Tender For Construction Of Police Station Building At Lakhanpura In District Bharatpur
Tender Value
3.18 Crore
Estimated cost
Bid Submission
28 Jun 2023
0 days left
EMD
6.36 Lakhs
Bank guarantee accepted
Document Fee
5900
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
bharatpur → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Police Station Building At Lakhanpura In District Bharatpur
BOQ
| Sl. No. | Item Description |
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal ofexcavated earth, lead upto 50m andlift upto 1.5 m , disposed earth to be levelled and neatly dressed:All kinds of soil Footing grid 1 and 2,Vertical |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. |
| 4 | Carriage of earth, sand, lime, morrum, mannure or salb etc. including loading, unloading & staking as per specification etc. complete with lead of 5 Km. |
| 5 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level:-M10 grade Nominal Mix 1: 4: 8 (1 cement : 4 coarse sand : 8 graded stoneaggregate 40mm nominal size). |
| 6 | Providing and laying in position specified grade ofcement concrete forall RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix |
| 7 | Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in:Cement Mortar 1:6 ( 1-Cement : 6-Sand). |
| 8 | Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.M20 grade Nominal Mix / Design Mix |
| 9 | Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix |
| 10 | Providing M-25 grade concrete by usingcement as per codal provision instead ofM-20 grade design mix. |
| 11 | Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. |
| 12 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : -- Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. |
| 13 | Columns, pillars, posts and struts etc. |
| 14 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. (\"Original producers\" who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786) :-Thermo-mechanically Treated bars (Conforming of relevent IS code) |
| 15 | Providing, hoisting and fixing up to floor five level precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6mmnominal size) reinforced with 1.6 mm dia Mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1 : 3 (1 cement : 3 fine sand ) etc complete as per approved design excluding plastering of jambs, sills and soffits :-50mm thick |
| 16 | Providing and fixing Stone jali 40mm thick Red/Pink sand stone throughoutin cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade, jali patterns to be cut square to jali slab without any chamfers etc: |
| 17 | Brick work with mechanised autoclaved flyash lime bricks conforming to IS: 12894 :2002 of class designation 100 in superstructure above plinth level upto floor V level in.Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 18 | Half Brick work with mechanised autoclaved flyash lime bricks conforming to IS: 12894 :2002 of class designation 100 in superstructure above plinth level upto floor V level in.Cement mortar 1 : 4 (1 cement : 4coarse sand) |
| 19 | Add extra providingand placing in position 2 Nos. ,6mm Ø M.S. barat every thirdcourse of half brick masonry . |
| 20 | Supplying and fixing in walls machine cut and polished stone shelves, tands andin CM 1:3 with machine cut edges :Sand or other approved stone 50mm thick. |
| 21 | Kota stone minimum 30mm thick. |
| 22 | Providing and laying damp-proof course with cement concrete gradeM-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proofcompound complete as per specification .75mm thick |
| 23 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 24 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirmingto IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). |
| 25 | ExtraforusingMarbleprinted/Graniteshadeordarkshadetilesinsteadofwhite,grey,ivory,fumeredbrown,lightgreen,lightblueandotherlightshadesinglazedtilesandMATfinishedtiles. |
| 26 | Extraforusingsize above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finishedtiles in place of 300mm x 300mm size. |
| 27 | P & F 1st quality Heavy Duty Vitrified Double Charged tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete.:-size600 mm X 600mm |
| 28 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide |
| 29 | Supply and fixing in cement mortar welded hand railing made out of MS round or square bars, flats etc. for staircase or verandah as per design complete in all respect (wooden or PVC hand railing to be paid extra) with priming coat of red oxide. |
| 30 | Extrafor providing D type pipe head as top of hand railing |
| 31 | Grading roof for water proofing treatment withwater proffing compound:-Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 32 | Crazy marble stone flooring 20mm thick marble stone with black or of specified colour topping including filling the gaps with cement marble chips mixin proportion of 4 : 7 (4cement: 7 white black or white or black marble chips) size from 1mm to 4mm by volume and under layer of 25mm thick cement concrete [1:2:4, graded stone aggregate 12.5mm nominal size] rubbing and polishing and cement slurry etc. complete :In ordinary cement. |
| 33 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : |
| 34 | Making khurras 450 x 450mm with average minimum thickness 50mmcement concrete 1 : 2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1 : 3 and onecoat of neat cement, rounding edges and making and finishing the out let complete. |
| 35 | Cement concrete flooring grade 1:2:4 (1-Cement:2-Coarse sand:4-graded stone aggregate) rounding off edges etc. but excluding the cost of nosing of steps etc. complete :( Used Banas / Bikaner sand ) :- 75 mm thick with 20 mm thick nominal size aggregate. |
| 36 | Kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :- For area of each slab from 2001 to 5000 Sq.Cm |
| 37 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete :-For area of each slab from 2001to 5000 Sqcm |
| 38 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 39 | Extra for Mirror polishing on terrazzo/Kota stone work where ever required to give high gloss finish complete. |
| 40 | Fine grinded Gangsaw cut 30-35 mm thickstone flooring over 20 mm (average) thick base of cement mortar 1:4 (1 cement :4 coarse sand) jointed grey cement slurry mixed with pigment to match the shade of stone complete as per design drawing and instruction of EI.:- Red sand stone (Karauli stone) |
| 41 | Random rubble dry stone Kharanja under floor. |
| 42 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 25 mm thick |
| 43 | Rough cast plaster upto 10m height above ground level with a mixture of sandand gravel or crushed stone from 6mm to 10mm nominal size dashed over and including the fresh plaster in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. Ordinary cement finish using ordinary cement |
| 44 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20 mm thick |
| 45 | Plaster on new surface on walls in cement sand mortar 1:6 including raking of joints etc. complete fine finish 12 mm thick. |
| 46 | 6mm cement plaster to ceiling of mix 1:3 (1 Cement : 3 fine sand) |
| 47 | Making grooves as per design in plaster 10mm to 20mm wide. |
| 48 | Making of drip course (Tapka) in cement sand mortar 1:6 width upto 40 mmand 10 mm thick as per approved design |
| 49 | 12 mm thick plain cement mortar bands in cement mortar 1:4 (1 cement : 4 fine sand) :Raised Band 75 mm wide |
| 50 | Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete:- New Plastered Surface (three or more coats) |
| 51 | Finishing walls with Acrylic Smooth exterior paint of requiredshade including all scaffolding.New work (Two or more coat applied @ 1.67 ltr/10 sqm overand including base coat of water proofing cement paint applied@ 2.20 kg/ 10 sqm ). |
| 52 | Painting exterior surface ofWallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect including scaffolding and safety provision:- New Work |
| 53 | Finishing walls with textured exterior paint of required shade as per approved colour complete as per manufacturers specificationsincluding primer coat and protecting coat including scaffolding and safety provision :- Roller Finish av. thickness 400 to 500 microns. |
| 54 | Painting with synthetic enamel paint of approved brand and manufacture togive an even shade : Two or more coats on new work |
| 55 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proffing cement compound @0.253 kg//sqm .This layer will be allowed to air cure for 4 hours.b) Second layer of slurryof cement @ 0.242 kg/sqm mixed with water proffing cement compound @ 0.126 kg/sqm This layer will be allowed to air cure for4 hours followed by water curing for 48 hours.The rates includes preparation of surface treatment & sealing of all joints ,corners,junction with polymer mixed slurry. |
| 56 | Providing and Placing in position suitable PVC water stops conforming to IS:12200for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete : Serrated with central bulb (225 mm wide, 8-11 mm wide) |
| 57 | Providing and fixing expansion joint board for building RCC column beams, walls, slab of Polyethylene foam of density 30 to 35 Kg/m3 of Armour Board. :- 40 mm Thick |
| 58 | Providing and fixing 150 mm wide sheet covering over expansion joints with iron screws as per design to match the colour / shadeofwall treatment. :- Aluminum fluted strips 2 mm thick |
| 59 | Filling of sunk portion of roof with earthen pots of required height including filling voids with 1:3:6 light concrete, using brick batscomplete levelling and dressing the surface by 50mm thick cement concrete 1:2:4 as per specification. |
| 60 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.:- Good quality Green/Black:- Above 3601 Cm2 Slabs |
| 61 | Extra for providing edge moulding to 15-18mm thick marble/ Granite/Kota stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite/Kota Stone Work |
| 62 | Half Edge moulding |
| 63 | Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone workincluding necessaryholesfor pillar taps etc. including rubbing and polishing of cut edges etc. complete |
| 64 | Providing non slip grooves to granite/ kota stone flooring, counters, vanities etc. using groove cutter V type including machine polishing to groove to give high gloss finish etc. complete as per design approved by engineer in charge Entrance steps |
| 65 | Steel work in built up tubular trusses including cutting, hoisting ( height upto 10 m)fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete.Hot finished seamless type tubes. |
| 66 | Renewing glass panes, with putty and nails wherever necessary:plain glass panes of thickness 5 mm |
| 67 | Supply and fixing of Modular work Station with Partition 32mm thick Aluminum top 25 mm thick particale board with post formed legas 18mm particle board with four side edage banding one KBT or one CPU trolley. Size 2100 x 2100 x 1200mm single seat in combination |
| 68 | Supply and fixing of Modular work Station with Partition 60mm thick Aluminum top 25mm thick particale board with post formed one drawer or one open able shutter one KBT or one CPU trolley Two 1200mm height storage unit. Size 1200 x 1200 x 1200mm single seat in combination |
| 69 | Providing and Fixing Chiken wire mesh at the joint of masonry members/ R.C.C. Memberswith Nails complete in all respect. |
| 70 | Supply and installation of Multi Rib Proofing/cladding Sheet Manufacture out of0.50mm TCT (Total Coated Thickness) high tensile Zinc aluminum alloy coated galvaiumeseel (as per 150gsm zinc aluminum coated 550Mpa tuekd strength) confirming to IS: 1397/astm A-792 sheet to have wide pens 30mm high NB at 250 centre and centre width of 1020mm shets be casted with regular modified plyster system on a continuous with line on centre for face and with a polyster coating respectively sheet shall have proportionality with siphoned plate at made at to prevent leakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. The sheet shall be supplied in cost one length and foe a minimum up to 12mts with all scaffolding.:-Add extra for 0.80mm TCT (Total Coated Thickness) high tensile Zinc aluminum alloy coated galvaiumeseel sheet in place of 0.50mm thick |
| 71 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 72 | Supply and Installation of WALL – PREFABRICATED INSULATED PPGL PANEL: |
| 73 | Walls: Insulated sandwich panels for wall of total thickness mentioned below. Panel shall have 0.50mm (+/-0.04mm) thick pre coated metal sheet on both sides of rigid PUR insulation. The pre-coated metal sheet shall be PPGL (Pre Painted Galvalume Sheet with AZ coating) sheet having SDP (Super Durable Polyester) colour coat of 18 micron (min). The panels shall be vertically joined together with adjacent panel by tongue and groove joints. For joining, wall panel\"s metal sheet facings must have lengthwise flange (U shape) of 8mm x 8mm on groove side and 8mmx12mm on tongue side of panel. The pre-coated metal sheet (PPGL) must also be pre-strengthened by full lengthwise stiffening with semi-circular beading of 12mm width & 3 to 4mm depth at 240 (+/-5) mm pitch. Panels may have optional provision for inbuilt electrical conduit running lengthwise atvertical center of specified panels. The insulation core shall be self-extinguishing DIN 4102,Class B3 fire retardant class rigid PUR with thermal conductivity of 0.025 W/mK and with density of 40kg/m3 (+/-2kg) suitable for temperature range of -30 degree C to +80 degree C. The panel must be made using glue-free high pressure pressing self-bonding method. PPGL sheet on both sides of panel shall have a min15 micron protective plastic guard film to avoid scratches during transportation.:_ Thickness 55mm (+/- 2mm) |
| 74 | AccessoriesSupply and Installation of (Labour rate included in main item) :- Bottom and Top U track :U-track for mounting panels with floor. The channel shall be made from minimum 1.15 mm thick PPGL sheet with flange height of minimum 35 mm and width as per thickness of panel used. |
| 75 | Flashings (inner and outer): Corner angle flashings of equal shape for covering various corners and open sides of panels. Flashings shall be made from 0.5mm thick pre-coated PPGL sheet in following sizes: 50mm x 50mm |
| 76 | Providing and fixingaluminum workfor doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285,fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and thedirections of Engineer- in – charge .(Glazing and paneling to be paid for separately). :-For fixed portion ,Powder coating aluminum(minimum thickness of powder coating 50 micron) FF IO Work station Door frame |
| 77 | For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). :-Powder coating aluminum( minimum thickness of powder coating 50 micron) FF IO Work station |
| 78 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board Grade I, Type II conforming to IS : 12823 bonded formaldehyde synthetic resin ,of approved brand and manufacture in paneling fixed in aluminium doors ,windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. :- Prelaminated particle board with decorative lamination on both sides. |
| 79 | Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basicitem.) :- With float glass panes of 8 mm thickness |
| 80 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. :- With stainless steel cover plate |
| 81 | Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 82 | Providing and fixing aluminium U shape handle of size 100mm with SS screws etc. Complete as per direction of Engineer-in-charge:- Powder coated minimum thickness 50 micron aluminium |
| 83 | Providing and fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm x 6.0mm and opening of size 102mm x 99mm to aluminum window/vent with required screws, Y and H aluminium sec (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge :-Powder coating aluminum( minimum thickness of powder coating 50 micron). |
| 84 | S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by Aluminium beading 20x3mm with suitable screws at not exceeding 150mm distance at all heights with all lead and lift with scafolding. Front |
| 85 | Filling the gap upto 5 mm depth and 5 mm width in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. |
| 86 | Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. |
| 87 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure \"A\": 35 mm thick,Commercial Veneer both side |
| 88 | Extra for cutting rebate in flush door shutters for making double leaf shutter(Total area ofthe shutter to be measured). |
| 89 | Extra for providing other type of fittings as mention in annexure A ( as approved by EI) :Stainless steel fittings |
| 90 | Extra for cutting rebate in flush door shutters for making double leaf shutter(Total area ofthe shutter to be measured). |
| 91 | Providing and fixing S.S. Rod 30mm dia (304 grade ,16SWG) includingbrackets fixed with C.P. brass screws and rawl plugs, etc., wherever necessary complete two side central all fittings. |
| 92 | Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitred weldedand grinded including hold fast of steel lugs 13mm x 3mm and 15 Cm long embedded in C Cblock 15 x 10 x 10 Cm of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred and grinded including 10mm x 10mm square bars welded to framefor paitam fixing float glass 4mm thickpanes with glazing clips and metal sash putty andfixing of shutters frames peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of Engineer-in –charge :- Window openable. |
| 93 | Window fixed. |
| 94 | Extra for additional shutter in pipe section windows with wire gauge 14 mesh x 24 gauge |
| 95 | Providing and fixing Square bars or other flat welded to window, ventilatiors etc. |
| 96 | Providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size. :- Welded mesh 25 mmx 25 mm x 2.1 mm Balcony |
| 97 | Providing and fixing of double leaf steel shutterfor cupboard, the frame is made of pressed steelISI section 80x25 mmx1.25 mm thickwith 1.00 mm MS sheet to spot welded including holdfasts of 15x3mm, MS oxidized fittings such as butt hinges, sliding doors bolts, handles, tower bolts and twin peg etc completeincluding applying priming coat of approved steel primer of red oxide zinc chromate andspray painting in approved shade with decopaint of approved quality complete as per direction of Engineer In Charge |
| 98 | Providing and fixing cow catcher made of R.S. joist angles channels MS rounds including cutting welding and fabrication with priming coat of red oxide (as per design). |
| 99 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 100 | Providing and fixing M.S. sheet 1mm thicksingle leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint |
| 101 | Providing and fixing in position collapsible steel shutters with vertical M.S. Channels 20 x 10 x 2mm and bracket with flat iron diagonals 20 x 5mm. size with top and bottom rail of T-iron 40 x 40 x 6mm. with 40mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured and paid as per outer dimension). |
| 102 | Providing and fixing 25 mm thick Non slippery reflective type designer paving tile with metallic hardening using 2 Kg/sq.mtr made out of cement concrete of required grade, sizes of tile upto 300X300 mm Manufactured with wet cast Vibration system in two layers and laid over base of 20 mm thick cement morter1:4 using neat cement slurry in cluding finishing of joints etc. complete. :-Using M-30 grade cement Concrete |
| 103 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant.:- 110 mm dia |
| 104 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: |
| 105 | Bend 87.5 |
| 106 | Door tee |
| 107 | Pipe Clip |
| 108 | M-50 100mm thick to be used in heavy-traffic ( Heavy traffic is defined as a daily traffic of 450-1500 commercial vehicles exceeding 30 KN laden weight, or an equivalent of 2.0 to 5.0 MSA for a design life of 20 years.) like Bus terminals, industrial complexes, mandi houses roads on expansive soils, factory floor , service station, industrial pavements.etc. :- Category‘B’ Denated only two side like I,Z,T shape etc. as per IRC SP63:2004 |
| 109 | P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor Size 580x440mm. |
| 110 | P & F European type white glazed vitreous china 1st quality Double syphonic W.C (IS :2556 Mark) with P or S trap including cutting and making good the wall and floor |
| 111 | P & F Premium quality water closet Seat Covers with brass hinges complete Solid PVC (ISI marked) grade-I White for EWC. |
| 112 | P & F Low level Flushing Cistern of 10 litres capacity (IS :2556 mark) of approved make with complete fittings C.I.brackets duly painted, brass ball cock with ball (IS: 1703mark) complete including cutting and making good the wall: WVC with C.P. brass bend |
| 113 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall : Size 550 mm x 400 mm dia for counter top |
| 114 | P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete.Flat Back (large) or half stall size 610x400x80mmFlat Back (large) or half stall size 610x400x80mm. |
| 115 | P&FC.P.brassUrinalFlushPipeset complete with flanged brackets of approved make. For 4 Urinals |
| 116 | For 1 Urinal |
| 117 | P & F C.P. brass Urinal Spreader for stall urinal of approved make. |
| 118 | P & F Bottle Trap of approved make :C.P Brass 40 mm |
| 119 | P & F Towel Rail or Ring of approved quality/make: |
| 120 | C.P. brass Towel Rail elbow type with concealed screws size 600 mm (Heavy duty).C.P. Brass Towel Ring revolving type |
| 121 | P & F Tooth Paste & Brush Holder of approved quality/make: Stainless Steel |
| 122 | P & F Shower arm 15mm dia of approved quality/make. (-do-) size 370mm.(-do-) |
| 123 | P & F Bath Shower of approved quality/make.C.P. brass of Heavy & superior quality, revolving with adjustable key 150mm. |
| 124 | P & F Extension Pipe for bib cocks of approved quality/make.(-do-) 150 X 15mm. |
| 125 | P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. |
| 126 | Providing & fixing C.P.flange for 15mm dia taps. |
| 127 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make:C.P. Brass bib cock,15mm nominal bore. |
| 128 | (-do-) Long body, 15mm nominal bore weight not less than 690 gm |
| 129 | P & F Stop Cock(IS :8931 Mark),superior quality & ofapproved make: (-do-) Concealed stop cock 15mm |
| 130 | P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc.---do--- with 37 cm long pipe and nut. |
| 131 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 160 mm dia110 mm dia |
| 132 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: |
| 133 | Bend 87 .5 110 mm dia |
| 134 | Coupler (socket) 110 mm dia |
| 135 | Pipe Clip 110 mm dia |
| 136 | Plain Tee110 mm dia |
| 137 | Plain floor trap 110mm dia |
| 138 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 75 mm dia |
| 139 | 110mm dia |
| 140 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make |
| 141 | Coupler 75mm dia |
| 142 | Coupler 110mm dia |
| 143 | Bend 87.5 Dg. 75mm dia |
| 144 | Bend 87.5 Dg.110mm dia |
| 145 | Single \"Y\" with Door 75mm dia |
| 146 | Single \"Y\" with Door 110mm dia |
| 147 | Door Bend 87.5 Dg. 110mm dia |
| 148 | Single Tee 75mm dia |
| 149 | Single Tee 110mm dia |
| 150 | Single Tee with Door 75mm dia |
| 151 | Single Tee with Door 110mm dia |
| 152 | Nahni Trap without Jali 4” 110mm dia |
| 153 | Vent Cowel110 mm dia |
| 154 | Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead.Depth up to 0.5 M |
| 155 | Add extra over item 3.19.1 for every additional 0.10m depth above 0.5 m depth. |
| 156 | Construction of chamber in all type of soil with 300 mm thickmasonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation,20mm thick insider plaster in Cm 1:6, finished with floatingneat cement, 50mm thick M-15 grade C.C. flooring ,earthwork etc. complete as per design including disposal ofsurplus earth within a lead of 50 mtr. Inside size 300 X 300 mm depth upto 0.5 M Cement coverwith frame |
| 157 | do- size 450 x 450mm depth upto 0.5 M Cement cover withframe |
| 158 | P & F G.I. Pipes (External Work) with G.I. fittings excluding union (IS : 1239 Mark) including trenching & refilling earth etc. 32mm dia nominal bore \"B\" Class |
| 159 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes (IS 15778 : 2007 code) having thermal stability for hot& cold water supply including all CPVC plain & brassthreaded fittings i/c fixing the pipe with clamps at 1 metrespacing. This includes jointing of pipes & fittings with onestep CPVC solvent cement and testing of joints complete asper direction of Engineer in Charge. (Internal work Exposedon wall) Exposed on wall 20mm nominal size \"B\" Class |
| 160 | 32mm nominal size\"B\" Class |
| 161 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes (IS 15778 : 2007 code) having thermal stability for hot& cold water supply including all CPVC plain & brassthreaded fittings i/c fixing the pipe with clamps at 1.00 mspacing. This includes jointing of pipes & fittings with onestep CPVC solvent cement and the cost of cutting chases andmaking good the same including testing of joints complete asper direction of Engineer in Charge. (Concealed workincluding cutting chases and making good the walls etc.,) 25 mm nominalsize\"B\" Class |
| 162 | Construction of Cement Concrete Chamber 125mm dia. C.P. Brass grating |
| 163 | Construction of Cement Concrete Chamber 125mm dia on depressed floor upto 45cm height from floor with : C.P. Brass grating |
| 164 | Providing Laying & jointing glazed S.W. pipes grade `A` (IS;651 marked) of approved make with spun yarn & stiff mixture of cement mortar 1:1, excavation & refilling of earth in all types of soil upto 1.2m depth, S.W. fittings, including testing of joints etc, complete.100mm dia |
| 165 | 150mm dia |
| 166 | Providing & Laying C.C. 1:5:10 (Stone aggregate 40mm nominal size) all around S.W. pipe including 15 Cm. thick bed concrete (Width W= Diameter of pipe in Cm+30 Cm.)( Excluding cost of pipe)100mm dia |
| 167 | 150mm dia |
| 168 | Making of holein R.C.C. slab/wall/beams and masonary wall (width up to 450 mm) by core cutting machine complete as per direction of EI Fromdiameter 100mm to 150mm |
| 169 | Supply & fixing G.I. Union ISI marked in G.I. pipe line as required complete in all respect of size :15mm dia nominal bore |
| 170 | 20mm dia nominal bore |
| 171 | 32mm dia nominal bore |
| 172 | Construction of septic Tank in all types of soil with 40 Cm.thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C floor & RCC slab covering with M15 grade c.c.floor, 50 mm thick stone slab partition walls, 20 mm thickplaster in CM 1:6 finished with neat floating cement, 4 Nosstone foot rests of approved design ,two No. 450 mm dia eachFerro cement cover with frame, earth work etc. complete asper approved drawing including disposal of surplus earthwithin a lead of 50 mtr:- Size 200x100x130 cm.(for 10 users) with 115 mm thick RCC(M-20) slab with Tor steel reinforcement 8mm ? @15 cm c/cbothways including shuttering complete in all respect. |
| 173 | Size 230 x110 x150 cm.(for 20 users) with 115 mm thickRCC (M-20) slab with Tor steel reinforcement 10mm ? @15cm c/c bothways including shuttering complete in all respect. |
| 174 | Size 400 x140x150 cm.(for 50 users) with 115 mm thick RCC(M-20) slab with Tor steel reinforcement 10mm ? @15 cm c/cbothways including shuttering complete in all respect. |
| 175 | Construction of soakage well in all type of soil with 300 mmthick dry masonry, top and bottom 300 mm course in CM 1:6,80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal,Kharanja, 40 mm thick M-15 grade C.C flooring , earthworkcomplete as per approved drawing including disposal of earthwithin a lead of 50 mtr.:Size 300 Cm. dia outside & 300 Cm. depth |
| 176 | Size 240 Cm. dia outside & 240 Cm. depth. |
| 177 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : Gun-metal 15mm nominal bore. |
| 178 | (-do-) 25mm nominal bore. |
| 179 | (-do-) 32mm nominal bore. |
| 180 | P & F Ball Cock (IS :1703 Mark) with Rod& P.V.C. Ball complete : Brass wt. Not less than 300 gm,15mm. |
| 181 | Surface dressing of the ground including removing vegetationand inequalities not exceeding 15cm deep and disposal ofrubbish lead up to 50 Mtr. and lift up to 1.5 Mtr. : All kinds ofsoil |
| 182 | Earth work in excavation by mechanical means (HydraulicExcavator )/ manual means in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) includingdressing of sides and ramming of bottoms, lift upto 1.5 m,including taking out the excavated soil and depositing andrefilling of jhiri with watering & ramming and disposal ofsurplus excavated soil as directed with in a lead of 50 meter.All kinds of soil |
| 183 | Supplying and Filling in plinth with river sand under floorsincluding watering ramming consolidating and dressingcomplete including cost of sand |
| 184 | Providing and laying in position cement concrete includingcuring, compaction etc. complete in specified grade excludingthe cost of centering and shuttering - All work up to plinthlevel1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size). |
| 185 | Random Rubble stone masonry for with hard stone infoundation and plinth in Cement Sand mortar above 30 CMthick wall in: Cement Mortar 1:6 ( 1-Cement : 6-Sand) |
| 186 | Brick work with F.P.S. bricks of class designation 75 insuperstructure above plinth level upto floor V level in allshapes and sizes in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 187 | Providing and laying damp-proof course with cement concrete gradeM-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proofcompound complete as per specificat75mm thick. |
| 188 | Providing & fixing precast cement concrete coping 1 : 2: 4 mix 50mm thick complete as per specification : |
| 189 | Plaster on new surface on walls in cement sand mortar 1:6including racking of joint etc. complete fine finish : 20mm thick |
| 190 | Painting exterior surface of Wall with 100% acrylic exteriorpaint of approved brand and manufacture to give an evenshade with two or more coats including prepartion of basewith sand papering, primer, putty, etc complete in all respectincluding scaffolding and safety provision New Work |
| 191 | Providing and fixing concertina coil fencing with required dia610 mm (having 15 nos. round per 6 metre length) up to 3mheight of wall with existing angle iron \"Y\" shaped placed 2.4 mor 3.00 m apart and with 9 horizontal R.B.T. stud tied with GIstaples and GI clips to retain horizontal including necessarybolts or GI barbed wire tied to angle iron all complete as perdirection of Engineer In Charge with reinforced barbed tape(R.B.T.)/Spring core(2.5 mm thick) wire of high tensilestrength of 165 kg/sq.mm with tape (0.52 mm thick) andweight 43.478 gm/metre (Cost of MS angle, CC block shall bepaid extra) |
| 192 | Providing and fixing steel gate, grating , and grills made ofangles, tees, square bars, flats,or black pipe with holdfast andfittings complete as per design and drawing including cuttingwelding and fabrication with priming coat of red oxide Boundrywall gate |
| 193 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds o f soilsOUTER DEVELOPMENT PARKING |
| 194 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). PCC Footing OUTER DEVELOPMENT INTERNAL ROAD PARKING |
| 195 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. PARKING |
| 196 | Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. M15 grade Nominal Mix. 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size). |
| 197 | Structural steel work in single section fixed with or without connecting plate including cutting, hoisting ( height upto 10 m), fixing in position and applying a priming coat of approved steel primer all complete.PARKING |
| 198 | Steel work in built up tubular trusses including cutting, hoisting ( height upto 10 m)fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete. Hot finished seamless type tubes. |
| 199 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxideOUTER DEVELOPMENT |
| 200 | Supply and installation of Multi Rib Proofing/cladding Sheet Manufactureout of 0.50mm TCT (Total Coated Thickness) high tensile Zinc aluminumalloy coated galvalume steel (as per 150gsm zinc aluminum coated 550Mpatuekd strength) confirming to IS: 1397/astm A-792 sheet to have wide pens30mm high NB at 250 centre and centre width of 1020mm sheets be castedwith regular modified polyster system on a continuous with line on centrefor face and with a polyster coating respectively sheet shall haveproportionality with siphoned plate made to prevent leakage sheet shall befixed by more of sell drilling lift tapping hot dip zinc coated hox headfasterner of size 12x14x55mm long. The sheet shall be supplied in cost onelength and for a minimum up to 12mts with all scaffolding. |
| 201 | Finishing walls with Acrylic Smooth exterior paint of requiredshade including all scaffolding.New work (Two or more coat applied @ 1.67 ltr/10 sqm overand including base coat of water proofing cement paint applied@ 2.20 kg/ 10 sqm ). New work (Tw o or more coats applied @ 3.84 kg/10 sqm). OUTER DEVELOPMENT |
| 202 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. OUTER DEVELOPMENT |
| 203 | Painting with synthetic enamel paint of approved brand and manufacture togive an even shadeTwo or more coats on new work:PARKING |
| 204 | Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in:Cement Mortar 1:6 ( 1-Cement : 6-Sand). OUTER DEVELOPMENT |
| 205 | Random Rubble stone masonry with hard stone in superstructure aboveplinth level and upto five levelabove 30cm. thick walls in : Cement Mortar 1:6 ( 1-Cement : 6-Sand). OUTER DEVELOPMENT |
| 206 | M-40 80mm thick to be used in heavy-traffic ( Heavy traffic is defined as a daily traffic of 450-1500 commercial vehicles exceeding 30 KN laden weight, or an equivalent of 2.0 to 5.0 MSA for a design life of 20 years.) like Bus terminals, industrial complexes, mandi houses roads on expansive soils, factory floor , service station, industrial pavements.etc. :- Category‘B’ Denated only two side like I,Z,T shape etc. as per IRC SP63:2004 |
| 207 | Construction oftubewell up to 100m depth and above to accomodate housing and assembly pipe in all types of alluvium strata by rotay drilling method with \"code of practice for construction and testing of tubewells (IS:2800 (Part-II) : 1991 and IS:2800 (Part-II) :1979 both amended up to date) with supply of bail plug if necessary.The work will not include cost of housing pipe and strainer pipe assembly cost, gravel and development work. Work would be deemedcompleted only after obtaining sound free water during pumping. 200 mm nominal bore |
| 208 | Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size of slotting as per IS:8110-1985. |
| 209 | 200mm-do-. |
| 210 | Construction of Recharge Shaft in filter pit including Earth work Excavation , lifting excavted earth with all lift and 50 m lead and centering & shuttering evenever required.Diameter 900 mm |
| 211 | Supply & fixing Pre-cast RCC Rinngs at the mouth of recharge shaft of M20 mix with40 mm thickness Diameter 900 mm |
| 212 | Supply & lowering air line of 25mm dia, G.I. pipe \"B\" class having perforation 3 to 5mm size all arrow of G.I. pipe in Zig-Zag fashion & making air vent at top including the cost of Tee-Nipples, Elbow, Socket etc. |
| 213 | Supply and lowering vent air pipe 63mm dia rigid PVC pipe(IS 4985) mark class II (4kg per cm2 ) with required all necessary fittings including perforation of 3 to 5 mm size all around the pipe at a distance of 180 to 220mm in zig zag fashion and making air vent at top complete as per direction of Engineer incharge. |
| 214 | Supply & lying River-gravels of following sizes in recharge shaft, filter pit after screening & washing from kachha shift without deduction of voids |
| 215 | Size 9 to 12 mm |
| 216 | Size 3 to 5 mm |
| 217 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. |
| 218 | 160 mm dia |
| 219 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: |
| 220 | Coupler (socket) |
| 221 | 160 mm dia |
| 222 | Plain Tee |
| 223 | 160 mm dia |
| 224 | Bend 87 .5 |
| 225 | 160 mm dia |
| 226 | Supply & laying of clean, clear sharp river sand of size 1 to 2mm coarse, without deduction of voids. |
| 227 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copperconductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulatedunsheathed flexible copper earth conductor 1.1 kV grade (IS:694) inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit &it\"s ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick HotDipped Galvanized Modular Box with earth terminal, 10A Modularswitch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3way connector, screws, making connections, testing etc. as required.For specification of copper Conductor, Phenolic Laminated sheet\"s &Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 Foradditional technical parameters of product / work refer Annexure \"A\"attached with this BSR |
| 228 | Short point (up to 3 mtr.) |
| 229 | Medium point (up to 6 mtr.) |
| 230 | Long point (up to 10 mtr.) |
| 231 | Wiring of twin control light point with 1.5 sq. mm nominal size FR PVCinsulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq.mm nominal size FR PVC insulated unsheathed flexible copper earthconductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P- III ) PVC conduit & it\"s ISI marked (IS:3419-1988) accessories, roundtiles, 2 Nos Hot Dipped Galvanized M.S Modular box of 1.2 mm thickwith earth terminal,2 Nos10 A two way Modular switch, 3 pin ceilingrose / holder / 3 way connector ,Modular face plate with grid plate,screws, making connections, testing etc. as required. For specificationof copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiringaccessories refer Chapter E - 04, E - 05 & E - 07 For additional technicalparameters of product / work refer Annexure \"A\" attached with this BSR |
| 232 | Medium point (up to 6 mtr.) |
| 233 | Long point (up to 10 mtr.) |
| 234 | Description Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it\"s ISI marked (IS:3419- 1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal, 10 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter E - 04, E- 05 & E - 07 For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR |
| 235 | On board |
| 236 | Medium point (up to 6 mtr.) |
| 237 | Long point (up to 10 mtr..) |
| 238 | Supplying and fixing of power plug point with Modular accessories as perPWD specification for electrical Works, on hot dipped galvanized modularbox of 1.2 mm thick with earthing terminal/connector on surface or inrecessed with suitable size of modular face place with grid plate and coverplate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. asrequired. For specification of Wiring accessories refer Chapter E - 07related item & For additional technical parameters of product / work referAnnexure \"A\" attached with this BSR |
| 239 | Providing & Fixing of IP20, 2\"x2\" LED Surface/ Recessed mounting Mid power SMD type LED Lightfixture not less than 50mm housing depth made from CRCA sheet steel housing, high purity /transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with4 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , withShort & Open circuit protection (Integral with light fixture). System lumen efficacy of = 120 lm/Watt,THD < 10 % , p.f.=0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intialLumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) ,maximum power consumption should not more than the specified rating and Fixture shall be of BISstandard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/Screen printing on housing.OEM must have its own in house NABL lab setup for all testing facilities for LEDfixtures. (LM79 &LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer incharge. All as per pre approved by Engineer in charge. For additional technical parameters ofproducts/ work , refer Annexure \"A\" attached with this BSR . |
| 240 | Surface Moutning |
| 241 | Minimum lumen output 4200 lm |
| 242 | Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy = 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.=0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate/ Report from OEMshall besubmitted. All asper pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 243 | 1170mm(+/-10%) LED batten with min. lumen output 2200 lm |
| 244 | Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheetnot less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC61439- 1 & 3, powder painted complete with reversible door (fordouble door DB only )100 amp. insulated copper bus bar/shortinglink , copper neutral link, copper earth link , color codedinterconnecting wire set of suitable rating and dinbar,maskingsheet, making internal DB terminations with copper lugs, Ferrules,detachable gland plate, including making connections, testing etc.as required. OEM shall have submit NABL / CPRI / ERDA accrediatedlab type test reports & All as per pre approved by Engineer incharge. For additional technical parameters of product / work referAnnexure \"A\" attached with this BSR |
| 245 | Metal door (single phase) IK-09 and IP-43 with Metal end box |
| 246 | 6 Way (6+2) |
| 247 | Metal door (Three phase) IK-09 and IP-43 with Metal end box |
| 248 | 6 Way |
| 249 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type ofload and site requirement) 4 KV impulse withstand voltage, ISImarked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. ,conductor line load reversibility , IP 20 contact protection and fittedin existing distribution board/sheets, minimum electrical operation20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A &above rating including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab typetest reports & All as per pre approved by Engineer in charge. Foradditional technical parameters of product / work refer Annexure\"A\" attached with this BSR |
| 250 | Double pole MCB(With B/C curve tripping Characteristics) |
| 251 | 40 A rating |
| 252 | 6 A to 32 A rating |
| 253 | Single pole MCB (With B/C curve tripping Characteristics) |
| 254 | 6 A to 32 A rating |
| 255 | Triple pole MCB (With B/C curve trippingCharacteristics) |
| 256 | 50/63 A rating |
| 257 | Four pole MCB (With B/C curve tripping Characteristics) |
| 258 | 50/63 A rating |
| 259 | Providing & Fixing of Recessed/surface mounting heavy dutyVertical TPNDistribution board with Metal end box with provisionof incomer suitable for MCB / RCCB and SP / TP MCB as outgoing,made out from Galvanized steel / CRCA sheet not less then 1.2 mmthick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3. powderpainted with reversible door (for double door DB only ) completewith insulated 100 A rating copper bus bar, neutral bars withshrouds, earth bar , color coded interconnecting wire set ofsuitable rating and din bar,masking sheet, making internal DBterminations with copper lugs, ferrules, detachable gland plate,including making connections, testing etc. as required. OEM shallhave submit NABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge.For additionaltechnical parameters of product / work refer Annexure \"A\" attachedwith this BSR |
| 260 | Double door IK-09 & IP-43 with Metal end box |
| 261 | 6 Way(8+18) |
| 262 | Supplying and drawing FR PVC insulated & unsheathed flexible copperconductor as per PWD specification for electrical Works with ISImarked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire shouldbe made from 99.90 % purity copper, class 5 stranding in acc. toIS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping makingconnections with Copper Lugs of suitable size, Ferrules,testing etc. asrequired. OEM Must have its own in house NABL lab setup for alltesting facilities for wires. For additional technical parameters ofproduct / work refer Annexure \"A\" attached with this BSR |
| 263 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 264 | 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. |
| 265 | 3x 1.5 sq.mm |
| 266 | 4 x 6.0 sq.mm |
| 267 | 1 x 4.0 sq.mm |
| 268 | S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P -III ) PVC conduit along with ISI marked (IS:3419-1988) accessories asrequired in recess including cutting the wall, covering conduit andmaking good the same as required. For additional technical parametersof product / work refer Annexure \"A\" attached with this BSR |
| 269 | 20 mm |
| 270 | 25 mm |
| 271 | 32 mm |
| 272 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-ArrmouredAluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4-Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %,Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware /PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testingetc. as required of following size. OEM must have it\"s own in house NABL accrediated Laboratory for testing procedure as per IS:10810. For additionaltechnical parameters of product / work refer Annexure \"A\" attached with this BSR |
| 273 | 4.0 Sq. mm |
| 274 | 3 core |
| 275 | 25.0 Sq. mm |
| 276 | 3.5 core |
| 277 | Supplying and making one end termination with Nickel plated heavy dutybrasssingle compression gland (as per IS 12943-1990)) SIBG type consisting of CheckNut, Gland Body, Metal Washer(3 Nos.), Outer Seal Rubber Ring, CompressionNut, heavy duty aluminium lugs (as per IS 8309 -1993) duly crimped withcrimping tool, PVC tape as per IS 8337-1976 of following size of PVC insulated& PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade asrequired.All as per pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 278 | 3 x 4.0 sq.mm |
| 279 | 3 x 25.0 sq.mm |
| 280 | Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulb inexisting holder or fixture as required with system lumen efficacy =100 lm/Watt output ,pf0.95 , CRI >70, minimum life time of minimum 25000 Burning Hours with , 70% of intialLumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As perANSI Bin) , maximum power consumption should not more than the specified rating andFixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures WordMark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own inhouse NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate /Report from OEM shall be submitted. All as per pre approved by engineer in charge . foradditional technical parameters of product/ work, refer Annexure \"A\" attacheded with this BSR |
| 281 | 9 Watt |
| 282 | Providing & Fixing of of Double ball bearing, copper wounded capacitorstart single phase metallic blade fresh air fan, in existing openingincluding cost of hardware , flexible 3 core copper conductor ,makingconnections, testing etc. as required. All as per pre approved by Engineerin charge. For additional technical parameters of products/ work , referAnnexure \"A\" attached with this BSR |
| 283 | 300 mm sweep |
| 284 | Providing & Fixing of Heavy duty capacitor start, copper wound Doubleball bearing 900/1400 RPM single phase Exhaust fan conforming toIS:2312 ISI marked in existing opening including making connectionstesting etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work , refer Annexure\"A\" attached with this BSR . |
| 285 | 300 mm sweep(900/1400 RPM) |
| 286 | 380 mm sweep(900/1400 RPM) |
| 287 | Providing & Fixing of HDPE pipe Confirming to IS:4984:2021 forwater supply suitable for submersible & jet pump with requiredfittings ie socket, elbows, tee etc. complete in all respect. All as perpre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached withthis BSR |
| 288 | for vertical installation |
| 289 | 75 mm OD 6 kg / cm2 |
| 290 | 40 mm OD 4kg/ cm2 |
| 291 | Plate Earthing as per IS:3043 with copper Earth plate of purity >95% ofsize 600mm x 600mm x 3.0mm by embodying 3 mtr. below the groundlevel with 20 mm dia. G.I. \"B\" class watering Pipe ,including all accessorieslike nut, bolts, reducer, nipple, wire meshed funnel, and Heavy dutyweather proof poly-propylene earth pit chamber with lockable Jam freelid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm.andembodying the pipe complete with alternate layers salt and coke/charcoal, testing of earth resistance for value of 5 ohms or less asrequired & must record by engineer in charge during site visit and ensureto enter in measurment book. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , referAnnexure \"A\" attached with this BSR . |
| 292 | Supply and installation of high tensile low carbon steel rod molecularlybonded with 99.9 % Copper thickness (250 microns) and confirming toUL 467, IS/IEC 62561-2 of following size and length and as per pointmentioned (a), (b), [c), (d), (e) below :-(a) Bore a hole of dia. 100 mm of required length, Place the rod in thecentre of Hole |
| 293 | filled with anti corrosive conductive compounds with the permanentsealings at both the ends, CPRI/ ERDA tested with RMS capacity ofminimum 30 KA for withstanding 1 second .To ensure the moisturecontent and electrical conductivity, 25 kg for 2000 mm & 50 Kgs for3000mm of resistance lowering earth enhancement material shall beused as a backfill compound. The compound shall be tested form NABLacredeated lab for low resistivity ( less than 0.12 Ohm - meter ) & highconductivity in nature with carbon as a major content as per referance of IS 3043-1987,IEEE 80-2013 (clause 14.5d) , IEEE 837 & IER 1956 withlatest amendemnts |
| 294 | Connect the rod with copper Strip/Conductor/Wire with suitableclamp made from tinned copper and SS 304 BoltPlace Heavy duty weather proof poly-propylene earth pit chamberwith lockable Jam free lid suitable for safe working load 5000 Kg or moreof size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height250 to 300 mm. |
| 295 | Testing of earth resistance for value of 5 ohms or less as required &must record by engineer in charge during site visit and ensure to enter inmeasurment book. Test certificates for confirming above standards from OEM ismandatory. All as per pre approved by Engineer in charge. For additionaltechnical parameters of products/ work , refer Annexure \"A\" attachedwith this BSR . |
| 296 | 25 mm thick and 3 Mtr. Long |
| 297 | Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required. All asper pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 298 | 8 SWG G.I. ( Hot Dipped ) Wire |
| 299 | 10 SWG copper. Wire |
| 300 | Supply & Laying following size earth strip in horizontal or vertical run insurface by means of Earth strip DMC Insulator including riveting/soldering/ welding, Jointing shall be done by overlapping and with 2 setof Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at50cm making connection etc. as required.All as per pre approved byEngineer in charge. For additional technical parameters of products/work , refer Annexure \"A\" attached with this BSR . |
| 301 | 25mm x 3mm G.I. ( Hot Dipped ) Strip |
| 302 | Providing & Fixing of IK08 IP-66 protected high power LED flood light system with single piece Pressurediecast aluminium housing, toughened glass diffuser with suitable lenses on LED to achieve various beamangles, of high power LED of 3 to 5 watt each . Integrated potted driver as a unique BIS R number havingefficiency more than 85 % and in compliance to BIS certified and Trade mark certificate. The System levelLuminaire efficacy >=125 lm/ wt. LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff@>=300 V AC and Auto resetting Safety .Power Factor >0.95 , THD(I) <10% , driver current <=750mA.driver should be Phase to phase protectionof 440 V for 4 Hrs. Electrical Connector , Surge Protection Min>=4KV internal and 10KV external but inside driver compartment, System life of 50000 Burning hourswith 70% of Initial Lumens maintained, CRI>70 andCCT5700K355K.ManufacturesWordMark/NameEngraved/Embossing/Screen printing on die cast housing to allow traceability/authenticity. Fixture shallbe IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LEDfixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shallbe submitted. All as per pre approved by Engineer in charge. Foradditionaltechnical parameters ofproducts/ work , refer Annexure \"A\" attached with this BSR |
| 303 | High Power LED Flood Light Minimum lumen output 14800 lm |
| 304 | Providing & Fixing of Street light bracket made out from following size of \" B \" class , Medium class G.I.Pipe confirming to IS : 1239 P - 1 ( 2004 ) with heavy duty pole clamp, Saddles suitable fastners etc. asrequired. All as per pre approved by Engineer in charge. For additional technical parameters of products/work , refer Annexure \"A\" attached with this BSR . |
| 305 | 32 mm Dia. |
| 306 | Providing & Fixing of BEE Star rated copper wounded double ballbearing capacitor start, aluminium body & Metallic blade ceiling fanConforming to all the performance requirements laid down in IS374:2019 including all amendments, as applicable ; & Carry BIS licensing(i.e. ISI marking) with down rod up to 80 cm with secondary supportsafety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulatedflexible copper conductor making connection testing etc. as required. Allas per pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached with thisBSR . |
| 307 | 1400 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) |
| 308 | 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) |
| 309 | P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm lengthextended on each side . All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure \"A\"attached with this BSR |
| 310 | Providing & Fixing of modular type 120 W Step Fan regulator duly ISImarked (IS 11037:1984 ) with CM/L no. printed made out of unbreakableand fire retardant vergin poly carbonate with brass terminals and captivescrews & silver alloy contact tip with IP-20 rating , including all as per preapproved by Engineer in charge,making connections, testing etc. asrequired. For additional technical parameters of product / work referAnnexure \"A\" attached with this BSR |
| 311 | 5 step fan regulator 2 Module 360 dgree rotating |
| 312 | Providing & Fixing of following modular accessories as per PWDspecification for electrical Works, made out of unbreakable and fireretardant vergin poly carbonate with brass terminals and captive screws &silver alloy contact tip with IP-20 rating , including all as per pre approvedby Engineer in charge,making connections, testing etc. as required. Foradditional technical parameters of product / work refer Annexure \"A\"attached with this BSR |
| 313 | RJ-11 telephone jack single line |
| 314 | Blanking plate |
| 315 | P & F Krone module with base frame in the recess / surface made out of1.2 mm thick sheet steel box, front openable, having locking arrangementsduly powder painted,including dressing, ferruling and punching oftelephone cable with krone tool etc. as required. For additional technicalparameters of product / work refer Annexure \"A\" attached with this BSR |
| 316 | 10 Pairs |
| 317 | Providing & Fixing of extra down rod of 15 mm dia . ERW (Electricalresistance welded ) of 1.6mm nominal thick medium duty steel pipeincluding cutting, threading, drilling, fixing quarter pin etc as reqd. All asper pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached with thisBSR |
| 318 | P/Laying ISI marked P.V.C. insulated submersible cable confirmingto(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should bemade from 99.90 % purity copper, stranding in acc. to IS:8130/IEC60228 for lower watt loss , oxygen free for less chances of oxidization,insulation PVC type A/C/D , flame retardant as per IS 10810-53, betteramperage rating as per IS:3961 part 5, existing pipe / open trench /Cable tray / on surface including making connection etc. as required.For additional technical parameters of product / work refer Annexure\"A\" attached with this BSR |
| 319 | 2.5 Sq.mm 3 core flat / Round |
| 320 | SITC of 3 /4 pole current limiting Moulded case circuit breaker (MCCB)made of flame retardent & heat resistant material having followingcurrent rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L &S/C settings , conforming to IS/IEC 60947 P -2 :2003 with front face andcentralised adjustable, trip free mechanisum, true contact positionindicator, line load interchangeability, designed for both horizontal &vertical mounting without any adverse effect on electrical performance,suitable for operation upto 55 degree and without derating upto 40degree, pollution degree 3, having positive isolation capability, push(test) to trip, trip time less then 10 ms under s/c condition, Breakingcapacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 690 V.provision for UVR , shunt trip , earth fault trip, door interlock, pad lock &rotary handle , including making connections etc. as required.OEM shallhave submit NABL / CPRI / ERDA accrediated lab type test certificatebefore execution All as per pre approved by Engineer in charge. Foradditional technical parameters of product / work refer Annexure \"A\"attached with this BSR |
| 321 | 4 pole MCCB With Thermal Magnetic release |
| 322 | up to 100 Amp , 10 kA, fixed O/L & fixed S/C setting |
| 323 | Providing & Fixing of ISI marked (IS:371) 6 amp surface type 3 pin ceilingrose with CM/L no. printed and made out from industrial gradePolycarbonate or fire resistant ABS material, brass terminal & captivescrews including making connection testing etc. as required.All as per preapproved by Engineer in charge. For additional technical parameters ofproducts/ work , refer Annexure \"A\" attached with this BSR |
| 324 | Supplying and drawing PE Insulated & PVC Sheathed unarmouredtelephone cable with 0.5 mm dia. Solid Annealed electrolytic gradebare Copper Conductor as per IS: 8130/84 &confirming to TECspecification GR / WIR/06-03 March 2002 in existing surface orrecessed conduit/casing capping. including ferruling on each pair forIdentification etc. as required. For additional technical parameters ofproduct / work refer Annexure \"A\" attached with this BSR |
| 325 | 2 pair |
| 326 | Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC,UTP (Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable asper latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balancedtwisted in pairs, seperated by a cross-member fluted pair divider & protected by PVCJacket. Certified performance in a 4-connector configuration upto 100 Mtrs channelrequirements & transmission frequencies up to 250 Mhz. in existing MS/PVCConduits/casing capping including making connections to Information outlets and PatchPanels with jack & ferruling at both ends for identification with necessary tools forpunching, stripping, crimping and testing etc as required complete in all respect. All as perpre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . |
| 327 | Supply & fixing of square Faceplate for Flush / Surface Mount Information OutletsSingle/Dual or Quad Aperture , material should be PC+ABS body, Suitable for RJ45unshielded/shielded connection modules. Should match with I. O. OEM. Dimensions shouldbe 86mm X 86mm as required complete in all respect. All as per pre approved by Engineerin charge. For additional technical parameters of products/ work , refer Annexure \"A\"attached with this BSR |
| 328 | Single Aperture |
| 329 | Supply, Installation, Testing and Comissioning of Rack mounted 19\" 1U, Cat6 24 Portloaded, 1.5-1.6 MM CRS chasis, powder coated, sheet steel, made of plastic (ABS), ModularPatch Panels with Rear Cable management system and mounting hardware to mount thepatch panel. Should have port identification numbersprinted/engraved on front of thepanel. Etc. as required.All as per pre approved by Engineer in charge. For additionaltechnical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 330 | Modular Patch Panel Loaded with Cat -6 I/O |
| 331 | Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A /Class E/Ea patchcords should be constructed of minimum 23/24 AWG, stranded bare Copper cable withFRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectorswith strain relief boots as per ANSI/TIA/EIA 568-C.2 suitable for Cat 6/6A applicationcomplying to latest ammendments Category 6/6A Standards, According. to TIA568C.2,ISO/IEC 11801, EN 50173, IEC 60603-7-51, EN 60603-7, IEEE 802.3an minimum requirementfor 1G BASE-T to 10G BASE-T performance. Patch cords shall be straight thru cablecompatible with both T568-A and T568-B wiring schemes, should support IEEE 802.3af /IEEE 802.3at for POE applications, Minimum 750 to 1000 mating cycles in plug contacts forlong durability, Should support Ethernet 10GBASE-T, 1.2 Gb/s ATM, Token ring 4/16, Digitalvideo and broadband/baseband analog video, Voice over internet protocal (VOIP).All as perpre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . |
| 332 | Cat 6, U/UTP (Unscreened/Un-sheilded Twisted Pair) Patch Cord |
| 333 | 1 Mtr |
| 334 | Supply & Installation of IP-20 & IK-08 , UL Listed Wall mounted Double SectionCommunication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet,front sturdy sheet steel frame folded from one piece and welded with minimum 5mmtoughened glass door,Vertical Mounting Rail 1.6 MM with \"U\"Marking , with All roundprotective channel on the door aperture, lock integrated on front door, top and bottomcover with cable entry provision with gland plates, integrated side walls, 2 pair of 19\" angleswith wall mounting provision on wall. Accessories like: 1 No of 19\" 1U Horizontal Cablemanager, 1 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware , 1 No of19\" 1U, mountable socket strips with 5 nos of 5A universal sockets with 2 mts long powerchord for supplying power to switches, fans etc along with earth continuity kit, indicator,moulded power supply cable. fixing on wall with Suitable Anchor fastner etc as required.Allas per pre approved by Engineer in charge. For additional technical parametersofproducts/ work , refer Annexure \"A\" attached with this BSR . |
| 335 | 9 U Rack with Width 600 mm & Depth 400 mm + 100 mm |
| 336 | 6 U Rack with Width 600 mm & Depth 400 mm + 100 mm |
| 337 | Supply , Installation, Testing and Comissioning of Managed Layer-2 Intelligent 10/100Ethernet Switch providing 24 x 10/100/1000 MBPS Giga Ethernet ports / with min 2 SFPGiga Ports (provision for Fiber Giga connectivity) with related LANBase Software includingmaking connections etc as required.All as per pre approved by Engineer in charge. Foradditional technical parameters of products/ work , refer Annexure \"A\" attached with thisBSR |
| 338 | Supply and Installation of unsheilded/360 degree sheilded Information outlets made of highimpact plastic body with ABS, FR Grade halogen free material with provision for protectionagainst dust in jack, suitable for Cat 6/6A application complying to latest ammendments,According. to Cat. 6/6A channel, It should support channel as well as componentsrequirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6Aunshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWGsolid/strandedwire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jackshould have tooless/impact termination on reliable copper tin plated Insulationdisplacement contact, with easy lock mechanism, It supports IEC 60603-7-4 and compliedwith ANSI/TIA/EIA 568 C.2 standard. jack should be RJ11,RJ12 & RJ45 compatible. Shouldsupport Ethernet 1.2 Gb/s ATM,Digital video and broadband/baseband analog video, Voiceover internet protocal (VOIP) Specifications in existing modular/MS Boxes along withnecessory connections as required.All as per pre approved by Engineer in charge. Foradditional technical parameters of products/ work , refer Annexure \"A\" attached with thisBSR . |
| 339 | Cat 6, Un-sheilded Information Outlet |
| 340 | Providing & Fixing of Vertical(BEE 5 star rated) / Horizontal( BEE 3 starrated) storage water heater with outer casing made of EngineeringPlastic sheet (Upto 25 Ltr) / Metal rust proof Body (35 & 50 Ltr), Glass -line / Titanium Enamel coated Pressure Pump Compatible 8 bar pressureInner tank, Glass Line Coated , mineral filled heating element, stem type,snap action adjustable thermostat , Dual indicating lamps Injected PUFinsulation, Multi Function Valve etc. as required held in position with2/4 no. 10/12 mm anchor Fastener, duly wired with 3 core 2.5/4.0Sqmm PVC insulated & sheathed copper conductor and 16 A/25A threepin plug top with Portable Residual Current Device ( PRCD ) , includingmaking inlet, outlet Flexible alloy connection, testing etc. as required.All as per pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached with thisBSR . |
| 341 | 25 Ltr |
| 342 | Supply & Fixing of Dry Powder Agent (as per IS 4308:2019), ABC type FireExtinguisher (Stored Pressure type) conforming to IS:15683:2018 , Powdercoated Internal & External Surface Deep drawn cylinder body of Mild SteelCR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve withInbuilt safety release device, Diaphragm Type, 0 to 28 bar range pressuregauge, 450 mm long EPDM discharge tube, QR code for Product Traceabilityincluding Fixing on wall with suitable Anchor Fasteners as required offollowing capacity. Test Certificates of all the Parameters along with Hydrotest & Burst test (For Cylinder Body) Certificate from OEM / External NABLAccrediated Lab is to be submitted. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , referAnnexure \"A\" attached with this BSR . |
| 343 | 6 kg |
| 344 | Providing & Fixing of IP-20 LED Recessed / Surface Mounted, Round / Sqaure SMD MidPower LED Downlight with power coated die-cast aluminum housing with UV Stabilizednon yellowish Diffuser with BIS complience 2.5 KV surge protected Isolated driver, withShort & Open circuit protection, having efficiency > 85% . System Lumen efficacy of = 110lm / watt, THD < 10 % , Pf.=0.95, CRI >80, life time of minimum 50000 Burning Hours with ,70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K/ 5700°K/6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more thanthe specified rating and Fixture shall be of BIS standard and trade mark certificate( T.C.).Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures.(LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approvedby Engineer in charge. For additional technical parameters of products/ work , referAnnexure \"A\" attached with this BSR . |
| 345 | Surface Mounting (with extruded alumn. Housing ) |
| 346 | Minimum lumen output 650 lm |
| 347 | Minimum lumen output 1950 lm |
| 348 | P & F 1.2 mm thick G. I. / M .S. Sheet boxes duly finished with twocoats of red oxide and with earthing terminal of following sizes(nominal size) in recessed/surface as required.For additionaltechnical parameters of product / work refer Annexure \"A\" attachedwith this BSR |
| 349 | 1.2 mm thick M. S. Sheet boxes |
| 350 | 75mm x 75mm x 60mm |
AI Tender Summary
Tender Timeline
Jun 08, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedJun 28, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 29, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender