Tender For Construction Of Kitchen And Dining Hall At Kasturba Gandhi Balika Vidyalaya, Dumri Block, District Gumla.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
08 Jul 2023
0 days left
EMD
50000
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
dumri → Jharkhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Kitchen And Dining Hall At Kasturba Gandhi Balika Vidyalaya, Dumri Block, District Gumla.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation in foundation trenches in hard soil (vide classification of soil item - A+B) and disposal of excavated earth as obtained to a distance up to 50M including all lifts with leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as perbuilding specification and direction of E/I.B.C.D. S.O.R. Item No. 5.1.1 + 5.1.2 |
| 2 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royaly and taxes all complete as per building specification and direction of E/l.B.C.D. S.O.R. Item No. 5.1.10 |
| 3 | Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I.B.C.D. S.O.R. Item No. 5.6.3 |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)B.C.D. S.O.R. Item No. 5.3.1.2 |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)B.C.D. S.O.R. Item No. 5.3.1.1 |
| 6 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)B.C.D. S.O.R. Item No. 5.3.10 |
| 7 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)B.C.D. S.O.R. Item No. 5.3.9.1 |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete.B.C.D. S.O.R. Item No. 5.3.17.1 |
| 9 | Providiag designation 75B brick work in Cement Mortar (1:6) in foudation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing taxes and royalty all complete job as per building specificition and direction of E/l.B.C.D. S.O.R. Item No. 5.2.6 |
| 10 | Providiag designation 75B brick work in Cement Mortar (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing taxes and royalty all complete job as per building specificition and direction of E/l.B.C.D. S.O.R. Item No. 5.2.14 |
| 11 | Reinforcedcementconcreteworkinbeams,suspendedfloors,roofshaving slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size).B.C.D. S.O.R. Item No. 5.3.11 |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts.B.C.D. S.O.R. Item No. 5.3.17.6 |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers.B.C.D. S.O.R. Item No. 5.3.17.5 |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc., including edges.B.C.D. S.O.R. Item No. 5.3.17.19 |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform.B.C.D. S.O.R. Item No. 5.3.17.3 |
| 16 | Providing 19mm water proof cement plaster (1:3) with clean coarse sand of F.M 1.5 with 5% cico or any other approved water proofing compound including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I.B.C.D. S.O.R. Item No. 5.7.15 |
| 17 | Providing and fixing fan hook of 16mm dia TMT M.S. bar 1 meter long bent to required size and shape placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/I.B.C.D. S.O.R. Item No. 5.5.13 |
| 18 | Supplying, Fitting and fixing M.S grill made of 20 x 6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, hoisting carriage of grill to work site hoisting as per building specification and direction of E/I.B.C.D. S.O.R. Item No. 5.5.12 |
| 19 | Supplying, fitting and fixing good quality, well dressed and well seasoned local wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.B.C.D. S.O.R. Item No. 5.4.3 |
| 20 | Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windowswith black board core blended with high qualityphenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.B.C.D. S.O.R. Item No. 5.4.38 |
| 21 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved mak+B50e conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) :For fixed Portion : Powder coated aluminium (minimum thickness of powder coating 50 micron)D.S.R. Item No. (a) 21.1.1.2 |
| 22 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) D.S.R. Item No. (b) 21.1.2.2 |
| 23 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) : With float glass panes of 5.0 mm thicknessD.S.R. Item No. 21.3.2 |
| 24 | Providing and laying Doublecharge vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) with water absorptionless than 0.08% and conforming to IS: 15622 / ISO 13006 of approvedmake, in all colours and shades, laid on 20mm thick cement mortar 1:4(1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching 600x600 mmB.C.D. S.O.R. Item No. 5.6.28 |
| 25 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.D.S.R. Item No. 8.31 |
| 26 | Providing 6mm cement plaster (1:4) in ceiling with clean coarse sand of F.M 1.5 including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I.B.C.D. S.O.R. Item No. 5.7.6 |
| 27 | Providing 12 mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes androyalty all complete as per specification and direcition of E/l.B.C.D. S.O.R. Item No. 5.7.3 |
| 28 | Earth filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and finally dressed with earth obtained from excavation of foundation trenches with a lead of 50m and lift of 1.5m all complete as per building specification and direction of E/l.B.C.D. S.O.R. Item No. 5.1.7 |
| 29 | Providing 12 mm thick cement plaster (1:4) with clean coarse sand of F.M. 1.5 with 1.5 mm cement punning including screening, curing with all leads and lifts of water, scaffolding, taxes androyalty all complete as per specification and direcition of E/l.B.C.D. S.O.R. Item No. 5.7.2 + 5.7.11 |
| 30 | Providing TMT steel reinforcement 8mm, 10mm, 12mm & 16mm dia bars as per approved design and drawing excluding carriage of M.S bar to work site, cutting, bending end binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.B.C.D. S.O.R. Item No. 5.5.4 : 8mm dia Bar - |
| 31 | B.C.D. S.O.R. Item No. 5.5.5 (a) : 10mm dia Bar - |
| 32 | B.C.D. S.O.R. Item No. 5.5.5 (b) : 12mm & above dia Bar - |
| 33 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.D.S.R. Item No. 13.80 |
| 34 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty where required, scaffolding, washing of floors and taxes all complete as per specification and direction of E/I.B.C.D. S.O.R. Item No. 5.8.18 |
| 35 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).D.S.R. Item No. 13.47.1 |
| 36 | Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.B.C.D. S.O.R. Item No. 5.8.32 |
| 37 | Providing two coat of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface throughly, scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.B.C.D. S.O.R. Item No. 5.8.43 |
| 38 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink asper IS:13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making goodthe walls wherever required : Kitchen sink without drain board, 610x510 mm bowl depth 200 mm.D.S.R. Item No. 17.10.2.1 |
| 39 | Supplying, fitting and fitting vitreous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed C.I. or M.S. brackets 32m C.I. brass waste, 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350 grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.D.W. & S. Item No. 3.2.5 |
| 40 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.D.S.R. Item No. 18.8 / 18.920mm dia |
| 41 | 32mm dia |
| 42 | Providing and fixing male ended bib cock of approved quality (wt. not less than 350 gms.) with extra socket all complete as per specification and direction of E/I.15mm dia Brass Bib CockD.W. & S. Item No. 3.1.5.1 |
| 43 | Providing and fixing brass/C.I. stop cock of approved quality as per specification and direction of E/I. Brass stop cock - 15mm diaD.W. & S. Item No. 3.1.6 |
| 44 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.D.S.R. Item No. 18.48 |
| 45 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) 110mm dia Single socketed pipes.D.S.R. Item No. 12.41.2 |
| 46 | Carriage of materials including loading, unloading, stacking -do- -do- all complete as per specification and direction of E/I.(i) Cement |
| 47 | (ii) Sand |
| 48 | (iii) Bricks |
| 49 | (iv) Steel |
| 50 | (v) Stone Chips |
| 51 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.Group B (Elec SOR 1.3.2) |
| 52 | Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.(Elec SOR 1.5) |
| 53 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.2 x 1.5 sq.mm + 1 x 1.5 sq.mm earth wire(Elec SOR 1.7.1) |
| 54 | 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire(Elec SOR 1.7.2) |
| 55 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). |
| 56 | Supplying and fixing of following sizes PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.(Elec.SOR-1.21)20 mm dia(Elec.SOR-1.21.1) |
| 57 | 25 mm dia(Elec.SOR-1.21.2) |
| 58 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.(Elec.SOR-1.24)5/6 amps switch(Elec.SOR-1.24.1) |
| 59 | 3 pin 5/6 amp socket outlet(Elec.SOR-1.24.4) |
| 60 | Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.(Elec.SOR-1.25) |
| 61 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.(Elec.SOR-1.26) |
| 62 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way, Double door(Elec.SOR-2.8.7) |
| 63 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"B\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.(Elec.SOR-2.11)Single pole(Elec.SOR-2.11.1) |
| 64 | Single pole and neutral (Elec.SOR-2.11.2) |
| 65 | Providing and fixing 1200mm Ceiling fan. (Elec.M-772) |
| 66 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable etc. as required.(Elec.SOR-1.44) |
| 67 | Providing and fixing 300mm Exhaust fan. (Elec.M-775) |
| 68 | Installation of exhaust fan (upto 450mm sweep) in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.(Elec.SOR-1.48) |
| 69 | Providing and fixing of LED Bulb - 9/10 watt(Elec.M-855) |
| 70 | Provision for Photograph & signboard |
| 71 | Add 18% GST= (+) |
| 72 | Add 1 % Labour cess=(+) |
AI Tender Summary
Tender Timeline
Jul 03, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedJul 08, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJul 11, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender