|
| 1 | Excavation for roadwork in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m But Excluding G.S.T. |
| 2 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory rollerin stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density.But Excluding G.S.T. |
| 3 | Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. But Excluding G.S.T. |
| 4 | Supply & laying of 100mm thick Precast cement concerete I-Shape\" Interlocking paver blocks ISI markconfirming to IS: 15658-2006 with top layer of minimum 5 mm thicknesshaving plan dimension 200x(160+120mm) of O.P. Cement , smooth high gloss finish, skid resistant; manufactured from rubber moulds through vibro-compression mechanism. The compressive strength of concrete paver block shall not be less than 50Mpaand weight 5 kg perincluding cost of material, with a blanket layer of 4.00cm. thick fine sand. includinglabour, T & Petc required for proper completion of the work as directed by Engineer-in-charge. But Excluding G.S.T. |
| 5 | Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.But Excluding G.S.T. |
| 6 | Providing and laying bituminous concrete withhigher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4per centof mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects.But Excluding G.S.T. |
| 7 | Providing and laying of hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC: 35. The finished surface to be level uniform and free from streaks and holes. (SI. New Item No. 5) complet as per sepecifications.But Excluding G.S.T. |
| 8 | Provide Sets of 5 mm thick Bar Marking of hot applied thermoplastic compound 5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC: 35. The finished surface to be level uniform and free from streaks and holes. (SI. New Item No. 5) complet as per sepecifications.But Excluding G.S.T. |
| 9 | M-150 Brick Work but in 1:4 (One cement & four Corse sand) mortar. including supply of all materials labour, Tools & plants etc. required for proper completion of the work. But Excluding G.S.T. |
| 10 | Struck pointing with cement mortar consisting of 1 part cement and 2 parts of fine sand of 1.25 Fineness modulus.But Excluding G.S.T. |
| 11 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC 67:2012 made of high intensity grade sheeting vide clause 801.3, fried over aluminum sheeting type-IV 1.5 mm thick supported on a mild steel angle iron post 75mm x 75 mm x6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm x 45 cm x 60 cm below ground level as per approved drawing. The retro-reflective sheeting shall be tested for 3 year outdoor weathering test in Indian conditions as per IRC 67: 2012 & proof of the same in form of government report shall be uploaded with quoting tender.But Excluding G.S.T. |
| 12 | 45 x 90 Cm Two Way object Hazard.But Excluding G.S.T. |
| 13 | 30 x 90 Cm )Left / Right) object Hazard. But Excluding G.S.T. |
| 14 | 155 x 60 Cm Double Chevron.But Excluding G.S.T. |
| 15 | d) 80mm x 60mm rectangular with diffinitation plate (20cm x 50cm) (Left, Right, Speed Limit, Zebra, Hazard, Stop Board, Speed Hump Sign).But Excluding G.S.T. |
| 16 | c) 60 cm Circular with diffinitation plate (20 cm x 60 cm) Non Over Tacking Sign.But Excluding G.S.T. |
| 17 | d) 80mm x 60mm rectangular with diffinitation plate (20cm x 50cm) (School Board).But Excluding G.S.T. |
| 18 | Reflective Raised Pavement Marker Providing and fixing of raised pavement markers (Cat Eye) Type x-ASTMD-4956-04 Avery Dennision/3m(USA Make) having moulded body of polycarbonate, ASA, HIPS or ABS able to support a load of 13.635 M.T. tested in accordance with ASTMD 4280 type H and other requirement mentioned in MoRT&H Circular, its reflective lens made of micro prismatic lens (capable of providing total internal reflection of light), electronically welded to the body. The length, height and width of the body shall not exceed 130 mm, 20 mm and 105 mm respectively, The area of each reflective surface shall not be less than 13 Sq. cm . on each side sloping at the angle of 35 + 5 degree to the base to ensure maximum reflectively.But Excluding G.S.T. it shall comply to specification of Category A of MoRT&H circular no. RW/NH 33023/10/97-DO-III dated 11.06.97 lenses shall be moulded of methyl methecrylate conforming to ASTMD 788 or equivalent.With 7 years warranty. Rate shall be inclusive of all taxes, royalty, etc. All T&P/ machine material and labour required for proper completion of work.But Excluding G.S.T. |
| 19 | Supplying & fixing of Linear Delineator System (LDS)panels made of Micro prismatic Retro Reflective sheeting Type XI duly laminated on thin aluminium foil to a unique corrugated shape to provide retro reflection across wide range of observations and external angles. Each LDS panel should be of nominal length of 33 inch and each ridge shall be approximately 0.34 inch high. Each LDS panel is to be firmly fixed onexistingConcrite / brick work with 16 NosFastner/ screwas per IRC 79-2019 -Rates are inclusive of all taxes, royalty,etc. all T&P/machine material and labour required for proper completion of work.Note : The Composite warranty jointly signed by original manufacturer & authorized converter of at least 7 years shall be furnished on non judicial stamp of required denomination.But Excluding G.S.T. |
