Tender For Const Of Gos, Sos And Ors Living Accomodation Including Kitchen And Toilet At Stg Camp Migging Of 49 Bn Itbp
Tender Value
2.05 Crore
Estimated cost
Bid Submission
12 Jun 2023
0 days left
EMD
4.12 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
migging → Arunachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Const Of Gos, Sos And Ors Living Accomodation Including Kitchen And Toilet At Stg Camp Migging Of 49 Bn Itbp
BOQ
| Sl. No. | Item Description |
| 1 | Earth workexcavation by manual means over area (exceeding 30 cm in depth1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.: All kind of soil |
| 2 | Excavation work in foundation trenches or drains not exceeding 1.5 m in width or 10 sqm on plan including dresing of sides and ramming of bottoms lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed , within a lead of 50 m.All kind of soil |
| 3 | Filling available excavated earth ( excluding rocks) in plinth side of foundation, under floors in layers not exceeding 20 cm in depthincluding, watering, ramming consolidating and dressing completelead up to 50 m and lift up to 1.5 m |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:5:10 (1 Cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) |
| 6 | Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete :. Cement Ordinary portland43 grade conforming to IS No: 8112- 1989:1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 7 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75 mm bed by dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth |
| 8 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate20 mm nominal size) |
| 9 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate20 mm nominal size) |
| 10 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarsesand (zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 11 | Centering and shutturing incl. strutting, proping etc and removal of form work for all heights:Foundations, footings, bases of columns, etc. for mass concrete |
| 12 | Centering and shutturing incl. strutting, proping etc and removal of form work for all heights:Suspended floors, roofs, landings, balconies and access platform |
| 13 | Centering and shutturing incl. strutting, proping etc and removal of form work for all heights: Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 14 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 15 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 Cement : 6 coarse sand) |
| 16 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) with First class local wood(Tita champa / Pine/Tiger): Local wood |
| 17 | Providing wood work in frames of false ceiling, partition and other frames fixed in position: First class local wood(Tita champa / Pine/tiger) |
| 18 | Providing and fixing panelled or panelled and glazed shutters doors, windows and clerestory windows including ISI marked black enameled M.S. butt hinges with necessary screws (screws should be of stainlesss steel and brand Magnum/ Nettlefold/Amul) excluding, panelling which will be paid for seperately (Thickness of shutters should be 35mm): first class local wood (Tita champa / Pine)confermingIS- 399:1963 (Weight of should be 545 Kg/ M3): 35 mm thick shutterrs |
| 19 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :First class local wood(Tita champa / Pine) |
| 20 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws: First class local wood (Tita champa/Pine/tiger)-35mm thick |
| 21 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws; 35 mm thick shutters: With ISI marked M.S. pressed butt hinges bright finished of required size: First class local wood (Tita champa/Pine/tiger) |
| 22 | Providingand fixing 6 mm thick commercial water proof plyof approved quality in false ceiling. |
| 23 | P/f wooden beading with iron screws and priming coat on unexposed surface complete. First class local wood(Tita champa / Pine/tiger)-5.x12mm |
| 24 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. complete.: fixed to windows openings/wooden frame with screws |
| 25 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than gradeAC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm |
| 26 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :250x10mm |
| 27 | Providing and fixing Aluminium tower bolt100x10mm |
| 28 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :Size 125mm |
| 29 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : Size 100 mm |
| 30 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.: Twin rubber stopper |
| 31 | Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 32 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 33 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 34 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). |
| 35 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 36 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete :Ridges plain (500 - 600mm) |
| 37 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers :Barge board/Eave Board on roof edge complete : |
| 38 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 39 | Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer , of required shade and colour complete, as per manufacturer\"s specification. : Two or more coats on new work |
| 40 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer |
| 41 | Finishing walls withAcrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 42 | Applying priming coat with: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 43 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 44 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer , over the plastered wall surface to prepare the surface even and smooth complete. |
| 45 | Providing and fixing white vitreous china pedestal type water closet (European type W .C. pan) with seat and lid, 10 litre low level white P .V .C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 46 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer each 2984.20 |
| 47 | Providing andfixingwhitevitreouschinapedestalfor wash basin completely recessed at the back for the reception of pipes and fittings. |
| 48 | Providing and fixing Stainless SteelAISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink without drain board: 610x460 mm bowl depth 200 mm |
| 49 | Providing and fixing 8 mm dia C.P . / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W .C. of quality and make as approved by Engineer - in -charge. |
| 50 | Providing and fixing P .V .C. waste pipe for sink or wash basin including P .V .C. waste fittings complete. : Semi rigid pipe : 32 mm dia |
| 51 | Providing and fixing P .V .C. waste pipe for sink or wash basin including P .V .C. waste fittings complete. : Semi rigid pipe : 40 mm dia |
| 52 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing: Rectangular shape 453x357 mm |
| 53 | Providing and fixing toilet paper holder : C.P . Brass |
| 54 | Providing and fixing PVC trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet |
| 55 | Providing and fixing CP Brass Towel rack complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.: 600 mm long towel rack |
| 56 | Providing and fixing CP brass glass shelf 600 mm long with brackets fixed with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 57 | Providing and fixing CP brass corner glass shelfwith brackets fixed with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 58 | Providing and fixing CP brass Soap Dishwith brackets fixed with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 59 | Providing and fixing G .I. Pipes complete with G .I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore |
| 60 | Providing and fixing G .I. pipes complete with G .I. fittings including trenching and refilling etc.: 20 mm dia nominal bore |
| 61 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore |
| 62 | Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length- 15 mm nominal bore |
| 63 | Providing and fixing C.P . brass shower rose with 15 or 20 mm inlet : 150 mm diameter |
| 64 | Providing and fixing G.I. Union in G .I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 20 mm nominal bore |
| 65 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 66 | Providing and fixing C.P . brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore |
| 67 | Providing and fixing C.P . brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 : 15 mm nominal bore |
| 68 | Providing and fixing C.P . brass Wall Mixer with 115 mm Long Bend Pipe for Connection to Overhead Shower (with Bush & Piston Divertor Fitting) with Aerato with all accessories of approved quality conforming to IS standards. 15 mm nominal bore |
| 69 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P type:With common burnt clay F .P .S. (non modular) bricks ofclass designation 7.5 each |
| 70 | Constructing brick masonry manhole in cement mortar 1:4 ( 1cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F .P .S. (non modular) bricks of class designation 7.5 |
| 71 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F .P .S. (non modular) bricks of class designation 7.5 |
| 72 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W . drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F .P .S. (non modular) bricks of class designation 7.5 |
| 73 | Providing and fixing soil waste and vent pipes 100 mm dia of brand: 100 mm dia PVC socketed pipe as per IS:3989 |
| 74 | Providing and fixing soil waste and vent pipes 75 mm dia of brand: PVC socketed pipe as per IS:3989 75 mm dia |
| 75 | Providing and fixing plain bend of required degree: 100 mm dia PVC bend as per IS:3989 |
| 76 | Providing and fixing plain bend of required degree: 75mm dia PVC bend as per IS:3989 |
| 77 | Providing and fixing bend with access door of required degree: 100 mm dia PVC door bend as per IS:3989 |
| 78 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B |
| 79 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 80 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.: 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 81 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 82 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required |
| 83 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 84 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. |
| 85 | Supplying and fixing PVC batten/ angle holder including connections etc. as required. |
| 86 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8way, Double door Each |
| 87 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole |
| 88 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amp |
| 89 | SITC of 1200mm 5 star rated ceiling fan for 230V 50Hz AC Supply including wiring the down rods of standerd lenth (up to 300mm) with 1.5Sqmm FRLS PVC Insulated copper conductor single core cable(Excel star 1200mm white Ceiling Fan) |
| 90 | S/F of fresh air exhust fan of 225mm sweep in the existing opening i/c making the hole to suite the size of the above fan making good the damge connection testing& commissioning as reqd. ( heavy duty not less then 50Watt i/c louvers & shutters etc) |
| 91 | SITC of surface mounted 20 watt LED Batten (4 Ft) with wiring up to terminal block connection complete etc. as reqd. |
| 92 | SITC of 5 watt LED Batten (1 ft) surface mounting mirror light fitting having white colour along with 1.5Sqmm FRLS PVC Copper conductor single core cable earthing as per reqd. |
| 93 | Supply, Installation, testing and commissioning of fency wall bracket /ceiling fittings of all sizes and shapes containing iupto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required. |
| 94 | SITC of 25 litre capacity storage water heater pressure rate 6.5bar 2000watts operting 220-240Vz with4sqmm FRLS PVC Copper conductor single core cable earthing as per reqd. |
| 95 | SITC of 3 litre capacityinstant water heater 3000watts operting 220-240Vz with4sqmm FRLS PVC Copper conductor single core cable earthing as per reqd. |
| 96 | Supply, Installation, testing and commissioning of fency wall Light fittings of all sizes and shapes containing iupto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required. |
AI Tender Summary
Tender Timeline
May 29, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedJun 12, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 13, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender