Tender For Construction Of 1000Mt Capacity Godown At Tirupathur Regulated Market In Tirupathur District.
Tender Value
1.23 Crore
Estimated cost
Bid Submission
08 Jun 2023
0 days left
EMD
1.45 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tirupathur → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Construction Of 1000Mt Capacity Godown At Tirupathur Regulated Market In Tirupathur District.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. |
| 2 | Supplying and filling in foundation, basement, etc with filling M sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 3 | Providing and laying sand gravel mix 1:1 ratio to a consolidated thickness of 15cm using 0.631 cum of sand 0.675 cum of gravel per one cum of compacted volume of sand gravel mix including cost and conveyance all materials to site and stacking for pre-measurements and including labour charges for mixing laying and compacted by powerroller and hire charges of all tools and plans employed etc complete. |
| 4 | Cement Concrete 1:5:10 (One Cement, Five M sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification |
| 5 | Plain Cement Concrete 1:2:4 (one cement, two M Sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specifications and as directed by the departmental officers |
| 6 | Cement Concrete 1:1-1/2:3 (One Cement, One and a half sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers |
| 7 | a) Foundation & Basement |
| 8 | b) For superstructure in Ground floor upto 4.50m ht. |
| 9 | Vacum dewatering on freshly laid and thoroughly vibrated concrete surface to produce a homogeneous and smooth concrete surface. Suction mat shall be spread over the leveled fresh concrete surface and shall be connected by suction house to the vaccum pump for dewatering of surplus water in the concrete.After dewatering is complete, the concrete surface is troweled with minimum two passes to achieve a wear resistance concrete surface . |
| 10 | Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.(Contractor has to make his own arrangements for the supply of steel and binding wire) |
| 11 | Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require Only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid) |
| 12 | a) For column footing plinth beam bed blocks templates staircase, steps piers raft, beam raft slab ect., |
| 13 | Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) |
| 14 | a)For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. |
| 15 | b) For plane surfaces such asrectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc |
| 16 | Brick work in following Cement Mortar using 1:5 Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction. |
| 17 | a) For Foundation and Basement |
| 18 | Brick work in following Cement Mortar using 1:6 Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction. |
| 19 | a) For Super Structure in Ground Floor up to 4.50 M ht |
| 20 | Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. |
| 21 | Special ceiling plastering and finishing all the RCC exposed surfaces such as RCC Slabs sunshade, canopy, staircase steps, landing slab etc., with cement mortar 1:3 [one cement and three sand] 10mm thick including hacking the surface and providing cement mortar noising beading wherever necessary using the same mix as directed by the departmental officers etc., complete complying with standard specifications. |
| 22 | White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed. |
| 23 | Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. |
| 24 | Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 25 | Supplying and fixing of rolling shutters with ISI mark shall be of pull and push type made out of 18/Gx3’ lath sections with consists of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below; Curtain; Shall be of 18/Gx3’ lath sections cut to required size and filled with heavy cast iron/ M.S. Clips for 8’0”[2.45m] high rolling shutter lath sections provided shall be not less than 37 numbers. Lock Plate; Shall be 10 G.M.S.Sheet reinforced with 40mmx 6mm M.S angles at the bottom and fitted with heavy latches and locking arrangements on either sides.There should be on handle on either side Guide channel; Pressed guide channels shall be of 10 G.M.S.Sheet and attached to the side brackets with 20mm square bar. Side brackets shall be of 10 G.M.S.Plate and cost iron ‘U’ clamps shall be reveted to the side brackets Roller; Shall be of heavy cast iron pullies fitted with heavy duty C’ Class 40mm steel pipes and high tensile high carbon coil springs-2 springs shall be supplied. Supplying and fixing of Hood Cover; Shall be of 0.9mm CRCA sheet reinforced with 25mm x 25mm x 3mm M.S. angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated with heavy coat of zinc chromite primer. The above specifications for various components of rolling shutter shall be invariably followed and verified with the rolling shutters supplied by the firms at site. If the rolling shutters supplied do not confirm to the above specifications, the concerned firms should be asked to replace the shutter or supplythe missing components. |
| 26 | a) Gear operated type (from 8 m2 to 12 m2 area) |
| 27 | Fabricating and supplying and erecting the required number of trusses with structural steel members like angle iron MS plates for all truss members including cleats to receive the purlines all cutting drilling holes welding and fixing of members with necessaryThe welding should be done with submerged arc welding to full length.The rate inclusive of the cost of painting the memebers with one coat of primer of Zinc chromite and enamel paint etc., complete complying with standard specification and as directed by the departmental officers. |
| 28 | Supplying and fixing in position of Iron grills of required size using 32 x 32 x 6mm angle around and 2 Nos of vertical at center with MS flats diagonally to the existing open space for grills into necessary hold fast conveyance and one coat of primer etc., |
| 29 | Manufacturing and supplying and fixing in position of ‘N’ type ventilators of required size made out of 25x25x5mm MS “L” angles frames alround the ventilator. MS TEE of 25x25x5mm to be fixed in between the frames at 30cm intervals. Hold fast to be used 25x25x5 mm “L” angles 23 cm length 4 Nos 3mm pin headed glass to be fixed in-between the angles by usin teak wood beadings of size 15x12 mm wth screw, washer and nut wherever necessary. In the inclined portion, “1x1” weld mesh to be embedded by using 25x5 mm Flat at 30cm centre to centre 12mm sq steel rods to be fixed horizontally between the frames in vertical portions at 10cm centre to centre(Approximate). The rate inclusive of transporting charge, dismantling, redoing to the original condition, one coat of red oxide primer etc., complete complying with standard specification and as directed by the departmental officers. |
| 30 | Supplying and laying of profiled galvalume sheet of TCT 0.5mm and standard width of 1.060mm with yield strength of 550MPA of approved quality for roofing with necessary U or J bolts and unts Bitumen GI washers etc.,complete complying with standard specification and as directed by the departmental officers during execution of work. |
| 31 | Supplying and fixing corrugated PolyCarbonate Sheet of size 3mx1.06m on the roof in between the colour coated Galvolume sheets for proper lighting with necessary screws and EPDM rubber washers, etc. as complete Complying with standard specification and as directed and specified by the departmental officers. |
| 32 | Supplying and laying of Gal volume sheet ridge pieces approved quality with necessary U or J bolts and nuts GI washers etc., complete complying with standard specification. |
| 33 | Supplying and fixing of Rotary Ventilators with all purlins on the roof with necessary bolt & nut arrangement to with stand the wind velosity as specified by the departmental officers. |
| 34 | Providing Groovecuttinginflooringconcretefor10mmwidthand20mmdepthandfilling the groovewith combinationofAnabondTuffseald2Gandbitumen tarincludingcostofallmaterialsandlaboursetc.,complete. |
| 35 | Providing Pre construction of Anti termite Treatment for the Construction of building including all chemicals as per standard specifications. Labour charges for preparing the areas for treatment, spraying chemicals and other incident charges etc.,complete. The rate shall be inclusive of giving anti termite treatment to the building for the following four stages including breaking the termite moulds, making holes with crow bars at an interval of 30 cms to a depth of 50 cms in the pheriphery of building and pouring chemicals etc., complete as per ISI 6313 ( Part 2) 2001. The antitermite chemical chloropyriphos 20 EC used should form 0.5% concentrate for the entire operation etc., as directed by the Engineer in charge and including cost of chemicals labour transportation etc.,Stage 1: Spraying Anti termite treatment chemical solution for the foundation before laying the foundation concrete at bottom and sides of the foundation.Stage 2: Spraying Anti termite treatment chemical solution to the grade beam level, spraying has to be done for the grade beam, brick masonry in the super structure in contact with back fill earth.Stage 3: Spraying Anti termite treatment chemical solution on sand for the flooring before laying the flooring concrete; the treatment has to be carried out on the sand filling in basement and after leveling operation is over.Stage 4: Spraying Anti termite treatment chemical solution around the building on outside by making crow bar holes at an interval of15 cms to a depth of 30 cms before laying the plinth projection. These holes have to be closed after the treatment. |
| 36 | Supplying and fixing of Electronic Weighing Scale of Size (600 x 600)mm with stainless steel platform with stainless steel back grill and bright LED display having capacity of (300Kg) with accuracy of (50gm). The display should be of with single phase AC with battery back up and display intensity adjustable for longer battery backup.The machine is also compatible with computer interface RS232 connectivity. The additional functions like indication for AC on net/gross weight, auto zero, battery, battery low count mode, tare function, over load protection with audio alarm and dust proof cover should also be provided in the abovemachine as directed by the Departmental Officers etc., complete.The rate includes conveyance and all other taxes etc., |
| 37 | Supplying and fixing of the Moisture Meter is designed with 2 line 16 character alphanumeric LCD display which displays moisture percentage, temperature, date & time, commodity name, commodity code & pressure (thickness & setting) Moulded Compression Unit with Single volume cup and Data logging with Data storage capacity of 200 readings.The Moisture Meter consists of three Hot keys for any three crops with Calibration for food grains, Pulses, Oil seeds,& Spices etc., with 4% to 30% range, check and Error corrections & Auto calibration with Averaging, Last reading recall facility and Curve programming and Automatic temperature compensation with PT-100 temperature sensor with Weight of 2 Kg and Real time clock.The Moisture Meter to be supplied for having (+) or (-) 0.2 % with quick and precise measurement of consistency and resistance of principle of measurement with Automatic temperature compensation with PT-100 temperature sensor.The error conditions of under range, over range etc.,. The rate inclusive of all taxes, conveyance etc., as directed by the departmental officers during execution of work. |
| 38 | Wiring with 2 x 1.5 sq.mm. (22 / 0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC light point / fanpoint (for electronic regulator) |
| 39 | Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150mm x 100mm x 113mm TW switch box in flush with wall with 3mm thick hylem sheet cover for 5A 3 pin non inter locking wall socket with 5A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point |
| 40 | Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150mm x 100mm x 113mm TW switch box in flush with wall with 3mm thick hylem sheet cover for 15A 3 pin flush type non inter locking wall socket with 15A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC power plug point |
| 41 | Supply and run of 2 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour |
| 42 | Supply and fixing of horizontal type 4 way triple pole neutral MCB distribution board in sheet steel enclosure double door (metal) with 40A 4 pole MCB isolater as incoming and 12 Nos. 6A to 32A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB\"s should be with the ISI mark (like standard make) |
| 43 | Supply and run of 4 x 6 sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in 32mm dia GI pipe (Class \"B\") suitably bent at both ends with necessary angle iron up right and end supports for mains |
| 44 | Supply and run of 4 x 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains |
| 45 | Supply and fixng of TNEB meter board suitable for 3 phase 63A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2\" x 1-1/2\" x 1/4\" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 63A fuse units (500V), 1 No. neutral link, copper earth flat of size 1\" x 1/4\" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete |
| 46 | Supply and laying of 2 x 16 sq.mm PVC armoured LTUG cable in a trench` to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good |
| 47 | Supply and fixing of 2x36w CFL type street light fitting with complete with 32mm dia G.I. pipe class \"B with 1 No 32mm G.I. Bend complete on the post / well with 16A aerial fuse unit on MS plate with PVC unsheathed copper leads, MS clamps and aluminium paiting with 2 Nos 36w CFL. (MakeCG SCE 13236EB / equivalent) (Data)) |
| 48 | Supply and fixing of 4\"40W single industrial type fluorescent fitting complete with copper choke and condensor with conduit pipe suspension from the ceiling with PVC unsheathed copper leads from the terminals to the fitting with fluorescent Tube |
| 49 | Earthing as per the ISI specification with an earth electrode of 2.10 metre Class \"B\" GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry |
| 50 | Supply and run of 1 of No.8 SWG GI wire for earth connection |
AI Tender Summary
Tender Timeline
May 31, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedJun 08, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 09, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender