Tender For Construction Of Compound Wall Atmettur Main Road Ohtin Bhavani Municipality
Tender Value
4 Lakhs
Estimated cost
Bid Submission
19 Jul 2023
0 days left
EMD
4000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
bhavani → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Compound Wall Atmettur Main Road Ohtin Bhavani Municipality
BOQ
| Sl. No. | Item Description |
| 1 | Earth work excavating and depositing on bank with initial lead of 10m and lift of 2m for foundation in hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders including cost of refilling the sides of foundation etc., complete. SS 20B |
| 2 | Cement concrete 1:4:8 mix (One cement four sand and eight aggregate) using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges including mixing, laying consolidating andcuring etc., complete as per standard specification - 10m³ |
| 3 | Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. |
| 4 | Supplying and erecting, centering for sides and soffits including supports and strutting upto 3.29m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheet of 90cm x60cm BG 10 gauge stiffened with welded M.S. angle of 25 x 25 x 3mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10 cm to 13 cm dia spaced at not less than 75 cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specification.(The payment for centeringshall be made only after the concrete is laid. The retrieved materials should be taken back by the contractor) Plane surface such as RCC square or rectangular columns, top and bottom slab of sunshade, boxing sill slabs etc., |
| 5 | SupplyingandFabrication of Steel and placing in position MS / Ribbed tor steel Grills for RCC works as per design given including cost of steel and GI binding wire in Floors etc,. Complete complying with standard specification in force |
| 6 | RCC1:1½:3 (One cement one point five sand and three aggregates) mix using 20mm gauge hard granite broken stone jellyin all RCC works connected to the work excludingshuttering , Centering and cost of Reinforcement grills butincludingcuring ,finishingetc complete with standard specification. |
| 7 | Brick work in cement mortar 1:5 mix (one cement and five sand) using second class ground bricks of size 23cm x 11cm x 7cm including cost, conveyance of all materials at site and all labour charges and incidental charges etc., complete as per standard specification.. |
| 8 | Plastering with cement mortar 1:5 mix to 12mm thick including cost and conveyance of all materials to site and all labour charges etc complete. |
| 9 | Plastering in cement mortar 1:3 mix 10mm thick using clean screened sand and including cost of curing for fifteen days from the completion of thework and surface should free from undulationsand including the cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification. |
| 10 | Painting two coats with ready mixed water proofPlastic Emulsion paint of approved quality and colour over a priming coat, including Thorough scrapping, clean removal of dirt, etc., completed and including necessary plaster of paints of pairs, putty, wherever required. as per standard specification |
| 11 | Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed SC copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A FT switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light / fan point (for electronic regulator) (5 points per coil(SD 22) |
| 12 | Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade in suitable pipe on wall and ceiling with PVC accessories with 150mm x 100mm x 113mm TW switch box for 15A 3 pin non inter locking wall socket with 15A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC power plug point(SD39) |
| 13 | Wiring with 2 x 1.5 sq.mm (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x 100 x 113mm TW switch box for 5A 3 pin non inter locking Wall socket with 5A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point(SD36) |
| 14 | Supply and fixing of 1200mm (48\") AC ceiling fan complete with stepped electronic 300W regulator with 300mm down rod on the existing clamp(SD110) |
| 15 | Supply and fixing of trusses using necessary \"L\" angels and I section each according to design approved by the departmetal officers including cutting, welding cost and conveyance of all materials to site and all labor charges etc., complete as per standard specification |
| 16 | Supply and fixing of trusses using necessary \"L\" angels and I section each according to design approved by the departmetal officers including cutting, welding cost and conveyance of all materials to site and all labor charges etc., complete as per standard specification |
| 17 | Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers. |
AI Tender Summary
Tender Timeline
Jul 13, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedJul 19, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJul 19, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender