Military Engineer Services-MES has published Tender For Repair /Maintenance Of Dg Sets, Amf Panel And Pumping Sets, Connected Panels, Starter, Cleaning Of Oht And Connected Works At Af Stn Bkt. Submission Date for this Tender is 26-07-2023. Diesel Generators Tenders in Lucknow Uttar Pradesh. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 19-Jul-2023 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 26-07-2023 |
| Sl. No. | Item Description |
| 1 | M&L for servicing of existing make and model DG set of capacity 5 KVA to 15 KVA including lubrication check the coolent oil level, check fuel system functioning, tappet cover adjustment & gasket replacement, draining out the engine oil from sump exhaust system inspection and clean the surfaceincluding replacement of following spares complete all as specified and directed by Engineer-in-Charge. Note: Spares will be measured & paid separately under respective items here in after but fixing of the same deemed to be included in quoted Rates. |
| 2 | Supply only in replacement of Diesel fitter, against Item No 1 here-in-before. |
| 3 | Supply only in replacement of Lub oil filter,against Item No 1 here-in-before. |
| 4 | Supply only in replacement Air filter element,against Item No 1 here-in-before. |
| 5 | Supply only in replacement of Fan belt,against Item No 1 here-in-before. |
| 6 | Supply only in replacement flexible pipe set complete,against Item No 1 here-in-before. |
| 7 | Supply only in replacement Lub oil pipe,against Item No 1 here-in-before. |
| 8 | Supply only in replacement Radiator hose pipe set,against Item No 1 here-in-before. |
| 9 | Supply only in replacement LLOP Sensor,against Item No 1 here-in-before. |
| 10 | M&L for servicing of existing make and model DG set of capacity 30 KVA to 45 KVA including lubrication check the coolent oil level, check fuel system functioning , tappet cover adjustment & gasket replacement, draining out the engine oil from sumpexhaust system inspection and clean the surfaceincluding replacement of following spares complete all as specified and directed by Engineer-in-Charge. Note: Spares will be measured & paid separately under respective items here in after but fixing of the same deemed to be included in quoted Rates. |
| 11 | Supply only in replacement of Diesel fitter,against Item No 10 here-in-before. |
| 12 | Supply only in replacement of Lub oil filter,against Item No10 here-in-before. |
| 13 | Supply only in replacement Air filter element,against Item No 10 here-in-before. |
| 14 | Supply only in replacement of Carbon bush,against Item No 10 here-in-before. |
| 15 | Supply only in replacement of coupling Rubber type,against Item No 10 here-in-before. |
| 16 | Supply only in replacement of Fan belt,against Item No10 here-in-before. |
| 17 | Supply only in replacement high pressure Flexible pipe complete,against Item No10 here-in-before. |
| 18 | Supply only in replacement Lub oil pipe,against Item No 10 here-in-before. |
| 19 | Supply only in replacement Radiator hose pipe set,against Item No10 here-in-before. |
| 20 | Supply only in replacement LLOP Sensor,against Item No 10 here-in-before. |
| 21 | M&L for servicing of existing make and model DG set of capacity 50 KVA to 82.5 KVA including lubrication check the coolent oil level, check fuel system functioning, tappet cover adjustment & gasket replacement draining out the engine oil from sump exhaust system inspection and clean the surfaceincluding replacement of following spares complete all as specified and directed by Engineer-in-Charge. Note: Spares will be measured & paid separately under respective items here in after but fixing of the same deemed to be included in quoted Rates. |
| 22 | Supply only in replacement of Diesel fitter,against Item No 21 here-in-before. |
| 23 | Supply only in replacement of Lub oil filter,against Item No 21 here-in-before. |
| 24 | Supply only in replacement Air filter element,against Item No21 here-in-before. |
| 25 | Supply only in replacement of Carbon bush,against Item No 21 here-in-before. |
| 26 | Supply only in replacement of coupling spidertype,against Item No21 here-in-before. |
| 27 | Supply only in replacement of Fan belt,against Item No21 here-in-before. |
| 28 | Supply only in replacement high pressure Flexible pipe complete set ,against Item No 21 here-in-before. |
| 29 | Supply only in replacement Lub oil pipe,against Item No21 here-in-before. |
| 30 | Supply only in replacement Radiator hose pipe set,against Item No21 here-in-before. |
| 31 | Supply only in replacement LLOP Sensor,against Item No 21 here-in-before. |
| 32 | M&L for servicing of existing make and model DG set of capacity 100 KVA to 125 KVA including lubrication check the coolent oil level, check fuel system functioning, tappet cover adjustment & gasket replacement draining out the engine oil from sumpexhaust system inspection and clean the surfaceincluding replacement of following spares complete all as specified and directed by Engineer-in-Charge. Note: Spares will be measured & paid separately under respective items here in after but fixing of the same deemed to be included in quoted Rates. |
| 33 | Supply only in replacement of Diesel fitter,against Item No 32 here-in-before. |
| 34 | Supply only in replacement of Lub oil filter,against Item No 32 here-in-before. |
| 35 | Supply only in replacement Air filter element,against Item No 32 here-in-before. |
| 36 | Supply only in replacement of Carbon bush,against Item No 32 here-in-before. |
| 37 | Supply only in replacement of Fan belt,against Item No 32 here-in-before. |
| 38 | Supply only in replacement high pressure oil pipe,against Item No 32 here-in-before. |
| 39 | Supply only in replacement Lub oil pipe,against Item No 32 here-in-before. |
| 40 | Supply only in replacement Radiator hose pipe set,against Item No 32 here-in-before. |
| 41 | Supply only in replacement LLOP Sensor,against Item No 32 here-in-before. |
| 42 | M&L for servicing of existing make and model DG set of capacity 160 KVA to 250 KVA including lubrication check the coolent oil level, check fuel system functioning tappet cover adjustment & gasket replacement draining out the engine oil from sump exhaust system inspection and clean the surfaceincluding replacement of following spares complete all as specified and directed by Engineer-in-Charge. Note: Spares will be measured & paid separately under respective items here in after but fixing of the same deemed to be included in quoted Rates. |
| 43 | Supply only in replacement of Diesel fitter,against Item No 42here-in-before. |
| 44 | Supply only in replacement of Lub oil filter/super bipass oil filter, against Item No 42 here-in-before. |
| 45 | Supply only in replacement Air filter element,against Item No 42 here-in-before. |
| 46 | Supply only in replacement of coupling Spider type,against Item No 42 here-in-before. |
| 47 | Supply only in replacement of Fan belt,against Item No 42 here-in-before. |
| 48 | Supply only in replacement high pressure flexible pipe complete set,against Item No 42 here-in-before. |
| 49 | Supply only in replacement Lub oil pipe,against Item No 42 here-in-before. |
| 50 | Supply only in replacement Radiator hose pipe set,against Item No 42 here-in-before. |
| 51 | Supply only in replacement LLOP Sensor,against Item No 42 here-in-before. |
| 52 | M & L for filling/topping up new engine oil in DG sets installed at various locations at AF station BKT complete all as directed & approved by Engineer-in-charge. Make : Servo super 20W 40 of Indian Oil or Equivalent grade of Hindustan Petrolium. |
| 53 | M & L for topping up of water coolent in radiator of DG sets installed at variouslocations at AF station BKT complete all as directed & approved by Engineer-in-charge. Make : TVS Girling/volvo line or of equivalent make all as approved |
| 54 | M&L for filling / pouring distill water packed in 20 / 25/ 35 litre PVC containers & top up of electrolite for servicing of battery complete all as specified & directed . |
| 55 | M&L for replacement of unserviceable PCB digital controller of any make as existing on site for capacity of upto 250 KVA DG sets control Panel and supply and fixing newPCB digital controller of any make as existing on site and testing the functioning of digital controller on load for smooth functioning of DG set copmplete all as specified and directed by EIC. |
| 56 | M & L for dismantaling of FIP for ovarhaulling and caliberationincluding replacement of wornout rings plungers,damper plate, gaskit etc and reassembling testing complete for following DG sets. (a) 5 KVA to 15 KVA |
| 57 | (b) Ditto same as Item No 56 here-in-before but 30 KVA to 50 KVA |
| 58 | (c) Ditto same as Item No 56 here-in-before but 63 KVA to 125 KVA |
| 59 | (d) Ditto same as Item No 56 here-in-before but 160 KVA to 250 KVA |
| 60 | M&L for replacement of existing make and model Genset Controller unit complete set suitable for existing DG sets and AMF along with all necessary connections including taking down of existing complete all as directed by Engineer-in-Charge. |
| 61 | M & L for repair overhalling of self starter including replacement of worn out clutch assembly bush, spring, plunger assembly, solenoid switch, corbon brushs, spring etc for the following DG set. (a) 5 KVA to 30 KVA |
| 62 | (b) Ditto same as Item No 61 here-in-before but 50 KVA to 100 KVA |
| 63 | (c) Ditto same as Item No 61 here-in-before but 125 KVA to 250 KVA |
| 64 | Repair/overhaling of dynamo/charging alternator including replacement carbon, brushes holder, spring commutator/slipring assembly bearing regulator its of any make, type and capacity, complete all as specified and directed. |
| 65 | Cleaning of the fuel tank of DG sets of following capacity after decaning the diesel, after throughly cleaning with kerosene oil including replacement of level indicator pipe complete all as specified and directed by Engineer-in-Charge. (a) 5KVA to 45KVA |
| 66 | (b) Ditto same as Item No 65 here-in-before but 50 KVA to 125 KVA |
| 67 | (c) Ditto same as Item No 65 here-in-before but 160 KVA to 250 KVA |
| 68 | M & L for dismantling and removing of water pump assessmbly complete from the engine repair/overhaulling the same by replacing worn out components like bearing, impeller, bushes, oil seal, water seal, gaskit etc. reassembling, refixing and testing complete for the following. (a) 30KVA to 75 KVA DG set |
| 69 | (b) Ditto same as Item No 69 here-in-before but 82.5KVA to 250 KVA DG set |
| 70 | M & L for Automatic voltage regulator suitable for DG set of following rating complete all as directed & approved Make & model by Engineer-in-Chagre :- (a) 10 KVA to 45 KVA |
| 71 | Ditto same as Item No 70 here-in-before but 50 KVA to 100 KVA |
| 72 | Ditto same as Item No 70 here-in-before but 125 KVA to 160 KVA |
| 73 | Ditto same as Item No 70 here-in-before but 250 KVA |
| 74 | M&L for Preparing old painted steel and metal based surfaces such as engine,alternator,radiator,complete body of dg set etc of any shape, size and description, removing oil, dust & rust by using sand paper or any method on all types of surfaces, and applying one coat spray painting with synthetic enameled paint of existing color of approved quality with and including writingSM/MES Nos,complete all as specified and directed by Engineer-in-Charge |
| 75 | M & L for replacement of fuel shutdown valve assembly complete testing including replacement of old unsv valves of any capacity DG set, complete all as approved & directedby Engineer-in-Charge . |
| 76 | M & L for replacement of bendix drive pinon assembly of self starter of capacity 30 KVA to 250 KVA DG set complete all as specified & approved by Engineer-in-charge. |
| 77 | M & L for replacement of existing make and model fly wheel ring including heating for press fitting for engine of following DG setwith all T&P required complete all as specified & approved by Engineer-in-charge. (a) 30 KVA to 63 KVA |
| 78 | Ditto same as Item No 77 here-in-before but 75 to 250 KVA |
| 79 | M & L for replacement of stop solonoid 30KVA to 50 KVA DG Set complete all as specified & approved by Engineer-in-charge. |
| 80 | Ditto same as Item No 79 here-in-before but for 63 to 100 KVA |
| 81 | Ditto same as Item No 79 here-in-before but for 125 to 250 KVA |
| 82 | M&L for cleaning/servicing of radiator of DG set of capacity 15 to 50 KVA including replacement of gasket packing, nuts, bolts, washers (if required) and descaling with appropriate chemicaland brazing/welding/replacement of damazed fins/tubes (if required) and reassembling & refixing in same position after testing complete all as specified & directed . |
| 83 | Ditto same as Item No 82 here-in-before but of capacity 63 to 100 KVA |
| 84 | Ditto same as Item No 82 here-in-before but of capacity 125 to 250 KVA |
| 85 | M & L for replacement of moulded rectifier unit on existing make DG set of capacity 120 ohm for alternator excitor unit complete all as specified & directed . |
| 86 | Ditto same as Item No 104 here-in-before but of capacity 140 ohm |
| 87 | M & L for repairing of comlete GENSET engine wiring including extesion of existing PVC insulated , stranderd copper conductor wire of size 2.5 sq mm /1.5 sq mm for control/ signal circuit complete with & including copper lugs, PVC ties, fasteners & synchronisation and calliberation of AMF panel with engine control panel complete all as specified & directed . |
| 88 | Supply, lay, jointing and testing XLPE insulated LT under ground cable 95 Sqmm 3.5 core, 1100 volts grade heavy duty, armoured with multi stranded aluminium conductor laid in trenches/ ducts, in pipes, on wall or on poles etc complete all as specified and as directed. |
| 89 | M & L for replacement of matalic canopy hinge on existing make DG set / LT panel of different locations including necessary welding work if required complete all as specified & directed . |
| 90 | S&F Thermostatof existing make and model suitable for existing DG set complete all as specified and directed. |
| 91 | M&L for servicing / repairing of AMF panel of DG sets of various capacityinstalled at AFS BKT Area by cleaning the complete panel with suitable cleaning agent and checking the controller relays, timer, contactors forproper functioning, replacement of defective wires,diodes resistor of existing make and size (if required), tightening of all connections complete all as specified and directed by Engineer-in-Charge. |
| 92 | M & L for SMPS based Electronic Battery Charger suitable for 12 / 24 Volts battery charging systemincluding connecting copper wire complete all as specified & approved by Engineer-in-charge. |
| 93 | M & L for replacement of spare coil for contactor of any capacity & type complete all as specified and approved by Engineer-in-charge. Make:- L&T/Schneider /Siemens. |
| 94 | M & L for replacement of contactor 4 pole, 360/400 Amp, 415 Volt of existing make and model complete all as specified and approved by Engineer-in-charge. |
| 95 | M & L for replacement of contactor 4 pole, 200/255 Amp, 415 Volt of existing make and model complete all as specified and approved by Engineer-in-charge. |
| 96 | M & L for replacement of contactor 4 pole, 130/160 Amp, 415 Volt of existing make and model complete all as specified and approved by Engineer-in-charge. |
| 97 | M & L for replacement of contactor 4 pole, 80/100 Amp, 415 Volt of existing make and model complete all as specified and approved by Engineer-in-charge. |
| 98 | M & L for replacement of contactor 4 pole, 50/63 Amp, 415 Volt of existing make and model complete all as specified and approved by Engineer-in-charge. |
| 99 | M & L for replacement of engine start relay 12/24 Volts of existing make and model complete all as specified and approved by Engineer-in-charge. |
| 100 | M & L for replacement of over and under voltage relay 3 phase 415 Volts of existing make and model complete all as specified and approved by Engineer-in-charge. |
| 101 | M & L for replacement of Auxiliary relay 8 pin /11 pin complete of existing make and model complete all as specified and approved by Engineer-in-charge. |
| 102 | M & L for replacement of timer switch AC/DC of existing make and model complete all as specified and approved by Engineer-in-charge. |
| 103 | M & L for replacement of Auto / Manual switch complete assembly of existing make and model complete all as specified and approved by Engineer-in-charge. |
| 104 | M & L for replacement of Indicaton lamp of existing make and model complete all as specified and approved by Engineer-in-charge. |
| 105 | M & L for replacement of Volt /Amp meter of existing make and model complete all as specified and approved by Engineer-in-charge. |
| 106 | Dismantling the defective alternator from DG set, transporting to work shop, separating the stator and rotor from alternator housing, cutting and removing burnt winding of stator/rotor completely, cleaning the slots and rewinding the stator and rotor with existing gauge of super enameled copper wire with suitable insulation, applying varnish and heating in heating chamber till completely dried and reassembling the alternator, transporting back to site and re-fixing to the DG set including proper alignment for smooth running and testing on completion for DG set of capacity upto 250 KVA complete all as specified and directed by Engineer-in-Charge. |
| 107 | Dismantling and top overhaulling of DG set of capacity upto 250 KVA of existing make including replacement of following unserviceable spare parts and reassembling the same its original location and testing complete all as specified and directed. Note: Spares will be measured & paid saperatly under respective items here in after but fixing of the same deemed to be included in quoted Rates. |
| 108 | Supply only Piston assy complete,against Item No 107 here-in-before. |
| 109 | Supply only Piston ring set,against Item No 107 here-in-before. |
| 110 | Supply only Liner set,against Item No 107 here-in-before. |
| 111 | Supply only C R bearing,against Item No 107 here-in-before. |
| 112 | Supply only tharmostat ,against Item No 107 here-in-before. |
| 113 | Supply only C R bush,against Item No 107 here-in-before. |
| 114 | Supply only inlet Valve set,against Item No 107 here-in-before. |
| 115 | Supply only exhaust Valve set,against Item No 107 here-in-before. |
| 116 | Supply only Valve guide with sheet,against Item No 107 here-in-before. |
| 117 | Supply only Cylinder head gaskit,against Item No 107 here-in-before. |
| 118 | Supply only Set of O ring,against Item No 107 here-in-before. |
| 119 | Supply only paking kit,against Item No 107 here-in-before. |
| 120 | Supply only oil seal front against Item No 107 here-in-before. |
| 121 | Supply only oil seal rear against Item No 107 here-in-before. |
| 122 | M & L for Earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in theground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron strip 32 x 6 mm as earth leadby means of bolts, nuts and washers of GIup to test point, GI tubing 40 mm bore medium grade protection pipe, GI watering pipe 20mm bore medium grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC M-25 cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-1 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. Notes: 1.Earth lead & protection pipes length upto & including 7.50 metre shall be deemed to be inclusive in the quoted rate. 2.On testing,after completion of job ,if desired earth resistence is not found ,the earthing shall be redone at no extra cost to govt. |
| 123 | M & L for replacement of off load change over switch 4 Pole, 415 Volt, capacity 200 Ampscomplete all as specified & approved by Engineer-in-charge. Make-L&T/Schneider |
| 124 | M&L and T&P for daily/ routine maintenance of DG sets installed at variour location of AF STN BKT for its smooth fonctioning including noting of faults or defects in engine/alternator/panel (if any) and rectify minor defects like air in fuel system, tightening of nut, bolts, wires, battery lead etc and also checking of lub oil, fuels, water level, switching ON/OFF system and all other fucntions and maintain the daily inspection register of DG sets as format provided complete all as specified & directed. Note:(i)Eahc day of 8 hrs shall be treated as each job. (ii) Spares /components if required shall be measured & paid separately under relevent items. (iii) The contractor has to engage minimum on skilled mechanic for carriying out this job. (iv) The tradesman shall report to concerned JE at 0900 AM daily. (v) If tradesmen found absent recovery at double the quoted rate will be effected from the bills. |
| 125 | Supply and installation of maintenance free battery lead acid type of capacity 12 Volt 180 AHforDG Setsinstalled at various locations Complete all as specified & approved by Engineer-in-charge. (Make Excide express/ Amron/ Microtek) |
| 126 | Ditto same as Item No 125here-in-before but capacity 12 Volt 150 AH. |
| 127 | Ditto same as Item No 125 here-in-before but capacity 12 Volt 120/130AH. |
| 128 | Ditto same as Item No 125 here-in-before but capacity 12 Volt 88/90 AH. |
| 129 | M & L for replacement of battery terminals brass with steel nuts, bolts & washers and complete all as specified & approved by Engineer-in-charge. |
| 130 | S & F battery lead wire 25 sqmm sizeflexible copper conductor single core (minimum 1.5 m length or as required at site) ,along with copper lug including taking out old unserviceable battery lead wire complete all as specified and directed. |
| 131 | Supply and fix RPM Meter with cable suitable for DG Set of various capacity including taking down of existing unserviceable meter complete all as specified and directed by Engineer-in-Charge. |
| 132 | Supply and fix Oil Pressure Gauge suitable for DG Set of various capacityincluding taking down existing unserviceable gauge complete all as specified and directed by Engineer-in-Charge. |
| 133 | Supply and fix Water Temperature Gauge suitable for DG Set of various capacityincluding taking down existing unserviceable gauge complete all as specified and directed by Engineer-in-Charge. |
| 134 | S&F Electric shock and treatment chart (Language: English-Hindi Combined) on acrylic sheet of size 50 cm x 70 cm duly marked permanent marking including 12mm thick plywood frame, clamps for fixing on wall etc all as specified and directed. |
| 135 | Supply & install Emergency First Aid Kit Box, Wall mounted , made from high grade GI metal with powder coating for anti rust proof,size 36 cm x 26 cm x 13 cm,color red &white,front toughened glass fitted , Multicompartment 4-shelf with security lock on door for safety including basic necessary medicinesfor First aid as directed by EIC complete all as specified and directed. |
| 136 | S&F Dos and Donts chart (Language: English-Hindi Combined)as per sample provided on acrylic sheet of size 50 cm x 70 cm duly marked permanent marking including 12mm thick plywood frame, clamps for fixing on wall etc all as specified and directed. |
| 137 | Dismantling of submersible pump and motor 1 HP to 3 HPfrom various location in (AF)Stn BKT , dismantling and carrying out necessary repairs to pump and motor, reassembling after replacement of following items & jobsand transporting back to siteand testing to entire satisfaction of EIC. Note:- (i) Spare parts required will be measured & paid separately here in after (ii) Tranportation of pump & motor to workshop (if requred) deemed to be included in quoted rate. |
| 138 | Supply only for replacement against item No 137 here in before Bushes,lock, key, bowel etc. |
| 139 | Supply only for replacement against item No137here in before Impeller |
| 140 | Supply only for replacement against item No 137 here in beforeThurst bearing plate |
| 141 | Supply only for replacement against item No 137 here in before Sand guard |
| 142 | Supply only for replacement against item No 137 here in before Submersible cable 2.5 sqmm 3 core copper conductor with suitable clips (make:-Finolex/ polycab). |
| 143 | Supply only for replacement against item No 137 here in before Refilling / remetalling of motor shaft , turning to bring itin original size,shape and polishing of submersible shaft of to match the existingsize. |
| 144 | Supply only for replacement against item No 137 here in before Bushes of submersible motor as per manufracture"s design and specification. |
| 145 | Supply only for replacement against item No 137 here in before Cutting outthe existing winding from stator of submersible motor rewinding of submersible motorwith exisitng sizeof copper wire. |
| 146 | Transportationof submersible pump and motor of cap 15 to 30HP 3 Phase from pump house at any location , dismantling for carrying out necessary repairs to motor or pump, transporting it back to site/store yard and testingafter replacement of following items & jobs to the entire satisfaction of EIC. (Note:- Spare parts required will be measured & paid separately here in after) |
| 147 | Labour only Cutting out the existing winding of stator/rotor of submersible motor of 15 to 30 HP,three phase and rewinding with PVC copper wire of existing size completeincluding insulating material etc all as specified and directed by Engineer-in-Charge. |
| 148 | Supply only for replacement against item No 146 here in before Thurst bearing block complete of submersible motor of any make. |
| 149 | Supply only for replacement against item No146 here in before Straightening of the slot of submerssible motor. |
| 150 | Supply only for replacement against item No 146 here in beforeBushes of submersible motor as per manufracture"s design and specification. |
| 151 | Supply only for replacement against item No 146 here in before Submersible cable 3 core of 6 sqmm size with suitable clips.Make:- Finolex/Polycab) |
| 152 | Supply only for replacement against item No 146 here in before Sand guard of submersible motor |
| 153 | Supply only for replacement against item No 146 here in before Sleeves in end plates |
| 154 | Supply only for replacement against item No 146 here in before Cable grommet. |
| 155 | Supply only for replacement against item No 146 here in before Water seal. |
| 156 | Supply only for replacement against item No 146 here in before Studs with nuts. |
| 157 | Supply only for replacement against item No146 here in before Remetaling of motor shaft,turning to bring it to original size and shape and polishing for submersible motor . |
| 158 | Supply only for replacement against item No 146 here in before Coupling of submersiable motor and pump with key. |
| 159 | Supply only for replacement against item No146here in before Complete overhauling of submersiable pump and replacement of the following spares:- |
| 160 | Supply only for replacement against item No 146 here in before Bowel bushes |
| 161 | Supply only for replacement against item No 146 here in before Neck ring |
| 162 | Supply only for replacement against item No 146 here in before Distant pieces |
| 163 | Supply only for replacement against item No146 here in before Steel impeller |
| 164 | Supply only for replacement against item No 146 here in before Bowel |
| 165 | Supply only for replacement against item No 146 here in before NRV |
| 166 | Supply only for replacement against item No 146 here in before Pump shaft |
| 167 | Supply only for replacement against item No 146 here in before Inlet body |
| 168 | Supply only for replacement against item No 146 here in before Slot wedges |
| 169 | Supply only for replacement against item No 146 here in before Cable jointing by using puncture compound roll and tape/ sealing compound complete. |
| 170 | Supply only for replacement against item No 146 here in beforePainting of submerssiblepump set. |
| 171 | M & L for taking out / lifting from bore wellsubmersible pump set of 15 to 30 HP capacityfrom bore well including columnpipeand connection cable, fitting through providing tripod assembly with chain pully in different locations of bore welland dismantling of cable, pumpset etc complete all as directed. |
| 172 | M & L for lowering of Pumpsetany size of capacity 15 to 30 HP withcolumn pipe includingreplacement of rubber packing andjointing cable & lowering and testing of Pump set for satisfactory run complete all as directed withcolumn pipe. |
| 173 | M & L for taking out submersible pump set of 1 HP to 3 HP capacityfrom bore well including columnpipeand connection cable, fitting through providing tripod assembly with chain pully in different locations of bore welland dismantling of cable, pumpset etc complete all as directed. |
| 174 | M & L for lowering of Pumpsetany size of capacity 1 HP to 3 HP with existing column pipe includingjointing cable & lowering and testing of Pump set for satisfactory run complete all as directed withcolumn pipe. |
| 175 | M & L for replacement ofsubmersible cable PVC insulated, overall PVC sheathed ,flat 10 Sqmm 3 core with copper conductor multistranded . Make-Finolex/Plaza/CCI/Havells/Polycap. |
| 176 | S&F in repairs PVC insulatedcopper conductor multistand submersible flat cable4 sqmm cross sectional area, 3 core including jointing and testing complete all as specified. Make - Finolex/Plaza/CCI/Havells/Polycap. |
| 177 | Supply and fixing (in repair)DOL starter complete fitted with Voltmeter and Ampearmeter suitable for 1 HP single phasesumbersibale pump set. Make C&S/Crompton/Kirloskar |
| 178 | Supply and fixing (in repair)Electronic Fully Automatic star delta starter three phase, 415 volts complete with Voltmeter, Ampermeter, single phase preventer and MCB etc suitable for 25-30 HP three phase submersible pump set Make: C&S/Crompton/Kirloskar/L&T |
| 179 | Supply onlyhigh strength Calcium based granular disinfection chemical(Chlorine containt not less 60%) containing corrosion inhibitors & anti scalants (CIAS) for water treatment all as specified. |
| 180 | Supply only TCC-90 complete all as approved & directed by Engineer-in- Charge |
| 181 | M & L for replacement ofsluice valveof dia 150 mm bore (ISI marked)PN 1.6 with new for distribution, rising main, wash out purpose to fix in pipe line complete with nut bolts, washers and rubber packing etc all as specified and directed. Make- Kartar, Zoloto, BIR |
| 182 | -ditto- same as per item No. 45above but 100 mm bore |
| 183 | M&L to repair of pressure pump/ booster pump set Electric driven of capacity 1 HP single phase 230Volts,50Hz AC complete including replacement of us connecting accessories and valves etc complete all as specified & directed. |
| 184 | M&L to repair of monoblock pump set of capacity 1 HP to 5 HP including replacement of unserviceable parts and testing on completion as directed by EIC. |
| 185 | Supply & testing with orthodine solution (in 500 ml pack), complete all as approved & directed by Engineer-in-Charge. |
| 186 | M & L for Transporting of centrifugal pumpset of capacity10 HP from AF Stn BKT, dismantling and carrying out following repairs to pump and motor,reassembling after replacement of following items & jobsand transporting back to site/store yard and testing to entire satisfaction of EIC. |
| 187 | M & L for Cutting and taking out burnt winding of motor of 10 HP capacity and rewinding with same size of copper wire as per existing quantity including insulating materials and making connection allas directed. |
| 188 | Supply only for replacement against item No 186 here in before Bearing front/rear |
| 189 | Supply only for replacement against item No 186 here in before Cover sleeve |
| 190 | Supply only for replacement against item No 186 here in before Pump reparing and overhauling |
| 191 | Supply only for replacement against item No 186 here in before Gland and packing of 10 HP pump set complete. |
| 192 | M&L to complete repair suction sweeper assembly complete with pumping set 2 HPand spring loaded nylon brush including replacement of unserviceable parts and testing including repair/replacement of MS angle and wheels and painting complete all as directed by EIC. |
| 193 | M&L for cleaning of RCC over head tanks single compartment (installed on stagging)comprising of the following operations :- (a) Dewatering of the tank shall be carried with gravitational flow. (b) Removal of left over dirty water and sludge with suitable sludge removal pump. (c) Cleaning of internal walls, floor, ceiling of tank shall be carried outand ensure that no dirt, algae or mass remain on surface of tank. (d) Remaining sludge shall be removed from the floor completely. (e) Tank shall be sterilized by spraying anti bacterial agent . (f) Date of cleaning and capacity of tank will be written on OHT with synthetic enamal paint. Cleaning will be done for following capacity RCC overhead tanks:- For 50,000 gallon Overhead tank |
| 194 | For 22,000 gallon Overhead tank |
| 195 | For 10,000 gallon Overhead tank |
| 196 | For 5,000 gallon Overhead tank |
| 197 | M&Lfor scraping old paint on CI/DI/GI pipe and sluice valve fitted to OH reservour having staging upto 16 m for supply, distribution, washout, rising, washout etc with two coats of synthetic enemel paint over a coat of red oxide primer as per color code provided by department, including marking arrow as directed in white color all as specified and directed for 150 mm dia CI/DI/GI pipe |
| 198 | All as per items No 197 but for 100/80 mm dia CI/DI/GI pipe |
| 199 | All as per items No 197 but for Sluice valve 150 mm |
| 200 | All as per items No 197 but for Sluice valve 100/80 |
| 201 | S&F Vacuum Hose pipe 40-50mm dia made of PVC heavy duty, floatinggreen ribbed colourcomplete all as specified. |
| 202 | S&F deep leaf netalong with 4.8 mtr telescopic pole for swimming pool and18" wall cleaning brush nylone/standard curved compelete all as specified and directed. |
| 203 | S&F PVC fibre rope standed type , 25 mm dia for suction sweeper pump complete all as specified. |
| 204 | Supply & lowering 100 mm dia heavy grade MS pipe flange typeincluding all fittings and fixtures along with lifting of old unserviceable complete all as specified & directed. |
| 205 | Supply & lowering High density polyethylene (HDPE) rigit pipes of pressure rating 6 kgf/sq. cm ,32 mm dia including all fittings and fixturesalong with lifting of old unserviceable complete all as specified & directed. |
| 206 | M&L for nut, bolt with washer of different sizes complete all as specified & directed. |
| 207 | M&L for contactor of starter panel sutable for 25-30 HP submersible pumping set, 415 volts of existing make and model including necessary electrical connection complete all as specified & directed. |
| 208 | Supply only Alumsuperior quality white colours complete all as specified and directed. |
| 209 | Supply only copper sulphate superior quality all as specified and directed. |
| 210 | S&F Heavy duty PVC coated stainless steel wire of size 4 mm diasuitable for holding the submersible motor of capacity upto 3 HP complete all as specified and directed. |
| 211 | Supply,Installation,Commissioning & testing submersible pump set Electric driven of capacity 2 HP single phase 230Volts,50Hz AC supply suitable for discharge of not less than 50 litre per minute (LPM) at 70m head having 40 mm delivery size directly coupled including PVC insulated,PVC sheathed,submersible cable 4sqmm 3 core copper conductor flat 1100 Volt grade of adequate lenght with necessary fixing arrangement and foundation etc. complete all as specified & directed. .Make :- Kirloskar/ CG/KSB |
| 212 | M & L for gland filling of Sluice Valves/Pumpscomplete all as directed and specified by EIC |
| 213 | Supply only H2SO4 acid in sealed container for cleaning of swimming pool basement. |
| 214 | M & L for checking of minor repair, leakage of decrin dozer fortnightly oras and when required loacted at different location of pump house 8,9,10,11, 7 and 358 TRU located in AF Stn BKT ofany capacity & make and testing complete to deliver recommended qty of chlorination. |
| 215 | M&L for taking down unserviceable pump tube of decrin dozer installed at various pump houses at BKT and replacing with new pump tube of existing make and model complete all as directed. |
| 216 | Ditto all as item No 216 above butInjection check valve 3/8"of existing make and model complete all as directed. |
| 217 | Ditto all as item No 216 above but Suction/discharge tube of size 3/8"of existing make and model complete all as directed.. |
| 218 | Ditto all as item No 216 above butWeighted suction line strainerof size 3/8"of existing make and model complete all as directed. |
| 219 | Ditto all as item No 216 above but Repairing and rewinding of Strainer motor complete |
| 220 | Ditto all as item No 216 above but Shaft with Impeller for strainer motorof existing make and model complete all as directed. |
| 221 | Ditto all as item No 216 above but Rollar assemblyof existing make and model complete all as directed. |
| 222 | Chemical and bacteriological testing of water sample from approved laboratory to ensure portability of water completeall as directed. Note: 1. Water sample will be collected in sealed container from pump houses and various locations at AF Stn BKT directed by Engr-in-Charge. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
