|
| 1 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface.(15mm thick in yellow colour)Transverse Bar Marking with stricter compliance as per IRC:99-2018Providing and laying of hot applied thermoplastic compound 15 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 15 mm is exclusive of surface applied glass beads as per IRC:35 upto date (Thermoplastic marking of 300mm wide and 15mm height, at 1000mm apart (one set is of 6 strips). 15mm height is achieved through six application of thermoplastic, applied at an interval not less than 1 hour after previous layer gets solidified. Alternatively, made of Mastic Asphalt or any equivalent material which would provide 15mm high). The finished surface to be level, uniform and free from streaks and holes. Material shall be tree from all skins, dirt and foreign objects and shall comply with requirements as per Table 800-9 of (MORTH SPECIFICATION) Thermoplastic Material when tested in accordance with ASTM D36/BS-3262-(Part 1) daylight Luminance shall beAASHTO M 249 for white 45o-65% min. and for yellow 45% min. , Drying time not more than 15 minutes, skin resistance not less than 45 as per BS-6044, material shall show no cracks on application to concrete blocks at Low Temperature, softening point 102.5oC ± 9.5oC as per ASTM D36 and yellowness index for white thermoplastic paint not more than 0.12 as per AASHTO M 249. Container of the thermoplastic material shall be clearly and indelibly marked with Name, Trade mark or other means of indentification of manufacturer, Batch No., Date of manufacturer, Colour, Maximum application temperature and maximum safe heating temperature. Glass beads shall meet the gradation requirement as per Table 800-10 of MORTH SPECIFICATION. The Glass beads shall have a minimum Reflective Index of 1.5 and 70% Roundeness. The Pavement Temperature shall not be less than 10oC during application of Hot thermoplastic paint. The Contractor shall furnish to the Engineer a copy of certified test reports from the manufacturer of the thermoplastic material/glass beads showing results of all test specified in MORTH SPECIFICATION and shall certify that the material meet all requirement of specification. |
| 2 | Supply & fixing of Bollard made(Single Side) out of 2mm thick aluminium sheet face to be covered with high intensity prismatic grade type IV sheeting , Legends , letters , numerals and borders etc should be as per MoRTH specification No-801.3.7 .Welded poly shaped to make it monolithic pillar size 1200 mm high Bollard is having a frame 900x600 mm and 600 mm dia for fixation made out of 35 x 35 x 5 mm angle iron and from side is fully cover with PCC M-25 grade of concrete. (size of foundation 0.45x0.45x0.60m). as per SOR Ch-26 SI No.-14 |
| 3 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67 upto date made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with PCC M-25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory/ Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer / Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67 upto date. Legends , letters , numerals and borders etc should be as per MoRTH specification No-801.3.7 . Proof of the same in form of government report shall be uploaded while quoting tender. As per SOR ch-26 SI no.-18Hazard Marker (30 x 90cm Left/Riight) Object Hazard |
| 4 | Speed Limit sign 30kmph on side lane (Backing Board) (80cm x 60 cm rectangular with diffinitation plate ( 20 x 60)) |
| 5 | Stop Sign(90cm high octagon |
| 6 | Speed Table Sign (60 cm equilateral triangle with diffinitation plate ( 20 x 60)) |
| 7 | Accidental zone(Crash Prone Area) (60 cm equilateral triangle with diffinitation plate ( 20 x 60)) |
| 8 | No Standing, No Stopping and No Parking |
| 9 | T-Intersection(60 cm equilateral triangle with diffinitation plate ( 20 x 60)) |
| 10 | T-Intersection major road ahead(60 cm equilateral triangle with diffinitation plate ( 20 x 60)) |
| 11 | Major road ahead (60 cm equilateral triangle with diffinitation plate ( 20 x 60)) |
| 12 | Providing and erecting direction and place identification retro-reflectorised sign as per IRC-67 upto date made of high intensity grade sheetingThe Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory/ Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer / Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67 upto date.Legends , letters , numerals and borders etc should be as per MoRTH specification No-801.3.7 . Sheet fixed over aluminium sheeting ,2 mm thick with area not exceeding 0.9 sqm.Supported on a mildsteel single angle iron post 75x75x6 mm firmly fixed to the ground by means of property designed foundation with PCC M-25 grade cement concrete 45x45x60cm, 60cm below ground level as per approved drawing, complete. as per SOR Ch-26 SI No.-19Crash Prone Area Black spot sign ( 900 x 600) |
| 13 | Providing and erecting direction and place identification retro-reflectorised sign as per IRC-67 upto date made of high intensity grade sheetingThe Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory/ Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer / Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67 upto date.Legends , letters , numerals and borders etc should be as per MoRTH specification No-801.3.7 . Sheet fixed over aluminium sheeting ,2 mm thick with area exceeding 0.9 sqm.Supported on a mildsteel double angle iron post 75x75x6 mm firmly fixed to the ground by means of property designed foundation with PCC M-25 grade cement concrete 45x45x60 cm,60cm below ground level as per approved drawing, complete.as per SOR Ch-26 SI No.-20Street Name Board |
| 14 | Supplying of Solar Raised Pavement Markers made polycarbonate molded body with circular shape , solar powered , LED self illumination in active mode , 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode . The marker shall support a load of 13635 kg tested in accordance to ASTM D 4280. The marker should be resistant to dust and water ingress according to IP 65 standards and should withstand temperatures in the range of 0 C to 70 C. Color of lighting could be provided in red or yellow ( amber ) as per requirement and typical frequency of blinking is 1 Hz . There should be current losses of less than 20 macroamperes at 2.4 V In sleepcharging mode to enhance the life of the marker and a full charge should provide for a minimum autonomy of 50 hours . The height , width and length of the marker shall not be less than 10 mm x 100 mm x 100 mm . Also , the surface diameter of the marker shall not be less than 100 mm respectively . The weight of the marker shall not exceed 0.5 kilograms . Fixing will be by drilling holes on the road for the shanks to go inside , without nails and using epoxy resin based adhesive and complete as directed by the engineer. as per SOR Ch-26 SI No.-16 |
| 15 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick in white colour including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 upto date The finished surface to be level, uniform and free from streaks and holes. Material shall be tree from all skins, dirt and foreign objects and shall comply with requirements as per Table 800-9 of (MORTH SPECIFICATION) Thermoplastic Material when tested in accordance with ASTM D36/BS-3262-(Part 1) daylight Luminance shall beAASHTO M 249 for white 45o-65% min. and for yellow 45% min. , Drying time not more than 15 minutes, skin resistance not less than 45 as per BS-6044, material shall show no cracks on application to concrete blocks at Low Temperature, softening point 102.5oC ± 9.5oC as per ASTM D36 and yellowness index for white thermoplastic paint not more than 0.12 as per AASHTO M 249. Container of the thermoplastic material shall be clearly and indelibly marked with Name, Trade mark or other means of indentification of manufacturer, Batch No., Date of manufacturer, Colour, Maximum application temperature and maximum safe heating temperature. Glass beads shall meet the gradation requirement as per Table 800-10 of MORTH SPECIFICATION. The Glass beads shall have a minimum Reflective Index of 1.5 and 70% Roundeness. The Pavement Temperature shall not be less than 10oC during application of Hot thermoplastic paint. The Contractor shall furnish to the Engineer a copy of certified test reports from the manufacturer of the thermoplastic material/glass beads showing results of all test specified in MORTH SPECIFICATION and shall certify that the material meet all requirement of specification. as Per SOR Ch-26 SI No.-2 |
