Dr. Yashwant Singh Parmar University of Horticulture has published Tender For Painting Outer Surface Of Non-Teachers Hostels At Dr. Ysp University Of Horticulture And Forestry Nauni- Solan. Submission Date for this Tender is 13-07-2023. Painting Tenders in solan Himachal Pradesh. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas on all depths and widths including getting out and disposal of all excavated earth in all leads, lifts and carriage of material as directed by the Engineer-in-Charge. a). Ordinary rock. |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level complete in all respect as per satisfaction of Engineer-in-Charge. |
| 3 | a). 1:5:10 (one Cement : five sand : ten graded stone aggregate 40 mm (fourty milimetre) nominal size |
| 4 | b) 1:3:6 (one Cement: three sand: six graded stone aggregate 20 mm (twenly milimetre) nominal size. |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form for etc. complete in all respect as per satisfaction of Engineer-in-charge. |
| 6 | a)Foundations, footings, bases of columns, etc. for mass concrete |
| 7 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws with 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size etc. complete in all respect as per satisfaction of Engineer-in-charge. a)Kiln seasoned and chemically treated hollock wood. |
| 8 | Providing and fixing fly proof galvanized MS wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm etc. complete in all respect as per satisfaction of Engineer-in-charge a). Second class teak wood beading 20 into 20 mm |
| 9 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202(PartI) non decorative type,coreof blockboard constructionwithframeof1st classhard wood andwell matched commercial3 ply veneering with vertical grains or cross bands andface veneers on both faces of shutters etc. complete in all respect as per satisfaction of Engineer-in-Charge.a). 35mmthickincludingISI marked Stainless Steel butt hinges with necessary screws |
| 10 | Providing and fixing 2nd class teak wood 40mm into 12 mm wooden Chamfered moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete in all respect as per satisfaction of Engineer-in-charge. |
| 11 | Providing and fixing ISI marked oxidized/ chromium plated M.S. single acting spring hinges with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.a)150 mm ( one hundred fifty milimetre) |
| 12 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). 250x16 mm |
| 13 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge. a).125mm |
| 14 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge. a) Fixing with adjustable lugs with split end tail to each jamb |
| 15 | 40 mm (forty milimetre) thick Cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm (twenty milimetre)nominal size finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete in all respect as per satisfaction of Engineer-in-Charge. |
| 16 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion etc. complete in all respect as per satisfaction of Engineer-in-Charge. (i) Single socketed pipesa). 110 mm(one hundred ten milimetre) diameter(Finolex/ D-Plast/ Vectus/ Kisan/ Prayag Make). |
| 17 | Providing and fixing on wall face unplasticised – PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion etc. complete in all respect as per satisfaction of Engineer-in-charge. |
| 18 | a) Coupler110 mm |
| 19 | b) 110 mm Shoe |
| 20 | Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement: 3 fine sand) etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Flush / Ruled/ Struck or weathered pointing |
| 21 | Applying priming coat With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) etc. complete in all respect as per satisfaction of Engineer-in-Charge. |
| 22 | Painting with synthetic enamel paint on steel/ wood of approved brand and manufacture to give an even shade etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Two or more coats on new work. |
| 23 | Finishing walls with Acrylic Smooth exterior paint of Required shade etc. in all respect as per satisfaction of Engineer-in-Charge. a). Old work (Two or more coatapplied @ 1.67 ltr/ 10 sqm) on existing cement paint surface |
| 24 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade etc. in all respect as per satisfaction of Engineer-in-Charge..a) Oneor more coats on old work |
| 25 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish tothedumping ground, all complete as per direction of Engineer-in-Charge. a).With cement mortar1:4 (one cement : four sand). |
| 26 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty etc. in all respect as per satisfaction of Engineer-in-Charge a).Floatglasspanes ofnominal thickness4 mm (weight not less than 10kg/sqm) |
| 27 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. |
| 28 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within all leads etc. complete as per direction of Engineer-in-charge. a). In cement mortar |
| 29 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 Sintex marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank etc. complete in all respect as per satisfaction of Engineer-in-charge. |
| 30 | Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
