and as directed. |
| 62 | Supply and fixing in repair of brass CP toilet paper holder, recessed type, fixed to wall with brass CP screws complete all as specified and as directed. |
| 63 | Supply and fixing in repair of soap dish chromium plated of size 100x100x60mm superior quality, fancy type fixed with and including brass CP screws complete all as specified and as directed. |
| 64 | Supply and fixing in repair of chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union with shower arm complete all as specified and as directed. |
| 65 | Supply and fixing in repair of pegs set of 6 Nos, power coated GIfixed with cadmium plated screws complete all as specified and as directed. |
| 66 | Supply andfixing in repair of stainless steel sink with drainage board 1.00 mm thick, ISI marked for kitchen with plug, washers and wastes, including bedding in cement mortar on to dwarf wall or fixing contilever brackets of suitable angle iron, CP brass waste coupling, superior quality PVC waste pipe and connecting union to pipe, over all size 915mm x460mm, bowl size 410mm x 330mm x160mm complete all as specified and directed. |
| 67 | Supply and fixing of GI tubing, ISI Marked, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing wherever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed. |
| 68 | Refixing old serviceable steel water tubing of 15 mm bore, in new or old position,any grade, including Supply and fixing new fittings as required, fixed to walls and ceilings or laying in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed. |
| 69 | Supply and fixing of chlorinated PVC (CPVC) pipes 20 mm outer dia, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.0 m spacing. includes jointing of pipes & fittings with one step CPVC solvent cement with testing of joints including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing wherever required, including taking down of old tubing as existing at site and removal, complete all as specified anddirected. |
| 70 | Taking down chowkats or frames with shutter, areanot exceeding 1.50 Square metre(w/o taking off shutters from frames) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfacesin CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.(Note – The qouted rate shall be deemed toinclude for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid). |
| 71 | Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with mild steel hold fast / lugs /SS dash fasteners of required dia and length complete all as specified and directed.Note :- (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made.(ii) Material manufacture test certificate should be provided before execution of work. |
| 72 | Supply and fixing of factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site with 03 Nos extruded aluminium alloy butt hinges 100mm, 02 Nos aluminium tower bolt 150 mm, 02 Nos aluminium handle 150 mm for each shutter all as per specification & drawing complete all as specified and directed |
| 73 | Material and labour forproviding and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete complete all as specified and directed. NOTES : - (i) The ATT work shall be carriedout through specialised agency as approved by GE in writing and chemical used shall be approved before execution of work. (ii) 5% amount of the total amount of ATT shall be retained as a guarantee and shall be released after 10 years. However contractor may deposit the FDR of same amount in favour of GE. If contractor fail to rectify the defect pointed out during this period in writing, the defect shall be got rectified at contractor\" risk and cost and the payment shall be made from the amount kept reserved or by encashing the FDR deposited by the contractor as guarantee. Contractor\"s quoted rate for this item shall deemed to be inclusive of this aspect. |
| 74 | NOTE:- Amount of credit ofRs. 25,205.00 for retrieved materials is mentioned in Schedule of Credit Page No 19 & 20 of tender documents in pdf form which will be deducted offline while acceptance of tender. |
