|
| 1 | EQUIPMENT LIST |
| 2 | Vernier Caliper Digital0-200 mm |
| 3 | External Micrometer (digital)Range0-25 mm |
| 4 | External Micrometer Range(Manual) 25-50 mm |
| 5 | Internal Micrometer Range(Digital) 25-50 mm |
| 6 | Dial Gauge (Metric System)with magnetic stand plunger type 0.01 mm ( Least Count) |
| 7 | Telescopic Gauge set of 60.313-6\" |
| 8 | Bore Gauge50-150 mm |
| 9 | Feeler Gauge Metric 25 blade |
| 10 | Straight Edge400 mm |
| 11 | Divider200 mm |
| 12 | Inside Caliper200 mm |
| 13 | Outside Caliper200 mm |
| 14 | Torque wrench set of 35-225 N-m |
| 15 | Digital Multi Meter0 to 1000 Ohms, 2.5 to 500 V |
| 16 | Hydrometer |
| 17 | Depth Gauge Range 0-50 mm |
| 18 | Bevel Gauge 12\" Blade, 5 minute Vernier Resolution |
| 19 | Battery Charger 6 Amp 12 Volt |
| 20 | Tyre pressure Gauge (Hand Held, Digital) 0-120 PSI |
| 21 | Hydrolic Jack (Trolley Type) 2 ton |
| 22 | Maintanance ToolsFasteners :-Bolts Gr 8, Gr 5, Gr 2 8, 10, 12, 14, 17 mm |
| 23 | NutsHex Nut , Castle Nut , Wing Nut , Locking Nut , Lug Nut , Speed Nut (Suitable size) |
| 24 | Studs-10 |
| 25 | ScrewsMachine Screws, Sheet Metal Screws(self tapping), Set Screw – (allen wrench/no head) |
| 26 | Washers Flat Washer, Lock Washer (Suitable size) |
| 27 | Roll-pins/Spring-pins |
| 28 | C - Clips Internal & External 10 each |
| 29 | General Purpose Tools Double Ended Spanner set6 x 7 mm 8 x 9 mm 10 x 11 mm 12 x 13 mm14 x 15 mm 16 x 17 mm18 x 19 mm20 x 22 mm |
| 30 | Ring Spanner Set6 x 7 mm 8 x 9 mm 10 x 11 mm 12 x 13 mm14 x 15 mm 16 x 17 mm18 x 19 mm20 x 22 mm |
| 31 | Socket Spanner set with20 sockets 10 mm onwardsT- Handle 12\"Extension Rod4\"Extension Rod8\"Ratchet Handle 12\"Rotating UnionUniversal Joint |
| 32 | Side Cutting Plier 200 mm |
| 33 | Round Nose Plier200 mm |
| 34 | Flat Nose Plier200 mm |
| 35 | Ball Peen Hammer with Handle500 grams |
| 36 | Cross Peen Hammer with Handle 200 grams |
| 37 | Screw Driver Straight tip 8\" Long |
| 38 | Screw Driver Straight tip 12\" Long |
| 39 | Phillips Screw Driver8\" Long |
| 40 | Phillips Screw Driver12\" Long |
| 41 | Hacksaw Frame fixed 300 mm |
| 42 | Hacksaw blades For above Hacksaw Frame |
| 43 | Cold Chisel Flat 10 mm |
| 44 | Allen Key set4 mm - 14mm |
| 45 | Oil Cane 500 ml |
| 46 | File flat bastard300 mm |
| 47 | File Square Rough300 mm |
| 48 | File flat smooth 2nd cut250 mm |
| 49 | File Rasp Cut300 mm |
| 50 | Emery Paper/Cloth 80 grit/ 120 grit/ 150 grit |
| 51 | Chassie Frame(LMV) (Old)Diesel With cross members. Mounted with engine, clutch, gear box, Rear axle, Front Axle, Propeller shaft and steering gear box with wheels, Motorized |
| 52 | Cut model of any engine(MPFI) Old, Motorized 4 cylinders, 1.2 L Cap, Power Approx. 80 kW, with electronic fuel pump, impeller type water pump, catridge type filters, Alternator, self Starter Compressor Thermostat |
| 53 | Live Axle Assly with Differential & Final Drive / Cut model of same, mounted on stand Differential( bevel geared, trunion, tail pinion, crown wheel) splined axle shaft, hub assly, opposed type taper roller bearing) |
| 54 | Dead Axle Assly with Stub Axle mounted on stand For light Motor Vehicle |
| 55 | Components of Suspension system Leaf spring Front & Rear,Centre bolt, Shackle bracket, Hanger bracket, U clamp, Shackle Pin |
| 56 | Cut model of Shock Absorber Telescopic Type |
| 57 | Components of steering System (at least each one) Mounted on stand Tie Rod, Rack & Pinion assembly, Complete all standard components. |
| 58 | Air Brake System with compressor Working model with all standard components |
| 59 | Mechanical brake assembly Pedal, Linkage, Cam & Brake shoe, mounted on a board |
| 60 | Hydraulic brake assembly Master cylinder, Servo(Vaccum/Pressure), Wheel cylinder, Pipe lines, mounted on a board |
| 61 | Components of Automobile Electrical System (at least each one) Mounted on a board. Ignition sys, Alternator, Self Starter, lighting sys, Head Light, Rear Lights, Stop lights, Wiper motor, Horn with suitable battery standard make |
| 62 | Different coloured automobile cablesBrown, Yellow, White, Green, Blue, Black 2.5 sq mm |
| 63 | Cooling System Components (Mounted on a board) Radiator, Water pump, Cooling Fan, V – belt, Thermostat valve and Hoses. |
| 64 | Lubrication System Components Strainer, Oil pump, PRV, etc. mounted on a board. |
| 65 | Compressor (in working condition) Single acting Reciprocating type, Cap 160 ltr |
| 66 | Gearbox (old) and clutch assembly. Cut Section Synchromesh, 5 speed |
| 67 | Fuse 5A, 10A, 15A, 20A |
| 68 | Some other item required Projector with screen Standard make with USB port |
| 69 | Working Bench 2.5 X 1.20 X 0.65 meters |
| 70 | Bench Vice 125 mm Jaw |
| 71 | Table for Instructor 4 ft. * 2.5 ft. |
| 72 | Chair For Instructor Standard make |
| 73 | Almirah Steel 2.5x1.20x0.5 meter |
| 74 | Hand Grinder 5 5000 RPM |
| 75 | Greace GunSmall |
| 76 | Mallet Hammer500 grams |
| 77 | Screw gauge |
| 78 | Center Punch |
| 79 | Automotive Puncture Repair kit For Tubeless and Tubed Tyre |
| 80 | Alignment Gauge (Manual) For Toe in/Toe out |
| 81 | First Aid Kit With general first aide things |
| 82 | Fire ExtinguisherABC type |
