Tender For Upgradation With (3 Year) Maintenance Of Electrical System Of Street Light Under Atal Industrial Infrastructure Mission Bhogoan Distt. Mainpuri
Tender Value
85.73 Lakhs
Estimated cost
Bid Submission
26 Jun 2023
0 days left
EMD
1.71 Lakhs
Bank guarantee accepted
Document Fee
3371
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
bhogaon → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Upgradation With (3 Year) Maintenance Of Electrical System Of Street Light Under Atal Industrial Infrastructure Mission Bhogoan Distt. Mainpuri
BOQ
| Sl. No. | Item Description |
| 1 | S/F of 63 Amp. 415 V metal clad TPN CFS complete with HRC fuse etc. on angle iron frame complete in all respects. Cat-B as per PWD Sch. No. 352 |
| 2 | S/F of (25 Amp.TPN) capacity of automatic street light cubical control panel painted with anti corrosive alkali and acid proof paint consisting of timer switch TSO 100 series with contactors HRC fuses, isolating switch metering instrument & instrument box with CTS etc. in case of TPN, as per PWD Sch. No. 807 f(ii) |
| 3 | Supply and wiring of sub main with 02 nos.of 2.5 sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in existing conduit complete with supply of all material labour and T&P required for proper completion of work as directed E/I as per PWD Sch. No. 289 |
| 4 | S/F of wiring cable (3Cx1.5 Sq.mm copper wire) for High Mast lighting system complete including all T&P men and material required for proper completion of work |
| 5 | Supplying and laying of aluminium conductor PVC insulated, armoured, served, sheathed cable 1100 V grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand alround and protected with burnt bricks on sides and on top complete in all respects. as per PWD Sch. No. 501(k) 35 sq.mm 3.5 core |
| 6 | Supplying and laying of aluminium conductor PVC insulated, armoured, served, sheathed cable 1100 V grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand alround and protected with burnt bricks on sides and on top complete in all respects. as per PWD Sch. No. 501(i) 16 sq.mm 4 core |
| 7 | Supplying and laying of aluminium conductor PVC insulated, armoured, served, sheathed cable 1100 V grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand alround and protected with burnt bricks on sides and on top complete in all respects. as per PWD Sch. No. 501(c) 16 sq.mm 2 core |
| 8 | S/F of brass nickel plated compression gland for PVC insulated and armoured served sheathed, underground cable including rubber ring etc. complete in all respects. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-incharge as per UPPWD Sch. No. 503 (k) 35.mm 3.5 core |
| 9 | S/F of brass nickel plated compression gland for PVC insulated and armoured served sheathed, underground cable including rubber ring etc. complete in all respects. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-incharge as per UPPWD Sch. No. 503 (i) 16.mm 4 core |
| 10 | S/F of brass nickel plated compression gland for PVC insulated and armoured served sheathed, underground cable including rubber ring etc. complete in all respects. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-incharge as per UPPWD Sch. No. 503 (c) 16.mm 2 core |
| 11 | S/F of palm or pin type copper tin plated cable socket (lug) to the cable leads insulating with tap and making connection etc. complete in all respects as per direction of the Engineer-incharge as per UPPWD Sch. No. 504 (e) 25 sq.mm |
| 12 | S/F of palm or pin type copper tin plated cable socket (lug) to the cable leads insulating with tap and making connection etc. complete in all respects as per direction of the Engineer-incharge as per UPPWD Sch. No. 504 (d) 16 sq.mm |
| 13 | Supply & fixing of LED Street light Fitting with mandatory driver set having die cast aluminium body and lenses suitable for 90 watt andconfirming to IP 66 protection having Company Logo Engravedcomplete in all respect as per UPPWD Sch. No.1423 CAT- AA (Philips/Cromption/Bajaj /Wipro make) |
| 14 | Supply & Fixing of factory wired integral LED floodlight luminaries with die cast aluminium housing built with driver set suitable for 200 watt confirming to IP 66 protection complete in all respect as per UPPWD Sch. No. 1455Cat.-AA (Philips/Cromption/Bajaj /Wipro make) |
| 15 | Supply & Fixing of factory wired integral LED floodlight luminaries with die cast aluminium housing built with driver set suitable for 150 watt confirming to IP 66 protection complete in all respect as per UPPWD Sch. No. 1454Cat.-AA (Philips/Cromption/Bajaj /Wipro make) |
| 16 | Supply & fixing of 32 mm dia, 1.20 M long G.I. Pipe bracket including bending of G.I. Pipe, 2 nos. 50x6 mm MS flat clamp in all respects with testing & commissioning of LED light complete in all respect. |
| 17 | Supply & fixing of LED Strip light with red, white and green (3 colour) in overall 18 Mtr. length (each colour 6 mtr.respectively) complete with LED strip driver (3 Nos. for each colour) etc. (complete with 01 year warranty for replacement from the date of work completion) complete in all respect as per direction of E/I |
| 18 | Lowring of 30 Mtr.High mast lighting system complete in T&P men & material required proper completion of work etc. complete in all respect as per direction of E/I |
| 19 | S/F of Male-Female plug & socket for High Mast lighting system complete including all T&P men and material required for proper completion of workcomplete in all respect as per direction of E/I |
| 20 | Supply & fixing of D clamp of size 50mm x 6mm flat iron on ST poles/steel rail poles with bolts,nuts and washers etc.complete in all respects including painting with aluminium paint as per UPPWD Sch. No. 623 |
| 21 | Supply & fixing of 100 x 110 mm shackle insulator 100 x 80 mm pin insulator including holes for shakcle insulator including, GI Bolts/ spindle nuts etc. complete in all respect as pre UPPWD Sch. No. 621 |
| 22 | Supply, sagging, tensioning ,jointing and binding of insulated ACSR Weasel conductor including cost of aluminium tape binding and jointing sleaves etc. complete in all respect |
| 23 | Supply & erection of stay set for LT lines including all fixtures, materials, labour and T&P, men & material required for proper completion of work as per PWD schedule no. 630 (Note: In case of LT/HT Stay a stay insulator shall be provided) as per direction of Engineer in charge complete in all respectas per UPSIDC Sch. No.14. 6(A) |
| 24 | Repairing of 9/11 Mtr. ST pole with 3 nos. MS channel welding method including 1/6 over all length of pole grouted with cement concrete in 1:3:6 (1 cement : 3 coarse sand : stone ballast) including plinthing of pole 30 cm above the ground level, plastering of plinth including exacavation back filling etc. including all T&P, men & material for proper completion of work as per direction of Engineer in charge complete in all respect |
| 25 | Painting of ST pole for L.T mains including fly stay & structure, 2 coats of aluminium paints with an under coat of red oxide paint pole above 10 M. long as per direction of Engineer in-charge of work/site including all T&P, men & material for proper completion of work as per UPSIDC Sch. No. 24.20(A) |
| 26 | (Supervision) Supply&errection of double pole structure with hardware & fittings on 410 SP-56,11 mtr. Long complete with 1/6 th of over all length of pole in cement concrete with one feet square/one feet dia cement ,concrete plinth around the pole above ground level . The foundations of underground will be of cement concrete in the ratio 1:2:4 .The stone ballast/brick-ballast used will be 1.25 cm (1/2x1) size with the stone pad 30x30x7.5 cm at the base , including all T&P, men & material for proper completion of work as per direction of Engineer in charge |
| 27 | Supply&errection of Stay set of HT Line for ST pole with GI anchor plate(152x152x6mm) stay rod (16mm dia x 1.85 mtr.long) GI stay below (16 mm dia, thriple ,double stay, tightener ,stay insulator ,clamps & stay wire (GS 7/13 .15 mm) including grouting in 1:4:8 ratio of cement concrete using course sand ,over brunt brick ballast. including all T&P, men & material for proper completion of work as per direction of Engineer in charge |
| 28 | Supply & fixxing of 11 KV pin with insulator on channel arm fixed on ST/DP including cost of nuts,bolts,washers,T&P men & material for proper completion of work as per direction of Engineer in charge |
| 29 | Supply & fixxing of anticlimbing device fabricated grom G.I flat of 25mmx6mm size in a sape of ring of the pole size, having G.I flat pointed fins of the length 225 mm in 8 nos. and also barbed wire in 200 mm length above the said ring including material for proper completion of work as per direction of Engineer in charge |
| 30 | Supply & fixxing of 11 KV disc with insulator with galvanised insulator ,ball and socket type complete with strain clamps nuts,bolts,washers,T&P men & material for proper completion of work as per direction of Engineer in charge |
| 31 | Supply & fixxing of M.S Top channel of 125x65x2240 mm including cost of holding clamps and materials for proper completion of work as per direction of Engineer in charge |
| 32 | Supply & fixxing of M.S droper channel of 100x50x2000 mm including cost of holding clamps and materials for proper completion of work as per direction of Engineer in charge |
| 33 | Supply & Fixxing of 11 KV TPMO with complete with insulator & other accessories (Relco/Azad/Rama/other standard make as approved by UPPCL) proper completion of work as per direction of Engineer in charge |
| 34 | Supply and fixing of danger board 11 KV line with clamp of size 25 x3 mm flat with nut & bolts complete in all respect as per direction E/I as per SIDC E27.01 |
| 35 | Supply,sagging,tensioning,jointing and binding of ACSR Weasel conductor including cost of aluminium tape binding wire and jointing sleeves complete in all respects including material,men an T&P for proper completion of work.UPSIDC E.10.(a) |
| 36 | S/F of 11 kV three phase D.O. fuse set complete with suitable clamps, nuts & bolts, fuse wire etc.as per direction of Engineer in charge |
| 37 | Supply and installation,testing & commissioning of outdoor type aluminium wound oil cooled transformer of ratings 25 KVA, 11/.04 KV on double pole including cost of base channel & holding clamps.complete as per IS-1180-2014 (Discom Approved Make) proper completion of work as per direction of Engineer in charge |
| 38 | Supply & laying 70 sq mm 3 core Al. conductor XLPE insulated PVC bedded galvanised flat steel striparmoured, served, sheated cable 1100 V grade laid with brick ,sand with 75 cm deep below the ground level. The armouring of the cable shall be properly connected with earth conductor by clamp etc. as per PWD Sch. 506(d) (Polycab/Havells/Grandlay/Gloster Make) |
| 39 | Supply & Laying of 90 mm dia (OD-90 mm & ID-76 mm nominal) DWC HDPE pipe ISI marked along with all accessories like socket, bend,couple etc. confirming to IS 14930 Part-II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning andprotective covering etc. complete in all respect . |
| 40 | Supply & Laying of 90 mm dia (OD-90 mm & ID-76 mm nominal) DWC HDPE pipe ISI marked along with all accessories like socket, bend,couple etc. confirming to IS 14930 Part-II complete with fitting and cutting, jointing etc.througth horizontal boring trenchless (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. |
| 41 | S/F of outdoor/indoor type 11 KV jointing kit heat shrinkable type for 11 KV cable including cost of all material, labour, T&P etc. for proper completion of work.(Raychem, Denson/Birla /3M make) for 3 core x 70 sq.mm cable. |
| 42 | Supply & fixing of 11 KV straight through jointing kit heat shrinkable type for 11 KV cable including cost of all material,labour, T&P etc. for proper completion of work (Raychem/Denson/Birla/3M make) for 70x3 sq.mm cable. |
| 43 | Supply & fixing of welded wire mesh fencing of 5x3x2.4 meter and 2x2.4 M gate including excavation base concrete & brick work with back filling etc. complete in all respect. |
| 44 | S/B of 600x600x6mm G.I. plate vertically for earthing with its top at least 3 M. below ground level complete with 20 mm dia G.I.pipe and funnel for watering and one earthing lead of one no. 8 to 10 SWG GI wire in 15 mm dia G.I.pipe up to switch board ( from appron to switch board the cost of G.I.pipe and G.I. wire be extra) 30 cm square C.I. frame with hinged cover masonry housing alternate layers of charcole /Coke and salt at least 150mm thick around etc. as per directions of Engineer-in-charge complete in all respect as per as per drawing as per UPPWD Sch. No. 702 |
| 45 | Supply & fixing of 100 mm dia G.I.pipes \"B\" class for climbing up the cable from ground to over head line including all accessories, material, labours and T&P required for proper completion of work as per specification as per SIDC Sch. No. 25.1 |
| 46 | AMC Supplying and laying of aluminium conductor PVC insulated, armoured, served, sheathed cable 1100 V grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand alround and protected with burnt bricks on sides and on top complete in all respects. as per PWD Sch. No. 501(j) 25 sq.mm 3.5 core |
| 47 | S/F of 16 Sq.mm, 2 core PVC insulated PVC sheathed armoured 1100 V grade Al. conductor cable laid to depth of 750 mm below ground level over a cushion of 75 mm thick sand alround and protected with burnt bricks on sides and on top complete in all respects as per PWD Sch. No. 501 © |
| 48 | S/F of brass nickel plated compression gland for PVC insulated and armoured served sheathed, underground cable including rubber ring etc. complete in all respects. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-in charge as per UPPWD Sch. No. 503 (c) 16 sq.mm 2 core |
| 49 | S/F of brass nickel plated compression gland for PVC insulated and armoured served sheathed, underground cable including rubber ring etc. complete in all respects. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-in charge as per UPPWD Sch. No. 503 (j) 25 sq.mm 3.5 core |
| 50 | S/F of palm or pin type copper tin plated cable socket (lug) to the cable leads insulating with tap and making connection etc. complete in all respects as per direction of the Engineer-in charge as per UPPWD Sch. No. 504 (d) 16 sq.mm |
| 51 | S/F of palm or pin type copper tin plated cable socket (lug) to the cable leads insulating with tap and making connection etc. complete in all respects as per direction of the Engineer-in charge as per UPPWD Sch. No. 504 (e) 25 sq.mm |
| 52 | Supply & wiring of submain with 2 Nos. of 2.5 sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in existing conduit complete with supply of all material labour and T&P required for proper completion of the work as directed as site by Engineer I/C as per UPPWD Sch. No.289 |
| 53 | S/F of wiring Cable(3Cx1.5 Sq.mm copper wire) for High Mast lighting system complete including all T&P men and material required for proper completion of work |
| 54 | Supplying and wiring of 4 sq. mm aluminium conductor PVC insulated unsheathed single core cable including all T&P men and material for proper completion of work |
| 55 | Supply, sagging, jointing and binding of insulated ACSR Weasel conductor including cost of aluminium tape binding and jointing sleaves etc.complete in all respect |
| 56 | Supply & fixing of D clamp of size 50x6 mm flat iron on ST poles with nuts and washers etc. complete in all respect as per UPPWD Sch. No. 623 |
| 57 | Supply & fixing of 100 x 110 mm shackle insulator 100 x 80 mm pin insulator including GI volt spindle, nuts etc. as pre UPPWD Sch. No. 621 |
| 58 | Supply & Fixing of 32 Amp 415 V metal clad TPN rewireable type switch fuse unit on angle iron bracket complete in all respects as per UPPWD Schedule No. 315 Cat-B |
| 59 | Supply & Fixing of 63 Amp 4 pole MCB complete in all respects as per UPPWD Schedule No.1020(A) Cat-B |
| 60 | Lowring of 30/16 Mtr. High mast lighting system complete in T&P men & material required proper completion of work as per direction of Engineer-in charge |
| 61 | Dismentaling&Re-installation of 30/16 Mtr. High mast lighting system on existing plinth complete in T&P men & material required proper completion of work as per direction of Engineer-in charge |
| 62 | S/F of S.S. wire rope set Suitable for 30/16 Mtr. High Mast lighting system as per specification complete including all T&P men and material required for proper completion of work as per direction of Engineer-in charge |
| 63 | S/F of Trailing Cable Suitable for 30/16 Mtr. High Mast lighting system as per specification complete including all T&P men and material required for proper completion of work as per direction of Engineer-in charge |
| 64 | S/Oiling of winch machine for High Mast lighting system complete including all T&P men and material required for proper completion of work as per direction of Engineer-in charge |
| 65 | S/F of Male-Female plug & socket for High Mast lighting system complete including all T&P men and material required for proper completion of work as per direction of Engineer-in charge |
| 66 | S/F of ML-4 contactor MDS/L&T make complete including all T&P man and material required for proper completion of work as per direction of Engineer-in charge |
| 67 | S/F of mounting time switch (timer clock) L&T/MDS make complete including all T&P men and material required for proper completion of work as per direction of Engineer-in charge |
| 68 | Charges for maintenance, Proper Watch&ward of entire electrical system of Street light, High Mast Tower, cables,conductors,poles,panels etc. all other available material as per direction of Engineer-in charge etc. for road lighting in IA to cover the general supervision for execution of work including dismantling & re-fixing of all street light of UPSIDA during the period of AMC for (36 Months) (With manpower- 01 Electrician & 01 Helper) |
| 69 | Cost of all material, spares wire fuses, small accessories required for general maint., cleaning, oiling etc. to keep the entire installation in perfect working order during AMC period. (L.S. Basis) |
| 70 | S/F of following capacity of automatic street light cubical control panel painted with anti corrosive alkali and acid proof paint consisting of timer switch TSO 100 series with contactors HRC fuses, isolating switch metering instrument box with CTS etc. (40 Amp. TPN) as per PWD Sch. No. 807 F |
AI Tender Summary
Tender Timeline
Jun 17, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedJun 26, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 27, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender