|
| 1 | M&L for Dehydration including filtration and cleaning of Voltage stabilizer oil by dehydrating machine incl testing of sample before and after dehydration and filtration and replacement of silica gel complete all as specified and directed by Engr-in-Charge.Note:- dehydration machine and testing kit will be provided by the Dept. but transpotation of machine is the responsibility of Contractor withoutany extra cost to the dept. Sample testing will be carried out in the presence of Engr-in-Charge on site. |
| 2 | Supply & Filling /pouring of up to the appropriate level Voltage stabilizer oil of low viscosity having dielectric strength not less than 60 KV complete all as specified and directed by Engr-in-Charge. Note:-Dielectric strength test shall be carried out at site before poring/filling in transformers in the presence of Engr-in-Charge on the site. |
| 3 | Supply, jointing and testing End termination cable joint heat shrinkable including all material and accessories suitable for 4 core X 25-95 Sqmm XLPE cable of 1100 volts (E)grade complete all as specified and directed by Engr-in-Charge. Note : Cost of Prepration of existing end deemed to be included in unit rate. |
| 4 | All as per serial item No 3.00 here-in-before but of size 3.5 core X120sqmm- 185 sqmm complete all as specified and directed by Engr-in-Charge. |
| 5 | All as per serial item No 3.00 here-in-before but of size3.5 core X185sqmm complete all as specified and directed by Engr-in-Charge. |
| 6 | Supply, jointing and testing Straight through cable joint heat shrinkable including all material and accessories suitable for 4 core X 25-95 Sqmm XLPE cable of 1100 volts (E)grade complete all as specified and directed by Engr-in-Charge. Note : Cost of Prepration of existing end deemed to be included in unit rate. |
| 7 | All as per serial item No 6.00 here-in-before but of size 3.5 core 120sqmm- 185 sqmm complete all as specified and directed by Engr-in-Charge. |
| 8 | All as per serial item No 6.00 here-in-before but of size3.5 core X185sqmm complete all as specified and directed by Engr-in-Charge. |
| 9 | Comprehensive maintainance of oil cooled servo voltage stablizer by isolating ,disconnecting of input/output ,supply cable,opening of top of voltage stablizer,detecting of fault ,u/s component in control panel /dimmerstat /PCB etc,cleaning of serviceable parts/ component , cleaning strain grease /oily spots with tinner & replacement of worn out spare parts etc, if required all as specified and directed by Engr-in-Charge. |
| 10 | Voltage stablizer of capacity 600 KVA three phase complete all as specified and directed by Engr-in-Charge. |
| 11 | Voltage stablizer of capacity 400/450 KVA three phase complete all as specified and directed by Engr-in-Charge. |
| 12 | Voltage stablizer of capacity250/200 KVA three phase complete all as specified and directed by Engr-in-Charge. |
| 13 | Voltage stablizer of capacity 100 KVA three phase complete all as specified and directed by Engr-in-Charge. |
| 14 | Micro Processor based control card for each phase complete all as specified and directed by Engr-in-Charge. |
| 15 | Servo synchronizing motor single phase AC 230 Volts, 3 Kg torque complete all as specified and directed by Engr-in-Charge. |
| 16 | RC Net work for 3 Kg torque servo motor complete all as specified and directed by Engr-in-Charge. |
| 17 | Carbon Brush of any capacity complete all as specified and directed by Engr-in-Charge. |
| 18 | Dismantling existing ACSR conductor of any size/type from PCC/Steel poles including taking down MS works such as cross arms, clamps, hooks, stay etc from overhead line complete all as specified and directed by Engr-in-Charge.Note: Retrived ACSR Conductor scrap shall be deposited AGE E/Mstoreyard with own arrangement by the contractor |
| 19 | Taking down/Removing existing PCC/Steel poles from site complete all as specified and directed by Engr-in- Charge. Note: Damaged poles shall be removed from site as per direction of Engr-in-Charge. |
| 20 | Taking down existing old cross arms of MS channel or angle sections etc complete all as specified and directed by Engr-in-Charge. |
| 21 | Taking down old unserviceable insulators any type and size from poles including for reuse or removal complete all as specefied and directed by Engr-in-Charge. |
| 22 | Supply & fixing in replacement lighteneing arrestors expulsion type complete with all fittings, suitable for 11000 Volts grade transmission class, discharge capacity 65KA including brackets, clamps, nuts, washers and connecting to 4mm dia GI earth wire complete all as specified and directed by Engr-in-Charge. |
| 23 | S & FAluminium conductor steel reinforced (ACSR) any size on poles, stretched on LT poles without any kink and bends of various sizes complete including fixing to insulator with Aluminium binding wire complete all as specefied and directed by Engr-in-Charge. |
| 24 | Supply & Fix 11000 volts grade disc type insulator porcelain vitreous 145mm heigh 255mm dia ball and socket type white or brown or green with tension clamps complete all as specified and directed by Engr-in-Charge. |
| 25 | Supply & Fix pin type porcelain vitreous white or brown or green insulator including one galvanized mild steel spindle, two galvanised iron washers and one galvanised iron nut,150mm height,150mm dia for 11000 volts grade complete all as specified and directed by Engr-in-Charge. |
| 26 | S&F in replacement MS Channel/angle iron/flat iron of required size and bend to shape as cross arms, bracing and support including, MS clamps back plates with bolts, nuts, and washers drilled for insulators including painting two coats of synthetic enemel paint (Aluminium shade) over a coat of red oxide primer complete all as specefied and directed by Engr-in-Charge. |
| 27 | Suppling, fixing and erectingsteel tubular swaged poles erected to truly vertical or planted as strut complete with 6mm thick mild steel base plate(300mmx300mm), welded to pole, finial taper plug, bolts, nuts, and screws poles made out of ERW MS tubing conforming to IS-2713 Part-II Type 410 SP-55, 11.0 mtr long including drilling of holes of required size for fixing of cross arms, painting the exposed surfaces of pole with two coats of aluminum paint over a coat of red oxide zinc chrome primer and with two coats of black bitumenous paintinternally and portion embedded in concrete, making five black & white bands at lower portion of pole each 300mm wide alternately upto the height and marking pole No. with black paint at suitable height including making two nos holes of suitable size in steel tubular pole by gas welding for passing PVC cable connection from junction box to security lights through pole where junction box to be fitted in pole, complete all as specified and directed by Engr-in-Charge. Note: Cost of Excavation, Earth Work and PCC in foundation are deem to be included in quoted rate. |
| 28 | MCCB 4 Pole, 415 V, fixed type, 100 Amps with breaking capacity 16 KA complete all as specified and directed by Engr-in-Charge. |
| 29 | MCCB 4 Pole, 415 V, fixed type, 125 Amps with breaking capacity 16 KA complete all as specified and directed by Engr-in-Charge. |
| 30 | MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA complete all as specified and directed by Engr-in-Charge. |
| 31 | MCCB 4 Pole, 415 V, Adjustable type, 200 Amps with breaking capacity 36 KA complete all as specified and directed by Engr-in-Charge. |
| 32 | MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 KA complete all as specified and directed by Engr-in-Charge. |
| 33 | MCCB 4 Pole, 415 V, Adjustable type, 400 Amps with breaking capacity 36 KA complete all as specified and directed by Engr-in-Charge. |
| 34 | Supply & fix Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for LT, 20x15cm size complete all as specified and directed by Engr-in-Charge. |
| 35 | Supply & fix in replacement for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge plate not less than 1.5 metre below normal ground level connected to galvanized earth strip of size 25 x 4 mmas earthing lead by means of bolts,nuts,chuck nuts and washers of galvanized iron earth lead with 15 cm thick alternate layers of charcoal dust & common salt including PCC pit in PCC 1:2:4 type B-1,RCC covermade out of cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) reinforced with TMT steel bars 8 mm dia @150 mm c/c both ways with suitable handle andangle iron 40x40x5mm frame,GI medium grade watering pipe 20 mm bore and funnel with wire mesh light grade protection pipe 40 mm bore up to main board complete as shown on electrical plate No 3 of MES Sch 2009 (Part-I) and testing on completion complete all as specified and directed by Engr-in-Charge. |
| 36 | Note: - (i) On testing after completion of earthing,if desired earth resistance is not obtained,the earthing will be re-done by the contractor at his own risk & cost to the entire satisfaction of Engir-in-Charge.(ii) Item includes the cost of 7.5 m GI pipe for protection of earth strip.(iii) PCC pits extra cost of addtional length of watering pipe, bends elbows etc.shall be deemed to be included in the quioted rate. (iv) Item includes the cost of 7.5 mtr length copper earth strip 25x4 mm. |
| 37 | Supply & fix in replacement for earth continuity conductor or main earthing lead fixed to wall on batton or recess or chases or buried in ground or drawn in conduit/ pipe or fixed to pole or any other indicated situation for loop earthing etc as required with 32x6mm galvanised iron strip complete all as specified and directed by Engr-in-Charge. |
| 38 | Supply and Fixing in replecement LED Decorative Garden/post-top light for 360 degree indirect lightIP-65 grade of proterction withHigh power LED of 20 wattwith resistance to impact and corrosion. Glare free and betteruniformity.Milky version complete all as specified and directed by Engr-in-Charge.Note : Foundation for fixing Garden light/Post top light shall be deemed to be included in the rates quoted by the Contractor. |
| 39 | Supply and fixing Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled, screwed including 3 nos. 8mm dia 25mm long hex. head screw & brezing all jointscomplet all as specified anddirected by Engr-in-Charge. |
| 40 | Taking down GI strip/ Copper strip 20 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and directed by Engr-in-Charge. |
| 41 | Disconnecting the bindings of loose overhead conductor of LT/HT lines from insulators and restringing the same for proper sag and rebinding with new aluminium binding wires at insulators, making all jumpers and inter connections of conductors at cut points as well as turnings using PG clamps of suitable size as per size of conductor for any type of conductor including restringing of continuous GI earth wire complete all as specified and directed by Engr-in-Charge. Note :- (i) Trimming of tree branches upto 3 m all around the conductors is deemed to be included in the rates quoted. (ii) Three ACSR conductors and two GI earth wire will be measured as one unit length for payment. (iii) Cost of PG clamps, aluminium winding wire and eye hook for GI earth wire are included in the rates coated for restringing. |
| 42 | Supply and fixing in replecement of Lead acid maintenance free Battry12 Volts 180 AH of existing type & size suitable for complete all as specified and directed by Engr-in-Charge. |
| 43 | S&F LED indicator lamp for LT/HT panel (Red / Green/Blue/Yellow) complete all as specified and directed by Engr-in-Charge. |
| 44 | S&F ammeter & Voltmeter Selector switch of LT /HT panel complete all as specified and directed by Engr-in-Charge. |
| 45 | M&L for multy function meter input 3 Phase 4 Wire, Voltage Range 300V AC (L-N)/520V AC(P-P), Display Paremeter : Voltage (p-p) (P-L), Amp (R,Y,B) Current : 0-5A , CT 05-6000A insttalled on LT panel including necessory wiring, CT of required size complete all as specified and directed complete all as specified and directed by Engr-in-Charge. |
| 46 | Supply, laying, jointing and testing XLPE insulated,PVC outer sheathed, galvanised steel strips armoured, heavy duty power cable with aluminium conductor suitable for rated voltage of 1100 Volts grade earthed system and conforming to IS : 7098of 1995 and of size 3.5 core X 185Sqmm and laid in trenches/ducts/pipe or on poles complete all as specified and directed by Engr-in-Charge.Note : (i)Excavation, earthwork, Sand Cushioning, Cable covers, Pipe for cable protection to be measured and paid for separately)(ii)Retrived LT cable scrap shall be deposited AGE E/Mstoreyard with own arrangement by the contractor. |
| 47 | All as per serial item No 41.00 here-in-before but of size 3.5 core X 120 sqmm complete all as specified and directed by Engr-in-Charge. |
| 48 | All as per serial item No 41.00 here-in-before but of size 3.5 core X 95 sqmm complete all as specified and directed by Engr-in-Charge. |
| 49 | All as per serial item No 41.00 here-in-before but of size 3.5 core X 70 sqmm complete all as specified and directed by Engr-in-Charge. |
| 50 | All as per serial item No 41.00 here-in-before but of size 3.5 core X 50 sqmm complete all as specified and directed by Engr-in-Charge. |
| 51 | All as per serial item No 41.00 here-in-before but of size 3.5 core X 35 sqmm complete all as specified and directed by Engr-in-Charge. |
| 52 | All as per serial item No 41.00 here-in-before but of size 4 core X 25 sqmm complete all as specified and directed by Engr-in-Charge. |
| 53 | All as per serial item No 41.00 here-in-before but of size 4 core X 16 sqmm complete all as specified and directed by Engr-in-Charge. |
| 54 | All as per serial item No 41.00 here-in-before but of size 2 core X 10 sqmm complete all as specified and directed by Engr-in-Charge. |
| 55 | Excavation in trenches not exceeding 1.5 m wide and and not exceeding 1.5 m depth in Hard/dense soil and getting out complete all as specified and directed by Engr-in-Charge. |
| 56 | Returning, filling in, with excavated soil including spreading, levelling, watering and well ramming in layers not exceeding 25 cm, complete all as specified and directed by Engr-in-Charge. |
| 57 | Removal of surplus soil to distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge. |
| 58 | Supply and lay DWC ( Double wall corruated ) pipe 120 x 103 mm conforming to IS 14930/ IS 16205 for protection of LT / HTCable of size 95 sqmm including neccesory Snap-Fit cuppler required for fixing complete all as specified and directed by Engr-in-Charge. |
| 59 | All as per serial item No 51.00 here-in-before but of size 90/76 mm for xlpe cable 3.5 core X 95 sqmm complete all as specified and directed by Engr-in-Charge. |
| 60 | All as per serial item No 51.00 here-in-before but of size 77/63 mm for xlpe cable 3.5 core X 70 sqmm-10 smmm complete all as specified and directed by Engr-in-Charge. |
| 61 | Taking downthe existing cables from trenches of any size complete all as specified and directed by Engr-in-Charge. |
| 62 | Supply, lay and fix aerial bunched cable 11KV grade stranded and compact aluminium phase conductor of size 3.5x120 sqmm + 1x70 sqmm (bare messenger) with Aluminium alloy. The phase conductor shall be insulated with XLPE (Sioplas) compound Aluminium as per IS-14225-1995including all fittings such as anchor clamp, suspension clamp, line connector, service clamp, insulator piercing connectors, for taps from bare line etc. complete all as specified and as directed by Engr-in-Charge. |
| 63 | All as per serial item No 55.00 here-in-before but of size 3.5x95sqmm + 1x50 sqmm complete all as specified and directed by Engr-in-Charge. |
| 64 | All as per serial item No 55.00 here-in-before but of size 3.5x70sqmm + 1x50 sqmm complete all as specified and directed by Engr-in-Charge. |
| 65 | Supply & Fix sintex IP 56 LT ABC conductor junction box suitable for ABC conductor cable size upto 120 sqmm complete all as specified and as directed by Engr-in-Charge. |
| 66 | S&F end termination joint kit, heat shrinkable type suitable for 70to 95 sqmm ABC conductor Cable complete all as specified and directed by Engr-in-Charge. |
| 67 | S&F end termination joint kit, heat shrinkable type suitable for 120 sqmm ABC conductor Cable complete all as specified and directed by Engr-in-Charge. |
| 68 | S&F straight through joint kit, heat shrinkable type suitable for 70to 95 sqmm ABC conductor Cable complete all as specified and directed by Engr-in-Charge. |
| 69 | S&F straight through joint kit, heat shrinkable type suitable for 120 sqmm ABC conductor Cable complete all as specified and directed by Engr-in-Charge. |
| 70 | Supply ,installation ,testing and commissioningin replacement of feeder pillar boardKiosktype ,LT(415 Volts, 50 Hz , 3-phase, 4 wire supply) floor mounted , factory assembled, outdoor typeweather and vermin proof (Protection Class IP-54) made out of 40m x 40mm x 6mm angle iron frame and 3.15 mm thick MS Sheet CRCA sheet with front hinged opening, rubber lining, locking arrangement ,powder coated externally and internally after seven tanks treatmentand lifting channel, fully compartmentalized design complete Bus Bar chamber comprising incomer MCCB 315 Amp, 4 Nos aluminium strip bus bars air insulated and PVC sheathed capacity 400 Amps with colour coding complete all as specified and directed by Engr-in-Charge.Note : (i) Retrived LT feeder pillar board shall be deposited AGE E/Mstoreyard with own arrangement by the contractor . |
| 71 | Supply ,installation ,testing and commissioningin replacement of feeder pillar boardKiosktype ,LT(415 Volts, 50 Hz , 3-phase, 4 wire supply) floor mounted , factory assembled, outdoor typeweather and vermin proof (Protection Class IP-54) made out of 40m x 40mm x 6mm angle iron frame and 3.15 mm thick MS Sheet CRCA sheet with front hinged opening, rubber lining, locking arrangement ,powder coated externally and internally after seven tanks treatmentand lifting channel, fully compartmentalized design complete Bus Bar chamber comprising 4 Nos aluminium strip bus bars air insulated and PVC sheathed capacity 400 Amps with colour coding complete all as specified and as directed by Engr-in-Charge.Note : (i) Retrived LT feeder pillar board shall be deposited AGE E/Mstoreyard with own arrangement by the contractor. |
| 72 | Decarbonising of LT Panel board / Feeder pillar boxes by CTC( Carbon Tetra Chloride), removing the carbon deposited inside the panel, cleaning the panel with cotton waste,applying one coat of becktol red solution, checking the faults inside the panel board and charging the LT Panel post completion of decarbonisation complete all as specified and directed by Engr-in-Charge. Note :(a) Proper shut down shall be taken prior the commencement of work . (b) Contractor shall provide 2 bottles of (250ml) - CTC . Cotton waste of not less than -1kg and Dr Bectol solution (250ml) - 1 no for performing the decarbonisation. (c) Fabrication of LT Panels for broken hinges shall be rectified. (d) LT Panel shall be painted withtwo coats of synthetic enamel paint over a coat of red oxide primer.(e)Marking on LT panels shall be done as per sources of power supply (1100 volts) and outgoing area by 10cm glow sign/paint all as directions of Engr-in-Charge. |
| 73 | Supply & Fix in replacement PVC sheathed Twin core Aluminium conductor cable 6 sqmm complete all as specified and directed by Engr-in-Charge. |
| 74 | Supply & Fix in replacement PVC sheathed Twin core Aluminium conductor cable 10 sqmm complete all as specified and directed by Engr-in-Charge. |
| 75 | Supply & fixing Onload change over switch FP400 Amps, side handle, 415 Volt, 4 pole 50 Hz, including neccesory addition / altration in panel for mounting and providing Busbar, Nut bolts & Washerscomplete all as directed by Engr-in-Charge. |
| 76 | Supply & fixing Onload change over switch FP200 Amps, front handle, 415 Volt, 4 pole 50 Hz, including neccesory addition / altration in panel for mounting and providing Busbar, Nut bolts & Washerscomplete all as directed by Engr-in-Charge. |
| 77 | Supply & fixing Onload change over switch FP200 Amps, Side handle, 415 Volt, 4 pole 50 Hz, including neccesory addition / altration in panel for mounting and providing Busbar, Nut bolts & Washerscomplete all as directed by Engr-in-Charge. |
| 78 | Supply & fixing Onload change over switch FP125/100 Amps, side handle, 415 Volt, 4 pole 50 Hz, including neccesory addition / altration in panel for mounting and providing Busbar, Nut bolts & Washerscomplete all as directed by Engr-in-Charge. |
| 79 | Supply & fixing Onload change over switch FP63 Amps, side handle, 415 Volt, 4 pole 50 Hz, including neccesory addition / altration in panel for mounting and providing Busbar, Nut bolts & Washerscomplete all as directed by Engr-in-Charge. |
| 80 | Supply and fixing weather proof street light junction box of size 300 x 200 x 105mmincluding MCB SP 6 Amps and connecting terminals 4 way and fixing with street light poles using necessary MS clamps, nuts, bolts washers, lugs for incoming and out going cables, gland for cable etc of suitable size complete all as specified and as directed by Engr-in-ChargeNote : The rates quoted are inclusive of provision and fixing of suitable lugs and glands for cable connection. |
| 81 | Cleaning the existing exposed surfaces of steel tubular pole of9.0 mtr long including cross arms, brackets, clamps etc and painting with two coats of aluminium paint marking five black & white bands at lower portion of pole, Each 300 mm wide alternately and marking pole No. with yellow paint on black base at suitable height complete all as specified and directed by Engineer-in-Charge. |
| 82 | S&F in replacement 120 Watt LED Flood light with pressure die cast aluminium housing & toughened glass with IP-66 degree protection, individual LED\"s must have peanut lenses for better throw across & along the road with luminarie efficacy of greater than 110 lumen/Watt (Minimum lumen output of luminarie should be 16500 Lumens) color rendering (CRI) of > 75 and co-related color temperature (CCT) of 5700K (+ 500K), The luminarie should have 5 KV surge protection,PF > 0.95, and total harmonic distortion of THD < 10%, voltage range of 140-280V should be provided.Luminarie should have top maintainable driver compartment for easy access to driver during maintenance.The driver used must be a constant current driver with efficiency of > 85%.The manufactures LOGO must be embossed/Engraved in the housing of the luminarie. Manufactures to provide LM80 from source manufacturer and should have adequate testing facilities approved by ministry of science (Govt of India) to provide LM 79 report complete all as specified and directed by Engineer-in-Charge. |
| 83 | All as per serial item No 77.00 here-in-before butof capacity 60 watt LED complete all as specified and directed by Engr-in-Charge. |
| 84 | All as per serial item No 77.00 here-in-before but of capacity 90 watt LED complete all as specified and directed by Engr-in-Charge. |
| 85 | M&L for bracket for street light fitting made of 40mm bore lightgrade GI tube bent to shape required, Sutable for fixing on pole includingfixed with bolts, nuts, washers duly painting the bracket with two coats of aluminium paint over a coat of zinc chrome primer complete including taking down the existing bracket and refixing and connecting up the light fitting etc complete all as specified and directed by Engr-in-Charge. |
| 86 | Supply and fix in replacement ofautomatic timer switch pole mounted enclosure consisting of ON/OFF switch based on LUX level, power contactor 40 Amps, 4 pole, MCB 40 Amps, TP - 03 Nos, enclosure made of rust proof, shock proof, conforming to IP -54 complete all as specified and directed by Engr-in-Charge. Note: (i)Inlet/outlet connecting cable PVC insulated aluminium stranded conductor 6 Sqmm, 4 single core for incoming & outgoing up to 8 Mtr deemed to be included in the unit rate.(ii) Provn of glands and lugs shall be deemed to be included in the quoted rate. |
| 87 | M&L for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in coping etc including necessary form work and finishing the surface of PCC above ground level with cement mortar 1:4, 5mm thick complete all as specified and directed by Engr-in-Charge. |
| 88 | M&L for PCC 1:4:8 type D-2 (using 40 mm grade stone aggregrate in foundation, mass concrate) as in foundation of poles& stay etc complete all as specified and directed by Engr-in-Charge. |
| 89 | M&L for Rectification of leakage of UG water pipe lines of size 150 mm Bore of any description such as DI pipe line at any location by necessary excavation, earth work, dewatering, cutting existing pipe lines including repairs with suitable flanges, Joints or any other material complete all as specified and as directed by Engr-in-Charge.Note for Item No 84.00 to 94.00(i)Complaint shall be notified to contractor on mobile phone.Hence,it is mandatory to mention his mobile No. while quoting the tender.(ii)Complaint will be notified to contractor on mobile phone at any time between 0800 hrs to 2200 hrs and will be rectified within 12 hours after notification, failing which double of quoted rate per day per complaint will be recovered.(iii) Completion report of the complaint shall be given in writing and recorded in the register.(iv) Rates quoted shall be deemed to include the cost of T&P required. Pipes and Jointing material shall be measured and paid under relevant items of schedule\"A\" |
| 90 | All as per serial item No 84.00here-in-before but of size100mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 91 | All as per serial item No 84.00here-in-before but of size 80mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 92 | M&L for rectification of defective run lead joing by burning out lead joint in position including recovering lead and making new lead joint for 200 mm bore all as specified including bailing out water coming from defective joints by means of electric/diesel driven pump set, testing of the joint under full working pressure for the following CI Pipe lines all as directed by Engr-in-Charge. |
| 93 | All as per serial item No 87.00here-in-before but of size150mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 94 | All as per serial item No 87.00here-in-before but of size 100mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 95 | All as per serial item No 87.00here-in-before but of size 80mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 96 | Attending Complaints for rectification of leakage of UG water pipe lines of size 100 mm Bore of GI pipe at any location including necessary excavation, earth work, dewatering including Cutting existing line & Welding with new one or repairs with suitable flanges, Joints or any other material complete all as specified and as directed by Engr-in-Charge. |
| 97 | All as per serialitem No 91.00 here-in-before but for size 80mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 98 | All as per serialitem No 91.00 here-in-before but for size 50mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 99 | All as per serial item No 91.00 here-in-before but of size 40mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 100 | Attending leakage complaints of sluice valves 150mm bore by repacking stuffing box, removing gland plate and pumping/taking water from water pit and proving gland packing and refitting by replacing worn out bolts,nuts and washers complete all as specified.Note: bolts,nuts and washers should be included in quted rate. |
| 101 | All as per serial item No 95.00 here-in-before but of size100mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 102 | All as per serilaitem No 96.00 here-in-before but of size 80mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 103 | Drilling and tapping cast iron water mains (in position) for branch connections of the internal dia 15 mm complete all as specified and directed by Engr-in-Charge. |
| 104 | Drilling and tapping cast iron water mains (in position) for branch connections of the internal dia 20 mm complete all as specified and directed by Engr-in-Charge. |
| 105 | Demolition of existing valve pit chamber , M&L for masonry valve pit of size 900x900x900mm internal size complete with excavation, earth work and brick work in CM 1:6, 15mm thick plastering in CM 1:4 internally including5mm thick MS Sheet cover and angle iron frame of suitable size and two coats of synthetic enamel paint over one coat of red oxide primer complete with locking arrangement complete all as specified and directed by Engr-in-Charge. |
| 106 | S&F CI /DI Specials/fittings including breaking/taking out defective CI specials for spigot and socket end for CI mainsupto 150 mm dia complete all as specified and directed by Engr-in-Charge. |
| 107 | Supply and fix in replacement cast iron flanged drilled heavy duty sluice valve with ISI mark with stainless steel spindle and check nut and plan PN-1.6 complete with rubber insertion nuts and bolts with washers of size 150 mm bore etc complete all as directed by Engr-in-Charge. |
| 108 | All as per serial item No 102.00 here-in-before but of size 200mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 109 | All as per serial item No 102.00 here-in-before but ofsize 100mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 110 | All as per serial item No 102.00 here-in-before but of size 80mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 111 | Supply and fix Gun Metal globe or Gate valve iron wheel head screwed both ends for iron pipes of size 50mm dia bore complete all as specified and directed by Engr-in-Charge. |
| 112 | All as per serilaitem No 106.00 here-in-before but of size 40mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 113 | All as per serilaitem No 106.00 here-in-before but of size 25mm dia pipe linecomplete all as specified and directed by Engr-in-Charge. |
| 114 | All as per serilaitem No 106.00 here-in-before but of size 20mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 115 | All as per serilaitem No 106.00 here-in-before but of size 15mm dia pipe line complete all as specified and directed by Engr-in-Charge. |
| 116 | M& L for complete dewatering and cleaning of overhead MS tank of capacity 20 KL gallons with high pressure jet to remove all masses ,algae and dirt and removal of dirty water along with sludge using sludge machine and disposal of same to a safe distance and including scrubbing of internal surface using industrial vacuum machine and applying of anti-bacterial sterilization spray and apply one coat food grade paint to wall , floor and ceiling , internal surface of reservoir where applicable complete all as specified and directed by Engr-in-Charge. |
| 117 | Taking down carefully old GI pipe of of size 15 mm bore and setting aside for reuse if found serviceable complete all as specified and directed by Engr-in-Charge. |
| 118 | All as per serial item No 112.00 here-in-before but of size 20 mm bore complete all as specified and directed by Engr-in-Charge. |
| 119 | All as per serial item No 112.00 here-in-before but of size 25 mm bore complete all as specified and directed by Engr-in-Charge. |
| 120 | All as per serial item No 112.00 here-in-before but of size 40 mm bore complete all as specified and directed by Engr-in-Charge. |
| 121 | All as per serial item No 112.00 here-in-before but of size 50 mm bore complete all as specified and directed by Engr-in-Charge. |
| 122 | All as per serial item No 112.00 here-in-before but of size 80 mm bore complete all as specified and directed by Engr-in-Charge. |
| 123 | Refixing old steel tubing and connections in new or old position (walls, ceiling , floors, etc) of size 20 mm bore complete all as specified and directed by Engr-in-Charge. |
| 124 | All as per serial item No 118.00 here-in-before but of size 25 mm bore complete all as specified and directed by Engr-in-Charge. |
| 125 | All as per serial item No 118.00 here-in-before but of size 40 mm bore complete all as specified and directed by Engr-in-Charge. |
| 126 | All as per serial item No 118.00 here-in-before but of size 50 mm bore complete all as specified and directed by Engr-in-Charge. |
| 127 | All as per serial item No 118.00 here-in-before but of size 80 mm bore complete all as specified and directed by Engr-in-Charge. |
| 128 | Supply laying, testingGI tubing15 mm dia bore medium grade conforming to IS : 1239with all fittings laid in trenchescomplete all as specified and directed by Engr-in-Charge. |
| 129 | All as per serial item No 123.00 here-in-before but of size 20 mm bore complete all as specified and directed by Engr-in-Charge. |
| 130 | All as per serial item No 123.00 here-in-before but of size 25 mm bore complete all as specified and directed by Engr-in-Charge. |
| 131 | All as per serial item No 123.00 here-in-before but of size 80 mm bore complete all as specified and directed by Engr-in-Charge. |
| 132 | All as per serial item No 123.00 here-in-before but of size 50 mm bore complete all as specified and directed by Engr-in-Charge. |
| 133 | All as per serial item No 123.00 here-in-before but of size 40 mm bore complete all as specified and directed by Engr-in-Charge. |
| 134 | M&L for prepration of surface of water pipe line above the ground level for Panting with two coat of weather proof, synthetic enamaled paint over one cote of primer complete all as specified & directed by Engr-in-Charge. |
| 135 | Carry out Servicing from authorised rep or service engineer of the manufacturer of Industrial R.O+U.V. Water purifier system consisting of Fiber Reinforced Polymer Vessel with treatment media like FBM, AFM, MGS, ACM, CPM, etc of capacity 1000 LPH,completeall as specified and directed by Engr-in-Charge. |
| 136 | Attending Complaints for rectification of fault in RO i panel (contorl Panel) of Industrial R.O+U.V. Water purifier system consisting of Fiber Reinforced Polymer Vessel with treatment media like FBM, AFM, MGS, ACM, CPM, etc of capacity 1000 LPH including replacement of worn out relay, cable, fuse,diode etc complete all as specified and directed by Engr-in-Charge. |
| 137 | Supply, fixing & testing in replacement GSM based RO i panel (contorl Panel) of Industrial R.O+U.V. Water purifier system consisting of Fiber Reinforced Polymer Vessel with treatment media of capacity 1000 LPH complete all as specified and as directed. Make:Renuka water Tecnology or equvalant in Havells, L&T Note : Model should be compatable for existing RO plant. |
| 138 | Supply and fix and testing food grade Activated carbon for RO plant of capacity 1000 LPH complete all as specified anddirected by Engr-in-Charge. |
| 139 | Supply and fix and testing food grade softner Resin 220 Na for RO plant of capacity 1000 LPH complete all as specified and directed by Engr-in-Charge. |
| 140 | Supply and fix and testing 20\" Jumbo Span Candel for RO plant of capacity 1000 LPH complete all as specified anddirected by Engr-in-Charge.Note : Model should be compatable for existing RO plant. |
| 141 | Supply and fix and testing RO Membren 40 x 40 for RO plant of capacity 1000 LPH complete all as specified and as directed.Note : Model should be compatable for existing RO plant. |
| 142 | Supply and filling clean wash sand for RO plant of capacity 1000 LPH complete all as specified and directed by Engr-in-Charge. |
| 143 | Supply and filling (NaCl) (Common Salt)for RO plant of capacity 1000 LPH complete all as specified and directed by Engr-in-Charge. |
