C S Item On Conversion Supply Basis And Forged Steel Item , C.S Coupling Having Material As Per Is:1030 Grade 280-520W For Mill Size 30X60 As Per Drg. , Supply Basis , Conversion Basis , Machining Charge , Cast Steel Crown Pinion Having Material Is:2708 Grade-Iii-B For Mill Size 30X 60 As Per Drg. , Supply Basis , Conversion Basis , Machining Charge , C.S.Trash Plate Having Material As Per Is:1030 And Grade-Iii-B , Supply Basis , Conversion Basis , Machining Charge , Teeth Cutting / Grooving Of Trash Plate As Per Drg. , C.S.Trash Beam As Per Is-1030 / Is 2708 As Per Drg. , Supply Basis , Conversion Basis , Machining Charge , Forge Steel Tail Bar For Taxmaco And Kcp Mill Having Material C-40 / 8 As Per Drg. Mh- 6 & Mh-56 , Supply Basis , Conversion Basis , Forge Steel Pinion For Transmission Gear Of Taxmaco Mill As Per Drg. No. Mh 39, Material En-24, Tensile Strength70-80 Kg. / Sqcm, Hardness 200-220 Bhn , C.S.Bearing Housing For Taxmaco Mill As Per Deg No Mh-17-C / 04 Side Roller Housing , Supply Basis , Conversion Basis , Gun Metal Bearing Housing For Taxmaco Mill As Per Deg No Mh-17-C / 04 Top Roller Housing , Supply Basis , Conversion Basis , C.S.Bearing Housing For K.C.P.Mill As Per Drg No Mh-17-B Side Roller Housing , Supply Basis , Conversion Basis , C.S.Bearing Housing Fork.C.P.Mill As Per Drg No Mh-17-B Top Roller Housing , Supply Basis , Conversion Basis , C.S.Gear Coupling For C / F Machine As Per Drg.No.Bh-14 ( Duly Case Hardness ) , C.S. Pinion For Cane Unloader As Per Drg, Cu- 16Teeth-17 , Teeth -18 , C.S.Sprocket 2 Pitch ( Both Pilot Bore ) , ( I ) No Of Teeth 18 , Boss Dia 3 , ( Ii ) No Of Teeth 36 , Boss Dia 6 , C.S.Sprocket For Boiler Rotary Feederas Per Drg.Blr-73 / 1 Pitch- 25.0 Mm, No Of Teeth 21, Od -180Mm. P.B -25Mm , C.S.Sprocket For Bagasse Elevator ( Pilot Bore ) As Per Drg.Mh-75 Pitch 50.8 Mm, No Of Teeth 50, Od 842.70Mm. Pcd 808.7Mm, Teeth Thickness 28Mm , Boss- 270X130 Mm , Cs Sprocket ( Pilot Bore ) As Per Drg.Blr-62Pitch 50.8 Mm, No.Of Teeth-14 Pcd 226.49Mm, Od 258.8Mm , Static Coller Of 25 Mm Thick Duly Hard Faced Of 5 Mm Thick Layer . Total Thick 30 Mm After Hard Facing For Taxmaco & Kcp Mill As Per Drawing No. Mm 105 , ( I ) M.S. Material , ( Ii ) C.S.Material , Sprocket Of Inter Carrier Od 280 Mm, No.Of Teeth45.Pitch 19.5 Mm , C.S. Sprocket ( Duplex ) For Enter Carrier Teeth 12, As Per Drg. Mh-72 / Sample , S.S. Wear Plate Is 304 Quality , ( I ) Length 435 Mmx Width 370 Mmx Thick 15 Mm , ( Ii ) Length 385 Mm X Width 330 Mm X Thick 15 Mm , C.S.Tresh Beam Bracket As Per Sample / Drg. , C.S.Eccentric Pin For Taxmaco As Per Sample / Drg. , C.S. Trash Beam Adjusting Connecting Rod For Taxmaco Mill, As Per Drg. Mh- 297 , C.S. Bridge Wheel For Cane Unloader As Per Drg. Cu25 ( 1 ) , , Trolly Wheel For Cane Unloader As Per Sample / Drg. , Pinion Gear Set For Cane Unloader As Per Sample / Drg , C.S. Pinion ( Gear ) For Rbc Cross Carrier Pitch 41Mm. Teeth 25 , Type Of Teeth In Valute ( Spur ) Module 12.7 Mm Width 125 Mm .Od 343 Mm, Bore 2 Dia As Per Drg. , Clutch Shaft For Mill. As Per Drg. Mh-76 , En-8 , For Taxmaco Mill -Sl.No.2 , For Kcp Mill - Sl.No.1 , Cs Worm For Crystilizer Wheel Od 290 Mm, Bore 81 Mm.Pitch 80 Mm Complete , Groving Of C.Strash Plate As Per Drg. , Idler Wheel Gear For Cane Unloader., No Of Teeth 68, Od-420 Mm, Module-6, Pitch- 18.84 Mm, Pcd-408 Mm, As Per Drg. No. Cu-25I , Pinion For Cane Unloader No. Of Teeth- 33, Od-212 Mm, Pcd-198 Mm, Pitch- 18.84 Mm, Module-6 As Per Drg. No. , Pinion For Cane Unloader No. Of Teeth- 18, Od-200 Mm, Pitch- 35 Mm, Bore- 50 Mm, Width-115 Mm, Module-6, Teeth Depth-25 Mm As Per Drg. No. , Break Stand Complete For Cane Unloader, Size-10 , Chief Engineer
