|
| 1 | Design, Supply and Double chamber Cremation Furnace LPG Burner fitting in Alternation work.Erection commissioning of LPG Burner System for Requirement of Cremation Furnaceof having 6 No’s Burners (Both side – Each 3) of rating 6 to 7.5kg/hrs and also necessary pipe lines, controls, Manifold, regulators and etc., |
| 2 | Dismantling and replacement of Gas Cleaning System (GCS) shall have ash Extractor before the Furnace for the removal ash from the producer Gas and shall have Venture Scrubbing arrangement after the Furnace capable of removing fine dust particulars throw wet washing the venture scrubber shall be connected to a wash column for Gaswater separation wash column shall be MS of 4mm thick plate suitably Manufactured. |
| 3 | Dismantling and Replacement of Supply & Construction of High Alumina (60%) Standard Bricks (9”x4”x3”), Cost-iron Body Bricks, Fire clay and Super refractory castable instulationwork. |
| 4 | Furnace Manual Operating Door Main soft Bearing with cover Block, Handle Soft with Bearing & 20mm Chain with Spracket wheel fully change and Servicework. |
| 5 | Centrifugal pump of suitable MoC to circulate to Mild Alkaline water through the Venturi scrubber at a rate of not less than 2 Lit/s with a Discharge pressure Head of 3Kg.cm2(min) in the Venturi and SuitablePlumbing work. |
| 6 | Dismantling and replacement of Double Chamber Cremation Furnace to Venturi Scrubber, Venturi Scrubber to centrifugal fan (5HP), Centrifugal fan to Chimney connection Suitable Pipe line work. |
| 7 | Dismantling and replacement of 100feet Chimney Top 40 feet Pipe Change work (60\" to 100\") with Painting Work |
| 8 | Dismantling & Supply of Centrifugal fans (5HP) of suitable rating for Furnace smoke collect and through to the Chimney Operation System |
| 9 | Cost for Overall service & Machinery painting work & Electrical Panel Board. |
| 10 | Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 11 | Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. |
| 12 | Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc, complete as per technical specification and as directed by the departmental officers. Morth - Rev V No. 111,112,401,900 |
| 13 | Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification |
| 14 | Plain Cement Concrete 1:2:4 (one cement, two fine aggregates and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour chargesetc., complete as per standard specification |
| 15 | Laying the Flooring withAnti skid coloured ceramic tiles of sizes 200mm X200mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:3 (one cement ,three sand) over 10 mm base layer plastering and pointing with white cement neatly as directed. |
| 16 | Dadooing walls withGlazed tiles of sizes 305mm X200mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed. |
| 17 | Paving the floor with design Rajasthankotta tiles (colour and shade as directed) of size 610 mm x 610mm x 20mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc, complete as per standard specification |
| 18 | Wiring with 2 x 1.5 sqmm (22/0.3) PVC insulatedunshealhed SC.Cu.conductor of1100V grade in suitable PVC rigid Pipe on wall and ceiling with PVC accessorieswith TW switch box with 5A F.T. switch inflush with wall, coveredwith hylum sheet of 3mm thick with painting of suitable colour for open PVClight/fan point(For Electronic regulator) (5 pointsper coil). SD 22 |
| 19 | Wiring with 2 x 1.5 sqmm (22/0.3) PVC insulated single core unshealhed copper conductor cable of 1100V grade in suitable heavygauge MS conduit pipeonwall and ceiling with M.S. accessories inflush with wall with 150mm x 100 mm x 75mm MS switchbox with 3mm thick hylum sheet cover for 5A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed plug point. SD 12 |
| 20 | Supply and fixing of single box type 4feet 36 W flu fitting complete with electronic ballast with TW round blockson wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting. SD 87 |
| 21 | Supply and fixing of 1200 mm (48\") sweep AC ceiling fan complete with stepped electronic 300W regulator, with 1 metre down rod with fan clamp with side plates and cross arm of size 450 mm (18\") SD-106 |
| 22 | Providing Entrance Name board using I angle frames and support post with finishing Aluminum composite panel base plate and snickering letter cutting and fixing all in night vision flickering types including cost of allmaterials and including all labour charges etc complete |
| 23 | Supply, Delivery and Providing Three Seater back slope Granite stiff sitting benches 5 feet in length 1.50 feet width 600x450x100 mm size Hard Granite slab side walls, 150x45x100 mm size bench slab back slope slab including cost and conveyance and fixing in position etc complete |
| 24 | Supply and Fixing of 48 W LED Street Light Outdoor Fittings as per PWD SOR P.No122 |
| 25 | Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade in suitable pipe on wall and ceiling with PVC accessories with 150mm x 100mm x 113mm TW switch box for 15A 3 pin non inter locking wall socket with 15A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC power plug point. SD -39 |
| 26 | GST18% |
