Supply Of Furniture To Attached Govt. General Hospital At Asifabad In Komrambheem Asifabad District.-50.00 Attendant Cot With Mattress Scope: This Specification Is For The Requirement Of Iron Cots Suitable For General Purpose In Hospitals. Dimensions: Over All Dimensions Of Cot Of Size Top Frame Shall Be Length 1800 Mm, Width 600 Mm And Height 400 Mm. The Various Tubes Used In Manufacture Of Iron Cots Should Have The Following Outside Diameter And Thickness. Component Outside Dia ( Mm ) Thickness ( Mm ) Four Legs Rectangular 75 X 25 X1.60 Mm Thickness Cross Tubes Cr Tubes 25X25 Mm Sq 1.22Mm Thickness The Ms Flat For Top Shall Be Inside All Four Sides Of Size 50X3 Mm Minimum Thickness Of 3.0 Mm. Material: Frame Work Shall Be Of Cr Sheets Conforming To Is: 513 D Quality. Bows & Rectangle & Square Tubes: These Shall Be Made From Cr Steel Tubes. Shoes: These Shall Be Manufactured From Pvc Shoes. Nominal Height Of The Shoe Shall Be 35 Mm. Outside Dimensions Of 3Mm. Manufacture Manufacture The Bed Frame Shall Be Made From C.R. Sheet Double Bent. It Should Be Reinforced With Two Formed Channels To Size 20 X 50 X 50 X 50 X 20 Mm Of 1.25Mm Thickness Flanges Welded Inside The Length Wise. Overall Sizes Of Mattresses Is ( L ) 1800 Mm X ( W ) 600 Mm X ( H ) 75 Mm Of Pu Foam Of 40 Density, Covered With St Rexine Properly Stitched. Finish As Per General Condition Of Tender 20.00 Alamarah With Acrylic ( Glass ) Door Multi Bend Construction And Inter Locking Design And Full Length Over Lapping Doors And Side. Three Way Bolting Mechanism. Spot Welding & Co2 Welded. Front Side Doors With Acrylic Transparent Sheet All Round Frame 70 Mm Borders Thickness 5.5 Mm Thickness Dimensions Outer: 1980 H X 910 W X 480 D Mm A. Top, Bottom, Lh & Rh Sides And Back Material Thickness- 1 Mm B. Removable Rh & Lh Main Doors With Stiffeners Material Thickness =1.22 Mm Almariahs To Be Provided With 4 Full Fixed Shelves Of Inside Shelve Size Of 908 W X 420 D Of Thickness -1 Mm Cr Steel: Cold Rolled Close Annealed Steel Used For Thickness 0.6 To 1.2 Mm Range As Per Is-513 1994 ( Reaffirmed In 1998 ) . Grade ‘D’ Or ‘Dd’ Quality. Chemical Composition, Tensile Properties, Bend Test, Surface, Flatness, Hardness As Per Is-513 1994. Finish As Per General Condition Of Tender With 3 Years Warranty Finish As Per General Condition Of Tender 15.00 Table ( Office Table Big Size ) Dimensions:1450 W X 680 D X 750 H ( In Millimetres ) Material: A.Plb / Plt - Top 25 Mm Thickness. All Plb And Plt ( Prelaminated Twin ) Is Of Following Grade. Grade Ii Type Ii – Designation – Plb-22 ( As Per Is: 12823 – 1990 ) Each Plb / Plt May Contain Following Material Layers: Particle Board, Top With 2Mm Thick Hot Pressed Pvc Beading With Keyboard Moulded Type. C. Under Structure: This Table Should Be Square Cr Tube 30 X 30 Under Structure With Prime Quality C.R Steel Square Tube 1.22Mm Thickness. D. Storage: 3 Draw & 2 Draw Metal Is Provided For Storage. One Side 2 Draw And Other Side 3 Draw Metal Shall Be Provided. Drawer: • Box-Box-File : Dimensions 390 W X 430 H X 560 D Mm, Construction & Material:Welded Assembled, Crca As Per Is-513.• Back , Sides, Top & Bottom , Box 0.6 Think. Drawer Tray & Front- 0.8 Mm. Crca As Per Is-513 , Drawer Slides Used Must Be Of Heavy Duty Telescopic Channels All Steel Metal Components Are Manufactured From Finest Quality Steel, Which Conforms As Per Is-513 Grade D, Dd All Steel Tubes Used For Desk Under Structures Are As Per Is-3601 – 1984, Is-7138-1973, Is-4923-1985. Shoes - These Shall Be Manufactured From Hard Rubber Or Pvc And Shall Be Uniform In Texture And Chemically Inactive To The Action Of Mild Acids. The Nominal Height Of The Shoes, Shall Be 35Mm. With 3 Years Warranty Finish As Per General Condition Of Tender 25.00 Chairs For Office 1. Seat / Back Assembly: The Seat And Back Are Made Up Of 1.2 ±0.1Cm. Thick Hot-Pressed Plywood Measured And Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam. The Back Foam Is Designed With Contoured Lumbar Support For Extra Comfort. The Seat Has Extra Thick Foam On Front Edge To Give Comfort To Popliteal Area. The Chair Is Available In Three Models. Mid Back Size 47.5 Cm. ( W ) X 58.0 Cm. ( H ) *Pch-9U01rg / 9U02rg / 9U12rg Seat Size 47.0 Cm. ( W ) X 48.0 Cm. ( D ) 2. High Resilience ( Hr ) Polyurethane Foam: The Hr Polyurethane Foam Is Moulded With Density = 45±2 Kg / M3 And Hardness Load 16 ± 2 Kgf As Per Is:7888 For 25% Compression. 3. Armrests: The One-Piece Armrests Are Injection Moulded From Black Co-Polymer Polypropylene. 4. Center Tilt Synchro Mechanism ( For 9U01rg / 9U02rg ) : The Mechanism Is Designed With The Following Features: · 360° Revolving Type. · 3 Position Locking · Tilt Tension Adjustment 5. Tubular Frame ( For 9U12rg ) : The Powder Coated ( Dft 40-60 Microns ) Tubular Frame Is Cantilever Type & Made Of Ø 2.54 ±0.03Cm. X 0.2 ±0.016Cm.Thk. M.S. Er.W. Tube. 6. Pneumatic Height Adjustment ( For 9U01rg / 9U02rg ) : The Pneumatic Height Adjustment Has An Adjustment Stroke Of 12.0 ±0.3Cm. 7. Telescopic Bellow Assembly ( For 9U01rg / 9U02rg ) : The Bellow Is 3-Piece Telescopic Type And Injection Moulded In Black Polypropylene. 8. Pedestal Assembly ( For 9U01rg / 9U02rg ) : The Pedestal Is Injection Moulded In Black 33%Glass-Filled Nylon And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Is 66.3 ±0.5Cm. Pitch-Centre Dia. ( 76.3 ±1.0Cm With Castors ) . 9. Twin Wheel Castors ( For 9U01rg / 9U02rg ) : The Twin Wheel Castors Are Injection Moulded In Black Nylon. Overall Dimensions Of Chair Width ( W ) : 76.3 Cm. Depth ( D ) : 76.3 Cm. Height ( H ) : 85.5-97.5 Cm. Seat Height ( Sh ) : 42.5-54.5 Cm Of Featherlite / Godrej Or Equavalent As Directed By The Engineer-In-Charge. 14.00 Office Chairs S Type With Armrest Seat / Back Assembly: The Seat And Back Are Made From Chemically Treated And Seasoned Wood, Caned And Finished With Teak Melamine Polish And Fitting Is Nuts & Bolts System. Back Size: 38.0Cm ( W ) X 40.0Cm ( H ) . Seat Size: 38.0Cm ( W ) X 42.5Cm ( D ) . Cane For Seat / Back: The Caning Used For Seat / Back Has High Tensile Strength As Per Is:5378 Part Ii, 1990. Cane Breaking Strength = 3000Kg / Mm2 ( Min. ) % Elongation At Break = 25% Armrest Tube ( Enh. Ch-7 ) : The Armrest Tube Is Made Of 0 2.54 ±0.03Cm. X 0.2 ±0.016Cm.Thk. Cr. Tube 25.4 Mm 2 Mm Thickness Armrest ( Enh. Ch-7 ) : The Armrest Is Gas-Assisted Injection Moulded From Black Polypropylene. Understructure Assembly: The Under Structure Assembly Is A Cantilever Type Frame Made Of Dia. 25.4Cm. ( 1” ) X 14 Thick Cr Tube.As Per General Condition. Finish As Per General Condition Of Tender 10.00 Office Chairs S Type Without Armrest Seat / Back Assembly: The Seat And Back Are Made From Chemically Treated And Seasoned Wood, Caned And Finished With Teak Melamine Polish And Fitting Is Nuts & Bolts System. Back Size: 38.0Cm ( W ) X 40.0Cm ( H ) . Seat Size: 38.0Cm ( W ) X 42.5Cm ( D ) . Cane For Seat / Back: The Caning Used For Seat / Back Has High Tensile Strength As Per Is:5378 Part Ii, 1990. Cane Breaking Strength = 3000Kg / Mm2 ( Min. ) % Elongation At Break = 25% Understructure Assembly: The Under Structure Assembly Is A Cantilever Type Frame Made Of Dia. 25.4Cm. ( 1” ) X 14 Thick Cr Tube.As Per General Condition. Finish As Per General Condition Of Tender 5.00 Examination Table Scope: This Specification Is For The Requirement Of Patient Examination Table In Hospitals. The Features To Include All The Requirements As Per Examination Table ( Is: 4787-1968 ) With Additional Provisions For Keeping / Storage Places For Minor Medical Equipment. Table, Examination- Table Used For The Purpose Of Examination Of Patients In The Consulting Rooms, Clinics And Side-Rooms Of Hospital Wards. The Main Dimensions Of Examination Table: 1830 ( L ) X 600 ( W ) X 750 ( H ) Mm Overall Sizes Of Mattresses Is ( L ) 1830 Mm X ( W ) 600 Mm X ( H ) 75 Mm Of Pu Foam Of 40 Density, Covered With St Rexine Properly Stitched. Materials: The Steel Cold Rolled Sheet Used For Top And Head Rest Shall Have A Minimum Thickness Of 1.22 Mm. The Thickness. Cold Rolled Steel Tubes Used And Their Corresponding Outside Diameters For Different Parts Shall Be As Given Below: Part Outside Diameter Of Tube ( Mm ) Thickness Of Tube ( Mm ) Vertical Members 31.75 1.2 Horizontal Members 25.40 1.2 Manufacture A- Framework- The Examination Table Shall Have A Framework Of Single Continuous Lengths Of ---- Steel Tubes. At The Floor End, The Four Upright Members Shall Be Connected Together By Longitudinal And Transverse Two Tie Rods And At The Other End These Shall Support A Formed Sheet Metal Top. For Receiving The Sheet Metal Top, The Top Ends Of The Uprights Shall Have An Ms Flat Of 35X3 Mm Thickness Guar Support Rod 10Mm Ms Rod Welded , Thereafter Welded To The Top Can Be Fastened To The Upright Member To The Top So Obtained Study In Construction. The Head Rest Shall Have The Same Construction As The Top And It Shall Be Adjustable On A Rack For Obtaining Various Positions. The Rest Of The Details Shall Be According To 4 Of Ls:4033-1968. Shoes: These Shall Be Manufactured From Pvc / Hard Rubber Bush. Nominal Height Of The Shoe Shall Be 35 Mm. Outside Dimensions Of 3Mm. Mattress: Foam 40 Density Suitable For Use With The Table, 2 Thickness, St Rexene Green Cover To Be Supplied With The Table; All Stitching Shall Be Done With Thread Of Griffon 40 Grade. Finish As Per General Condition Of Tender 50.00 Patient Cot For Adult With Mattress Scope: This Specification Is For The Requirement Of Iron Cots Suitable For General Purpose In Hospitals. Dimensions Over All Dimensions Of Cot Of Size Top Frame ( Sheet ) Shall Be Length 1910 Mm, Width 910 Mm And Height 600 Mm. The Various Tubes Used In Manufacture Of Iron Cots Should Have The Following Outside Diameter And Thickness. Component Outside Dia ( Mm ) Thickness ( Mm ) Bows Outer Cr Tubes -38.10.Mm X 1.60 Mm Cross Tubes Cr Tubes 25.40 X 1.22 Mm Filling Tubes Cr Tubes 19.05 Mm X 1.22Mm The Ms Flat For Top Shall Be Inside All Four Sides Of Size 50X3 Mm Minimum Thickness Of 3.0 Mm. Material: Frame Work Shall Be Of Cr Sheets Conforming To Is: 513 D Quality. Bows & Tubes: These Shall Be Made From Cr Steel Tubes. Shoes: These Shall Be Manufactured From Pvc / Hard Rubber Bush. Nominal Height Of The Shoe Shall Be 35 Mm. Outside Dimensions Of 3Mm. Manufacture Head End: Construction Of The Head End Shall Comply To Meet Requirement Given Bows Shall Be Manufactured From Steel Tubes. It Shall Be Bent, With Inside Radius Of Not More Than 125 Mm At Top 2 Corners Cr Sheet Brackets . Bracket Of 3 Mm Thickness, Shall Be Welded With The Bows Vertical Upright Members Which Allows Frame To Rest On It An Cross Tube: One Horizontal Cross Tube For Making The Structure Of The Bow Rigid Shall Be Welded Between The Vertical Upright Members Of The Bows. Cross Tube Shall Be Welded Below The Sleeping Level At A Height Of 300 Mm From The Bottom. Filling Tubes: The Three Vertical Filling Tubes Shall Be Welded To The Cross Tube And To The Bow. They Should Be Spaced At Regular Intervals. The Height Of The Head End Bow Shall Be About 1075 Mm. Foot End Bow: It Shall Be Similar To 4.1.1 To 4.1.3 Except Leg Bows, Which Shall Be Of 810 Height. Mattress Platform: This Shall Comply With The Requirements Given Below:- The Bed Frame Shall Be Made From C.R. Sheet Double Bent. It Should Be Reinforced With Three Formed Channels To Size 20 X 50 X 50 X 50 X 20 Mm Of 1.25Mm Thickness Flanges Welded Inside The Length Wise. 50.00 Revolving Stool Seat / Back Assembly: The Seat And Back Are Made Up Of 1.2 +0.1 Cm. Thick Hot-Pressed Plywood Measured As Per Qa Method Described In Ocp-Qlta-P14-18 And Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam. The Back Foam Is Designed With Contoured Lumbar Support For Extra Comfort. The Seat Has Extra Thick Foam On Front Edge To Give Comfort To Popliteal Area. Overall Size: 1220 H X 500W X 460 D High Resilience ( Hr ) Polyurethane Foam: The Hr Polyurethane Foam Is Moulded With Density = 45±2 Kg / Nr And Hardness Load 16 ± 2 Kgf As Per Is:7888 For 25% Compression. Armrests: The One-Piece Armrests Are Injection Moulded From Black Co-Polymer Polypropylene. Center Tilt Synchro Mechanism: The Mechanism Is Designed With The Following Features: 360° Revolving Type. Upright Position Locking 1 Tilt Tension Adjustment Seat / Back Tilting Ratio Of 1:3. Tubular Frame: The Powder Coated ( Dft 40-60 Microns ) Tubular Frame Is Cantilever Type & Made Of 0 2.54 ±0.03Cm. X 0.2 ±0.016Cm.Thk. M.S. Er.W. Tube. Pneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Stroke Of 12.0±0.3Cm. Telescopic Bellow Assembly: The Bellow Is 3 Piece Telescopic Type And Injection Moulded In Black Polypropylene. Pedestal Assembly: The Pedestal Is Cr Sheet U Bend 2 Mm Thickness Chromium Coated And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Is 66.3 ±0.5Cm. Pitch-Centre Dia. ( 76.3 ±1.0Cm With Castors ) . Twin Wheel Castors ) : The Twin Wheel Castors Are Injection Moulded In Black Nylon. Finish As Per General Condition Of Tender 50.00 Patient Attendant Stool The Stool Shall Be Used For Bed Side Of The Patient For Their Attendants To Sit. Material Frame Work: As Given In Clause 1.1 Of General Requirements For Hospital Furniture. Top: Stainless Steel Sheet Conforming To Designation 04Cr18ni 10 Or 07Cr18 Ni9 And Shall Have A Thickness Of 1.20Mm. It Shall Also Conform To Of The General Requirements Of Hospital Furniture. Legs: The Legs And Supports Shall Be Made Of Square Pipe Of Size 25 X 25 X 1.6Mm Shoes: These Shall Be Manufactured From Hard Rubber Or Pvc And Shall Be Uniform In Texture And Chemically Inactive To The Action Of Mild Acids. The Nominal Height Of The Shoes, Shall Be 35 Mm. Dimensions. Top: 300Mm X 300Mm Height: 500Mm Height Manufacture: The Frame Work Of Stool Shall Have A Single Continuous Lengths Of Cr Steel Tubes As Shown In Figures Of Indian Standards. At The Floor End, The Four Upright Members Shall Be Connected Together By Longitudinal And Transverse Tie Rods Finish As Per General Condition Of Tender 40.00 3 Seater Visitor Chair Supply Of Orbit 3 Seater Visitors Chair, *Cushioned Seat And Back *Silver Grey Finish With Arms Model No. Sj-708La Of Featherlite / Godrej Or Equavalent As Directed By The Engineer-In-Charge. With 3 Years Warranty Finish As Per General Condition Of Tender 20.00 Open Rack Steel Slotted Angular Racks, Open Type With 6 Shelves Making 5 Compartments Of Size 1800Mm X 900Mm X 450 Mm, Cr Sheet Shelfs 1.2Mm Thickness With An Angle Of 2 Mm Thickness And Size: 40 Mm X 60 Mm, With 8 Corner Brackets Of 2 Mm Thickness. Finish: Sheet Metal Components: All Dents, Burrs And Sharp Edges Shall Be Removed From The Various Components. The Components Shall Be Individually Pickled, Scrubbed And Rinsed To Remove Grease, Rust, Scale Or Any Other Foreign Element. Immediately After Pickling, All The Mild Steel Parts Shall Be Given Phosphate Treatment Conforming To Class C Or Is : 3618-1966. The Process For Application Of Phosphate Coating Shall Be In Accordance With Is: 6005-12970. Two Coats To Enamel Paint ( Colour Grey Is Preferred ) Shall Then Be Applied As Follows: Finish Coat With Enamel Paint Conforming To Is : 151-1950, Is : 2932-1974 Or Is : 2933-1975. In The Case Of Stoving Enamel The Components Shall Thereafter Be Backed At A Specified Temperature In An Over Heated Uniformly. The Finish Shall Be Smooth And Uniform With A Hard And Touch Film Of Enamel, Strongly Adhering To The Surface. The Finish Shall Be Free From All Visible Defects And Shall Not Chip When Tapped Lightly With A Dull Pointed Instrument. Note: Putty Shall Be Applied To All The Surfaces Requiring Filling And Shall Conform To Is: 110-1968. Tests: The Performance Tests Required For The Finished Racks Shall Be Carried Out As Per The Methodology Mentioned In The Is 6189:1985. The Rack Shall Have A Name Plate Or Label Fixed To It Showing The Manufacturer’S Name, Initials Or Recognized Trademark. Hospital Furniture Items Shall Be Subjected To Tests In Accordance With The Requirements Of Relevant Specifications. However, The Painted Furniture Items Shall Also Satisfy The Adhesion Test And In Addition Satisfy The Performance Test Give Below: Shoes: These Shall Be Manufactured From Pvc / Hard Rubber Bush. Nominal Height Of The Shoe Shall Be 35 Mm. Outside Dimensions Of 3Mm. With 3 Years Warranty Finish As Per General Condition Of Tender 4.00 Table For Immunization / Fp / Counselling Dimensions: 900 W X 590 D X 750 H Mm Material : A ) Plb / Plt – Top Impregnated Base 18Mm Thickness With 2Mm Thick Hot Pressed Pvc Beading C ) Understructure : This Table Comes With A Square Tube Understructure With Prime Quality C.R Tube Steel. All Steel Tubes Used For Desk Under Structures Are As Per Is-3601-1984, Is- 7138-1973, Is-4923-1985. Top Frame And Legs :30 X 30 C.R Square Tube 1.2Mm Thickness With Two Foot Steps. 5.00 Table For Seminar / Conference Hall Conference Hall Table Size: 2100 X 1200 X 740 Mm. Table Top :- The Top Of The Table Shall Be Made Of 38 Mm Composite Mdf ( 25Mm Plain Mdf Board + 12Mm Plain Mdf ) With Pvc Membrane 0.4Mm Thick Pvc Membrane Foil Using Wrap Around Technology. The Foil Is Pre-Coated With Pu Layer For Better Scratch And Wear Resistance. 0.6Mm Balancing Laminate On Bottom Surface. Understructure :- The Legs Of The Table Shall Be 25 Mm Thk , Post Formed Particle Board With Round Edge. Modesty Panel :- The Modesty Panel Of The Table Shall Be 600Mm High Made Of 18Mm Thk Prelam Particle Board. Vertibrae Fixed To Work Surface From Bottom Side For Entering Wires The Wire Carrying Is Facilitated Through The Hollow Space Between Plastic Components.
